TLE2084CN
Texas Instruments TLE2084CN, TLE2084IDW, TLE2084CDWR, TLE2084CDW, TLE2084ACN Datasheet
...
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182A – FEBRUARY 1997 – REVISED MARCH 2000
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
D
Direct Upgrades to TL05x, TL07x, and
TL08x BiFET Operational Amplifiers
D
Greater Than 2× Bandwidth (10 MHz) and
3× Slew Rate (45 V/µs) Than TL08x
D
On-Chip Offset Voltage Trimming for
Improved DC Performance
D
Wider Supply Rails Increase Dynamic
Signal Range to ±19 V
description
The TLE208x series of JFET-input operational amplifiers more than double the bandwidth and triple the slew
rate of the TL07x and TL08x families of BiFET operational amplifiers. The TLE208x also have wider
supply-voltage rails, increasing the dynamic-signal range for BiFET circuits to ±19 V. On-chip zener trimming
of offset voltage yields precision grades for greater accuracy in dc-coupled applications. The TLE208x are
pin-compatible with lower performance BiFET operational amplifiers for ease in improving performance in
existing designs.
BiFET operational amplifiers offer the inherently higher input impedance of the JFET -input transistors, without
sacrificing the output drive associated with bipolar amplifiers. This makes these amplifiers better suited for
interfacing with high-impedance sensors or very low level ac signals. They also feature inherently better ac
response than bipolar or CMOS devices having comparable power consumption.
Because BiFET operational amplifiers are designed for use with dual power supplies, care must be taken to
observe common-mode input-voltage limits and output voltage swing when operating from a single supply . DC
biasing of the input signal is required and loads should be terminated to a virtual ground node at mid-supply.
T exas Instruments TLE2426 integrated virtual ground generator is useful when operating BiFET amplifiers from
single supplies.
The TLE208x are fully specified at ±15 V and ±5 V . For operation in low-voltage and/or single-supply systems,
Texas Instruments LinCMOS families of operational amplifiers (TLC- and TLV-prefix) are recommended.
When moving from BiFET to CMOS amplifiers, particular attention should be paid to slew rate and bandwidth
requirements and output loading.
For BiFET circuits requiring low noise and/or tighter dc precision, the TLE207x offer the same ac response as
the TLE208x with more stringent dc and noise specifications.
Copyright 2000, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
LinCMOS is a trademark of Texas Instruments Incorporated.
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182A – FEBRUARY 1997 – REVISED MARCH 2000
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2081 A VAILABLE OPTIONS
PACKAGED DEVICES
T
A
VIOmax
AT 25°C
SMALL
OUTLINE
(D)
CHIP
CARRIER
(FK)
CERAMIC
DIP
(JG)
PLASTIC
DIP
(P)
CHIP
FORM
(Y)
°
°
3 mV TLE2081ACD TLE2081ACP —
0°C to 70°C
6 mV TLE2081CD
— —
TLE2081CP TLE2081Y
°
°
3 mV TLE2081AMFK TLE2081AMJG
–
55°C to 125°C
6 mV
—
TLE2081MFK TLE2081MJG
— —
†
The D packages are available taped and reeled. Add R suffix to device type (e.g., TLE2081ACDR).
‡
Chip forms are tested at TA = 25°C only.
TLE2082 AVAILABLE OPTIONS
PACKAGED DEVICES
T
A
VIOmax
AT 25°C
SMALL
OUTLINE
(D)
CHIP
CARRIER
(FK)
CERAMIC
DIP
(JG)
PLASTIC
DIP
(P)
CHIP FORM
(Y)
°
°
4 mV TLE2082ACD TLE2082ACP
0°C to 70°C
7 mV TLE2082CD
— —
TLE2082CP
—
°
°
4 mV TLE2082AID TLE2082AIP
–
40°C to 85°C
7 mV TLE2082ID
— —
TLE2082IP
TLE2082Y
°
°
4 mV TLE2082AMD TLE2082AMFK TLE2082AMJG TLE2082AMP
–
55°C to 125°C
7 mV TLE2082MD TLE2082MFK TLE2082MJG TLE2082MP
—
‡
The D packages are available taped and reeled. Add R suffix to device type (e.g., TLE2082ACDR).
‡
Chip forms are tested at TA = 25°C only.
TLE2084 AVAILABLE OPTIONS
PACKAGED DEVICES
T
A
VIOmax
AT 25°C
SMALL
OUTLINE
(DW)
CHIP
CARRIER
(FK)
CERAMIC
DIP
(J)
PLASTIC
DIP
(N)
CHIP
FORM
(Y)
°
°
4 mV TLE2084ACDW TLE2084ACN —
0°C to 70°C
7 mV TLE2084CDW
— —
TLE2084CN TLE2084Y
°
°
4 mV TLE2084AMFK TLE2084AMJ
–
55°C to 125°C
7 mV
—
TLE2084MFK TLE2084MJ
— —
†
The DW packages are available taped and reeled. Add R suffix to device type (e.g., TLE2084ACDWR).
‡
Chip forms are tested at TA = 25°C only.
