Texas Instruments TL054MJB, TL054MFKB, TL054MJ, TL054IN, TL054IDR Datasheet

	TL05x, TL05xA, TL05xY
	ENHANCED-JFET LOW-OFFSET
	OPERATIONAL AMPLIFIERS
	SLOS178 ± FEBRUARY 1997
D Direct Upgrades to TL07x and TL08x BiFET	D On-Chip Offset Voltage Trimming for
Operational Amplifiers	Improved DC Performance and Precision
D Faster Slew Rate (20 V/ s Typ) Without	Grades Are Available (1.5 mV, TL051A)
Increased Power Consumption	D Available in TSSOP for Small Form-Factor
	Designs

description

The TL05x series of JFET-input operational amplifiers offers improved dc and ac characteristics over the TL07x and TL08x families of BiFET operational amplifiers. On-chip zener trimming of offset voltage yields precision grades as low as 1.5 mV (TL051A) for greater accuracy in dc-coupled applications. Texas Instruments improved BiFET process and optimized designs also yield improved bandwidth and slew rate without increased power consumption. The TL05x devices are pin-compatible with the TL07x and TL08x and can be used to upgrade existing circuits or for optimal performance in new designs.

BiFET operational amplifiers offer the inherently higher input impedance of the JFET-input transistors, without sacrificing the output drive associated with bipolar amplifiers. This makes them better suited for interfacing with high-impedance sensors or very low-level ac signals. They also feature inherently better ac response than bipolar or CMOS devices having comparable power consumption.

The TL05x family was designed to offer higher precision and better ac response than the TL08x with the low noise floor of the TL07x. Designers requiring significantly faster ac response or ensured lower noise should consider the Excalibur TLE208x and TLE207x families of BiFET operational amplifiers.

AVAILABLE OPTIONS

						PACKAGED DEVICES				CHIP
			VIOmax
		T		SMALL	CHIP	CERAMIC	CERAMIC	PLASTIC	PLASTIC	FORM³
		A	AT 25°C	OUTLINE²	CARRIER	DIP	DIP	DIP	DIP	(Y)
				(D)	(FK)	(J)	(JG)	(N)	(P)
			800 V	TL051ACD	Ð	Ð	Ð	Ð	TL051ACP
				TL052ACD					TL052ACP
										TL051Y
	°	°		TL051CD					TL051CP
										TL052Y
	0 C to 70 C		1.5 mV	TL052CD	Ð	Ð	Ð	TL054ACN	TL052CP
										TL054Y
				TL054ACD
			4 mV	TL054CD	Ð	Ð	Ð	TL054CN	Ð
			800 V	TL051AID	Ð	Ð	Ð	Ð	TL051AIP
				TL052AID					TL052AIP
	± 40°C to 85°C			TL051ID					TL051IP	Ð
			1.5 mV	TL052ID	Ð	Ð	Ð	TL054AIN
									TL052IP
				TL054AID
			4 mV	TL054ID	Ð		Ð	TL054IN	Ð
			800 V	TL051AMD	TL051AMFK	Ð	TL051AMJG	Ð	TL051AMP
				TL052AMD	TL052AMFK		TL052AMJG		TL052AMP
	± 55°C to 125°C			TL051MD	TL051MFK		TL051MJG		TL051MP	Ð
			1.5 mV	TL052MD	TL052MFK	TL054AMJ		TL054AMN
							TL052MJG		TL052MP
				TL054AMD	TL054AMFK
			4 mV	TL054MD	TL054MFK	TL054MJ	Ð	TL054MN	Ð

² The D packages are available taped and reeled. Add R suffix to device type (e.g., TL054CDR). ³ Chip forms are tested at 25°C.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.

Copyright 1997, Texas Instruments Incorporated

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

1

TL05x, TL05xA, TL05xY

ENHANCED-JFET LOW-OFFSET

OPERATIONAL AMPLIFIERS

SLOS178 ± FEBRUARY 1997

description (continued)

Because BiFET operational amplifiers are designed for use with dual power supplies, care must be taken to observe common-mode input voltage limits and output swing when operating from a single supply. DC biasing of the input signal is required and loads should be terminated to a virtual-ground node at midsupply. Texas Instruments TLE2426 integrated virtual ground generator is useful when operating BiFET amplifiers from single supplies.

The TL05x are fully specified at ±15 V and ± 5 V. For operation in low-voltage and/or single-supply systems, Texas Instruments LinCMOS families of operational amplifiers (TLC-prefix) are recommended. When moving from BiFET to CMOS amplifiers, particular attention should be paid to the slew rate and bandwidth requirements, and also the output loading.

TL051

D, JG, OR P PACKAGE

(TOP VIEW)

OFFSET N1		1	8		NC
IN±		2	7		VCC +
IN+		3	6		OUT
VCC ±		4	5		OFFSET N2

		TL051
	FK PACKAGE
	(TOP VIEW)
	NC	OFFSET N1	NC	NC	NC
NC	3	2	1	20 19		NC
	4				18
IN±	5				17	VCC +
NC	6				16	NC
IN+	7				15	OUT
NC	8				14	NC
	9	10 11 12 13
	NC	CC±	NC	N2	NC
		V		OFFSET

NC ± No internal connection

TL052

D, JG, OR P PACKAGE

(TOP VIEW)

1OUT		1	8		VCC +
1IN±
		2	7		2OUT
1IN+		3	6		2IN±
VCC ±		4	5		2IN+

TL052

FK PACKAGE (TOP VIEW)

	NC	1OUT	NC	CC +	NC
				V
NC	3	2	1	20 19		NC
	4				18
1IN ±	5				17	2OUT
NC	6				16	NC
1IN+	7				15	2IN ±
NC	8				14	NC
	9	10 11 12 13
	NC	CC ±	NC	2IN +	NC
		V

TL054

D, J, OR N PACKAGE

(TOP VIEW)

1OUT	1	14	4OUT
1IN±	2	13	4IN±
1IN+	3	12	4IN+
VCC +	4	11	VCC ±
2IN+	5	10	3IN+
2IN±	6	9	3IN±
2OUT	7	8	3OUT

TL054

FK PACKAGE (TOP VIEW)

	1IN ±	1OUT	NC	4OUT	4IN ±
1IN +	3	2	1	20 19		4IN +
	4				18
NC	5				17	NC
VCC +	6				16	VCC ±
NC	7				15	NC
2IN +	8				14	3IN +
	9	10 11 12 13
	2IN ±	2OUT	NC	3OUT	3IN ±

2	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

symbol (each amplifier)

IN ±

IN +

TL05x, TL05xA, TL05xY

ENHANCED-JFET LOW-OFFSET

OPERATIONAL AMPLIFIERS

SLOS178 ± FEBRUARY 1997

± OUT +

equivalent schematic (each amplifier)

				VCC +
				Q10
		Q2				Q15	JF3
			Q3
			Q7
			Q6			Q16
				Q11	Q13
	IN +			Q12	R7
			D1			R9
	IN ±						OUT
				R5
	JF1		JF2
			C1		R8
			Q4		Q14	Q17
	Q1			Q8
	OFFSET N1		Q5	Q9		R10	D2
See Note A
	OFFSET N2
			R4	R6
	R1	R2
			R3

VCC ±

NOTE A: OFFSET N1 and OFFSET N2 are only available on the TL051x.

