Texas Instruments TLE2074MJB, TLE2074MJ, TLE2074MFKB, TLE2074IN, TLE2074IDWR Datasheet

			TLE207x, TLE207xA, TLE207xY
			EXCALIBUR LOW-NOISE HIGH-SPEED
			JFET-INPUT OPERATIONAL AMPLIFIERS
			SLOS181A ± FEBRUARY 1997 ± REVISED MARCH 2000
D Direct Upgrades to TL05x, TL07x, and			D On-Chip Offset Voltage Trimming for
TL08x BiFET Operational Amplifiers			Improved DC Performance
D Greater Than 2× Bandwidth (10 MHz) and			D Wider Supply Rails Increase Dynamic
3× Slew Rate (45 V/µs) Than TL07x			Signal Range to ±19 V
D Ensured Maximum Noise Floor
17 nV/√	Hz

description

The TLE207x series of JFET-input operational amplifiers more than double the bandwidth and triple the slew rate of the TL07x and TL08x families of BiFET operational amplifiers. Texas Instruments Excalibur process yields a typical noise floor of 11.6 nV/√ Hz, 17-nV/√ Hz ensured maximum, offering immediate improvement in noise-sensitive circuits designed using the TL07x. The TLE207x also has wider supply voltage rails, increasing the dynamic signal range for BiFET circuits to ±19 V. On-chip zener trimming of offset voltage yields precision grades for greater accuracy in dc-coupled applications. The TLE207x are pin-compatible with lower performance BiFET operational amplifiers for ease in improving performance in existing designs.

BiFET operational amplifiers offer the inherently higher input impedance of the JFET-input transistors, without sacrificing the output drive associated with bipolar amplifiers. This makes them better suited for interfacing with high-impedance sensors or very low-level ac signals. They also feature inherently better ac response than bipolar or CMOS devices having comparable power consumption.

The TLE207x family of BiFET amplifiers are Texas Instruments highest performance BiFETs, with tighter input offset voltage and ensured maximum noise specifications. Designers requiring less stringent specifications but seeking the improved ac characteristics of the TLE207x should consider the TLE208x operational amplifier family.

Because BiFET operational amplifiers are designed for use with dual power supplies, care must be taken to observe common-mode input voltage limits and output swing when operating from a single supply. DC biasing of the input signal is required and loads should be terminated to a virtual ground node at mid-supply. Texas Instruments TLE2426 integrated virtual ground generator is useful when operating BiFET amplifiers from single supplies.

The TLE207x are fully specified at ±15 V and ±5 V. For operation in low-voltage and/or single-supply systems, Texas Instruments LinCMOS families of operational amplifiers (TLCand TLV-prefix) are recommended. When moving from BiFET to CMOS amplifiers, particular attention should be paid to slew rate and bandwidth requirements and output loading.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.

Copyright 2000, Texas Instruments Incorporated

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

1

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A ± FEBRUARY 1997 ± REVISED MARCH 2000

TLE2071 AVAILABLE OPTIONS

				PACKAGED DEVICES
		V max					CHIP FORM³
			SMALL
	TA	IO		CHIP CARRIER	CERAMIC DIP	PLASTIC DIP
		AT 25°C	OUTLINE²				(Y)
				(FK)	(JG)	(P)
			(D)
	0°C to 70°C	2 mV	TLE2071ACD	Ð	Ð	TLE2071ACP	Ð
		4 mV	TLE2071CD			TLE2071CP	TLE2071Y
	±40°C to 85°C	2 mV	TLE2071AID	Ð	Ð	TLE2071AIP	Ð
		4 mV	TLE2071ID			TLE2071IP
	±55°C to 125°C	2 mV	Ð	TLE2071AMFK	TLE2071AMJG	Ð	Ð
		4 mV	Ð	TLE2071MFK	TLE2071MJG	Ð
²	The D packages are available taped and reeled. Add R suffix to device type (e.g., TLE2071ACDR).
³	Chip-form versions are tested at T = 25°C.
			A
			TLE2072 AVAILABLE OPTIONS
				PACKAGED DEVICES			CHIP
		VIOmax
			SMALL	CHIP	CERAMIC	PLASTIC
	T						FORM³
	A	AT 25°C	OUTLINE²	CARRIER	DIP	DIP	(Y)
			(D)	(FK)	(JG)	(P)
	0°C to 70°C	3.5 mV	TLE2072ACD	Ð	Ð	TLE2072ACP	Ð
		6 mV	TLE2072CD			TLE2072CP	TLE2072Y
	±40°C to 85°C	3.5 mV	TLE2072AID	Ð	Ð	TLE2072AIP	Ð
		6 mV	TLE2072ID			TLE2072IP
	±55°C to 125°C	3.5 mV	Ð	TLE2072AMFK	TLE2072AMJG	Ð	Ð
		6 mV		TLE2072MFK	TLE2072MJG
²	The D packages are available taped and reeled. Add R suffix to device type (e.g., TLE2072ACDR).
³	Chip-form versions are tested at T = 25°C.
			A
			TLE2074 AVAILABLE OPTIONS
				PACKAGED DEVICES			CHIP
		VIOmax
			SMALL	CHIP	CERAMIC	PLASTIC
	T						FORM³
	A	AT 25°C	OUTLINE²	CARRIER	DIP	DIP	(Y)
			(DW)	(FK)	(J)	(N)
	0°C to 70°C	3 mV	TLE2074ACDW	Ð	Ð	TLE2074ACN	Ð
		5 mV	TLE2074CDW			TLE2074CN	TLE2074Y
	±40°C to 85°C	3 mV	TLE2074AIDW	Ð	Ð	TLE2074AIN	Ð
		5 mV	TLE2074IDW			TLE2074IN
	±55°C to 125°C	3 mV	Ð	TLE2074AMFK	TLE2074AMJ	Ð	Ð
		5 mV		TLE2074MFK	TLE2074MJ
²	The DW packages are available taped and reeled. Add R suffix to device type (e.g., TLE2074ACDWR).
³	Chip-form versions are tested at T = 25°C.
			A

2	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A ± FEBRUARY 1997 ± REVISED MARCH 2000

TLE2071 AND TLE2071A	TLE2072 AND TLE2072A
D, JG, OR P PACKAGE	D, JG, OR P PACKAGE
(TOP VIEW)	(TOP VIEW)

OFFSET N1		1	8		NC	1OUT		1	8		VCC +
IN ±					VCC +	1IN±
		2	7					2	7		2OUT
IN +		3	6		OUT	1IN +		3	6		2IN±
VCC ±		4	5		OFFSET N2	VCC ±		4	5		2IN+

	TLE2074 AND TLE2074A	TLE2074 AND TLE2074A
		DW PACKAGE
	J OR N PACKAGE
		(TOP VIEW)
	(TOP VIEW)

1OUT		1	14		4OUT	1OUT	1	16	4OUT
1IN±		2	13		4IN±	1IN±	2	15	4IN±
1IN+		3	12		4IN+	1IN+	3	14	4IN+
VCC +		4	11		VCC ±	VCC +	4	13	VCC ±
2IN+		5	10		3IN+	2IN+	5	12	3IN+
2IN±		6	9		3IN±	2IN±	6	11	3IN±
2OUT		7	8		3OUT	2OUT	7	10	3OUT
						NC	8	9	NC

