Texas Instruments TLC374CN, TLC374CDR, TLC374CDBR, TLC374CD, TLC374CDB Datasheet

LinCMOS	TLC374, TLC374Q, TLC374Y
	QUADRUPLE DIFFERENTIAL COMPARATORS
	SLCS118C ± NOVEMBER 1983 ± REVISED MARCH 1999
D Singleor Dual-Supply Operation	D, J, N, OR PW PACKAGE
D Wide Range of Supply Voltages			(TOP VIEW)
2 V to 18 V	1OUT					3OUT
			1	14
D Very Low Supply Current Drain 0.3 mA Typ
at 5 V	2OUT		2	13		4OUT
D Fast Response Time . . . 200 ns Typ for	VDD		3	12		GND
	2IN ±		4	11		4IN +
TTL-Level Input Step
	2IN +			10		4IN ±
D Built-In ESD Protection			5
	1IN ±			9		3IN +
			6
D High Input Impedance . . . 1012 Ω Typ
	1IN +			8		3IN ±
			7

DExtremely Low Input Bias Current 5 pA Typ

	D Ultrastable Low Input Offset Voltage	FK PACKAGE
		(TOP VIEW)

D Input Offset Voltage Change at Worst-Case			2OUT	1OUT NC 3OUT 4OUT
Input Conditions Typically 0.23 µV/Month,
Including the First 30 Days
D Common-Mode Input Voltage Range		VDD	3	2	1	20 19	GND
Includes Ground			4			18
D Outputs Compatible With TTL, MOS, and		NC	5			17	NC
		2IN ±	6			16	4IN +
CMOS
		NC	7			15	NC
D Pin-Compatible With LM339
		2IN +	8			14	4IN ±
description			9	10 11 12 13
			1IN±	1IN+	NC	3IN± 3IN+
These quadruple differential comparators are
fabricated using LinCMOS	technology and	NC ± No internal connection
consist of four independent voltage comparators		symbol (each comparator)
designed to operate from a single power supply.
Operation from dual supplies is also possible if the
difference between the two supplies is 2 V to 18 V.		IN +
Each device features extremely high input							OUT
impedance (typically greater than 1012 Ω),		IN ±
allowing direct interfacing with high-impedance
sources. The outputs are n-channel open-drain
configurations and can be connected to achieve
positive-logic wired-AND relationships.

The TLC374 has internal electrostatic discharge (ESD) protection circuits and has been classified with a 1000-V ESD rating using human body model testing. However, care should be exercised in handling this device as exposure to ESD may result in degradation of the device parametric performance.

The TLC374C is characterized for operation from 0°C to 70°C. The TLC374I is characterized for operation from ±40° to 85°C. The TLC374M is characterized for operation over full military temperature range of ±55°C to 125°C. The TLC374Q is characterized for operation from ±40°C to 125°C.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

LinCMOS is a trademark of Texas Instruments Incorporated.

PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.

Copyright 1999, Texas Instruments Incorporated

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

1

TLC374, TLC374Q, TLC374Y
LinCMOS	QUADRUPLE DIFFERENTIAL COMPARATORS
SLCS118C ± NOVEMBER 1983 ± REVISED MARCH 1999
				AVAILABLE OPTIONS
		VIO max		PACKAGED DEVICES				CHIP
TA			SMALL OUTLINE	CHIP CARRIER	CERAMIC DIP	PLASTIC DIP	TSSOP	FORM
		AT 25°C
			(D)	(FK)	(J)	(N)	(PW)	(Y)
0°C to 70°C		5 mV	TLC374CD	Ð	Ð	TLC374CN	TLC374CPW	TLC374Y
± 40°C to 85°C		5 mV	TLC374ID	Ð	Ð	TLC374IN	Ð	Ð
± 55°C to 125°C		5 mV	TLC374MD	TLC374MFK	TLC374MJ	TLC374MN	Ð	Ð
± 40°C to 125°C		5 mV	TLC374QD	Ð	Ð	TLC374QN	Ð	Ð

The D packages are available taped and reeled. Add R suffix to device type (e.g., TLC374CDR).

equivalent schematic (each comparator)

Common to All Channels

VDD
	OUT
GND
IN +	IN ±

2	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TLC374, TLC374Q, TLC374Y

LinCMOS QUADRUPLE DIFFERENTIAL COMPARATORS

SLCS118C ± NOVEMBER 1983 ± REVISED MARCH 1999

TLC374Y chip information

This chip, when properly assembled, displays characteristics similar to the TLC374C. Thermal compression or ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive epoxy or a gold-silicon preform.