ACTUAL DEVICE COMPONENT COUNT²

COMPONENT	TL051	TL052	TL054
Transistors	20	34	62
Resistors	10	19	37
Diodes	2	3	5
Capacitors	1	2	4

² These figures include all four amplifiers and all ESD, bias, and trim circuitry.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

3

TL05x, TL05xA, TL05xY

ENHANCED-JFET LOW-OFFSET

OPERATIONAL AMPLIFIERS

SLOS178 ± FEBRUARY 1997

TL051Y chip information

This chip, when properly assembled, displays characteristics similar to the TL051. Thermal compression or ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive epoxy or a gold-silicon preform.

BONDING PAD ASSIGNMENTS

							(7)		(6)		IN +		(3)		VCC+
														+			(7)	(6)
											IN ±		(2)	±			(4)		OUT
													(1)
											OFFSET N1					VCC ±
													(5)
									(5)		OFFSET N2
			63
									(4)		CHIP THICKNESS: 15 MILS TYPICAL
											BONDING PADS: 4 × 4 MILS MINIMUM
											TJmax = 150°C
							(1)				TOLERANCES ARE ± 10%.
											ALL DIMENSIONS ARE IN MILS.
							(2)		(3)		PIN (4) IS INTERNALLY CONNECTED
											TO BACKSIDE OF CHIP.
									43

4	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TL05x, TL05xA, TL05xY

ENHANCED-JFET LOW-OFFSET

OPERATIONAL AMPLIFIERS

SLOS178 ± FEBRUARY 1997

TL052Y chip information

This chip, when properly assembled, displays characteristics similar to the TL052. Thermal compression or ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive epoxy or a gold-silicon preform.

	BONDING PAD ASSIGNMENTS
(7)	(6)	(5)
(8)		(4)
72
(1)	(2)	(3)
	66

				VCC+
	(3)					(8)
1IN +			+
							(1)		1OUT
1IN ±	(2)		±
							(5)
			+						2IN +
2OUT	(7)
						±	(6)		2IN ±
						(4)
				VCC ±

CHIP THICKNESS: 15 MILS TYPICAL BONDING PADS: 4 × 4 MILS MINIMUM TJmax = 150°C

TOLERANCES ARE ± 10%.

ALL DIMENSIONS ARE IN MILS.

PIN (4) IS INTERNALLY CONNECTED TO BACKSIDE OF CHIP.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

5

TL05x, TL05xA, TL05xY

ENHANCED-JFET LOW-OFFSET

OPERATIONAL AMPLIFIERS

SLOS178 ± FEBRUARY 1997

TL054 chip information

This chip, when properly assembled, displays characteristics similar to the TL054C. Thermal compression or ultrasonic bonding may be used on the doped-aluminum bonding pads. These chips may be mounted with conductive epoxy or a gold-silicon preform.

					BONDING PAD ASSIGNMENTS
									VCC+
				(1)	(14)
							(3)				(4)
						1IN +		+
												(1)		1OUT
				(2)	(13)	1IN ±	(2)	±
												(5)
								+						2IN +
						2OUT	(7)
												(6)
								±						2IN ±
				(3)	(12)	3IN +	(10)
								+
												(8)		3OUT
						3IN ±	(9)	±
												(12)
								+						4IN +
						4OUT	(14)
										±		(13)		4IN ±
										(11)
									VCC ±
				(4)	(11)
122

							CHIP THICKNESS: 15 MILS TYPICAL
							BONDING PADS: 4 × 4 MILS MINIMUM
							TJmax = 150°C
(5)					(10)		TOLERANCES ARE ± 10%.
							ALL DIMENSIONS ARE IN MILS.
							PIN (11) IS INTERNALLY CONNECTED
							TO BACKSIDE OF THE CHIP.
(6)					(9)
		(7)	(8)		(8)
(6)		(7)			(9)
			71

6	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TL05x, TL05xA, TL05xY

ENHANCED-JFET LOW-OFFSET

OPERATIONAL AMPLIFIERS

SLOS178 ± FEBRUARY 1997

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)²

Supply voltage, VCC + (see Note 1) . . . . . .	. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . 18 V
Supply voltage, VCC ± (see Note 1) . . . . . . .	. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . ±18 V
Differential input voltage (see Note 2) . . . . .	. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . ± 30 V
Input voltage range, VI (any input, see Notes 1 and 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .		. . . . . . . . ± 15 V
Input current, II (each input) . . . . . . . . . . . . .	. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . ± 1 mA
Output current, IO (each output) . . . . . . . . .	. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . ± 80 mA
Total current into VCC+ . . . . . . . . . . . . . . . . .	. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . 160 mA
Total current out of VCC± . . . . . . . . . . . . . . .	. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . 160 mA
Duration of short-circuit current at (or below) 25°C (see Note 4) . . . . . . . . . . . . . . . . . . . . . . . . .		. . . . . unlimited
Continuous total power dissipation . . . . . . .	. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, TA:	C suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . 0°C to 70°C
	I suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	±40°C to 85°C
	M suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	±55°C to 125°C
Storage temperature range . . . . . . . . . . . . . .	. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	±65°C to 150°C
Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .		. . . . . . . 260°C
Lead temperature 1,6 mm (1/16inch) from case for 10 seconds: D, N, or P package . . . . . . .		. . . . . . . 260°C
Lead temperature 1,6 mm (1/16inch) from case for 60 seconds: J or JG package . . . . . . . . .		. . . . . . . 300°C

²Stresses beyond those listed under ªabsolute maximum ratingsº may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under ªrecommended operating conditionsº is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VCC + and VCC ± .

2.Differential voltages are at IN+ with respect to IN ±.

3.The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 V, whichever is less.

4.The output may be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum dissipation rating is not exceeded.