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182A – FEBRUARY 1997 – REVISED MARCH 2000
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
1
2
3
4
8
7
6
5
OFFSET N1
IN –
IN +
V
CC–
NC
V
CC+
OUT
OFFSET N2
3 2 1 20 19
910111213
4
5
6
7
8
18
17
16
15
14
NC
V
CC+
NC
OUT
NC
NC
IN –
NC
IN +
NC
NC
OFFSET N1
NCNCNC
NCV NC
OFFSET N2
NC
CC –
TLE2081
D, JG, OR P PACKAGE
(TOP VIEW)
TLE2081
FK PACKAGE
(TOP VIEW)
1
2
3
4
8
7
6
5
1OUT
1IN–
1IN +
V
CC–
V
CC+
2OUT
2IN–
2IN+
3212019
910111213
4
5
6
7
8
18
17
16
15
14
NC
2OUT
NC
2IN–
NC
NC
1IN–
NC
1IN+
NC
NC
1OUT
NCNCNC
NCVNC
2IN +
CC –
V
CC +
TLE2082
D, JG, OR P PACKAGE
(TOP VIEW)
TLE2082
FK PACKAGE
(TOP VIEW)
3212019
9
10 11 12 13
4
5
6
7
8
18
17
16
15
14
4IN+
NC
V
CC–
NC
3IN+
1IN+
NC
V
CC+
NC
2IN+
TLE2084
FK PACKAGE
(TOP VIEW)
1IN –
1OUT
NC
3IN –
4IN –
2 IN –
NC
3OUT
2OUT
4OUT
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
1OUT
1IN–
1IN+
V
CC+
2IN+
2IN–
2OUT
NC
4OUT
4IN–
4IN+
V
CC–
3IN+
3IN–
3OUT
NC
1
2
3
4
5
6
7
14
13
12
11
10
9
8
1OUT
1IN–
1IN+
V
CC+
2IN+
2IN–
2OUT
4OUT
4IN–
4IN+
V
CC–
3IN+
3IN–
3OUT
TLE2084
J OR N PACKAGE
(TOP VIEW)
TLE2084
DW PACKAGE
(TOP VIEW)
NC – No internal connection
symbol
+
–
OUT
IN+
IN–
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182A – FEBRUARY 1997 – REVISED MARCH 2000
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2081Y chip information
This chip, when properly assembled, displays characteristics similar to the TLE2081. Thermal compression or
ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive
epoxy or a gold-silicon preform.
BONDING PAD ASSIGNMENTS
CHIP THICKNESS: 15 TYPICAL
BONDING PADS: 4 × 4 MINIMUM
TJmax = 150°C
TOLERANCES ARE ±10%.
ALL DIMENSIONS ARE IN MILS.
PIN (4) IS INTERNALLY CONNECTED
TO BACKSIDE OF THE CHIP.
+
–
OUT
IN+
IN–
V
CC+
(6)
(3)
(2)
(5)
(1)
(7)
(4)
OFFSET N1
OFFSET N2
V
CC–
58
85
(1)
(2)
(4) (5)
(6)
(7)
(8)
(3)
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182A – FEBRUARY 1997 – REVISED MARCH 2000
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2082Y chip information
This chip, when properly assembled, displays characteristics similar to the TLE2082. Thermal compression or
ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive
epoxy or a gold-silicon preform.
BONDING PAD ASSIGNMENTS
CHIP THICKNESS: 15 TYPICAL
BONDING PADS: 4 × 4 MINIMUM
TJmax = 150°C
TOLERANCES ARE ±10%.
ALL DIMENSIONS ARE IN MILS.
PIN (4) IS INTERNALLY CONNECTED
TO BACKSIDE OF THE CHIP.
+
–
1OUT
1IN+
1IN–
V
CC+
(4)
(6)
(3)
(2)
(5)
(1)
(7)
(8)
–
+
2OUT
2IN+
2IN–
V
CC–
80
90
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182A – FEBRUARY 1997 – REVISED MARCH 2000
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2084Y chip information
This chip, when properly assembled, displays characteristics similar to the TLE2084. Thermal compression or
ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive
epoxy or a gold-silicon preform.
BONDING PAD ASSIGNMENTS
CHIP THICKNESS: 15 TYPICAL
BONDING PADS: 4 × 4 MINIMUM
TJmax = 150°C
TOLERANCES ARE ±10%.
ALL DIMENSIONS ARE IN MILS.
PIN (11) IS INTERNALLY CONNECTED
TO BACKSIDE OF THE CHIP.
+
–
1OUT
1IN+
1IN–
V
CC+
(11)
(6)
(3)
(2)
(5)
(1)
(7)
(4)
–
+
2OUT
2IN+
2IN–
V
CC–
+
–
3OUT
3IN+
3IN–
(13)
(10)
(9)
(12)
(8)
(14)
–
+
4OUT
4IN+
4IN–
(2)
(1)
(14)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
100
150
(3)
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182A – FEBRUARY 1997 – REVISED MARCH 2000
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
• 7
equivalent schematic (each channel)
Q1
IN–
IN+
Q2
D1
Q7
Q5
Q6
Q9
Q10
C2
R4
Q14
Q4
Q3
R1
Q8
R2
Q11
R3
C1
Q12
D2
Q13
Q15
Q16
Q19
Q20
Q17
R6
V
CC–
V
CC+
R8
C3
Q18
R7
R5 C4
Q21
C5
R9
R10
Q22
Q26 Q27
Q31
R14
Q29
C6Q25
Q30
R11
Q23
Q28
Q24
D3
OUT
R13
R12
OFFSET N1
(see Note A)
OFFSET N2
(see Note A)
NOTE A: OFFSET N1 AND OFFSET N2 are only availiable on the TLE2081x devices.
ACTUAL DEVICE COMPONENT COUNT
COMPONENT TLE2081 TLE2082 TLE2084
Transistors 33 57 114
Resistors 25 37 74
Diodes 8 5 10
Capacitors 6 11 22
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182A – FEBRUARY 1997 – REVISED MARCH 2000
8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
†
Supply voltage, V
CC+
(see Note 1) 19 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supply voltage, V
CC–
(see Note 1) –19 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential input voltage range, V
ID
(see Note 2) V
CC+
to V
CC–
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage range, VI (any input) V
CC+
to V
CC–
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input current, II (each input) ±1 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output current, IO (each output) ±80 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Total current into V
CC+
160 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Total current out of V
CC–
160 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Duration of short-circuit current at (or below) 25°C (see Note 3) unlimited. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous total dissipation See Dissipation Rating Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating free-air temperature range, TA: C suffix 0°C to 70°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I suffix –40°C to 85°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
M suffix –55°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range –65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Case temperature for 60 seconds: FK package 260°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: DW or N package 260°C. . . . . . . . . . . . . . .
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J package 300°C. . . . . . . . . . . . . . . . . . . . .
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between V
CC+
and V
CC–
.