TLE2071M AND TLE2071AM

FK PACKAGE

(TOP VIEW)

	NC	OFFSET N1	NC	NC	NC
NC	3	2	1	20 19		NC
	4				18
IN ±	5				17	VCC +
NC	6				16	NC
IN +	7				15	OUT
NC	8				14	NC
	9	10 11 12 13
	NC	VCC ±	NC	OFFSET N2	NC

NC ± No internal connection

TLE2072M AND TLE2072AM

FK PACKAGE

(TOP VIEW)

	NC	1OUT	NC	CC +	NC
				V
NC	3	2	1	20 19		NC
	4				18
1IN±	5				17	2OUT
NC	6				16	NC
1IN+	7				15	2IN±
NC	8				14	NC
	9	10 11 12 13
	NC	CC ±	NC	2IN+	NC
		V

TLE2074M AND TLE2074AM

FK PACKAGE

(TOP VIEW)

	1IN ±	1OUT	NC	4OUT	4IN ±
1IN+	3	2	1	20 19		4IN+
	4				18
NC	5				17	NC
VCC +	6				16	VCC ±
NC	7				15	NC
2IN+	8				14	3IN+
	9	10 11 12 13
	2IN ±	2OUT	NC	3OUT	3IN ±

symbol

IN + +

OUT

IN ± ±

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

3

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A ± FEBRUARY 1997 ± REVISED MARCH 2000

TLE2071Y chip information

This chip, when properly assembled, displays characteristics similar to the TLE2071C. Thermal compression or ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive epoxy or a gold-silicon preform.

					BONDING PAD ASSIGNMENTS
		(1)			(8)		(1)		VCC +
						OFFSET N1
						IN +	(3)			(7)
								+
									(6)
						IN ±	(2)	±				OUT
							(5)			(4)
						OFFSET N2
									VCC ±
					(2)
85					(7)

(3)

					CHIP THICKNESS: 15 TYPICAL
					BONDING PADS: 4 × 4 MINIMUM
					TJmax = 150°C
					TOLERANCES ARE ± 10%.
(4) (5)			(6)		ALL DIMENSIONS ARE IN MILS.
					PIN (4) IS INTERNALLY CONNECTED
					TO BACKSIDE OF THE CHIP.
		58

4	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A ± FEBRUARY 1997 ± REVISED MARCH 2000

TLE2072Y chip information

This chip, when properly assembled, displays characteristics similar to the TLE2072C. Thermal compression or ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive epoxy or a gold-silicon preform.

		BONDING PAD ASSIGNMENTS
	(1)	(8)	(7)
90	(2)		(6)
	(3)	(4)	(5)
		80

			VCC+
					(8)
1IN +	(3)	+
						(1)
1IN ±	(2)	±					1OUT
						(5)
	+
							2IN +
2OUT	(7)
				±		(6)
							2IN ±
				(4)
			VCC ±

CHIP THICKNESS: 15 TYPICAL

BONDING PADS: 4 × 4 MINIMUM

TJmax = 150°C

TOLERANCES ARE ± 10%.

ALL DIMENSIONS ARE IN MILS.

PIN (4) IS INTERNALLY CONNECTED TO BACKSIDE OF THE CHIP.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

5

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A ± FEBRUARY 1997 ± REVISED MARCH 2000

TLE2074Y chip information

This chip, when properly assembled, displays characteristics similar to the TLE2074C. Thermal compression or ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive epoxy or a gold-silicon preform.

BONDING PAD ASSIGNMENTS

	(2)	(1)	(14)	(13)
	(3)			(12)
150	(4)			(11)
	(5)			(10)
	(6)	(7)	(8)	(9)
			100

VCC+

(3)

(4)

1IN +

+

(1)

1OUT

(2)

1IN ±

±

(5)

+

2IN +

(7)

2 OUT

(6)

±

2IN ±

(10)

3IN +

+

(8)

(9)

3OUT

3IN ±

±

(12)

+

(14)

4IN +

4OUT

±

(13)

4IN ±

(11)

VCC ±

CHIP THICKNESS: 15 TYPICAL BONDING PADS: 4 × 4 MINIMUM TJmax = 150°C

TOLERANCES ARE ± 10%.

ALL DIMENSIONS ARE IN MILS.

PIN (11) IS INTERNALLY CONNECTED TO BACKSIDE OF THE CHIP.

6	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

equivalent schematic

VCC +

Q1

R2

R1

R6

R11

Q11

Q17

Q3

Q23

Q8

R3

D2

Q28

POST

IN ±

C1

Q13

Q20

Q24

OFFICE

Q15

Q19

D3

Q4

Q12

R13

BOX

R12

OUT

655303•

IN +

75265TEXASDALLAS,7

Q9

Q30

Q16

2000MARCHREVISED±1997FEBRUARY±SLOS181A

AMPLIFIERSOPERATIONALINPUT-JFET

SPEED-HIGHNOISE-LOWEXCALIBUR

TLE207xYTLE207xA,TLE207x,

Q5

R8

Q25

C6

C3

Q18

Q29

Q2

D1

Q6

Q14

Q21

Q22

Q26

Q27

Q10

R7

C5

Q31

R14

Q7

R4

R9

R10

R5

C4

C2

OFFSET N1

VCC ±

OFFSET N2

(see Note A)

(see Note A)

NOTES: A. OFFSET N1 AND OFFSET N2 are only availiable on the TLE2071x devices.

8

75265 TEXAS DALLAS, •655303 BOX OFFICE POST

equivalent schematic (continued)

ACTUAL DEVICE COMPONENT COUNT

COMPONENT	TLE2071	TLE2072	TLE2074
Transistors	33	57	114
Resistors	25	37	74
Diodes	8	5	10
Capacitors	6	11	22

2000 MARCH REVISED ± 1997 FEBRUARY ± SLOS181A

TLE207xY TLE207xA, TLE207x, SPEED-HIGH NOISE-LOW EXCALIBUR AMPLIFIERS OPERATIONAL INPUT-JFET

7±11±94 Date: Release Template

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A ± FEBRUARY 1997 ± REVISED MARCH 2000

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)²

Supply voltage, VCC + (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . .	. . . . . . . . . . 19 V
Supply voltage, VCC ± (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	. . . . . . . . ±19 V
Differential input voltage range, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	VCC + to VCC ±
Input voltage range, VI (any input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	VCC + to VCC ±
Input current, II (each input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	. . . . . . . ± 1 mA
Output current, IO (each output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	. . . . . . ± 80 mA
Total current into VCC + . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	. . . . . . 160 mA
Total current out of VCC ± . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	. . . . . . 160 mA
Duration of short-circuit current at (or below) 25°C (see Note 3) . . . . . . . . . . . . .	. . . . . . . . . . . .	. . . . . unlimited
Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	See Dissipation Rating Table
Operating free-air temperature range, TA: C suffix . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	. . 0°C to 70°C
I suffix . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	±40°C to 85°C
M suffix . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . .	±55°C to 125°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . .	±65°C to 150°C
Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . .	. . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: DW or N package . . . . . . . .		. . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J package . .	. . . . . . . . . . . .	. . . . . . . 300°C

²Stresses beyond those listed under ªabsolute maximum ratingsº may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under ªrecommended operating conditionsº is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VCC + and VCC ±.