DISSIPATION RATING TABLE

	PACKAGE	TA ≤ 25°C	DERATING FACTOR	TA = 70°C	TA = 85°C	TA = 125°C
		POWER RATING	ABOVE TA = 25°C	POWER RATING	POWER RATING	POWER RATING
	D±8	725 mW	5.8 mW/°C	464 mW	377 mW	145 mW
	D±14	950 mW	7.6 mW/°C	608 mW	494 mW	190 mW
	FK	1375 mW	11.0 mW/°C	880 mW	715 mW	275 mW
	J	1375 mW	11.0 mW/°C	880 mW	715 mW	275 mW
	JG	1050 mW	8.4 mW/°C	672 mW	546 mW	210 mW
	N	1575 mW	12.6 mW/°C	1008 mW	819 mW	315 mW
	P	1000 mW	8.0 mW/°C	640 mW	520 mW	200 mW

recommended operating conditions

			C SUFFIX		I SUFFIX		M SUFFIX		UNIT
			MIN	MAX	MIN	MAX	MIN	MAX
	Supply voltage, VCC ±		± 5	± 15	± 5	± 15	± 5	± 15	V
	Common-mode input voltage, VIC	VCC ± = ± 5 V	± 1	4	± 1	4	± 1	4	V
		VCC ± = ± 15 V	± 11	11	± 11	11	± 11	11
	Operating free-air temperature, TA		0	70	± 40	85	± 55	125	°C

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

7

TL05x, TL05xA, TL05xY

ENHANCED-JFET LOW-OFFSET

OPERATIONAL AMPLIFIERS

SLOS178 ± FEBRUARY 1997

TL051C and TL051AC electrical characteristics at specified free-air temperature

TL051C, TL051AC

T ²

PARAMETER

TEST CONDITIONS

V

= ± 5 V

V

±

= ± 15 V

UNIT

A

CC ±

CC

MIN

TYP

MAX

MIN

TYP

MAX

TL051C

25°C

0.75

3.5

0.59

1.5

VIO

Input offset voltage

Full range

4.5

2.5

mV

TL051AC

25°C

0.55

2.8

0.35

0.8

VO = 0,

Full range

3.8

1.8

25°C to

VIC = 0,

TL051C

8

8

Temperature coefficient

70°C

αVIO

RS = 50 Ω

µ V/

°

C

of input offset voltage³

TL051AC

25°C to

8

8

25

70°C

Input offset voltage

25°C

0.04

0.04

µV/mo

long-term drift§

IIO

Input offset current

VO = 0,

VIC = 0,

25°C

4

100

5

100

pA

See Figure 5

70°C

0.02

1

0.025

1

nA

IIB

Input bias current

VO = 0,

VIC = 0,

25°C

20

200

30

200

pA

See Figure 5

70°C

0.15

4

0.2

4

nA

± 1

± 2.3

± 11

± 12.3

25°C

to

to

to

to

VICR

Common-mode input

4

5.6

11

15.6

V

voltage range

± 1

± 11

Full range

to

to

4

11

RL = 10 kΩ

25°C

3

4.2

13

13.9

VOM +

Maximum positive peak

Full range

3

13

V

output voltage swing

RL = 2 kΩ

25°C

2.5

3.8

11.5

12.7

Full range

2.5

11.5

RL = 10 kΩ

25°C

± 2.5

± 3.5

± 12

± 13.2

VOM ±

Maximum negative peak

Full range

± 2.5

± 12

V

output voltage swing

RL = 2 kΩ

25°C

± 2.3

± 3.2

± 11

± 12

Full range

± 2.3

± 11

Large-signal differential

25°C

25

59

50

105

RL = 2 kΩ

AVD

0°C

30

65

60

129

V/mV

voltage amplification¶

70°C

20

46

30

85

ri

Input resistance

25°C

1012

1012

Ω

ci

Input capacitance

25°C

10

12

pF

Common-mode

VIC = VICRmin,

25°C

65

85

75

93

CMRR

0°C

65

84

75

92

dB

rejection ratio

VO = 0,

RS = 50 Ω

70°C

65

84

75

91

Supply-voltage rejection

25°C

75

99

75

99

RS = 50 Ω

kSVR

VO = 0,

0°C

75

98

75

98

dB

ratio ( VCC ± / VIO)

70°C

75

97

75

97

25°C

2.6

3.2

2.7

3.2

ICC

Supply current

VO = 0,

No load

0°C

2.7

3.2

2.8

3.2

mA

70°C

2.6

3.2

2.7

3.2

² Full range is 0°C to 70°C.

³This parameter is tested on a sample basis for the TL051A. For other test requirements, please contact the factory. This statement has no bearing on testing or nontesting of other parameters.

§Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

±5 V, VO = ± 2.3 V, or for VCC ± = ± 15 V, VO = ±10 V.

8	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TL05x, TL05xA, TL05xY

ENHANCED-JFET LOW-OFFSET

OPERATIONAL AMPLIFIERS

SLOS178 ± FEBRUARY 1997

TL051C and TL051AC operating characteristics at specified free-air temperature

TL051C, TL051AC

T ²

PARAMETER

TEST CONDITIONS

V

= ± 5 V

V

CC ±

= ± 15 V

UNIT

A

CC ±

MIN

TYP MAX

MIN

TYP MAX

Positive slew rate

25°C

16

13

20

SR +

Full

at unity gain³

16.4

11

22.6

RL = 2 kΩ,

CL = 100 pF,

range

V/ µs

Negative slew rate

See Figure 1

25°C

15

13

18

SR ±

Full

at unity gain³

16

11

19.3

range

25°C

55

56

tr

Rise time

0°C

54

55

70°C

63

63

ns

VI(PP) = ±10 mV,

25°C

55

57

RL = 2 kΩ,

tf

Fall time

0°C

54

56

CL = 100 pF,

70°C

62

64

See Figures 1 and 2

25°C

24%

19%

Overshoot factor

0°C

24%

19%

70°C

24%

19%

Vn

Equivalent input noise

f = 10 Hz

25°C

75

75

nV/√ Hz

voltage§

RS = 20 Ω,

f = 1 kHz

25°C

18

18

30

VN(PP)

Peak-to-peak equivalent

See Figure 3

f = 10 Hz to

25°C

4

4

µV

input noise voltage

10 kHz

Equivalent input

25°C

In

f = 1 kHz

0.01

0.01

pA/√ Hz

noise current

THD

Total harmonic distortion¶

RS = 1 kΩ,

RL = 2 kΩ,

25°C

0.003%

0.003%

f = 1 kHz

VI = 10 mV,

RL = 2 kΩ,

25°C

3

3.1

B1

Unity-gain bandwidth

0°C

3.2

3.3

MHz

CL = 25 pF,

See Figure 4

70°C

2.7

2.8

Phase margin at unity

VI = 10 mV,

RL = 2 kΩ,

25°C

59°

62°

φm

0°C

58°

62°

gain

CL = 25 pF,

See Figure 4

70°C

59°

62°

² Full range is 0°C to 70°C.

