Texas Instruments TLC1549IP, TLC1549IDR, TLC1549ID, TLC1549CP, TLC1549CDR Datasheet

TLC1549C, TLC1549I, TLC1549M 10-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL

SLAS059C ± DECEMBER 1992 ± REVISED MARCH 1995

D10-Bit-Resolution A/D Converter

DInherent Sample and Hold

DTotal Unadjusted Error . . . ± 1 LSB Max

DOn-Chip System Clock

DTerminal Compatible With TLC549 and TLV1549

DCMOS Technology

D, JG, OR P PACKAGE

(TOP VIEW)

REF +		1	8		VCC
ANALOG IN		2	7			I/O CLOCK
REF±		3	6			DATA OUT
GND		4	5			CS

FK PACKAGE (TOP VIEW)

description

The TLC1549C, TLC1549I, and TLC1549M are 10-bit, switched-capacitor, successiveapproximation analog-to-digital converters. These devices have two digital inputs and a

3-state output [chip select (CS), input-output clock (I/O CLOCK), and data output (DATA OUT)] that provide a three-wire interface to the serial port of a host processor.

The sample-and-hold function is automatic. The converter incorporated in these devices features differential high-impedance reference inputs that facilitate ratiometric conversion, scaling, and isolation of analog circuitry from logic and supply noise. A switched-capacitor design allows lowerror conversion over the full operating free-air temperature range.

	NC	REF+	NC	V	NC
				CC
NC	3	2	1	20 19		NC
	4				18
ANALOG IN	5				17	I/O CLOCK
NC	6				16	NC
REF±	7				15	DATA OUT
NC	8				14	NC
	9	10 11 12 13
	NC	GND	NC	CS	NC
NC ± No internal connection

The TLC1549C is characterized for operation from 0°C to 70°C. The TLC1549I is characterized for operation from ±40°C to 85°C. The TLC1549M is characterized for operation over the full military temperature range of ±55°C to 125°C.

AVAILABLE OPTIONS

		PACKAGE
TA
	SMALL OUTLINE	CHIP CARRIER	CERAMIC DIP	PLASTIC DIP
	(D)	(FK)	(JG)	(P)
0°C to 70°C	TLC1549CD	Ð	Ð	TLC1549CP
± 40°C to 85°C	TLC1549ID	Ð	Ð	TLC1549IP
± 55°C to 125°C	Ð	TLC1549MFK	TLC1549MJG	Ð

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.

Copyright 1995, Texas Instruments Incorporated

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

1

TLC1549C, TLC1549I, TLC1549M

10-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL

SLAS059C ± DECEMBER 1992 ± REVISED MARCH 1995

functional block diagram

REF + REF ±

	1	3

ANALOG IN

I/O CLOCK CS

		10-Bit
		Analog-to-Digital
		Converter
		(switched capacitors)
		10
2	Sample and	Output	10	10-to-1 Data	6
	Hold	Data		Selector and	DATA OUT
		Register		Driver
				4
		System Clock,
		Control Logic,
		and I/O
		Counters
7
5

Terminal numbers shown are for the D, JG, and P packages only.

typical equivalent inputs

INPUT CIRCUIT IMPEDANCE DURING SAMPLING MODE

INPUT CIRCUIT IMPEDANCE DURING HOLD MODE

1 kΩ TYP

ANALOG IN

		ANALOG IN
	Ci = 60 pF TYP	5 MΩ TYP
	(equivalent input
	capacitance)

2	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

								TLC1549C, TLC1549I, TLC1549M
								10-BIT ANALOG-TO-DIGITAL CONVERTERS
								WITH SERIAL CONTROL
								SLAS059C ± DECEMBER 1992 ± REVISED MARCH 1995
						Terminal Functions
		TERMINAL		I/O				DESCRIPTION
		NAME	NO.
	ANALOG IN		2	I	Analog signal input. The driving source impedance should be ≤ 1 kΩ. The external driving source to ANALOG IN
					should have a current capability ≥ 10 mA.
			5	I	Chip select. A high-to-low transition on			resets the internal counters and controls and enables DATA OUT and
	CS						CS
					I/O CLOCK within a maximum of a setup time plus two falling edges of the internal system clock. A low-to-high
					transition disables I/O CLOCK within a setup time plus two falling edges of the internal system clock.
	DATA OUT		6	O	This 3-state serial output for the A/D conversion result is in the high-impedance state when					is high and active
									CS
					when CS is low. With a valid chip select, DATA OUT is removed from the high-impedance state and is driven to
					the logic level corresponding to the MSB value of the previous conversion result. The next falling edge of I/O
					CLOCK drives DATAOUT to the logic level corresponding to the next most significant bit, and the remaining bits
					are shifted out in order with the LSB appearing on the ninth falling edge of I/O CLOCK. On the tenth falling edge
					of I/O CLOCK, DATA OUT is driven to a low logic level so that serial interface data transfers of more than ten clocks
					produce zeroes as the unused LSBs.
	GND		4		The ground return for internal circuitry. Unless otherwise noted, all voltage measurements are with respect to GND.
	I/O CLOCK		7	I	Input/output clock. I/O CLOCK receives the serial I/O CLOCK input and performs the following three functions:
					1)	On the third falling edge of I/O CLOCK, the analog input voltage begins charging the capacitor array and
						continues to do so until the tenth falling edge of I/O CLOCK.
					2)	It shifts the nine remaining bits of the previous conversion data out on DATA OUT.
					3)	It transfers control of the conversion to the internal state controller on the falling edge of the tenth clock.
	REF +		1	I	The upper reference voltage value (nominally VCC) is applied to REF +. The maximum input voltage range is
					determined by the difference between the voltage applied to REF + and the voltage applied to REF ±.
	REF ±		3	I	The lower reference voltage value (nominally ground) is applied to REF ±.
	VCC		8		Positive supply voltage

