Texas Instruments TLC25L2CPWR, TLC25L2CPW, TLC25L2CPSR, TLC25L2CPS, TLC25L2CP Datasheet

TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS

SLOS002G ± JUNE 1983 ± REVISED AUGUST 1996

D D D

D D

A-Suffix Versions Offer 5-mV VIO

B-Suffix Versions Offer 2-mV VIO

Wide Range of Supply Voltages

1.4 V to 16 V

True Single-Supply Operation

Common-Mode Input Voltage Includes the

Negative Rail

D OR P PACKAGE

(TOP VIEW)

1OUT		1	8		VDD
1IN ±
		2	7		2OUT
1IN +		3	6		2IN ±
VDD ±/GND		4	5		2IN +

. . .D Low Noise	30 nV/√	Hz	Typ at f = 1 kHz
(High-Bias Versions)				symbol (each amplifier)
description				IN +		+
The TLC252, TLC25L2, and TLC25M2 are								OUT
low-cost, low-power dual operational amplifiers				IN ±		±
designed to operate with single or dual supplies.
These devices	utilize the Texas Instruments

silicon gate LinCMOS process, giving them stable input offset voltages that are available in selected grades of 2, 5, or 10 mV maximum, very high input impedances, and extremely low input offset and bias currents. Because the input common-mode range extends to the negative rail and the power consumption is extremely low, this series is ideally suited for battery-powered or energy-conserving applications. The series offers operation down to a 1.4-V supply, is stable at unity gain, and has excellent noise characteristics.

These devices have internal electrostatic-discharge (ESD) protection circuits that prevent catastrophic failures at voltages up to 2000 V as tested under MIL-STD-883C, Method 3015.1. However, care should be exercised in handling these devices as exposure to ESD may result in a degradation of the device parametric performance.

AVAILABLE OPTIONS

		VIOmax	PACKAGED DEVICES		CHIP FORM
	TA
			SMALL OUTLINE	PLASTIC DIP
		AT 25°C			(Y)
			(D)	(P)
		10 mV	TLC252CD	TLC252CP	TLC252Y
		5 mV	TLC252ACD	TLC252ACP	Ð
		2 mV	TLC252BCD	TLC252BCP	Ð
	0°C to 70°C	10 mV	TLC25L2CD	TLC25L2CP	TLC25L2Y
		5 mV	TLC25L2ACD	TLC25L2ACP	Ð
		2 mV	TLC25L2BCD	TLC25L2BCP	Ð
		10 mV	TLC25M2CD	TLC25M2CP	TLC25M2Y
		5 mV	TLC25M2ACD	TLC25M2ACP	Ð
		2 mV	TLC25M2BCD	TLC25M2BCP	Ð

The D package is available taped and reeled. Add the suffix R to the device type (e.g., TLC252CDR). Chips are tested at 25°C.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

LinCMOS is a trademark of Texas Instruments Incorporated.

PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.

Copyright 1996, Texas Instruments Incorporated

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

1

TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y

LinCMOS DUAL OPERATIONAL AMPLIFIERS

SLOS002G ± JUNE 1983 ± REVISED AUGUST 1996

description (continued)

Because of the extremely high input impedance and low input bias and offset currents, applications for the TLC252/25_2 series include many areas that have previously been limited to BIFET and NFET product types. Any circuit using high-impedance elements and requiring small offset errors is a good candidate for cost-effective use of these devices. Many features associated with bipolar technology are available with LinCMOS operational amplifiers without the power penalties of traditional bipolar devices. General applications such as transducer interfacing, analog calculations, amplifier blocks, active filters, and signal buffering are all easily designed with the TLC252/25_2 series devices. Remote and inaccessible equipment applications are possible using their low-voltage and low-power capabilities. The TLC252/25_2 series is well suited to solve the difficult problems associated with single-battery and solar-cell-powered applications. This series includes devices that are characterized for the commercial temperature range and are available in 8-pin plastic dip and the small-outline package. The device is also available in chip form.