³ For VCC ± = ± 5 V, VI(PP) = ± 1 V; for VCC ± = ± 15 V, VI(PP) = ± 5 V.

§This parameter is tested on a sample basis for the TL051A. For other test requirements, please contact the factory. This statement has no bearing on testing or nontesting of other parameters.

¶ For VCC ± = ± 5 V, VOrms = 1 V; for VCC ± = ± 15 V, VOrms = 6 V.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

9

TL05x, TL05xA, TL05xY

ENHANCED-JFET LOW-OFFSET

OPERATIONAL AMPLIFIERS

SLOS178 ± FEBRUARY 1997

TL051I and TL051AI electrical characteristics at specified free-air temperature

								TL051I, TL051AI
				T ²
	PARAMETER	TEST CONDITIONS			V		= ± 5 V		V		= ± 15 V		UNIT
				A	CC ±				CC ±
					MIN	TYP		MAX	MIN		TYP	MAX
			TL051I	25°C		0.75		3.5			0.59	1.5
VIO	Input offset voltage			Full range				5.3				3.3	mV
			TL051AI	25°C		0.55		2.8			0.35	0.8
		VO = 0,		Full range				4.6				2.6
				25°C to
		VIC = 0,	TL051I				7				8
	Temperature coefficient of			85°C
		RS = 50 Ω											°
αVIO	input offset voltage³												µV/ C
			TL051AI	25°C to			8				8	25
				85°C
	Input offset voltage			25°C		0.04					0.04		µV/mo
	long-term drift§
IIO	Input offset current	VO = 0,	VIC = 0,	25°C			4	100			5	100	pA
		See Figure 5		85°C		0.06		10			0.07	10	nA
IIB	Input bias current	VO = 0,	VIC = 0,	25°C			20	200			30	200	pA
		See Figure 5		85°C			0.6	20			0.7	20	nA
					± 1	± 2.3			± 11	± 12.3
				25°C	to		to		to		to
VICR	Common-mode input				4		5.6		11		15.6		V
	voltage range				± 1				± 11
				Full range	to				to
					4				11
		RL = 10 kΩ		25°C	3		4.2		13		13.9
VOM +	Maximum positive peak			Full range	3				13				V
	output voltage swing	RL = 2 kΩ		25°C	2.5		3.8		11.5		12.7
				Full range	2.5				11.5
		RL = 10 kΩ		25°C	± 2.5	± 3.5			± 12	± 13.2
VOM ±	Maximum negative peak			Full range	± 2.5				± 12				V
	output voltage swing	RL = 2 kΩ		25°C	± 2.3	± 3.2			± 11		± 12
				Full range	± 2.3				± 11
	Large-signal differential			25°C	25		59		50		105
AVD		RL = 2 kΩ		± 40°C	30		74		60		145		V/mV
	voltage amplification¶
				85°C	20		43		30		76
ri	Input resistance			25°C		1012				1012			Ω
ci	Input capacitance			25°C			10				12		pF
	Common-mode	VIC = VICRmin,		25°C	65		85		75		93
CMRR		VO = 0,		± 40°C	65		83		75		90		dB
	rejection ratio
		RS = 50 Ω
				85°C	65		84		75		93
	Supply-voltage rejection	VO = 0,		25°C	75		99		75		99
kSVR				± 40°C	75		98		75		98		dB
	ratio ( VCC± / VIO)	RS = 50 Ω
				85°C	75		99		75		99
				25°C			2.6	3.2			2.7	3.2
ICC	Supply current	VO = 0,	No load	± 40°C			2.4	3.2			2.6	3.2	mA
				85°C			2.5	3.2			2.6	3.2

² Full range is ± 40°C to 85°C

³This parameter is tested on a sample basis for the TL051A. For other test requirements, please contact the factory. This statement has no bearing on testing or nontesting of other parameters.

§Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

±5 V, VO = ± 2.3 V, or for VCC ± = ± 15 V, VO = ±10 V.

10	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TL05x, TL05xA, TL05xY

ENHANCED-JFET LOW-OFFSET

OPERATIONAL AMPLIFIERS

SLOS178 ± FEBRUARY 1997

TL051I and TL051AI operating characteristics at specified free-air temperature

TL051I, TL051AI

T ²

PARAMETER

TEST CONDITIONS

V

CC ±

= ± 5 V

V

CC ±

= ± 15 V

UNIT

A

MIN

TYP MAX

MIN

TYP

MAX

Positive slew rate

25°C

16

13

20

SR +

Full

at unity gain³

11

RL = 2 kΩ,

CL = 100 pF,

range

V/ µs

Negative slew rate

See Figure 1

25°C

15

13

18

SR ±

Full

at unity gain³

11

range

25°C

55

56

tr

Rise time

± 40°C

52

53

85°C

64

65

ns

VI(PP) = ±10 mV,

25°C

55

57

RL = 2 kΩ,

tf

Fall time

± 40°C

51

53

CL = 100 pF,

85°C

64

65

See Figures 1 and 2

25°C

24%

19%

Overshoot factor

± 40°C

24%

19%

85°C

24%

19%

Vn

Equivalent input noise

f = 10 Hz

25°C

75

75

nV/√ Hz

voltage§

RS = 20 Ω,

f = 1 kHz

25°C

18

18

30

VN(PP)

Peak-to-peak equivalent

See Figure 3

f = 10 Hz to

25°C

4

4

µV

input noise voltage

10 kHz

Equivalent input

In

f = 1 kHz

25°C

0.01

0.01

pA/√ Hz

noise current

THD

Total harmonic distortion¶

RS = 1 kΩ,

RL = 2 kΩ,

25°C

0.003%

0.003%

f = 1 kHz

VI = 10 mV,

RL = 2 kΩ,

25°C

3

3.1

B1

Unity-gain bandwidth

± 40°C

3.5

3.6

MHz

CL = 25 pF,

See Figure 4

85°C

2.6

2.7

Phase margin at unity

VI = 10 mV,

RL = 2 kΩ,

25°C

59°

62°

φm

± 40°C

58°

61°

gain

CL = 25 pF,

See Figure 4

85°C

59°

62°

² Full range is ± 40°C to 85°C.

³ For VCC ± = ± 5 V, VI(PP) = ± 1 V; for VCC ± = ± 15 V, VI(PP) = ± 5 V.