2. Differential voltages are at IN+ with respect to IN–.
3. The output can be shorted to either supply. Temperatures and/or supply voltages must be limited to ensure that the maximum
dissipation rate is not exceeded.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
TA = 125°C
POWER RATING
D 725 mW 5.8 mW/°C 464 mW 377 mW 145 mW
DW 1025 mW 8.2 mW/°C 656 mW 533 mW 205 mW
FK 1375 mW 11.0 mW/°C 880 mW 715 mW 275 mW
J 1375 mW 11.0 mW/°C 880 mW 715 mW 275 mW
JG 1050 mW 8.4 mW/°C 672 mW 546 mW 210 mW
N 1150 mW 9.2 mW/°C 736 mW 598 mW 230 mW
P 1000 mW 8.0 mW/°C 640 mW 344 mW 200 mW
recommended operating conditions
C SUFFIX I SUFFIX M SUFFIX
MIN MAX MIN MAX MIN MAX
UNIT
Supply voltage, V
CC±
±2.25 ±19 ±2.25 ±19 ±2.25 ±19 V
p
V
CC±
= ±5 V –0.9 5 –0.8 5 –0.8 5
Common-mode input voltage, V
IC
V
CC±
= ±15 V –10.9 15 –10.8 15 –10.8 15
V
Operating free-air temperature, T
A
0 70 –40 85 –55 125 °C
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182A – FEBRUARY 1997 – REVISED MARCH 2000
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2081C electrical characteristics at specified free-air temperature, V
CC±
= ±5 V (unless
otherwise noted)
TLE2081C TLE2081AC
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
p
25°C 0.34 6 0.3 3
VIOInput offset voltage
VIC = 0, VO = 0,
Full range 8 5
mV
α
VIO
T emperature coef ficient
of input offset voltage
RS = 50 Ω
Full range 3.2 29 3.2 29 µV/°C
p
25°C 5 100 5 100
IIOInput offset current
V
= 0, V
= 0,
Full range 1.4 1.4
nA
p
IC
,
O
,
See Figure 4
25°C 15 175 15 175
IIBInput bias current
Full range 5 5
nA
5 5 5 5
25°C
5to5to5to5
to
Common-mode input
–1 –1.9 –1 –1.9
V
ICR
voltage range
R
S
= 50
Ω
5 5
V
Full range
5to5
to
g
–0.9 –0.9
25°C 3.8 4.1 3.8 4.1
I
O
= –
200 µA
Full range 3.7 3.7
Maximum positive peak
25°C 3.5 3.9 3.5 3.9
V
OM+
output voltage swing
I
O
= –2
mA
Full range 3.4 3.4
V
25°C 1.5 2.3 1.5 2.3
I
O
= –20
mA
Full range 1.5 1.5
25°C –3.5 –4.2 –3.5 –4.2
I
O
=
200 µA
Full range –3.4 –3.4
Maximum negative peak
25°C –3.7 –4.1 –3.7 –4.1
V
OM–
g
output voltage swing
I
O
= 2
mA
Full range –3.6 –3.6
V
25°C –1.5 –2.4 –1.5 –2.4
I
O
= 20
mA
Full range –1.5 –1.5
25°C 80 91 80 91
R
L
=
600 Ω
Full range 79 79
Large-signal differential
25°C 90 100 90 100
A
VD
gg
voltage amplification
V
O
= ± 2.3
V
R
L
= 2
kΩ
Full range 89 89
dB
25°C 95 106 95 106
R
L
= 10
kΩ
Full range 94 94
r
i
Input resistance VIC = 0 25°C
10
12
10
12
Ω
p
p
V
= 0,
Common mode 25°C 11 11
p
ciInput capacitance
IC
,
See Figure 5
Differential 25°C 2.5 2.5
pF
z
o
Open-loop output
impedance
f = 1 MHz 25°C 80 80 Ω
Common-mode V
= V
min,
25°C 70 89 70 89
CMRR
rejection ratio
IC ICR
,
VO = 0, RS = 50 Ω
Full range 68 68
dB
Supply-voltage rejection V
CC±
= ±5 V to ±15 V,
25°C 82 99 82 99
k
SVR
ygj
ratio(∆V
CC±
/∆VIO)
CC±
VO = 0, RS = 50 Ω
Full range 80 80
dB
†
Full range is 0°C to 70°C.
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182A – FEBRUARY 1997 – REVISED MARCH 2000
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2081C electrical characteristics at specified free-air temperature, V
CC±
= ±5 V (unless
otherwise noted) (continued)
TLE2081C TLE2081AC
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
pp
25°C 1.35 1.6 2.2 1.35 1.6 2.2
ICCSupply current
V
O
=
0
,
No load
Full range 2.2 2.2
mA
Short-circuit output
VID = 1 V
°
–35 –35
I
OS
current
V
O
=
0
VID = –1 V
25°C
45 45
mA
†
Full range is 0°C to 70°C.
TLE2081C operating characteristics at specified free-air temperature, V
CC±
= ±5 V
TLE2081C TLE2081AC
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
25°C 35 35
SR+ Positive slew rate
V
O(PP)
= ±2.3 V,
Full
range
23 23
V/µs
A
VD
= –1,
R
L
= 2 kΩ,
C
= 100 pF
, See
Figure 1
25°C 38 38
SR– Negative slew rate
C
L
=
100 F,See Figure 1
Full
range
23 23
V/µs
AVD = –1,
2-V step,
To 10 mV
°
0.25 0.25
tsSettling time
,
RL = 1 kΩ,
CL = 100 pF
To 1 mV
25°C
0.4 0.4
µ
s
Equivalent input noise
f = 10 Hz
°
28 28
V
n
q
voltage
f = 10 kHz
25°C
11.6 11.6
n
V/√H
z
RS = 20 Ω,
f = 10 Hz to
Peak-to-peak equivalent
See Figure 3
10 kHz
°
6
6
V
N(PP)
q
input noise voltage
f = 0.1 Hz to
10 Hz
25°C
0.6 0.6
µ
V
I
n
Equivalent input noise
current
VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz
Total harmonic distortion
V
O(PP)
= 5 V, AVD = 10,
°
THD
+
N
plus noise
f
= 1 kHz,
R
L
= 2 kΩ,
RS = 25 Ω
25°C
0.013%
0.013%
V
= 10 mV, R
= 2 kΩ,
°
B1Unity-gain bandwidth
I
,
L
,
CL = 25 pF, See Figure 2
25°C
9.4
9.4
MH
z
Maximum output-swing V
= 4 V, A
= –1,
°
B
OM
g
bandwidth
O(PP)
,
VD
,
RL = 2 kΩ ,CL = 25 pF
25°C
2.8
2.8
MH
z
V
= 10 mV, R
= 2 kΩ,
°
°
°
φmPhase margin at unity gain
I
,
L
,
CL = 25 pF, See Figure 2
25°C
56°
56°
†
Full range is 0°C to 70°C.