detailed description

With chip select (CS) inactive (high), I/O CLOCK is initially disabled and DATA OUT is in the high impedance state. When the serial interface takes CS active (low), the conversion sequence begins with the enabling of I/O CLOCK and the removal of DATA OUT from the high-impedance state. The serial interface then provides the I/O CLOCK sequence to I/O CLOCK and receives the previous conversion result from DATA OUT. I/O CLOCK receives an input sequence that is between 10 and 16 clocks long from the host serial interface. The first ten I/O clocks provide the control timing for sampling the analog input.

There are six basic serial interface timing modes that can be used with the TLC1549. These modes are determined by the speed of I/O CLOCK and the operation of CS as shown in Table 1. These modes are (1) a fast mode with a 10-clock transfer and CS inactive (high) between transfers, (2) a fast mode with a 10-clock transfer and CS active (low) continuously, (3) a fast mode with an 11to 16-clock transfer and CS inactive (high) between transfers, (4) a fast mode with a 16-bit transfer and CS active (low) continuously, (5) a slow mode with an 11to 16-clock transfer and CS inactive (high) between transfers, and (6) a slow mode with a 16-clock transfer and CS active (low) continuously.

The MSB of the previous conversion appears on DATA OUT on the falling edge of CS in mode 1, mode 3, and mode 5, within 21 μs from the falling edge of the tenth I/O CLOCK in mode 2 and mode 4, and following the sixteenth clock falling edge in mode 6. The remaining nine bits are shifted out on the next nine falling edges of I/O CLOCK. Ten bits of data are transmitted to the host serial interface through DATA OUT. The number of serial clock pulses used also depends on the mode of operation, but a minimum of ten clock pulses is required for conversion to begin. On the tenth clock falling edge, the internal logic takes DATA OUT low to ensure that the remaining bit values are zero if the I/O CLOCK transfer is more than ten clocks long.

Table 1 lists the operational modes with respect to the state of CS, the number of I/O serial transfer clocks that can be used, and the timing on which the MSB of the previous conversion appears at the output.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

3

TLC1549C, TLC1549I, TLC1549M

10-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL

SLAS059C ± DECEMBER 1992 ± REVISED MARCH 1995

detailed description

Table 1. Mode Operation

					NO. OF			MSB AT Terminal 6²			TIMING
MODES			CS
					I/O CLOCKS						DIAGRAM
	Mode 1	High between conversion cycles			10			CS		falling edge	Figure 6
Fast Modes	Mode 2	Low continuously			10		Within 21 μs				Figure 7
					11 to 16³
	Mode 3	High between conversion cycles					CS falling edge				Figure 8
	Mode 4	Low continuously			16³		Within 21 μs				Figure 9
	Mode 5	High between conversion cycles			11 to 16³					falling edge	Figure 10
Slow Modes							CS
	Mode 6	Low continuously			16³		16th clock falling edge				Figure 11

² This timing also initiates serial interface communication. ³ No more than 16 clocks should be used.

All the modes require a minimum period of 21 μs after the falling edge of the tenth I/O CLOCK before a new transfer sequence can begin. During a serial I/O CLOCK data transfer, CS must be active (low) so that I/O CLOCK is enabled. When CS is toggled between data transfers (modes 1, 3, and 5), the transitions at CS are recognized as valid only if the level is maintained for a minimum period of 1.425 μs after the transition. If the transfer is more than ten I/O clocks (modes 3, 4, 5, and 6), the rising edge of the eleventh clock must occur within 9.5 μs after the falling edge of the tenth I/O CLOCK; otherwise, the device could lose synchronization with the host serial interface and CS has to be toggled to restore proper operation.