BONDING PAD ASSIGNMENTS

					(13)	(12)		(11)	(10)	(9)
					(14)
										(8)
65										(7)
					(1)
					(2)	(3)		(4)	(5)	(6)
						90

						VDD
	(7)						(3)
1IN +					+
								(1)			1OUT
1IN ±		(6)			±
								(5)
					+						2IN +
2OUT		(2)
								(4)
					±						2IN ±
3IN +		(9)
					+
								(14)			3OUT
3IN ±		(8)			±
								(11)
					+
4OUT		(13)									4IN +
							±	(10)			4IN ±
							(12)
						GND

CHIP THICKNESS: 15 TYPICAL BONDING PADS: 4 × 4 MINIMUM TJMAX = 150°C

TOLERANCES ARE ± 10%

ALL DIMENSIONS ARE IN MILS.

PIN (4) IS INTERNALLY CONNECTED TO BACKSIDE OF CHIP.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

3

TLC374, TLC374Q, TLC374Y

LinCMOS QUADRUPLE DIFFERENTIAL COMPARATORS

SLCS118C ± NOVEMBER 1983 ± REVISED MARCH 1999

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)²

Supply voltage, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . .	. . . . . . . . . . 18	V
Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	. . . . . . . . ± 18	V
Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	. . . . . . . . . VDD
Input voltage range, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	±0.3 V to 18	V
Output voltage, VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	. . . . . . . . . 18	V
Input current, II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	. . . . . . . ± 5 mA
Output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	. . . . . . . 20 mA
Duration of output short circuit to ground (see Note 3) . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	. . . . . unlimited
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	See Dissipation Rating Table
Operating free-air temperature range, TA: TLC374C . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	. . 0°C to 70°C
TLC374I . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	±40°C to 85°C
TLC374M . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . .	±55°C to 125°C
TLC374Q . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . .	±40°C to 125°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . .	±65°C to 150°C
Case temperature range for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	. . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: D, N, or PW package . . . . .		. . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: J package . .	. . . . . . . . . . . .	. . . . . . . 300°C

²Stresses beyond those listed under ªabsolute maximum ratingsº may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under ªrecommended operating conditionsº is not

implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values except differential voltages are with respect to network ground.

2.Differential voltages are at IN+ with respect to IN ±.

3.Short circuits from outputs to VDD can cause excessive heating and eventual device destruction.

DISSIPATION RATING TABLE

	PACKAGE	TA ≤ 25°C	DERATING	DERATE	TA = 70°C	TA = 85°C	TA = 125°C
		POWER RATING	FACTOR	ABOVE TA	POWER RATING	POWER RATING	POWER RATING
	D	500 mW	7.6 mW/°C	84°C	500 mW	494 mW	190 mW
	FK	500 mW	11.0 mW/°C	104°C	500 mW	500 mW	269 mW
	J	500 mW	11.0 mW/°C	104°C	500 mW	500 mW	269 mW
	N	500 mW	9.2 mW/°C	95°C	500 mW	500 mW	224 mW
	PW	700 mW	5.6 mW/°C	Ð	448 mW	Ð	Ð

recommended operating conditions

			TLC374C		TLC374I		TLC374M		TLC374Q		UNIT
			MIN	MAX	MIN	MAX	MIN	MAX	MIN	MAX
	Supply voltage, VDD		3	16	3	16	4	16	3	16	V
	Common-mode input voltage, VIC	VDD = 5 V	0	3.5	0	3.5	0	3.5	0	3.5	V
		VDD = 10 V	0	8.5	0	8.5	0	8.5	0	8.5
	Operating free-air temperature, TA		0	70	± 40	85	± 55	125	± 40	125	°C