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182A – FEBRUARY 1997 – REVISED MARCH 2000
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2081C electrical characteristics at specified free-air temperature, V
CC±
= ±15 V (unless
otherwise noted)
TLE2081C TLE2081AC
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
p
25°C 0.49 6 0.47 3
VIOInput offset voltage
VIC = 0, VO = 0,
Full range 8 5
mV
α
VIO
T emperature coef ficient
of input offset voltage
RS = 50 Ω
Full range 3.2 29 3.2 29 µV/°C
p
25°C 6 100 6 100
IIOInput offset current
V
= 0, V
= 0,
Full range 1.4 1.4
nA
p
IC
,
O
,
See Figure 4
25°C 20 175 20 175
IIBInput bias current
Full range 5 5
nA
15 15 15 15
25°C
15to15to15to15
to
Common-mode input
–11 –11.9 –11 –11.9
V
ICR
voltage range
R
S
= 50
Ω
15 15
V
Full range
15to15
to
g
–10.9 –10.9
25°C 13.8 14.1 13.8 14.1
I
O
= –
200 µA
Full range 13.7 13.7
Maximum positive peak
25°C 13.5 13.9 13.5 13.9
V
OM+
output voltage swing
I
O
= –2
mA
Full range 13.4 13.4
V
25°C 11.5 12.3 11.5 12.3
I
O
= –20
mA
Full range 11.5 11.5
25°C –13.8 –14.2 –13.8 –14.2
I
O
=
200 µA
Full range –13.7 –13.7
Maximum negative peak
25°C –13.5 –14 –13.5 –14
V
OM–
g
output voltage swing
I
O
= 2
mA
Full range –13.4 –13.4
V
25°C –11.5 –12.4 –11.5 –12.4
I
O
= 20
mA
Full range –11.5 –11.5
25°C 80 96 80 96
R
L
=
600 Ω
Full range 79 79
Large-signal differential
25°C 90 109 90 109
A
VD
gg
voltage amplification
V
O
= ± 10
V
R
L
= 2
kΩ
Full range 89 89
dB
25°C 95 118 95 118
R
L
= 10
kΩ
Full range 94 94
r
i
Input resistance VIC = 0 25°C
10
12
10
12
Ω
c
Input capacitance
VIC = 0,
Common
mode
25°C 7.5 7.5
pF
i
See Figure 5
Differential 25°C 2.5 2.5
z
o
Open-loop output
impedance
f = 1 MHz 25°C 80 80 Ω
Common-mode V
= V
min,
25°C 80 98 80 98
CMRR
rejection ratio
IC ICR
,
VO = 0, RS = 50 Ω
Full range 79 79
dB
Supply-voltage rejection V
CC±
= ±5 V to ±15 V,
25°C 82 99 82 99
k
SVR
ygj
ratio (∆V
CC±
/∆VIO)
CC±
VO = 0, RS = 50 Ω
Full range 80 81
dB
†
Full range is 0°C to 70°C.
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182A – FEBRUARY 1997 – REVISED MARCH 2000
12
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2081C electrical characteristics at specified free-air temperature, V
CC±
= ±15 V (unless
otherwise noted)
(continued)
TLE2081C TLE2081AC
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
pp
25°C 1.35 1.7 2.2 1.35 1.7 2.2
ICCSupply current
V
O
=
0
,
No load
Full range 2.2 2.2
mA
Short-circuit output
VID = 1 V
–30 –45 –30 –45
I
OS
current
V
O
=
0
VID = –1 V
25°C
30 48 30 48
m
A
†
Full range is 0°C to 70°C.
TLE2081C operating characteristics at specified free-air temperature, V
CC±
= ±15 V
TLE2081C TLE2081AC
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
25°C 30 40 30 40
SR+ Positive slew rate
V
O(PP)
= 10 V, AVD = –1,
p
Full
range
27 27
V/µs
R
L
= 2 kΩ,
C
L
=
100 pF
,
See
Figure 1
25°C 30 45 30 45
SR– Negative slew rate
See Figure 1
Full
range
27 27
V/µs
AVD = –1,
10-V step,
To 10 mV
°
0.4 0.4
tsSettling time
,
RL = 1kΩ,
CL = 100 pF
To 1 mV
25°C
1.5 1.5
µ
s
Equivalent input noise
f = 10 Hz
°
28 28
V
n
q
voltage
f = 10 kHz
25°C
11.6 11.6
n
V√H
z
RS = 20 Ω,
f = 10 Hz to
Peak-to-peak
p
S
See Figure 3
10 kHz
°
6
6
V
N(PP)
equivalent input noise
voltage
f = 0.1 Hz to
10 Hz
25°C
0.6 0.6
µ
V
Equivalent input noise
°
I
n
q
current
V
IC
= 0,
f
= 10 kHz
25°C
2.8
2.8
fA/√H
z
Total harmonic
V
O(PP)
= 20 V, AVD = 10,
°
THD
+
N
distortion plus noise
f
= 1 kHz,
R
L
= 2 kΩ,
RS = 25 Ω
25°C
0.008%
0.008%
V
= 10 mV, R
= 2 kΩ,
°
B1Unity-gain bandwidth
I
,
L
,
CL = 25 pF, See Figure 2
25°C810810
MH
z
Maximum output- V
= 20 V, A
= –1,
°
B
OM
swing bandwidth
O(PP)
,
VD
,
RL = 2 kΩ,CL = 25 pF
25°C
478
637
478
637
kH
z
Phase margin at unity VI = 10 mV, RL = 2 kΩ,
°
°
°
φ
m
gy
gain
IL
CL = 25 pF, See Figure 2
25°C
57°
57°
†
Full range is 0°C to 70°C.