2.Differential voltages are at the noninverting input with respect to the inverting input.

3.The output may be shorted to either supply. Temperatures and/or supply voltages must be limited to ensure that the maximum dissipation rate is not exceeded.

DISSIPATION RATING TABLE

	PACKAGE	TA ≤ 25°C	DERATING FACTOR	TA = 70°C	TA = 85°C	TA = 125°C
		POWER RATING	ABOVE TA = 25°C	POWER RATING	POWER RATING	POWER RATING
	D	725 mW	5.8 mW/°C	464 mW	377 mW	Ð
	DW	1025 mW	8.2 mW/°C	656 mW	533 mW	205 mW
	FK	1375 mW	11.0 mW/°C	880 mW	715 mW	275 mW
	J	1375 mW	11.0 mW/°C	880 mW	715 mW	275 mW
	JG	1050 mW	8.4 mW/°C	672 mW	546 mW	210 mW
	N	1150 mW	9.2 mW/°C	736 mW	598 mW	230 mW
	P	1000 mW	8.0 mW/°C	640 mW	344 mW	Ð

recommended operating conditions

			C SUFFIX		I SUFFIX		M SUFFIX		UNIT
			MIN	MAX	MIN	MAX	MIN	MAX
	Supply voltage, VCC±		± 2.25	± 19	± 2.25	± 19	± 2.25	± 19	V
	Common-mode input voltage, VIC	VCC ± = ± 5 V	± 0.9	5	± 0.8	5	± 0.8	5	V
		VCC ± = ±15 V	± 10.9	15	± 10.8	15	± 10.8	15
	Operating free-air temperature, TA		0	70	± 40	85	± 55	125	°C

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

9

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A ± FEBRUARY 1997 ± REVISED MARCH 2000

TLE2071C electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted)

PARAMETER

TEST CONDITIONS

T ²

TLE2071C

TLE2071AC

UNIT

A

MIN

TYP

MAX

MIN

TYP

MAX

VIO

Input offset voltage

25°C

0.34

4

0.3

2

mV

VIC = 0,

VO = 0,

Full range

6

4

RS = 50 Ω

αVIO

Temperature coefficient

Full range

3.2

29

3.2

29

µV/°C

of input offset voltage

IIO

Input offset current

25°C

5

100

5

100

pA

VIC = 0,

VO = 0,

Full range

1.4

1.4

nA

IIB

Input bias current

See Figure 4

25°C

15

175

15

175

pA

Full range

5

5

nA

25°C

5

5

5

5

to

to

to

to

VICR

Common-mode input

RS = 50 Ω

± 1

± 1.9

± 1

± 1.9

V

voltage range

5

5

Full range

to

to

± 0.9

± 0.9

IO = ±200 µA

25°C

3.8

4.1

3.8

4.1

Full range

3.7

3.7

VOM +

Maximum positive peak

IO = ±2 mA

25°C

3.5

3.9

3.5

3.9

V

output voltage swing

Full range

3.4

3.4

IO = ±20 mA

25°C

1.5

2.3

1.5

2.3

Full range

1.5

1.5

IO = 200 µA

25°C

± 3.5

± 4.2

± 3.5

± 4.2

Full range

± 3.4

± 3.4

VOM ±

Maximum negative peak

IO = 2 mA

25°C

± 3.7

± 4.1

± 3.7

± 4.1

V

output voltage swing

Full range

± 3.6

± 3.6

IO = 20 mA

25°C

± 1.5

± 2.4

± 1.5

± 2.4

Full range

± 1.5

± 1.5

RL = 600 Ω

25°C

80

91

80

91

Full range

79

79

AVD

Large-signal differential

VO = ± 2.3 V

RL = 2 kΩ

25°C

90

100

90

100

dB

voltage amplification

Full range

89

89

RL = 10 kΩ

25°C

95

106

95

106

Full range

94

94

r

i

Input resistance

V = 0

25°C

1012

1012

Ω

IC

VIC = 0,

Common

25°C

11

11

ci

Input capacitance

mode

pF

See Figure 5

Differential

25°C

2.5

2.5

zo

Open-loop output

f = 1 MHz

25°C

80

80

Ω

impedance

CMRR

Common-mode

VIC = VICRmin,

25°C

70

89

70

89

dB

rejection ratio

VO = 0,

RS = 50 Ω

Full range

68

68

kSVR

Supply-voltage rejection

VCC ± = ± 5 V to ± 15 V,

25°C

82

99

82

99

dB

ratio( VCC± / VIO)

VO = 0,

RS = 50 Ω

Full range

80

80

² Full range is 0°C to 70°C.

10	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A ± FEBRUARY 1997 ± REVISED MARCH 2000

TLE2071C electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted) (continued)

	PARAMETER	TEST CONDITIONS		T ²	TLE2071C			TLE2071AC			UNIT
				A	MIN	TYP	MAX	MIN	TYP	MAX
ICC	Supply current	VO = 0,	No load	25°C	1.35	1.6	2.2	1.35	1.6	2.2	mA
				Full range			2.2			2.2
IOS	Short-circuit output	VO = 0	VID = 1 V	25°C		± 35			± 35		mA
	current		VID = ± 1 V			45			45

² Full range is 0°C to 70°C.

TLE2071C operating characteristics at specified free-air temperature, VCC ± = ±5 V

PARAMETER

TEST CONDITIONS

T ²

TLE2071C

TLE2071AC

UNIT

A

MIN TYP

MAX

MIN TYP

MAX

25°C

35

35

SR +

Positive slew rate

V/µs

VO(PP) = ± 2.3 V,

Full

23

23

range

AVD = ±1,

RL = 2 kΩ,

25°C

38

38

CL = 100 pF,

See Figure 1

SR ±

Negative slew rate

V/µs

Full

23

23

range

AVD = ± 1,

To 10 mV

0.25

0.25

ts

Settling time

2-V step,

25°C

µs

RL = 1 kΩ,

To 1 mV

0.4

0.4

CL = 100 pF

Vn

Equivalent input noise

f = 10 Hz

25°C

28

55

28

55

nV/√ Hz

voltage

f = 10 kHz

11.6

17

11.6

17

RS = 20 Ω,

f = 10 Hz to

6

6

Peak-to-peak equivalent

See Figure 3

10 kHz

VN(PP)

25°C

µV

input noise voltage

f = 0.1 Hz to

0.6

0.6

10 Hz

Equivalent input noise

In

VIC = 0,

f = 10 kHz

25°C

2.8

2.8

fA/√ Hz

current

Total harmonic distortion

VO(PP) = 5 V,

AVD = 10,

25°C

THD + N

f = 1 kHz,

RL = 2 kΩ,

0.013%

0.013%

plus noise

RS = 25 Ω

B1

Unity-gain bandwidth

VI = 10 mV,

RL = 2 kΩ,

25°C

9.4

9.4

MHz

CL = 25 pF,

See Figure 2

BOM

Maximum output-swing

VO(PP) = 4 V,

AVD = ± 1,

25°C

2.8

2.8

MHz

bandwidth

RL = 2 kΩ ,

CL = 25 pF

φm

Phase margin at unity

VI = 10 mV,

RL = 2 kΩ,

25°C

56°

56°

gain

CL = 25 pF,

See Figure 2

² Full range is 0°C to 70°C.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