§This parameter is tested on a sample basis for the TL051A. For other test requirements, please contact the factory. This statement has no bearing on testing or nontesting of other parameters.

¶ For VCC ± = ± 5 V, VOrms = 1 V; for VCC ± = ± 15 V, VOrms = 6 V.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

11

TL05x, TL05xA, TL05xY

ENHANCED-JFET LOW-OFFSET

OPERATIONAL AMPLIFIERS

SLOS178 ± FEBRUARY 1997

TL051M and TL051AM electrical characteristics at specified free-air temperature

TL051M, TL051AM

T ²

PARAMETER

TEST CONDITIONS

V

= ± 5 V

V

±

= ± 15 V

UNIT

A

CC ±

CC

MIN

TYP

MAX

MIN

TYP

MAX

TL051M

25 C

0.75

3.5

0.59

1.5

VIO

Input offset voltage

Full range

6.5

4.5

mV

TL051AM

25°C

0.55

2.8

0.35

0.8

VO = 0,

Full range

5.8

3.8

25°C to

VIC = 0,

TL051M

8

8

Temperature coefficient of

Ω

125°C

αVIO

RS = 50

°

input offset voltage

TL051AM

25°C to

8

8

µV/ C

125°C

Input offset voltage

25°C

0.04

0.04

µV/mo

long-term drift³

IIO

Input offset current

VO = 0,

VIC = 0,

25°C

4

100

5

100

pA

See Figure 5

125°C

1

20

2

20

nA

IIB

Input bias current

VO = 0, VIC = 0,

25°C

20

200

30

200

pA

See Figure 5

125°C

10

50

20

50

nA

± 1

± 2.3

± 11

± 12.3

25°C

to

to

to

to

VICR

Common-mode input

4

5.6

11

15.6

V

voltage range

± 1

± 11

Full range

to

to

4

11

RL = 10 kΩ

25°C

3

4.2

13

13.9

VOM +

Maximum positive peak

Full range

3

13

V

output voltage swing

RL = 2 kΩ

25°C

2.5

3.8

11.5

12.7

Full range

2.5

11.5

RL = 10 kΩ

25°C

± 2.5

± 3.5

± 12

± 13.2

VOM ±

Maximum negative peak

Full range

± 2.5

± 12

V

output voltage swing

RL = 2 kΩ

25°C

± 2.3

± 3.2

± 11

± 12

Full range

± 2.3

± 11

Large-signal differential

25°C

25

59

50

105

AVD

RL = 2 kΩ

± 55°C

30

76

60

149

V/mV

voltage amplification§

125°C

10

32

15

49

ri

Input resistance

25°C

1012

1012

Ω

ci

Input capacitance

25°C

10

12

pF

Common-mode

VIC = VICRmin,

25°C

65

85

75

93

CMRR

VO = 0,

± 55°C

65

83

75

92

dB

rejection ratio

Ω

RS = 50

125°C

65

84

75

94

Supply-voltage rejection

25°C

75

99

75

99

kSVR

VO = 0,

RS = 50 Ω

± 55°C

75

98

75

98

dB

ratio ( VCC± / VIO)

125°C

75

100

75

100

25°C

2.6

3.2

2.7

3.2

ICC

Supply current

VO = 0,

No load

± 55°C

2.3

3.2

2.4

3.2

mA

125°C

2.4

3.2

2.5

3.2

² Full range is ± 55°C to 125°C.

³Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

±5 V, VO = ± 2.3 V, or for VCC ± = ± 15 V, VO = ± 10 V.

12	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TL05x, TL05xA, TL05xY

ENHANCED-JFET LOW-OFFSET

OPERATIONAL AMPLIFIERS

SLOS178 ± FEBRUARY 1997

TL051M and TL051AM operating characteristics at specified free-air temperature

					TL051M, TL051AM
	PARAMETER	TEST CONDITIONS		TA	VCC ± = ± 5 V	VCC ± = ± 15 V		UNIT
					MIN TYP MAX	MIN	TYP MAX
SR +	Positive slew rate			25°C	16	13	20
	at unity gain²	RL = 2 kΩ,	CL = 100 pF,
								V/µ s
SR ±	Negative slew rate	See Figure 1		25°C	15	13
	at unity gain²
				25°C	55		56
tr	Rise time			± 55°C	51		52
				125°C	68		68	ns
		VI(PP) = ± 10 mV,
				25°C	55		57
		RL = 2 kΩ,
tf	Fall time			± 55°C	51		52
		CL = 100 pF,
				125°C	68		69
		See Figures 1 and 2
				25°C	24%		19%
	Overshoot factor			± 55°C	25%		19%
				125°C	25%		19%
Vn	Equivalent input noise		f = 10 Hz	25°C	75		75
								nV/√ Hz
	voltage³	RS = 20 Ω,	f = 1 kHz	25°C	18		19
VN(PP)	Peak-to-peak equivalent	See Figure 3	f = 10 Hz to	25°C	4		4	µV
	input noise voltage		10 kHz
	Equivalent input noise
In		f = 1 kHz		25°C	0.01		0.01	pA/√ Hz
	current
THD	Total harmonic distortion§	RS = 1 kΩ,	RL = 2kΩ,	25°C	0.003%		0.003%
		f = 1 kHz
		VI = 10 mV,	RL = 2 kΩ,	25°C	3		3.1
B1	Unity-gain bandwidth			± 55°C	3.6		3.7	MHz
		CL = 25 pF,	See Figure 4
				125°C	2.3		2.4
	Phase margin at unity	VI = 10 mV,	RL = 2 kΩ,	25°C	59°		62°
φm
				± 55°C	57°		61°
	gain	CL = 25 pF,	See Figure 4
				125°C	59°		62°

² For VCC ± = ± 5 V, VI(PP) = ± 1 V; for VCC ± = ± 15 V, VI(PP) = ± 5 V.

³This parameter is tested on a sample basis for the TL051A. For other test requirements, please contact the factory. This statement has no bearing on testing or nontesting of other parameters.