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182A – FEBRUARY 1997 – REVISED MARCH 2000
13
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2081M electrical characteristics at specified free-air temperature, V
CC±
= ±5 V (unless
otherwise noted)
TLE2081M TLE2081AM
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
p
25°C 0.34 6 0.3 3
VIOInput offset voltage
VIC = 0, VO = 0,
Full range 11.2 8.2
mV
α
VIO
T emperature coef ficient of
input offset voltage
RS = 50Ω
Full range 3.2 29
∗
3.2 29∗µV/°C
p
25°C 5 100 5 100 pA
IIOInput offset current
V
= 0, V
= 0,
Full range 20 20 nA
p
IC
,
O
,
See Figure 4
25°C 15 175 15 175 pA
IIBInput bias current
Full range 65 65 nA
5 5 5 5
25°C
5to5to5to5
to
Common-mode input
–1 –1.9 –1 –1.9
V
ICR
voltage range
R
S
= 50
Ω
5 5
V
Full range
5to5
to
g
–0.8 –0.8
25°C 3.8 4.1 3.8 4.1
I
O
= –
200 µA
Full range 3.6 3.6
Maximum positive peak
25°C 3.5 3.9 3.5 3.9
V
OM+
output voltage swing
I
O
= –2
mA
Full range 3.3 3.3
V
25°C 1.5 2.3 1.5 2.3
I
O
= –20
mA
Full range 1.4 1.4
25°C –3.8 –4.2 –3.8 –4.2
I
O
=
200 µA
Full range –3.6 –3.6
Maximum negative peak
25°C –3.5 –4.1 –3.5 –4.1
V
OM–
g
output voltage swing
I
O
= 2
mA
Full range –3.3 –3.3
V
25°C –1.5 –2.4 –1.5 –2.4
I
O
= 20
mA
Full range –1.4 –1.4
25°C 80 91 80 91
R
L
=
600 Ω
Full range 78 78
Large-signal differential
25°C 90 100 90 100
A
VD
gg
voltage amplification
V
O
= ± 2.3
V
R
L
= 2
kΩ
Full range 88 88
dB
25°C 95 106 95 106
R
L
= 10
kΩ
Full range 93 93
r
i
Input resistance VIC = 0 25°C
10
12
10
12
Ω
c
Input capacitance
VIC = 0,
Common
mode
25°C 11 11
pF
i
See Figure 5
Differential 25°C 2.5 2.5
z
o
Open-loop output
impedance
f = 1 MHz 25°C 80 80 Ω
Common-mode V
= V
min,
25°C 70 89 70 89
CMRR
rejection ratio
IC ICR
,
VO = 0, RS = 50 Ω
Full range 68 68
dB
Supply-voltage rejection V
CC±
= ±5 V to ±15 V,
25°C 82 99 82 99
k
SVR
ygj
ratio (∆V
CC±
/∆VIO)
CC±
VO = 0, RS = 50 Ω
Full range 80 80
dB
∗
On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.
†
Full range is –55°C to 125°C.
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182A – FEBRUARY 1997 – REVISED MARCH 2000
14
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2081M electrical characteristics at specified free-air temperature, V
CC±
= ±5 V (unless
otherwise noted)
(continued)
TLE2081M TLE2081AM
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
pp
25°C 1.35 1.6 2.2 1.35 1.6 2.2
ICCSupply current
V
O
=
0
,
No load
Full range 2.2 2.2
mA
Short-circuit output
VID = 1 V
°
–35 –35
I
OS
current
V
O
=
0
VID = –1 V
25°C
45 45
mA
†
Full range is –55°C to 125°C.
TLE2081M operating characteristics at specified free-air temperature, V
CC±
= ±5 V
TLE2081M TLE2081AM
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
25°C 35 35
SR+ Positive slew rate
V
O(PP)
= ±2.3 V,
Full
range
20
∗
20
∗
V/µs
A
VD
= –1,
R
L
= 2 kΩ,
C
= 100 pF
, See
Figure 1
25°C 38 38
SR– Negative slew rate
C
L
=
100 F,See Figure 1
Full
range
20
∗
20
∗
V/µs
AVD = –1,
2-V step,
To 10 mV
°
0.25 0.25
tsSettling time
,
RL = 1 kΩ,
CL = 100 pF
To 1 mV
25°C
0.4 0.4
µ
s
Equivalent input noise
f = 10 Hz
°
28 28
V
n
q
voltage
f = 10 kHz
25°C
11.6 11.6
n
V/√H
z
RS = 20 Ω,
f = 10 Hz to
Peak-to-peak
p
S
See Figure 3
10 kHz
°
6
6
V
N(PP)
equivalent input noise
f = 0.1 Hz to
25°CµV
voltage
10 Hz
0.6
0.6
I
n
Equivalent input noise
current
VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz
Total harmonic
V
O(PP)
= 5 V, AVD = 10,
°
THD
+
N
distortion plus noise
f
= 1 kHz,
R
L
=
2 kΩ
,
RS = 25 Ω
25°C
0.013%
0.013%
V
= 10 mV, R
= 2 kΩ,
°
B1Unity-gain bandwidth
I
,
L
,
CL = 25 pF, See Figure 2
25°C
9.4
9.4
MH
z
Maximum output-swing V
= 4 V, A
= –1,
°
B
OM
g
bandwidth
O(PP)
,
VD
,
RL = 2 kΩ ,CL = 25 pF
25°C
2.8
2.8
MH
z
Phase margin at unity VI = 10 mV, RL = 2 kΩ,
°
°
°
φ
m
gy
gain
IL
CL = 25 pF, See Figure 2
25°C
56°
56°
∗On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.
†
Full range is –55°C to 125°C.