fast modes

The TLC1549 is in a fast mode when the serial I/O CLOCK data transfer is completed within 21 μs from the falling edge of the tenth I/O CLOCK. With a ten-clock serial transfer, the device can only run in a fast mode.

mode 1: fast mode, CS inactive (high) between transfers, 10-clock transfer

In this mode, CS is inactive (high) between serial I/O CLOCK transfers and each transfer is ten clocks long. The falling edge of CS begins the sequence by removing DATA OUT from the high-impedance state. The rising edge of CS ends the sequence by returning DATA OUT to the high-impedance state within the specified delay time. Also, the rising edge of CS disables I/O CLOCK within a setup time plus two falling edges of the internal system clock.

mode 2: fast mode, CS active (low) continuously, 10-clock transfer

In this mode, CS is active (low) between serial I/O CLOCK transfers and each transfer is ten clocks long. After the initial conversion cycle, CS is held active (low) for subsequent conversions. Within 21 μs after the falling edge of the tenth I/O CLOCK, the MSB of the previous conversion appears at DATA OUT.

mode 3: fast mode, CS inactive (high) between transfers, 11to 16-clock transfer

In this mode, CS is inactive (high) between serial I/O CLOCK transfers and each transfer can be 11 to 16 clocks long. The falling edge of CS begins the sequence by removing DATA OUT from the high-impedance state. The rising edge of CS ends the sequence by returning DATA OUT to the high-impedance state within the specified delay time. Also, the rising edge of CS disables I/O CLOCK within a setup time plus two falling edges of the internal system clock.

mode 4: fast mode, CS active (low) continuously, 16-clock transfer

In this mode, CS is active (low) between serial I/O CLOCK transfers and each transfer must be exactly 16 clocks long. After the initial conversion cycle, CS is held active (low) for subsequent conversions. Within 21 μs after the falling edge of the tenth I/O CLOCK, the MSB of the previous conversion appears at DATA OUT.

slow modes

In a slow mode, the serial I/O CLOCK data transfer is completed after 21 μs from the falling edge of the tenth I/O CLOCK.

4	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TLC1549C, TLC1549I, TLC1549M 10-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL

SLAS059C ± DECEMBER 1992 ± REVISED MARCH 1995

mode 5: slow mode, CS inactive (high) between transfers, 11to 16-clock transfer

In this mode, CS is inactive (high) between serial I/O CLOCK transfers and each transfer can be 11 to 16 clocks long. The falling edge of CS begins the sequence by removing DATA OUT from the high-impedance state. The rising edge of CS ends the sequence by returning DATA OUT to the high-impedance state within the specified delay time. Also, the rising edge of CS disables I/O CLOCK within a setup time plus two falling edges of the internal system clock.

mode 6: slow mode, CS active (low) continuously, 16-clock transfer

In this mode, CS is active (low) between serial I/O CLOCK transfers and each transfer must be exactly 16 clocks long. After the initial conversion cycle, CS is held active (low) for subsequent conversions. The falling edge of the sixteenth I/O CLOCK then begins each sequence by removing DATA OUT from the low state, allowing the MSB of the previous conversion to appear immediately at DATA OUT. The device is then ready for the next 16 clock transfer initiated by the serial interface.

analog input sampling

Sampling of the analog input starts on the falling edge of the third I/O CLOCK, and sampling continues for seven I/O CLOCK periods. The sample is held on the falling edge of the tenth I/O CLOCK.

converter and analog input

The CMOS threshold detector in the successive-approximation conversion system determines each bit by examining the charge on a series of binary-weighted capacitors (see Figure 1). In the first phase of the conversion process, the analog input is sampled by closing the SC switch and all ST switches simultaneously. This action charges all the capacitors to the input voltage.

In the next phase of the conversion process, all ST and SC switches are opened and the threshold detector begins identifying bits by identifying the charge (voltage) on each capacitor relative to the reference (REF±) voltage. In the switching sequence, ten capacitors are examined separately until all ten bits are identified and then the charge-convert sequence is repeated. In the first step of the conversion phase, the threshold detector looks at the first capacitor (weight = 512). Node 512 of this capacitor is switched to the REF+ voltage, and the equivalent nodes of all the other capacitors on the ladder are switched to REF±. If the voltage at the summing node is greater than the trip point of the threshold detector (approximately one-half VCC), a bit 0 is placed in the output register and the 512-weight capacitor is switched to REF±. If the voltage at the summing node is less than the trip point of the threshold detector, a bit 1 is placed in the register and this 512-weight capacitor remains connected to REF+ through the remainder of the successive-approximation process. The process is repeated for the 256-weight capacitor, the 128-weight capacitor, and so forth down the line until all bits are determined.

With each step of the successive-approximation process, the initial charge is redistributed among the capacitors. The conversion process relies on charge redistribution to determine the bits from MSB to LSB.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

5