11

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A ± FEBRUARY 1997 ± REVISED MARCH 2000

TLE2071C electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted)

PARAMETER

TEST CONDITIONS

T ²

TLE2071C

TLE2071AC

UNIT

A

MIN

TYP

MAX

MIN

TYP

MAX

VIO

Input offset voltage

25°C

0.49

4

0.47

2

mV

VIC = 0,

VO = 0,

Full range

6

4

RS = 50 Ω

αVIO

Temperature coefficient

Full range

3.2

29

3.2

29

µV/°C

of input offset voltage

IIO

Input offset current

25°C

6

100

6

100

pA

VIC = 0,

VO = 0,

Full range

1.4

1.4

nA

IIB

Input bias current

See Figure 4

25°C

20

175

20

175

pA

Full range

5

5

nA

25°C

15

15

15

15

to

to

to

to

VICR

Common-mode input

RS = 50 Ω

± 11

± 11.9

± 11

± 11.9

V

voltage range

15

15

Full range

to

to

± 10.9

± 10.9

IO = ±200 µA

25°C

13.8

14.1

13.8

14.1

Full range

13.7

13.7

VOM +

Maximum positive peak

IO = ±2 mA

25°C

13.5

13.9

13.5

13.9

V

output voltage swing

Full range

13.4

13.4

IO = ±20 mA

25°C

11.5

12.3

11.5

12.3

Full range

11.5

11.5

IO = 200 µA

25°C

± 13.8

± 14.2

± 13.8

± 14.2

Full range

± 13.7

± 13.7

VOM ±

Maximum negative peak

IO = 2 mA

25°C

± 13.5

± 14

±13.5

± 14

V

output voltage swing

Full range

± 13.4

± 13.4

IO = 20 mA

25°C

± 11.5

± 12.4

± 11.5

± 12.4

Full range

± 11.5

± 11.5

RL = 600 Ω

25°C

80

96

80

96

Full range

79

79

AVD

Large-signal differential

VO = ± 10 V

RL = 2 kΩ

25°C

90

109

90

109

dB

voltage amplification

Full range

89

89

RL = 10 kΩ

25°C

95

118

95

118

Full range

94

94

r

i

Input resistance

V = 0

25°C

1012

1012

Ω

IC

VIC = 0,

Common

25°C

7.5

7.5

ci

Input capacitance

mode

pF

See Figure 5

Differential

25°C

2.5

2.5

zo

Open-loop output

f = 1 MHz

25°C

80

80

Ω

impedance

CMRR

Common-mode

VIC = VICRmin,

25°C

80

98

80

98

dB

rejection ratio

VO = 0,

RS = 50 Ω

Full range

79

79

kSVR

Supply-voltage rejection

VCC ± = ± 5 V to ± 15 V,

25°C

82

99

82

99

dB

ratio ( VCC± / VIO)

VO = 0,

RS = 50 Ω

Full range

80

81

² Full range is 0°C to 70°C.

12	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A ± FEBRUARY 1997 ± REVISED MARCH 2000

TLE2071C electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted) (continued)

	PARAMETER	TEST CONDITIONS		T ²	TLE2071C			TLE2071AC			UNIT
				A	MIN	TYP	MAX	MIN	TYP	MAX
ICC	Supply current	VO = 0,	No load	25°C	1.35	1.7	2.2	1.35	1.7	2.2	mA
				Full range			2.2			2.2
IOS	Short-circuit output	VO = 0	VID = 1 V	25°C	± 30	± 45		± 30	± 45		mA
	current		VID = ± 1 V		30	48		30	48

² Full range is 0°C to 70°C.

TLE2071C operating characteristics at specified free-air temperature, VCC ± = ±15 V

PARAMETER

TEST CONDITIONS

T ²

TLE2071C

TLE2071AC

UNIT

A

MIN

TYP

MAX

MIN

TYP

MAX

25°C

30

40

30

40

SR +

Positive slew rate

VO(PP) = 10 V,

AVD = ± 1,

Full

27

27

V/µs

range

RL = 2 kΩ,

CL = 100 pF,

25°C

30

45

30

45

See Figure 1

SR ±

Negative slew rate

Full

27

27

V/µs

range

AVD = ± 1,

To 10 mV

0.4

0.4

ts

Settling time

10-V step,

25°C

µs

RL = 1 kΩ,

To 1 mV

1.5

1.5

CL = 100 pF

Vn

Equivalent input noise

f = 10 Hz

25°C

28

55

28

55

nV√ Hz

voltage

f = 10 kHz

11.6

17

11.6

17

RS = 20 Ω,

f = 10 Hz to

6

6

Peak-to-peak equivalent

See Figure 3

10 kHz

VN(PP)

25°C

µV

input noise voltage

f = 0.1 Hz to

0.6

0.6

10 Hz

In

Equivalent input noise

VIC = 0,

f = 10 kHz

25°C

2.8

2.8

fA/√ Hz

current

Total harmonic distortion

VO(PP) = 20 V,

AVD = 10,

25°C

THD + N

f = 1 kHz,

RL = 2 kΩ,

0.008%

0.008%

plus noise

RS = 25 Ω

B1

Unity-gain bandwidth

VI = 10 mV,

RL = 2 kΩ,

25°C

8

10

8

10

MHz

CL = 25 pF,

See Figure 2

BOM

Maximum output-swing

VO(PP) = 20 V,

AVD = ± 1,

25°C

478

637

478

637

kHz

bandwidth

RL = 2 kΩ,

CL = 25 pF

φm

Phase margin at unity

VI = 10 mV,

RL = 2 kΩ,

25°C

57°

57°

gain

CL = 25 pF,

See Figure 2

² Full range is 0°C to 70°C.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

13

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A ± FEBRUARY 1997 ± REVISED MARCH 2000

TLE2071I electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted)