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182A – FEBRUARY 1997 – REVISED MARCH 2000
15
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2081M electrical characteristics at specified free-air temperature, V
CC±
= ±15 V (unless
otherwise noted)
TLE2081M TLE2081AM
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
p
25°C 0.49 6 0.47 3
VIOInput offset voltage
VIC = 0, VO = 0,
Full range 1 1.2 8.2
mV
α
VIO
T emperature coef ficient
of input offset voltage
RS = 50 Ω
Full range 3.2
29
∗
3.2
29
∗
µV/°C
p
25°C 6 100 6 100 pA
IIOInput offset current
V
= 0, V
= 0,
Full range 20 20 nA
p
IC
,
O
,
See Figure 4
25°C 20 175 20 175 pA
IIBInput bias current
Full range 65 65 nA
15 15 15 15
25°C
15to15to15to15
to
Common-mode input
–11 –11.9 –11 –11.9
V
ICR
voltage range
R
S
= 50
Ω
15 15
V
Full range
15to15
to
g
–10.8 –10.8
25°C 13.8 14.1 13.8 14.1
I
O
= –
200 µA
Full range 13.6 13.6
Maximum positive peak
25°C 13.5 13.9 13.5 13.9
V
OM+
output voltage swing
I
O
= –2
mA
Full range 13.3 13.3
V
25°C 11.5 12.3 11.5 12.3
I
O
= –20
mA
Full range 1 1.4 1 1.4
25°C –13.8 –14.2 –13.8 –14.2
I
O
=
200 µA
Full range –13.6 –13.6
Maximum negative peak
25°C –13.5 –14 –13.5 –14
V
OM–
g
output voltage swing
I
O
= 2
mA
Full range –13.3 –13.3
V
25°C –11.5 –12.4 –11.5 –12.4
I
O
= 20
mA
Full range –11.4 –11.4
25°C 80 96 80 96
R
L
=
600 Ω
Full range 78 78
Large-signal differential
25°C 90 109 90 109
A
VD
gg
voltage amplification
V
O
= ± 10
V
R
L
= 2
kΩ
Full range 88 88
dB
25°C 95 118 95 118
R
L
= 10
kΩ
Full range 93 93
r
i
Input resistance VIC = 0 25°C
10
12
10
12
Ω
c
Input capacitance
VIC = 0,
Common
mode
25°C 7.5 7.5
pF
i
See Figure 5
Differential 25°C 2.5 2.5
z
o
Open-loop output
impedance
f = 1 MHz 25°C 80 80 Ω
Common-mode V
= V
min,
25°C 80 98 80 98
CMRR
rejection ratio
IC ICR
,
VO = 0, RS = 50 Ω
Full range 78 78
dB
Supply-voltage rejection V
CC±
= ±5 V to ±15 V,
25°C 82 99 82 99
k
SVR
ygj
ratio (∆V
CC±
/∆VIO)
CC±
VO = 0, RS = 50 Ω
Full range 80 80
dB
∗
On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.
†
Full range is –55°C to 125°C.
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182A – FEBRUARY 1997 – REVISED MARCH 2000
16
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2081M electrical characteristics at specified free-air temperature, V
CC±
= ±15 V (unless
otherwise noted)(continued)
TLE2081M TLE2081AM
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
pp
25°C 1.35 1.7 2.2 1.35 1.7 2.2
ICCSupply current
V
O
=
0
,
No load
Full range 2.2 2.2
mA
Short-circuit output
VID = 1 V
–30 –45 –30 –45
I
OS
current
V
O
=
0
VID = –1 V
25°C
30 48 30 48
m
A
†
Full range is –55°C to 125°C.
TLE2081M operating characteristics at specified free-air temperature, V
CC±
= ±15 V
TLE2081M TLE2081AM
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
25°C 30 40 30 40
SR+ Positive slew rate
V
O(PP)
= 10 V,
Full
range
22 22
V/µs
A
VD
= –1,
R
L
= 2 kΩ,
C
= 100 pF
, See
Figure 1
25°C 30 45 30 45
SR– Negative slew rate
C
L
=
100 F,See Figure 1
Full
range
22 22
V/µs
AVD = –1,
10-V step,
To 10 mV
°
0.4 0.4
tsSettling time
,
RL = 1kΩ,
CL = 100 pF
To 1 mV
25°C
1.5 1.5
µ
s
Equivalent input noise
f = 10 Hz
°
28 28
V
n
q
voltage
f = 10 kHz
25°C
11.6 11.6
n
V/√H
z
RS = 20 Ω,
f = 10 Hz to
Peak-to-peak
p
S
See Figure 3
10 kHz
°
6
6
V
N(PP)
equivalent input noise
f = 0.1 Hz to
25°CµV
voltage
10 Hz
0.6
0.6
I
n
Equivalent input noise
current
VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz
Total harmonic distortion
V
O(PP)
= 20 V, AVD = 10,
°
THD
+
N
plus noise
f
= 1 kHz,
R
L
= 2 kΩ,
RS = 25 Ω
25°C
0.008%
0.008%
V
= 10 mV, R
= 2 kΩ,
°
B1Unity-gain bandwidth
I
,
L
,
CL = 25 pF, See Figure 2
25°C
8
∗
10
8
∗
10
MH
z
Maximum output-swing V
= 20 V, A
= –1,
°
B
OM
g
bandwidth
O(PP)
,
VD
,
RL = 2 kΩ,CL = 25 pF
25°C
478
∗
637
478
∗
637
kH
z
Phase margin at unity VI = 10 mV, RL = 2 kΩ,
°
°
°
φ
m
gy
gain
IL
CL = 25 pF, See Figure 2
25°C
57°
57°
∗
On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.
†
Full range is –55°C to 125°C.