4	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

75265 TEXAS DALLAS, •655303 BOX OFFICE POST

5

electrical characteristics at specified free-air temperature, VDD = 5 V

PARAMETER

TEST CONDITIONS

T ²

TLC374C

TLC374I

TLC374M

UNIT

A

MIN

TYP

MAX

MIN

TYP

MAX

MIN

TYP

MAX

VIO

Input offset voltage

VIC = VICRmin,

See Note 4

25°C

1

5

1

5

1

5

mV

Full range

6.5

7

10

IIO

Input offset current

25°C

1

1

1

pA

MAX

0.3

1

10

nA

IIB

Input bias current

25°C

5

5

5

pA

MAX

0.6

2

20

nA

25°C

0 to

0 to

0 to

Common-mode input

VDD ± 1

VDD ± 1

VDD ± 1

VICR

V

voltage range

Full range

0 to

0 to

0 to

VDD ± 1.5

VDD ± 1.5

VDD ± 1.5

IOH

High-level output current

VID = 1 V

VOH = 5 V

25°C

0.1

0.1

0.1

nA

VOH = 15 V

Full range

1

1

1

µA

VOL

Low-level output voltage

VID = ±1 V,

IOL = 4 mA

25°C

150

400

150

400

150

400

mV

Full range

700

700

700

IOL

Low-level output current

VID = ±1 V,

VOL = 1.5 V

25°C

6

16

6

16

6

16

mA

IDD

Supply current

VID = 1 V,

No load

25°C

300

600

300

600

300

600

µA

(four comparators)

Full range

800

800

800

² All characteristics are measured with zero common-mode input voltage unless otherwise noted. Full range is 0°C to 70°C for TLC374C, ± 40°C to 85°C for TLC374I, and ± 55°C to 125°C for the TLC374M, and ± 40°C to 125°C for TLC374Q. MAX is 70°C for TLC374C, 85°C TLC374I, and 125°C for the TLC374M, and 125°C for TLC374Q. IMPORTANT: See Parameter Measurement Information.

NOTE 4: The offset voltage limits given are the maximum values required to drive the output above 4 V or below 400 mV with a 10-kΩ resistor between the output and VDD. They can be verified by applying the limit value to the input and checking for the appropriate output state.

switching characteristics, VDD = 5 V, TA = 25°C

					TLC374C, TLC374I
	PARAMETER		TEST CONDITIONS		TLC374M, TLC374Q	UNIT
					MIN TYP MAX
Response time		RL connected to 5 V through 5.1 kΩ,		100-mV input step with 5-mV overdrive	650	ns
		CL = 15 pF ³ ,	See Note 5	TTL-level input step	200

³ CL includes probe and jig capacitance.

NOTE 5: The response time specified is the interval between the input step function and the instant when the output crosses 1.4 V.

	LinCMOS
1999 MARCH REVISED ± 1983 NOVEMBER ± SLCS118C	TLC374Y TLC374Q, TLC374, COMPARATORS DIFFERENTIAL QUADRUPLE

TLC374, TLC374Q, TLC374Y

LinCMOS QUADRUPLE DIFFERENTIAL COMPARATORS

SLCS118C ± NOVEMBER 1983 ± REVISED MARCH 1999

electrical characteristics at specified free-air temperature, VDD = 5 V, TA = 25°C (unless otherwise noted)

	PARAMETER	TEST CONDITIONS			TLC374Y		UNIT
				MIN	TYP	MAX
VIO	Input offset voltage	VIC = VICRmin,	See Note 4		1	5	mV
IIO	Input offset current				1		pA
IIB	Input bias current				5		pA
VICR	Common-mode input voltage range			0 to VDD ± 1			V
IOH	High-level output current	VID = 1 V,	VOH = 5 V		0.1		nA
VOL	Low-level output voltage	VID = ± 1 V,	IOL = 4 mA		150	400	mV
IOL	Low-level output current	VID = ± 1 V,	VOL = 1.5 mV	6	16		mA
IDD	Supply current (four comparators)	VID =1 V,	No load		300	600	µA

NOTE 4: The offset voltage limits given are the maximum values required to drive the output above 4 V or below 400 mV with a 10-kΩ resistor between the output and VDD. They can be verified by applying the limit value to the input and checking for the appropriate output state.

switching characteristics, VDD = 5 V, TA = 25°C

PARAMETER		TEST CONDITIONS			TLC374Y	UNIT
				MIN	TYP MAX
Response time	RL connected to 5 V through 5.1 kΩ,		100-mV input step with 5-mV overdrive		650	ns
	CL = 15 pF ² ,	See Note 5	TTL-level input step		200

² CL includes probe and jig capacitance.

NOTE 4: The response time specified is the interval between the input step function and the instant when the output crosses 1.4 V.

6	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265