PARAMETER

TEST CONDITIONS

T ²

TLE2071I

TLE2071AI

UNIT

A

MIN

TYP

MAX

MIN

TYP

MAX

VIO

Input offset voltage

25°C

0.34

4

0.3

2

mV

VIC = 0,

VO = 0,

Full range

7.6

5.6

RS = 50 Ω,

αVIO

Temperature coefficient

Full range

3.2

29

3.2

29

µV/°C

of input offset voltage

IIO

Input offset current

25°C

5

100

5

100

pA

VIC = 0,

VO = 0,

Full range

5

5

nA

IIB

Input bias current

See Figure 4

25°C

15

175

15

175

pA

Full range

10

10

nA

25°C

5

5

5

5

to

to

to

to

VICR

Common-mode input

RS = 50 Ω

± 1

± 1.9

± 1

± 1.9

V

voltage range

5

5

Full range

to

to

± 0.8

± 0.8

IO = ±200 µA

25°C

3.8

4.1

3.8

4.1

Full range

3.7

3.7

VOM +

Maximum positive peak

IO = ±2 mA

25°C

3.5

3.9

3.5

3.9

V

output voltage swing

Full range

3.4

3.4

IO = ±20 mA

25°C

1.5

2.3

1.5

2.3

Full range

1.5

1.5

IO = 200 µA

25°C

± 3.8

± 4.2

± 3.8

± 4.2

Full range

± 3.7

± 3.7

VOM ±

Maximum negative peak

IO = 2 mA

25°C

± 3.5

± 4.1

± 3.5

± 4.1

V

output voltage swing

Full range

± 3.4

± 3.4

IO = 20 mA

25°C

± 1.5

± 2.4

± 1.5

± 2.4

Full range

± 1.5

± 1.5

RL = 600 Ω

25°C

80

91

80

91

Full range

79

79

AVD

Large-signal differential

VO = ± 2.3 V

RL = 2 kΩ

25°C

90

100

90

100

dB

voltage amplification

Full range

89

89

RL = 10 kΩ

25°C

95

106

95

106

Full range

94

94

r

i

Input resistance

V

IC

= 0

25°C

1012

1012

Ω

VIC = 0,

Common

25°C

11

11

ci

Input capacitance

mode

pF

See Figure 5

Differential

25°C

2.5

2.5

zo

Open-loop output

f = 1 MHz

25°C

80

80

Ω

impedance

CMRR

Common-mode

VIC = VICRmin,

25°C

70

89

70

89

dB

rejection ratio

V

O

= 0,

R

S

= 50 Ω

Full range

68

68

kSVR

Supply-voltage rejection

VCC ± = ± 5 V to ± 15 V,

25°C

82

99

82

99

dB

ratio ( VCC± / VIO)

VO = 0,

RS = 50 Ω

Full range

80

80

² Full range is ± 40°C to 85°C.

14	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A ± FEBRUARY 1997 ± REVISED MARCH 2000

TLE2071I electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted) (continued)

	PARAMETER	TEST CONDITIONS		T ²		TLE2071I		TLE2071AI			UNIT
				A	MIN	TYP	MAX	MIN	TYP	MAX
ICC	Supply current	VO = 0,	No load	25°C	1.35	1.6	2.2	1.35	1.6	2.2	mA
				Full range			2.2			2.2
IOS	Short-circuit output	VO = 0	VID = 1 V	25°C		± 35			± 35		mA
	current		VID = ± 1 V			45			45

² Full range is ± 40°C to 85°C.

TLE2071I operating characteristics at specified free-air temperature, VCC ± = ±5 V

PARAMETER

TEST CONDITIONS

T ²

TLE2071I

TLE2071AI

UNIT

A

MIN TYP

MAX

MIN TYP

MAX

25°C

35

35

SR +

Positive slew rate

V/µs

VO(PP) = ± 2.3 V,

Full

22

22

range

AVD = ±1,

RL = 2 kΩ,

25°C

38

38

CL = 100 pF,

See Figure 1

SR ±

Negative slew rate

V/µs

Full

22

22

range

AVD = ± 1,

To 10 mV

0.25

0.25

ts

Settling time

2-V step,

25°C

µs

RL = 1 kΩ,

To 1 mV

0.4

0.4

CL = 100 pF

Vn

Equivalent input noise

f = 10 Hz

25°C

28

55

28

55

nV/√ Hz

voltage

f = 10 kHz

11.6

17

11.6

17

RS = 20 Ω,

f = 10 Hz to

6

6

Peak-to-peak equivalent

See Figure 3

10 kHz

VN(PP)

25°C

µV

input noise voltage

f = 0.1 Hz to

0.6

0.6

10 Hz

Equivalent input noise

25°C

In

VIC = 0,

f = 10 kHz

2.8

2.8

fA/√ Hz

current

Total harmonic distortion

VO(PP) = 5 V, AVD = 10,

25°C

THD + N

f = 1 kHz,

RL = 2 kΩ,

0.013%

0.013%

plus noise

RS = 25 Ω

B1

Unity-gain bandwidth

VI = 10 mV,

RL = 2 kΩ,

25°C

9.4

9.4

MHz

CL = 25 pF,

See Figure 2

BOM

Maximum output-swing

VO(PP) = 4 V, AVD = ± 1,

25°C

2.8

2.8

MHz

bandwidth

RL = 2 kΩ ,

CL = 25 pF

φm

Phase margin at unity gain

VI = 10 mV,

RL = 2 kΩ,

25°C

56°

56°

CL = 25 pF,

See Figure 2

² Full range is ± 40°C to 85°C.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

15

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A ± FEBRUARY 1997 ± REVISED MARCH 2000

TLE2071I electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted)

PARAMETER

TEST CONDITIONS

T ²

TLE2071I

TLE2071AI

UNIT

A

MIN

TYP

MAX

MIN

TYP

MAX

VIO

Input offset voltage

25°C

0.49

4

0.47

2

mV

VIC = 0,

VO = 0,

Full range

7.6

5.6

RS = 50 Ω,

αVIO

Temperature coefficient

Full range

3.2

29

3.2

29

µV/°C

of input offset voltage

IIO

Input offset current

25°C

6

100

6

100

pA

VIC = 0,

VO = 0,

Full range

5

5

nA

IIB

Input bias current

See Figure 4

25°C

20

175

20

175

pA

Full range

10

10

nA

25°C

15

15

15

15

to

to

to

to

VICR

Common-mode input

RS = 50 Ω

± 11

± 11.9

± 11

± 11.9

V

voltage range

15

15

Full range

to

to

± 10.8

± 10.8

IO = ±200 µA

25°C

13.8

14.1

13.8

14.1

Full range

13.7

13.7

VOM +

Maximum positive peak

IO = ±2 mA

25°C

13.5

13.9

13.5

13.9

V

output voltage swing

Full range

13.4

13.4

IO = ±20 mA

25°C

11.5

12.3

11.5

12.3

Full range

11.5

11.5

IO = 200 µA

25°C

± 13.8

± 14.2

± 13.8

± 14.2

Full range

± 13.7

± 13.7

VOM ±

Maximum negative peak

IO = 2 mA

25°C

± 13.5

± 14

±13.5

± 14

V

output voltage swing

Full range

± 13.4

± 13.4

IO = 20 mA

25°C

± 11.5

± 12.4

± 11.5

± 12.4

Full range

± 11.5

± 11.5

RL = 600 Ω

25°C

80

96

80

96

Full range

79

79

AVD

Large-signal differential

VO = ± 10 V

RL = 2 kΩ

25°C

90

109

90

109

dB

voltage amplification

Full range

89

89

RL = 10 kΩ

25°C

95

118

95

118

Full range

94

94

r

i

Input resistance

V = 0

25°C

1012

1012

Ω

IC

VIC = 0,

Common

25°C

7.5

7.5

ci

Input capacitance

mode

pF

See Figure 5

Differential

25°C

2.5

2.5

zo

Open-loop output

f = 1 MHz

25°C

80

80

Ω

impedance

CMRR

Common-mode

VIC = VICRmin,

25°C

80

98

80

98

dB

VO = 0,

rejection ratio

Full range

79

79

RS = 50 Ω

kSVR

Supply-voltage rejection

VCC ± = ± 5 V to ± 15 V,

25°C

82

99

82

99

dB

ratio ( VCC± / VIO)

VO = 0,

RS = 50 Ω

Full range

80

80

² Full range is ± 40°C to 85°C.