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182A – FEBRUARY 1997 – REVISED MARCH 2000
17
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2081Y electrical characteristics at V
CC±
= ±15 V, TA = 25°C
TLE2081Y
PARAMETER
TEST CONDITIONS
MIN TYP MAX
UNIT
V
IO
Input offset voltage VIC = 0, VO = 0, RS = 50 Ω 0.49 6 mV
I
IO
Input offset current
6 100
p
I
IB
Input bias current
V
IC
=
0
,
V
O
=
0,See Figure 4
20 175
pA
15 15
V
ICR
Common-mode input voltage range RS = 50 Ω
15to15
to
V
ICR
gg
S
–11 11.9
IO = –200 µA 13.8 14.1
V
OM+
Maximum positive peak
p
IO = –2 mA 13.5 13.9
V
out ut voltage swing
IO = –20 mA 11.5 12.3
IO = 200 µA –13.8 –14.2
V
OM–
Maximum negative peak output
IO = 2 mA –13.5 –14
V
voltage swing
IO = 20 mA –11.5 –12.4
RL = 600 Ω 80 96
A
VD
Large-signal differential voltage
p
VO = ± 10 V
RL = 2 kΩ 90 109
dB
am lification
RL = 10 kΩ 95 118
r
i
Input resistance VIC = 0
10
12
Ω
p
p
Common mode 7.5
p
ciInput capacitance
V
IC
= 0,
See Figure 5
Differential 2.5
pF
z
o
Open-loop output impedance f = 1 MHz 80 Ω
CMRR Common-mode rejection ratio VIC = V
ICR
min, VO = 0, RS = 50 Ω 80 98 dB
k
SVR
Supply-voltage rejection ratio
(∆V
CC±
/∆VIO)
V
CC±
= ±5 V to ±15 V, VO = 0, RS = 50 Ω 82 99 dB
I
CC
Supply current VO = 0, No load 1.35 1.7 2.2 mA
VID = 1 V –30 –45
IOSShort-ci
rcuit output curren
t
V
O
=
0
VID = –1 V
30 48
m
A
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182A – FEBRUARY 1997 – REVISED MARCH 2000
18
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2082C electrical characteristics at specified free-air temperature, V
CC±
= ±5 V (unless
otherwise noted)
TLE2082C TLE2082AC
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
p
25°C 0.9 6 0.65 4
VIOInput offset voltage
VIC = 0, VO = 0,
Full range 8.1 5.1
mV
α
VIO
T emperature coef ficient
of input offset voltage
RS = 50 Ω
Full range 2.3 25 2.3 25 µV/°C
p
25°C 5 100 5 100 pA
IIOInput offset current
V
= 0, V
= 0,
Full range 1.4 1.4 nA
p
IC
,
O
,
See Figure 4
25°C 15 175 15 175 pA
IIBInput bias current
Full range 5 5 nA
5 5 5 5
25°C
to to to to
Common-mode input
–1 –1.9 –1 –1.9
V
ICR
voltage range
R
S
= 50
Ω
5 5
V
gg
Full range
to to
g
–0.9 –0.9
25°C 3.8 4.1 3.8 4.1
I
O
= –
200 µA
Full range 3.7 3.7
Maximum positive peak
25°C 3.5 3.9 3.5 3.9
V
OM+
output voltage swing
I
O
= –2
mA
Full range 3.4 3.4
V
25°C 1.5 2.3 1.5 2.3
I
O
= –20
mA
Full range 1.5 1.5
25°C –3.8 –4.2 –3.8 –4.2
I
O
=
200 µA
Full range –3.7 –3.7
Maximum negative peak
25°C –3.5 –4.1 –3.5 –4.1
V
OM–
g
output voltage swing
I
O
= 2
mA
Full range –3.4 –3.4
V
25°C –1.5 –2.4 –1.5 –2.4
I
O
= 20
mA
Full range –1.5 –1.5
25°C 80 91 80 91
R
L
=
600 Ω
Full range 79 79
Large-signal differential
25°C 90 100 90 100
A
VD
gg
voltage amplification
V
O
= ± 2.3
V
R
L
= 2
kΩ
Full range 89 89
dB
25°C 95 106 95 106
R
L
= 10
kΩ
Full range 94 94
r
i
Input resistance VIC = 0 25°C
10
12
10
12
Ω
Input
Common mode
25°C 11 11
p
c
i
In ut
capacitance
Differential
V
IC
= 0,
See Figure 5
25°C 2.5 2.5
pF
z
o
Open-loop output impedance f = 1 MHz 25°C 80 80 Ω
V
= V
min,
25°C 70 89 70 89
CMRR
Common-mode rejection ratio
IC ICR
,
VO = 0, RS = 50 Ω
Full range 68 68
dB
Supply-voltage rejection V
= ±5 V to ±15 V,
25°C 82 99 82 99
k
SVR
ygj
ratio(∆V
CC±
/∆VIO)
CC±
,
VO = 0, RS = 50 Ω
Full range 80 80
dB
Supply current
25°C 2.7 2.9 3.9 2.7 2.9 3.9
I
CC
y
(both channels)
V
O
= 0,
No load
Full range 3.9 3.9
mA
†
Full range is 0°C to 70°C.
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182A – FEBRUARY 1997 – REVISED MARCH 2000
19
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2082C electrical characteristics at specified free-air temperature, V
CC±
= ±5 V (unless
otherwise noted)
(continued)
TLE2082C TLE2082AC
PARAMETER
TEST CONDITIONS
T
A
MIN TYP MAX MIN TYP MAX
UNIT
Crosstalk attenuation VIC = 0, RL = 2 kΩ 25°C 120 120 dB
p
VID = 1 V
°
–35 –35
IOSShort-circuit output current
V
O
=
0
VID = –1 V
25°C
45 45
mA
TLE2082C operating characteristics at specified free-air temperature, V
CC±
= ±5 V
TLE2082C TLE2082AC
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
25°C 35 35
SR+ Positive slew rate
V
O(PP)
= ±2.3 V,
Full
range
22 22
V/µs
A
VD
= –1,
R
L
= 2 kΩ,
C
= 100 pF,See Figure 1
25°C 38 38
SR– Negative slew rate
C
L
100 F,See Figure 1
Full
range
22 22
V/µs
AVD = –1,
2-V step,
To 10 mV
°
0.25 0.25
tsSettling time
,
RL = 1 kΩ,
CL = 100 pF
To 1 mV
25°C
0.4 0.4
µ
s
Equivalent input noise
f = 10 Hz
°
28 28
V
n
q
voltage
f = 10 kHz
25°C
11.6 11.6
n
V/√H
z
RS = 20 Ω,
f = 10 Hz to
Peak-to-peak equivalent
See Figure 3
10 kHz
°
6
6
V
N(PP)
q
input noise voltage
f = 0.1Hz to
10 Hz
25°C
0.6 0.6
µ
V
I
n
Equivalent input noise
current
VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz
Total harmonic distortion
V
O(PP)
= 5 V, AVD = 10,
°
THD
+
N
plus noise
f
= 1 kHz,
R
L
=
2 kΩ
,
RS = 25 Ω
25°C
0.013%
0.013%
V
= 10 mV, R
= 2 kΩ,
°
B1Unity-gain bandwidth
I
,
L
,
CL = 25 pF, See Figure 2
25°C
9.4
9.4
MH
z
Maximum output-swing
V
O(PP
)
= 4 V, AVD = –1,
°
B
OM
g
bandwidth
O(PP) VD
RL = 2 kΩ ,CL = 25 pF
25°C
2.8
2.8
MH
z
Phase margin at unity VI = 10 mV, RL = 2 kΩ,
°
°
°
φ
m
gy
gain
IL
CL = 25 pF, See Figure 2
25°C
56°
56°
†
Full range is 0°C to 70°C.