The TLC252/25_2 series is characterized for operation from 0°C to 70°C.

	equivalent schematic (each amplifier)
	VDD	8
		3, 5	ESD-
	IN +		Protective
			Network
		2, 6	ESD-
	IN ±		Protective
			Network
			1, 7

OUT

4

VDD ± /GND

2	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS

SLOS002G ± JUNE 1983 ± REVISED AUGUST 1996

TLC252Y, TLC25L2Y, and TLC25M2Y chip information

These chips, properly assembled, display characteristics similar to the TLC252/25_2. Thermal compression or ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive epoxy or a gold-silicon preform.

BONDING PAD ASSIGNMENTS

								(5)	(4)		(3)
								(6)			(2)
				60				(7)	(8)		(1)
									73

				VDD
(3)						(8)
			+
1IN +								(1)		1OUT
(2)			±
1IN ±								(5)
		+								2IN +
(7)
2OUT						±		(6)		2IN ±
						(4)
		VDD ± /GND

CHIP THICKNESS: 15 TYPICAL BONDING PADS: 4 × 4 MINIMUM TJMAX = 150°C

TOLERANCES ARE ± 10%.

ALL DIMENSIONS ARE IN MILS.

PIN (4) IS INTERNALLY CONNECTED TO BACKSIDE OF CHIP.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

3

TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y

LinCMOS DUAL OPERATIONAL AMPLIFIERS

SLOS002G ± JUNE 1983 ± REVISED AUGUST 1996

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)²

Supply voltage, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . . . . . . . . . . . 18	V
Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . . . . . . . . . . ± 18	V
Input voltage range, VI (any input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . . ±0.3 V to 18	V
Duration of short circuit at (or below) 25°C free-air temperature (see Note 3) .	. . . . . . . . . . . . . . . . . unlimited
Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	See Dissipation Rating Table
Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . . . . 0°C to 70°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . ±65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . .	. . . . . . . . . . . . . . . . . . . 260°C

²Stresses beyond those listed under ªabsolute maximum ratingsº may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under ªrecommended operating conditionsº is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

NOTES: 1. All voltage values, except differential voltages, are with respect to VDD ±/GND.

2.Differential voltages are at IN+, with respect to IN ±.

3.The output may be shorted to either supply. Temperature and/or supply voltages must be limited to ensure the maximum dissipation rating is not exceeded.

		DISSIPATION RATING TABLE
	PACKAGE	TA ≤ 25°C	DERATING FACTOR	TA = 70°C
		POWER RATING	ABOVE TA = 25°C	POWER RATING
	D	725 mW	5.8 mW/°C	464 mW
	P	1000 mW	8.0 mW/°C	640 mW

recommended operating conditions

			MIN	MAX	UNIT
	Supply voltage, VDD		1.4	16	V
		VDD = 1.4 V	0	0.2
	Common-mode input voltage, VIC	VDD = 5 V	± 0.2	4	V
		VDD = 10 V	± 0.2	9
		VDD = 16 V	± 0.2	14
	Operating free-air temperature, TA		0	70	°C

4	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS

SLOS002G ± JUNE 1983 ± REVISED AUGUST 1996

electrical characteristics at specified free-air temperature, VDD = 1.4 V (unless otherwise noted)