16	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A ± FEBRUARY 1997 ± REVISED MARCH 2000

TLE2071I electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted) (continued)

	PARAMETER	TEST CONDITIONS		T ²		TLE2071I		TLE2071AI			UNIT
				A	MIN	TYP	MAX	MIN	TYP	MAX
ICC	Supply current	VO = 0,	No load	25°C	1.35	1.7	2.2	1.35	1.7	2.2	mA
				Full range			2.2			2.2
IOS	Short-circuit output	VO = 0	VID = 1 V	25°C	± 30	± 45		± 30	± 45		mA
	current		VID = ± 1 V		30	48		30	48

² Full range is ± 40°C to 85°C.

TLE2071I operating characteristics at specified free-air temperature, VCC ± = ±15 V

PARAMETER

TEST CONDITIONS

T ²

TLE2071I

TLE2071AI

UNIT

A

MIN

TYP

MAX

MIN

TYP

MAX

25°C

30

40

30

40

SR +

Positive slew rate

VO(PP) = ± 10 V,

Full

24

24

V/µs

range

AVD = ±1,

RL = 2 kΩ,

25°C

30

45

30

45

CL = 100 pF,

See Figure 1

SR ±

Negative slew rate

V/µs

Full

24

24

range

AVD = ± 1,

To 10 mV

0.4

0.4

ts

Settling time

10-V step,

25°C

µs

RL = 1 kΩ,

To 1 mV

1.5

1.5

CL = 100 pF

Equivalent input noise

f = 10 Hz

25°C

28

55

28

55

Vn

nV/√ Hz

voltage

f = 10 kHz

11.6

17

11.6

17

RS = 20 Ω,

f = 10 Hz to

6

6

Peak-to-peak equivalent

See Figure 3

10 kHz

VN(PP)

25°C

µV

input noise voltage

f = 0.1 Hz to

0.6

0.6

10 Hz

Equivalent input noise

In

VIC = 0,

f = 10 kHz

25°C

2.8

2.8

fA/√ Hz

current

Total harmonic distortion

VO(PP) = 20 V,

AVD = 10,

25°C

THD + N

f = 1 kHz,

RL = 2 kΩ,

0.008%

0.008%

plus noise

RS = 25 Ω

B1

Unity-gain bandwidth

VI = 10 mV,

RL = 2 kΩ,

25°C

8

10

8

10

MHz

CL = 25 pF,

See Figure 2

BOM

Maximum output-swing

VO(PP) = 20 V,

AVD = ± 1,

25°C

478

637

478

637

kHz

bandwidth

RL = 2 kΩ,

CL = 25 pF

φm

Phase margin at unity gain

VI = 10 mV,

RL = 2 kΩ,

25°C

57°

57°

CL = 25 pF,

See Figure 2

² Full range is ± 40°C to 85°C.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

17

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A ± FEBRUARY 1997 ± REVISED MARCH 2000

TLE2071M electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted)

PARAMETER

TEST CONDITIONS

T ²

TLE2071M

TLE2071AM

UNIT

A

MIN

TYP

MAX

MIN

TYP

MAX

VIO

Input offset voltage

25°C

0.34

4

0.3

2

mV

VIC = 0,

VO = 0,

Full range

9.2

7.2

RS = 50 Ω,

αVIO

Temperature coefficient

Full range

3.2

29

3.2

29

µV/°C

of input offset voltage

IIO

Input offset current

25°C

5

100

5

100

pA

VIC = 0,

VO = 0,

Full range

20

20

nA

IIB

Input bias current

See Figure 4

25°C

15

175

15

175

pA

Full range

60

60

nA

25°C

5

5

5

5

to

to

to

to

VICR

Common-mode input

RS = 50 Ω

± 1

± 1.9

± 1

± 1.9

V

voltage range

5

5

Full range

to

to

± 0.8

± 0.8

IO = ±200 µA

25°C

3.8

4.1

3.8

4.1

Full range

3.6

3.6

VOM +

Maximum positive peak

IO = ±2 mA

25°C

3.5

3.9

3.5

3.9

V

output voltage swing

Full range

3.3

3.3

IO = ±20 mA

25°C

1.5

2.3

1.5

2.3

Full range

1.4

1.4

IO = 200 µA

25°C

± 3.8

± 4.2

± 3.8

± 4.2

Full range

± 3.6

± 3.6

VOM ±

Maximum negative peak

IO = 2 mA

25°C

± 3.5

± 4.1

± 3.5

± 4.1

V

output voltage swing

Full range

± 3.3

± 3.3

IO = 20 mA

25°C

± 1.5

± 2.4

± 1.5

± 2.4

Full range

± 1.4

± 1.4

RL = 600 Ω

25°C

80

91

80

91

Full range

78

78

AVD

Large-signal differential

VO = ± 2.3 V

RL = 2 kΩ

25°C

90

100

90

100

dB

voltage amplification

Full range

88

88

RL = 10 kΩ

25°C

95

106

95

106

Full range

93

93

r

i

Input resistance

V = 0

25°C

1012

1012

Ω

IC

VIC = 0,

Common

25°C

11

11

ci

Input capacitance

mode

pF

See Figure 5

Differential

25°C

2.5

2.5

zo

Open-loop output

f = 1 MHz

25°C

80

80

Ω

impedance

CMRR

Common-mode

VIC = VICRmin,

25°C

70

89

70

89

dB

rejection ratio

VO = 0,

RS = 50 Ω

Full range

68

68

kSVR

Supply-voltage rejection

VCC ± = ± 5 V to ± 15 V,

25°C

82

99

82

99

dB

ratio ( VCC± / VIO)

VO = 0,

RS = 50 Ω

Full range

80

80

On products compliant to MIL-PRF-

38535, Class B, this parameter

is not production tested.

² Full range is ± 55°C to 125°C.

18	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A ± FEBRUARY 1997 ± REVISED MARCH 2000

TLE2071M electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted)

	PARAMETER	TEST CONDITIONS		T ²	TLE2071M			TLE2071AM			UNIT
				A	MIN	TYP	MAX	MIN	TYP	MAX
ICC	Supply current	VO = 0,	No load	25°C	1.35	1.6	2.2	1.35	1.6	2.2	mA
				Full range			2.2			2.2
IOS	Short-circuit output	VO = 0	VID = 1 V	25°C		± 35			± 35		mA
	current		VID = ± 1 V			45			45

² Full range is ± 55°C to 125°C.

TLE2071M operating characteristics at specified free-air temperature, VCC ± = ±5 V

PARAMETER

TEST CONDITIONS

T ²

TLE2071M

TLE2071AM

UNIT

A

MIN TYP

MAX

MIN TYP

MAX

25°C

35

35

SR +

Positive slew rate

VO(PP) = ± 2.3 V,

Full

20

20

V/µs

range

AVD = ±1,

RL = 2 kΩ,

25°C

38

38

CL = 100 pF,

See Figure 1

SR ±

Negative slew rate

Full

20

20

V/µs

range

AVD = ± 1,

To 10 mV

0.25

0.25

ts

Settling time

2-V step,

25°C

µs

RL = 1 kΩ,

To 1 mV

0.4

0.4

CL = 100 pF

Vn

Equivalent input noise

f = 10 Hz

25°C

28

55

28

55

voltage

nV/√ Hz

f = 10 kHz

11.6

17

11.6

17

RS = 20 Ω,

f = 10 Hz to

6

6

Peak-to-peak equivalent

See Figure 3

10 kHz

VN(PP)