§ For VCC ± = ± 5 V, VOrms = 1 V; for VCC ± = ± 15 V, VOrms = 6 V.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

13

TL05x, TL05xA, TL05xY

ENHANCED-JFET LOW-OFFSET

OPERATIONAL AMPLIFIERS

SLOS178 ± FEBRUARY 1997

TL051Y electrical characteristics, TA = 25°C

					TL051Y
		PARAMETER	TEST CONDITIONS		VCC ± = ± 5 V	VCC ± = ± 15 V	UNIT
					MIN TYP MAX	MIN TYP MAX
	VIO	Input offset voltage	VO = 0,	VIC = 0,	0.75	0.59	mV
			RS = 50 Ω
	IIO	Input offset current	VO = 0,	VIC = 0,	4	5	pA
			See Figure 5
	IIB	Input bias current	VO = 0,	VIC = 0,	20	30	pA
			See Figure 5
					± 2.3	± 12.3
	VICR	Common-mode input voltage range			to	to	V
					5.6	15.6
	VOM +	Maximum positive peak output voltage	RL = 10 kΩ		4.2	13.9	V
		swing	RL = 2 kΩ		3.8	12.7
	VOM ±	Maximum negative peak output voltage	RL = 10 kΩ		± 3.5	± 13.2	V
		swing	RL = 2 kΩ		± 3.2	± 12
	AVD	Large-signal differential voltage	RL = 2 kΩ		59	105	V/mV
		amplification²
	ri	Input resistance			1012	1012	Ω
	ci	Input capacitance			10	12	pF
	CMRR	Common-mode rejection ratio	VIC = VICRmin,		85	93	dB
			VO = 0,	RS = 50 Ω
	kSVR	Supply-voltage rejection ratio	VO = 0,	RS = 50 Ω	99	99	dB
		( VCC ± / VIO)
	ICC	Supply current	VO = 0,	No load	2.6	2.7	mA

² For VCC ± = ± 5 V, VO = ± 2.3 V, or for VCC ± = ± 15 V, VO = ± 10 V.

14	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TL05x, TL05xA, TL05xY

ENHANCED-JFET LOW-OFFSET

OPERATIONAL AMPLIFIERS

SLOS178 ± FEBRUARY 1997

TL051Y operating characteristics, TA = 25°C

					TL051Y
		PARAMETER	TEST CONDITIONS		VCC ± = ± 5 V	VCC ± = ± 15 V	UNIT
					MIN TYP MAX	MIN TYP MAX
	SR +	Positive slew rate at unity gain²	RL = 2 kΩ,	CL = 100 pF,	16	20	V/ µs
		Negative slew rate at unity gain²
	SR ±		See Figure 1		15	18
	tr	Rise time	VI(PP) = ±10 mV,		55	56	ns
			RL = 2 kΩ,
	tf	Fall time			55	57
			CL = 100 pF,
		Overshoot factor			24%	19%
			See Figures 1 and 2
	Vn	Equivalent input noise voltage³		f = 10 Hz	75	75	nV/√
			RS = 20 Ω,					Hz
				f = 1 kHz	18	18
	VN(PP)	Peak-to-peak equivalent input	See Figure 3	f = 10 Hz to	4	4	µV
		noise voltage		10 kHz
	In	Equivalent input noise current	f = 1 kHz		0.01	0.01	pA/√	Hz
	THD	Total harmonic distortion§	RS = 1 kΩ,	RL = 2 kΩ,	0.003%	0.003%
			f = 1 kHz
	B1	Unity-gain bandwidth	VI = 10 mV,	RL = 2 kΩ,	3	3.1	MHz
			CL = 25 pF,	See Figure 4
	φm	Phase margin at unity gain	VI = 10 mV,	RL = 2 kΩ,	59°	62°
			CL = 25 pF,	See Figure 4

² For VCC ± = ± 5 V, VI(PP) = ± 1 V; for VCC ± = ± 15 V, VI(PP) = ± 5 V.

³This parameter is tested on a sample basis for the TL051A. For other test requirements, please contact the factory. This statement has no bearing on testing or nontesting of other parameters.

§ For VCC ± = ± 5 V, VOrms = 1 V; for VCC ± = ± 15 V, VOrms = 6 V.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

15

TL05x, TL05xA, TL05xY

ENHANCED-JFET LOW-OFFSET

OPERATIONAL AMPLIFIERS

SLOS178 ± FEBRUARY 1997

TL052C and TL052AC electrical characteristics at specified free-air temperature

TL052C, TL052AC

T ²

PARAMETER

TEST CONDITIONS

V

CC±

= ± 5 V

V

= ± 15 V

UNIT

A

CC±

MIN

TYP

MAX

MIN

TYP

MAX

TL052C

25°C

0.73

3.5

0.65

1.5

VIO

Input offset voltage

Full range

4.5

2.5

mV

VO = 0,

TL052AC

25°C

0.51

2.8

0.4

0.8

Full range

3.8

1.8

VIC = 0,

25°C to

RS = 50 Ω

TL052C

8

8

αVIO

Temperature coefficient

70°C

µV/°C

of input offset voltage³

TL052AC

25°C to

8

6

25

70°C

Input offset voltage long-

VO = 0,

VIC = 0,

25°C

0.04

0.04

µV/mo

term drift§

RS = 50 Ω

IIO

Input offset current

VO = 0,

VIC = 0,

25°C

4

100

5

100

pA

See Figure 5

70°C

0.02

1

0.025

1

nA

IIB

Input bias current

VO = 0,

VIC = 0,

25°C

20

200

30

200

pA

See Figure 5

70°C

0.15

4

0.2

4

nA

± 1

±2.3

± 11

± 12.3

25°C

to

to

to

to

VICR

Common-mode input

4

5.6

11

15.6

V

voltage range

± 1

± 11

Full range

to

to

4

11

RL = 10 kΩ

25°C

3

4.2

13

13.9

VOM +

Maximum positive peak

Full range

3

13

V

output voltage swing

RL = 2 kΩ

25°C

2.5

3.8

11.5

12.7

Full range

2.5

11.5

RL = 10 kΩ

25°C

± 2.5

± 3.5

± 12

± 13.2

VOM ±

Maximum negative peak

Full range

± 2.5

± 12

V

output voltage swing

RL = 2 kΩ

25°C

± 2.3

± 3.2

± 11

± 12

Full range

± 2.3

± 11

Large-signal differential

25°C

25

59

50

105

AVD

RL = 2 kΩ

0°C

30

65

60

129

V/mV

voltage amplification¶

70°C

20

46

30

85

ri

Input resistance

25°C

1012

1012

Ω

ci

Input capacitance

25°C

10

12

pF

Common-mode

VIC = VICRmin,

25°C

65

85

75

93

RS = 50 Ω

CMRR

0°C

65

84

75

92

dB

rejection ratio

VO = 0,

70°C

65

84

75

91

² Full range is 0°C to 70°C.

³This parameter is tested on a sample basis. For other test requirements, please contact the factory. This statement has no bearing on testing or nontesting of other parameters.

§Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

±5 V, VO = ± 2.3 V; at VCC ± = ± 15 V, VO = ± 10 V.