PARAMETER

TEST CONDITIONS²

TLC252_C

TLC25L2_C

TLC25M2_C

UNIT

MIN

TYP

MAX

MIN

TYP

MAX

MIN

TYP

MAX

25°C

10

10

10

TLC25_2C

0°C to

12

12

12

70°C

Input

VO

= 0.2 V,

25°C

5

5

5

V

offset

TLC25_2AC

°

mV

IO

voltage

RS

= 50 Ω

0 C to

6.5

6.5

6.5

°

70 C

25°C

2

2

2

TLC25_2BC

0°C to

3

3

3

70°C

Average temperature

25°C

αVIO

coefficient of input

to

1

1

1

μV/°C

offset voltage

70°C

25°C

1

1

1

I

Input offset current

V

= 0.2 V

pA

°

IO

O

0 C to

300

300

300

70°C

25°C

1

1

1

I

Input bias current

V

= 0.2 V

pA

°

IB

O

0 C to

600

600

600

70°C

VICR

Common-mode input

25°C

0 to

0 to

0 to

V

voltage range

0.2

0.2

0.2

VOM

Peak output voltage

VID = 100 mV

25°C

450

700

450

700

450

700

mV

swing³

Large-signal

VO

= 100 to 300 mV,

AVD

differential voltage

25°C

10

20

20

V/mV

RS

= 50 Ω

amplification

CMRR

Common-mode

VO

= 0.2 V,

25°C

60

77

60

77

60

77

dB

rejection ratio

VIC = VICRmin

IDD

Supply current

VO

= 0.2 V,

25°C

300

375

25

34

200

250

μA

No load

²All characteristics are measured under open-loop conditions with zero common-mode input voltage unless otherwise specified. Unless otherwise

noted, an output load resistor is connected from the output to ground and has the following value: for low bias RL = 1 MΩ, for medium bias RL = 100 kΩ, and for high bias RL = 10 kΩ.

³The output swings to the potential of VDD ±/GND.

operating characteristics, VDD = 1.4 V, TA = 25°C

	PARAMETER	TEST CONDITIONS		TLC252_C	TLC25L2_C	TLC25M2_C		UNIT
			MIN	TYP MAX	MIN TYP MAX	MIN TYP	MAX
		AV = 40 dB,
B1	Unity-gain bandwidth	CL = 10 pF,		12	12	12		kHz
		RS = 50 Ω
SR	Slew rate at unity gain	See Figure 1		0.1	0.001	0.01		V/μs
	Overshoot factor	See Figure 1		30%	35%	35%

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

5

TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y

LinCMOS DUAL OPERATIONAL AMPLIFIERS

SLOS002G ± JUNE 1983 ± REVISED AUGUST 1996

electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)

						TLC252C, TLC252AC,
	PARAMETER		TEST CONDITIONS		T ²	TLC252BC			UNIT
					A
						MIN	TYP	MAX
		TLC252C	VO = 1.4 V,	VIC = 0,	25°C		1.1	10
			RS = 50 Ω,	RL = 10 kΩ	Full range			12
VIO	Input offset voltage	TLC252AC	VO = 1.4 V,	VIC = 0,	25°C		0.9	5	mV
			RS = 50 Ω,	RL = 10 kΩ	Full range			6.5
		TLC252BC	VO = 1.4 V,	VIC = 0,	25°C		0.23	2
			RS = 50 Ω,	RL = 10 kΩ	Full range			3
αVIO	Average temperature coefficient of				25°C to 70°C		1.8		μV/°C
	input offset voltage
IIO	Input offset current (see Note 4)		VO = 2.5 V,	VIC = 2.5 V	25°C		0.1		pA
					70°C		7	300
IIB	Input bias current (see Note 4)		VO = 2.5 V,	VIC = 2.5 V	25°C		0.6		pA
					70°C		40	600
						± 0.2	± 0.3
					25°C	to	to		V
VICR	Common-mode input voltage					4	4.2
	range (see Note 5)					± 0.2
					Full range	to			V
						3.5
					25°C	3.2	3.8
				RL = 10 kΩ
VOH	High-level output voltage		VID = 100 mV,		0°C	3	3.8		V
					70°C	3	3.8
					25°C		0	50
VOL	Low-level output voltage		VID = ± 100 mV,	IOL = 0	0°C		0	50	mV
					70°C		0	50
	Large-signal differential voltage				25°C	5	23
				RL = 10 kΩ
AVD			VO = 0.25 V to 2 V,		0°C	4	27		V/mV
	amplification
					70°C	4	20
					25°C	65	80
CMRR	Common-mode rejection ratio		VIC = VICRmin		0°C	60	84		dB
					70°C	60	85
	Supply-voltage rejection ratio				25°C	65	95
kSVR			VDD = 5 V to 10 V,	VO = 1.4 V	0°C	60	94		dB
	( VDD / VDD)
					70°C	60	96
			VO = 2.5 V,	VIC = 2.5 V,	25°C		1.4	3.2
IDD	Supply current (two amplifiers)				0°C		1.6	3.6	mA
			No load
					70°C		1.2	2.6