25°C

µV

input noise voltage

f = 0.1 Hz to

0.6

0.6

10 Hz

Equivalent input noise

In

VIC = 0,

f = 10 kHz

25°C

2.8

2.8

fA/√ Hz

current

Total harmonic distortion

VO(PP) = 5 V,

AVD = 10,

25°C

THD + N

f = 1 kHz,

RL = 2 kΩ,

0.013%

0.013%

plus noise

RS = 25 Ω

B1

Unity-gain bandwidth

VI = 10 mV,

RL = 2 kΩ,

25°C

9.4

9.4

MHz

CL = 25 pF,

See Figure 2

BOM

Maximum output-swing

VO(PP) = 4 V,

AVD = ± 1,

25°C

2.8

2.8

MHz

bandwidth

RL = 2 kΩ ,

CL = 25 pF

φm

Phase margin at unity

VI = 10 mV,

RL = 2 kΩ,

25°C

56°

56°

gain

CL = 25 pF,

See Figure 2

On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested. ² Full range is ± 55°C to 125°C.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

19

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A ± FEBRUARY 1997 ± REVISED MARCH 2000

TLE2071M electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted)

PARAMETER

TEST CONDITIONS

T ²

TLE2071M

TLE2071AM

UNIT

A

MIN

TYP

MAX

MIN

TYP

MAX

VIO

Input offset voltage

25°C

0.49

4

0.47

2

mV

VIC = 0,

VO = 0,

Full range

9.2

7.2

RS = 50 Ω

αVIO

Temperature coefficient

Full range

3.2

29

3.2

29

µV/°C

of input offset voltage

IIO

Input offset current

25°C

6

100

6

100

pA

VIC = 0,

VO = 0,

Full range

20

20

nA

IIB

Input bias current

See Figure 4

25°C

20

175

20

175

pA

Full range

60

60

nA

25°C

15

15

15

15

to

to

to

to

VICR

Common-mode input

RS = 50 Ω

± 11

± 11.9

± 11

± 11.9

V

voltage range

15

15

Full range

to

to

± 10.9

± 10.9

IO = ±200 µA

25°C

13.8

14.1

13.8

14.1

Full range

13.6

13.6

VOM +

Maximum positive peak

IO = ±2 mA

25°C

13.5

13.9

13.5

13.9

V

output voltage swing

Full range

13.3

13.3

IO = ±20 mA

25°C

11.5

12.3

11.5

12.3

Full range

11.4

11.4

IO = 200 µA

25°C

± 13.8

± 14.2

± 13.8

± 14.2

Full range

± 13.6

± 13.6

VOM ±

Maximum negative peak

IO = 2 mA

25°C

± 13.5

± 14

±13.5

± 14

V

output voltage swing

Full range

± 13.3

± 13.3

IO = 20 mA

25°C

± 11.5

± 12.4

± 11.5

± 12.4

Full range

± 11.4

± 11.4

RL = 600 Ω

25°C

80

96

80

96

Full range

78

78

AVD

Large-signal differential

VO = ± 10 V

RL = 2 kΩ

25°C

90

109

90

109

dB

voltage amplification

Full range

88

88

RL = 10 kΩ

25°C

95

118

95

118

Full range

93

93

r

i

Input resistance

V = 0

25°C

1012

1012

Ω

IC

VIC = 0,

Common

25°C

7.5

7.5

ci

Input capacitance

mode

pF

See Figure 5

Differential

25°C

2.5

2.5

zo

Open-loop output

f = 1 MHz

25°C

80

80

Ω

impedance

CMRR

Common-mode

VIC = VICRmin,

25°C

80

98

80

98

dB

rejection ratio

VO = 0,

RS = 50 Ω

Full range

78

78

kSVR

Supply-voltage rejection

VCC ± = ± 5 V to ± 15 V,

25°C

82

99

82

99

dB

ratio ( VCC± / VIO)

VO = 0,

RS = 50 Ω

Full range

80

80

On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.

² Full range is ± 55°C to 125°C.

20	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A ± FEBRUARY 1997 ± REVISED MARCH 2000

TLE2071M electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted) (continued)

	PARAMETER	TEST CONDITIONS		T ²	TLE2071M			TLE2071AM			UNIT
				A	MIN	TYP	MAX	MIN	TYP	MAX
ICC	Supply current	VO = 0,	No load	25°C	1.35	1.7	2.2	1.35	1.7	2.2	mA
				Full range			2.2			2.2
IOS	Short-circuit output current	VO = 0	VID = 1 V	25°C	± 30	± 45		± 30	± 45		mA
			VID = ± 1 V		30	48		30	48

² Full range is ± 55°C to 125°C.

TLE2071M operating characteristics at specified free-air temperature, VCC ± = ±15 V

PARAMETER

TEST CONDITIONS

T ²

TLE2071M

TLE2071AM

UNIT

A

MIN

TYP

MAX

MIN

TYP

MAX

25°C

30

40

30

40

SR +

Positive slew rate

VO(PP) = 10 V,

AVD = ± 1,

Full

22

22

V/µs

range

RL = 2 kΩ,

CL = 100 pF,

25°C

30

45

30

45

See Figure 1

SR ±

Negative slew rate

Full

22

22

V/µs

range

AVD = ± 1,

To 10 mV

0.4

0.4

ts

Settling time

10-V step,

25°C

µs

RL = 1 kΩ,

To 1 mV

1.5

1.5

CL = 100 pF

Vn

Equivalent input noise

f = 10 Hz

25°C

28

55

28

55

voltage

nV/√ Hz

f = 10 kHz

11.6

17

11.6

17

RS = 20 Ω,

f = 10 Hz to

6

6

Peak-to-peak equivalent

See Figure 3

10 kHz

VN(PP)

25°C

µV

input noise voltage

f = 0.1 Hz to

0.6

0.6

10 Hz

Equivalent input noise

In

VIC = 0,

f = 10 kHz

25°C

2.8

2.8

fA/√ Hz

current

Total harmonic distortion

VO(PP) = 20 V,

AVD = 10,

25°C

THD + N

f = 1 kHz,

RL = 2 kΩ,

0.008%

0.008%

plus noise

RS = 25 Ω

B1

Unity-gain bandwidth

VI = 10 mV,

RL = 2 kΩ,

25°C

8

10

8

10

MHz

CL = 25 pF,

See Figure 2

BOM

Maximum output-swing

VO(PP) = 20 V,

AVD = ± 1,

25°C

478

637

478

637

kHz

bandwidth

RL = 2 kΩ,

CL = 25 pF

φm

Phase margin at unity

VI = 10 mV,

RL = 2 kΩ,

25°C

57°

57°

gain

CL = 25 pF,

See Figure 2

On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.