16	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TL05x, TL05xA, TL05xY

ENHANCED-JFET LOW-OFFSET

OPERATIONAL AMPLIFIERS

SLOS178 ± FEBRUARY 1997

TL052C and TL052AC electrical characteristics at specified free-air temperature (continued)

						TL052C, TL052AC
	PARAMETER	TEST CONDITIONS		TA	VCC± = ± 5 V			VCC± = ± 15 V			UNIT
					MIN	TYP	MAX	MIN	TYP MAX
	Supply-voltage rejection			25°C	75	99		75	99
kSVR		VO = 0,	RS = 50 Ω	0°C	75	98		75	98		dB
	ratio ( VCC ± / VIO)
				70°C	75	97		75	97
	Supply current			25°C		4.6	5.6		4.8	5.6
ICC		VO = 0,	No load	0°C		4.7	6.4		4.8	6.4	mA
	(two amplifiers)
				70°C		4.4	6.4		4.6	6.4
VO1/ VO2 Crosstalk attenuation		AVD = 100		25°C		120			120		dB

TL052C and TL052AC operating characteristics at specified free-air temperature

TL052C, TL052AC

T ²

PARAMETER

TEST CONDITIONS

V

= ± 5 V

V

= ± 15 V

UNIT

A

CC ±

CC ±

MIN

TYP MAX

MIN

TYP

MAX

SR +

Slew rate at unity gain

25°C

17.8

9

20.7

RL = 2 kΩ,

CL = 100 pF,

Full range

8

V/µs

SR ±

Negative slew rate

See Figure 1

25°C

15.4

9

17.8

at unity gain³

Full range

8

25°C

55

56

tr

Rise time

0°C

54

55

70°C

63

63

ns

VI(PP) = ± 10 mV,

25°C

55

57

RL = 2 kΩ,

tf

Fall time

0°C

54

56

CL = 100 pF,

70°C

62

64

See Figures 1 and 2

25°C

24%

19%

Overshoot factor

0°C

24%

19%

70°C

24%

19%

Equivalent input noise

f =

10 Hz

25°C

71

71

Vn

nV/√ Hz

voltage§

RS = 20 Ω,

f =

1 kHz

25°C

19

19

30

VN(PP)

Peak-to-peak equivalent

See Figure 3

f = 10 Hz t

25°C

4

4

µV

input noise current

10 kHz

Equivalent input

In

f = 1 kHz

25°C

0.01

0.01

pA/√ Hz

noise current

THD

Total harmonic distortion¶

RS = 1 kΩ,

RL = 2 kΩ,

25°C

0.003%

0.003%

f = 1 kHz

VI = 10 mV,

RL = 2 kΩ,

25°C

3

3

B1

Unity-gain bandwidth

0°C

3.2

3.2

MHz

CL = 25 pF,

See Figure 4

70°C

2.6

2.7

Phase margin at unity

VI = 10 mV,

RL = 2 kΩ,

25°C

60°

63°

φm

0°C

59°

63°

gain

CL = 25 pF,

See Figure 4

70°C

60°

63°

² Full range is 0°C to 70°C.

³ For VCC ± = ± 5 V, VI(PP) = ± 1 V; for VCC ± = ± 15 V, VI(PP) = ± 5 V.

§This parameter is tested on a sample basis. For other test requirements, please contact the factory. This statement has no bearing on testing or nontesting of other parameters.

¶ For VCC ± = ± 5 V, VO(RMS) = 1 V; for VCC ± = ± 15 V, VO(RMS) = 6 V.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

17

TL05x, TL05xA, TL05xY

ENHANCED-JFET LOW-OFFSET

OPERATIONAL AMPLIFIERS

SLOS178 ± FEBRUARY 1997

TL052I and TL052AI electrical characteristics at specified free-air temperature

TL052I, TL052AI

T ²

PARAMETER

TEST CONDITIONS

V

CC±

= ± 5 V

V

= ± 15 V

UNIT

A

CC±

MIN

TYP

MAX

MIN

TYP

MAX

TL052I

25°C

0.73

3.5

0.65

1.5

VIO

Input offset voltage

Full range

5.3

3.3

mV

VO = 0,

TL052AI

25°C

0.51

2.8

0.4

0.8

Full range

4.6

2.6

VIC = 0,

25°C to

RS = 50 Ω

TL052I

7

6

85°C

αVIO

Temperature coefficient³

µV/°C

TL052AI

25°C to

6

6

25

85°C

Input offset voltage long-

VO = 0,

VIC = 0,

25°C

0.04

0.04

µV/mo

term drift§

RS = 50 Ω

IIO

Input offset current

VO = 0,

VIC = 0,

25°C

4

100

5

100

pA

See Figure 5

85°C

0.06

10

0.07

10

nA

IIB

Input bias current

VO = 0,

VIC = 0,

25°C

20

200

30

200

pA

See Figure 5

85°C

0.6

20

0.7

20

nA

± 1

±2.3

± 11

± 12.3

25°C

to

to

to

to

VICR

Common-mode input

4

5.6

11

15.6

V

voltage range

± 1

± 11

Full range

to

to

4

11

RL = 10 kΩ

25°C

3

4.2

13

13.9

VOM +

Maximum positive peak

Full range

3

13

V

output voltage swing

RL = 2 kΩ

25°C

2.5

3.8

11.5

12.7

Full range

2.5

11.5

RL = 10 kΩ

25°C

± 2.5

± 3.5

± 12

± 13.2

VOM ±

Maximum negative peak

Full range

± 2.5

± 12

V

output voltage swing

RL = 2 kΩ

25°C

± 2.3

± 3.2

± 11

± 12

Full range

± 2.3

± 11

Large-signal differential

25°C

25

59

50

105

RL = 2 kΩ

AVD

± 40°C

30

74

60

145

V/mV

voltage amplification¶

85°C

20

43

30

76

ri

Input resistance

25°C

1012

1012

Ω

ci

Input capacitance

25°C

10

12

pF

Common-mode

VIC = VICRmin,

25°C

65

85

75

93

CMRR

RS = 50 Ω

± 40°C

65

83

75

90

dB

rejection ratio

VO = 0,

85°C

65

84

75

93

² Full range is ± 40°C to 85°C.

³ This parameter is tested on a sample basis. For other test requirements, please contact the factory. This statement has no bearing on testing or nontesting of other parameters

§ Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated to TA = 25 °C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

¶ At VCC ± = ± 5 V, VO = ± 2.3 V; at VCC ± = ± 15 V, VO = ± 10 V.