² Full range is 0°C to 70°C.

NOTES: 4. The typical values of input bias current and input offset current below 5 pA were determined mathematically. 5. This range also applies to each input individually.

6	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TLC252, TLC252A, TLC252B, TLC252Y, TLC25L2, TLC25L2A, TLC25L2B TLC25L2Y, TLC25M2, TLC25M2A, TLC25M2B, TLC25M2Y LinCMOS DUAL OPERATIONAL AMPLIFIERS

SLOS002G ± JUNE 1983 ± REVISED AUGUST 1996

electrical characteristics at specified free-air temperature, VDD = 10 V (unless otherwise noted)

						TLC252C, TLC252AC,
	PARAMETER		TEST CONDITIONS		T ²	TLC252BC			UNIT
					A
						MIN	TYP	MAX
		TLC252C	VO = 1.4 V,	VIC = 0,	25°C		1.1	10
			RS = 50 Ω,	RL = 10 kΩ	Full range			12
VIO	Input offset voltage	TLC252AC	VO = 1.4 V,	VIC = 0,	25°C		0.9	5	mV
			RS = 50 Ω,	RL = 10 kΩ	Full range			6.5
		TLC252BC	VO = 1.4 V,	VIC = 0,	25°C		0.29	2
			RS = 50 Ω,	RL = 10 kΩ	Full range			3
αVIO	Average temperature coefficient of input				25°C to 70°C		2		μV/°C
	offset voltage
IIO	Input offset current (see Note 4)		VO = 2.5 V,	VIC = 2.5 V	25°C		0.1		pA
					70°C		7	300
IIB	Input bias current (see Note 4)		VO = 2.5 V,	VIC = 2.5 V	25°C		0.6		pA
					70°C		50	600
						± 0.2	± 0.3
					25°C	to	to		V
VICR	Common-mode input voltage					9	9.2
	range (see Note 5)					± 0.2
					Full range	to			V
						8.5
					25°C	8	8.5
				RL = 10 kΩ
VOH	High-level output voltage		VID = 100 mV,		0°C	8	8.5		V
					70°C	7.8	8.4
					25°C		0	50
VOL	Low-level output voltage		VID = ± 100 mV,	IOL = 0	0°C		0	50	mV
					70°C		0	50
	Large-signal differential voltage				25°C	10	36
				RL = 10 kΩ
AVD			VO = 1 V to 6 V,		0°C	7.5	42		V/mV
	amplification
					70°C	7.5	32
					25°C	65	85
CMRR	Common-mode rejection ratio		VIC = VICRmin		0°C	60	88		dB
					70°C	60	88
	Supply-voltage rejection ratio				25°C	65	95
kSVR			VDD = 5 V to 10 V,	VO = 1.4 V	0°C	60	94		dB
	( VDD / VDD)
					70°C	60	96
			VO = 5 V,	VIC = 5 V,	25°C		1.9	4
IDD	Supply current (two amplifiers)				0°C		2.3	4.4	mA
			No load
					70°C		1.6	3.4

² Full range is 0°C to 70°C.

NOTES: 4. The typical values of input bias current and input offset current below 5 pA were determined mathematically. 5. This range also applies to each input individually.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

7