² Full range is ± 55°C to 125°C.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

21

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A ± FEBRUARY 1997 ± REVISED MARCH 2000

TLE2071Y electrical characteristics at VCC ± = ±15 V, TA = 25°C

		PARAMETER	TEST CONDITIONS			TLE2071Y			UNIT
						MIN	TYP	MAX
VIO		Input offset voltage	VIC = 0,	VO = 0,	RS = 50 Ω		0.49	4	mV
IIO		Input offset current	VIC = 0,	VO = 0,	See Figure 4		6	100	pA
IIB		Input bias current					20	175	pA
			RS = 50 Ω			15	15
VICR		Common-mode input voltage range				to	to		V
						± 11	11.9
			IO = ± 200 µA			13.8	14.1
VOM +		Maximum positive peak output voltage swing	IO = ± 2 mA			13.5	13.9		V
			IO = ± 20 mA			11.5	12.3
			IO = 200 µA			± 13.8	± 14.2
VOM ±		Maximum negative peak output voltage swing	IO = 2 mA			± 13.5	± 14		V
			IO = 20 mA			± 11.5	± 12.4
				RL = 600 Ω		80	96
AVD		Large-signal differential voltage amplification	VO = ± 10 V	RL = 2 kΩ		90	109		dB
				RL = 10 kΩ		95	118
r	i	Input resistance	V = 0				1012		Ω
			IC
ci		Input capacitance	VO = 0,	Common mode			7.5		pF
			See Figure 5	Differential			2.5
zo		Open-loop output impedance	f = 1 MHz				80		Ω
CMRR		Common-mode rejection ratio	VIC = VICRmin,		VO = 0,	80	98		dB
			RS = 50 Ω
kSVR		Supply-voltage rejection ratio ( VCC± / VIO)	VCC ± = ± 5 V to ±15 V,		VO = 0,	82	99		dB
			RS = 50 Ω
ICC		Supply current	VO = 0,	No load		1.35	1.7	2.2	mA
IOS		Short-circuit output current	VO = 0	VID = 1 V		± 30	± 45		mA
				VID = ± 1 V		30	48

22	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A ± FEBRUARY 1997 ± REVISED MARCH 2000

TLE2072C electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted)

PARAMETER

TEST CONDITIONS

T ²

TLE2072C

TLE2072AC

UNIT

A

MIN

TYP

MAX

MIN

TYP

MAX

VIO

Input offset voltage

25°C

0.9

6

0.65

3.5

mV

VIC = 0,

VO = 0,

Full range

7.8

5.3

RS = 50 Ω

αVIO

Temperature coefficient

Full range

2.3

25

2.3

25

µV/°C

of input offset voltage

IIO

Input offset current

25°C

5

100

5

100

pA

VIC = 0,

VO = 0,

Full range

1.4

1.4

nA

IIB

Input bias current

See Figure 4

25°C

15

175

15

175

pA

Full range

5

5

nA

25°C

5

5

5

5

to

to

to

to

VICR

Common-mode input

RS = 50 Ω

± 1

± 1.9

± 1

± 1.9

V

voltage range

5

5

Full range

to

to

± 0.9

± 0.9

IO = ±200 µA

25°C

3.8

4.1

3.8

4.1

Full range

3.7

3.7

VOM +

Maximum positive peak

IO = ±2 mA

25°C

3.5

3.9

3.5

3.9

V

output voltage swing

Full range

3.4

3.4

IO = ±20 mA

25°C

1.5

2.3

1.5

2.3

Full range

1.5

1.5

IO = 200 µA

25°C

± 3.8

± 4.2

± 3.8

± 4.2

Full range

± 3.7

± 3.7

VOM ±

Maximum negative peak

IO = 2 mA

25°C

± 3.5

± 4.1

± 3.5

± 4.1

V

output voltage swing

Full range

± 3.4

± 3.4

IO = 20 mA

25°C

± 1.5

± 2.4

± 1.5

± 2.4

Full range

± 1.5

± 1.5

RL = 600 Ω

25°C

80

91

80

91

Full range

79

79

AVD

Large-signal differential

VO = ± 2.3 V

RL = 2 kΩ

25°C

90

100

90

100

dB

voltage amplification

Full range

89

89

RL = 10 kΩ

25°C

95

106

95

106

Full range

94

94

r

i

Input resistance

V = 0

25°C

1012

1012

Ω

IC

VIC = 0,

Common

25°C

11

11

ci

Input capacitance

mode

pF

See Figure 5

Differential

25°C

2.5

2.5

zo

Open-loop output

f = 1 MHz

25°C

80

80

Ω

impedance

CMRR

Common-mode

VIC = VICRmin,

25°C

70

89

70

89

dB

rejection ratio

VO = 0,

RS = 50 Ω

Full range

68

68

kSVR

Supply-voltage rejection

VCC ± = ± 5 V to ± 15 V,

25°C

82

99

82

99

dB

ratio( VCC± / VIO)

VO = 0,

RS = 50 Ω

Full range

80

80

² Full range is 0°C to 70°C.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

23

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A ± FEBRUARY 1997 ± REVISED MARCH 2000

TLE2072C electrical characteristics at specified free-air temperature, VCC ± = ±5 V (unless otherwise noted)

(continued)

	PARAMETER	TEST CONDITIONS		TA	TLE2072C			TLE2072AC			UNIT
					MIN	TYP	MAX	MIN	TYP	MAX
ICC	Supply current	VO = 0,	No load	25°C	2.7	2.9	3.9	2.7	2.9	3.9	mA
	(both channels)			Full range			3.9			3.9
ax	Crosstalk attenuation	VIC = 0,	RL = 2 kΩ	25°C		120			120		dB
IOS	Short-circuit output	VO = 0	VID = 1 V	25°C		± 35			± 35		mA
	current		VID = ± 1 V			45			45

TLE2072C operating characteristics at specified free-air temperature, VCC ± = ±5 V

	PARAMETER	TEST CONDITIONS		T ²	TLE2072C		TLE2072AC		UNIT
				A	MIN TYP	MAX	MIN TYP	MAX
				25°C	35		35
SR +	Positive slew rate								V/µs
		VO(PP) = ± 2.3 V,		Full	22		22
				range
		AVD = ±1,	RL = 2 kΩ,
				25°C	38		38
		CL = 100 pF,	See Figure 1
SR ±	Negative slew rate								V/µs
				Full	22		22
				range
		AVD = ± 1,	To 10 mV		0.25		0.25
ts	Settling time	2-V step,		25°C					µs
		RL = 1 kΩ,	To 1 mV		0.4		0.4
		CL = 100 pF
Vn	Equivalent input noise		f = 10 Hz	25°C	28	55	28	55
									nV/√ Hz
	voltage		f = 10 kHz		11.6	17	11.6	17
		RS = 20 Ω,
	Peak-to-peak equiva-		f = 10 Hz to		6		6
		See Figure 3	10 kHz
VN(PP)				25°C					µV
	lent
			f = 0.1 Hz to
	input noise voltage				0.6		0.6
			10 Hz
	Equivalent input noise
In		VIC = 0,	f = 10 kHz	25°C	2.8		2.8		fA /√ Hz
	current
	Total harmonic distor-	VO(PP) = 5 V,	AVD = 10,	25°C
THD + N	tion	f = 1 kHz,	RL = 2 kΩ,		0.013%		0.013%
	plus noise	RS = 25 Ω
B1	Unity-gain bandwidth	VI = 10 mV,	RL = 2 kΩ,	25°C	9.4		9.4		MHz
		CL = 25 pF,	See Figure 2
BOM	Maximum output-swing	VO(PP) = 4 V,	AVD = ± 1,	25°C	2.8		2.8		MHz
	bandwidth	RL = 2 kΩ ,	CL = 25 pF
φm	Phase margin at unity	VI = 10 mV,	RL = 2 kΩ,	25°C	56°		56°
	gain	CL = 25 pF,	See Figure 2

² Full range is 0°C to 70°C.

24	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265