18	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TL05x, TL05xA, TL05xY

ENHANCED-JFET LOW-OFFSET

OPERATIONAL AMPLIFIERS

SLOS178 ± FEBRUARY 1997

TL052I and TL052AI electrical characteristics at specified free-air temperature (continued)

							TL052I, TL052AI
	PARAMETER	TEST CONDITIONS		TA	VCC± = ± 5 V			VCC± = ± 15 V			UNIT
					MIN	TYP	MAX	MIN	TYP MAX
	Supply-voltage rejection			25°C	75	99		75	99
kSVR		VO = 0,	RS = 50 Ω	± 40°C	75	98		75	98		dB
	ratio ( VCC± / VIO)
				85°C	75	99		75	99
	Supply current			25°C		4.6	5.6		4.8	5.6
ICC		VO = 0,	No load	± 40°C		4.5	6.4		4.7	6.4	mA
	(two amplifiers)
				85°C		4.4	6.4		4.6	6.4
VO1/ VO2 Crosstalk attenuation		AVD = 100		25°C		120			120		dB

TL052I and TL052AI operating characteristics at specified free-air temperature

TL052I, TL052AI

T ²

PARAMETER

TEST CONDITIONS

V

= ± 5 V

V

= ± 15 V

UNIT

A

CC ±

CC ±

MIN

TYP MAX

MIN

TYP

MAX

SR +

Slew rate at unity gain³

25°C

17.8

9

20.7

RL = 2 kΩ,

CL = 100 pF,

Full range

8

V/µs

See Figure 1

SR ±

Negative slew rate at

25°C

15.4

9

17.8

unity gain³

Full range

8

25°C

55

56

tr

Rise time

± 40°C

52

53

85°C

64

65

ns

VI(PP) = ± 10 mV,

25°C

55

57

± 40°C

tf

Fall time

RL = 2 kΩ,

CL = 100 pF,

51

53

See Figures 1 and 2

85°C

64

65

25°C

24%

19%

Overshoot factor

± 40°C

24%

19%

85°C

24%

19%

Vn

Equivalent input noise

f =

10 Hz

25°C

71

71

voltage§

RS = 20 Ω,

f =

1 kHz

25°C

19

19

30

VN(PP)

Peak-to-peak equivalent

See Figure 3

f =

10 Hz to

25°C

4

4

µV

input noise current

10 kHz

Equivalent input noise

In

f = 1 kHz

25°C

0.01

0.01

pA/√ Hz

current

THD

Total harmonic distortion¶

RS = 1 kΩ,

RL = 2 kΩ,

25°C

0.003%

0.003%

f = 1 kHz

VI = 10 mV,

RL = 2 kΩ,

25°C

3

3

B1

Unity-gain bandwidth

± 40°C

3.5

3.6

MHz

CL = 25 pF,

See Figure 4

85°C

2.5

2.6

Phase margin at unity

VI = 10 mV,

RL = 2 kΩ,

25°C

60°

63°

φm

± 40°C

58°

61°

gain

CL = 25 pF,

See Figure 4

85°C

60°

63°

² Full range is ± 40°C to 85°C.

³ For VCC ± = ± 5 V, VI(PP) = ± 1 V; for VCC ± = ± 15 V, VI(PP) = ± 5 V.

§This parameter is tested on a sample basis. For other test requirements, please contact the factory. This statement has no bearing on testing or nontesting of other parameters.

¶ For VCC ± = ± 5 V, VO(RMS) = 1 V; for VCC ± = ± 15 V, VO(RMS) = 6 V.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

19

TL05x, TL05xA, TL05xY

ENHANCED-JFET LOW-OFFSET

OPERATIONAL AMPLIFIERS

SLOS178 ± FEBRUARY 1997

TL052M and TL052AM electrical characteristics at specified free-air temperature

TL052M, TL052AM

T ²

PARAMETER

TEST CONDITIONS

V

= ± 5 V

V

= ± 15 V

UNIT

A

CC ±

CC ±

MIN

TYP

MAX

MIN

TYP

MAX

TL052M

25°C

0.73

3.5

0.65

1.5

VIO

Input offset voltage

Full range

6.5

4.5

mV

VO = 0,

TL052AM

25°C

0.51

2.8

0.4

0.8

Full range

5.8

3.8

VIC = 0,

25°C to

RS = 50 Ω

TL052M

10

9

Temperature coefficient

125°C

αVIO

µV/°C

of input offset voltage

TL052AM

25°C to

9

8

125°C

Input offset voltage long-

VO = 0,

VIC = 0,

25°C

0.04

0.04

µV/mo

term drift³

RS = 50 Ω

IIO

Input offset current

VO = 0,

VIC = 0,

25°C

4

100

5

100

pA

See Figure 5

125°C

1

20

2

20

nA

IIB

Input bias current

VO = 0,

VIC = 0,

25°C

20

200

30

200

pA

See Figure 5

125°C

10

50

20

50

nA

± 1

±2.3

± 11

± 12.3

25°C

to

to

to

to

VICR

Common-mode input

4

5.6

11

15.6

V

voltage range

± 1

± 11

Full range

to

to

4

11

RL = 10 kΩ

25°C

3

4.2

13

13.9

VOM +

Maximum positive peak

Full range

3

13

V

output voltage swing

RL = 2 kΩ

25°C

2.5

3.8

11.5

12.7

Full range

2.5

11.5

RL = 10 kΩ

25°C

± 2.5

± 3.5

± 12

± 13.2

VOM ±

Maximum negative peak

Full range

± 2.5

± 12

V

output voltage swing

RL = 2 kΩ

25°C

± 2.3

± 3.2

± 11

± 12

Full range

± 2.3

± 11

Large-signal differential

25°C

25

59

50

105

AVD

RL = 2 kΩ

± 55°C

30

76

60

149

V/mV

voltage amplification§

125°C

10

32

15

49

ri

Input resistance

25°C

1012

1012

Ω

ci

Input capacitance

25°C

10

12

pF

Common-mode

VIC = VICRmin,

25°C

65

85

75

93

CMRR

VO = 0,

± 55°C

65

83

75

92

dB

rejection ratio

RS = 50 Ω

125°C

65

84

75

94

Supply-voltage rejection

25°C

75

99

75

99

kSVR

VO = 0,

RS = 50 Ω

± 55°C

75

98

75

98

dB

ratio ( VCC± / VIO)

125°C

75

100

75

100

Supply current

25°C

4.6

5.6

4.8

5.6

ICC

VO = 0,

No load

± 55°C

4.4

6.4

4.5

6.4

mA

(two amplifiers)

125°C

4.2

6.4

4.4

6.4

VO1/ VO2

Crosstalk attenuation

AVD = 100

25°C

120

120

dB

² Full range is ± 55°C to 125°C.

³Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

±5 V, VO = ± 2.3 V; at VCC ± = ± 15 V, VO = ± 10 V.

20	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265