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182A – FEBRUARY 1997 – REVISED MARCH 2000
20
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2082C electrical characteristics at specified free-air temperature, V
CC±
= ±15 V (unless
otherwise noted)
TLE2082C TLE2082AC
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
p
25°C 1.1 7 0.7 4
VIOInput offset voltage
VIC = 0, VO = 0,
Full range 8.1 5.1
mV
α
VIO
T emperature coef ficient
of input offset voltage
RS = 50 Ω
Full range 2.4 25 2.4 25 µV/°C
p
25°C 6 100 6 100 pA
IIOInput offset current
V
= 0, V
= 0,
Full range 1.4 1.4 nA
p
IC
,
O
,
See Figure 4
25°C 20 175 20 175 pA
IIBInput bias current
Full range 5 5 nA
15 15 15 15
25°C
to to to to
Common-mode input
–11 –11.9 –11 –11.9
V
ICR
voltage range
R
S
= 50
Ω
15 15
V
gg
Full range
to to
g
–10.9 –10.9
25°C 13.8 14.1 13.8 14.1
I
O
= –
200 µA
Full range 13.6 13.6
Maximum positive peak
25°C 13.5 13.9 13.5 13.9
V
OM+
output voltage swing
I
O
= –2
mA
Full range 13.4 13.4
V
25°C 11.5 12.3 11.5 12.3
I
O
= –20
mA
Full range 11.5 11.5
25°C –13.8 –14.2 –13.8 –14.2
I
O
=
200 µA
Full range –13.7 –13.7
Maximum negative peak
25°C –13.5 –14 –13.5 –14
V
OM–
g
output voltage swing
I
O
= 2
mA
Full range –13.4 –13.4
V
25°C –11.5 –12.4 –11.5 –12.4
I
O
= 20
mA
Full range –11.5 –11.5
25°C 80 96 80 96
R
L
=
600 Ω
Full range 79 79
Large-signal differential
25°C 90 109 90 109
A
VD
gg
voltage amplification
V
O
= ± 10
V
R
L
= 2
kΩ
Full range 89 89
dB
25°C 95 118 95 118
R
L
= 10
kΩ
Full range 94 94
r
i
Input resistance VIC = 0 25°C
10
12
10
12
Ω
c
Input
p
Common
mode
VIC = 0,
25°C 7.5 7.5
pF
i
ca acitance
Differential
See Figure 5
25°C 2.5 2.5
z
o
Open-loop output
impedance
f = 1 MHz 25°C 80 80 Ω
Common-mode V
= V
min,
25°C 80 98 80 98
CMRR
rejection ratio
IC ICR
,
VO = 0, RS = 50 Ω
Full range 79 79
dB
Supply-voltage rejection V
= ±5 V to ±15 V,
25°C 82 99 82 99
k
SVR
ygj
ratio (∆V
CC±
/∆VIO)
CC±
,
VO = 0, RS = 50 Ω
Full range 81 81
dB
†
Full range is 0°C to 70°C.
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182A – FEBRUARY 1997 – REVISED MARCH 2000
21
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2082C electrical characteristics at specified free-air temperature, V
CC±
= ±15 V (unless
otherwise noted)
(continued)
TLE2082C TLE2082AC
PARAMETER
TEST CONDITIONS
T
A
MIN TYP MAX MIN TYP MAX
UNIT
pp
25°C 2.7 3.1 3.9 2.7 3.1 3.9
I
CC
Supply current
(both channels)
VO = 0, No load
Full
range
3.9 3.9
mA
Crosstalk attenuation VIC = 0, RL = 2 kΩ 25°C 120 120 dB
p
VID = 1 V
°
–30 –45 –30 –45
IOSShort-circuit output current
V
O
=
0
VID = –1 V
25°C
30 48 30 48
mA
TLE2082C operating characteristics at specified free-air temperature, V
CC±
= ±15 V
TLE2082C TLE2082AC
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
25°C 28 40 28 40
SR+ Positive slew rate
V
O(PP)
= 10 V, AVD = –1,
p
Full
range
25 25
V/µs
R
L
=
2 kΩ
,
C
L
=
100 pF
,
See Fi
g
ure 1
25°C 30 45 30 45
SR– Negative slew rate
See Figure 1
Full
range
25 25
V/µs
AVD = –1,
10-V step,
To 10 mV
°
0.4 0.4
tsSettling time
,
RL = 1kΩ,
CL = 100 pF
To 1 mV
25°C
1.5 1.5
µ
s
Equivalent input noise
f = 10 Hz
°
28 28
V
n
q
voltage
f = 10 kHz
25°C
11.6 11.6
n
V/√H
z
R
= 20 Ω, f = 10 Hz to
Peak-to-peak equivalent
S
,
See Figure 3 10 kHz
6
6
V
N(PP)
Peak to eak equivalent
input noise voltage
f = 0.1Hz to
25°CµV
10 Hz
0.6
0.6
I
n
Equivalent input noise
current
VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz
Total harmonic distortion
V
O(PP)
= 20 V, AVD = 10,
THD
+
N
plus noise
f
= 1 kHz,
R
L
= 2 kΩ,
RS = 25 Ω
25°C
0.008%
0.008%
V
= 10 mV, R
= 2 kΩ,
°
B1Unity-gain bandwidth
I
,
L
,
CL = 25 pF, See Figure 2
25°C810810
MH
z
Maximum output-swing
V
O(PP
)
= 20 V, AVD = –1,
°
B
OM
g
bandwidth
O(PP) VD
RL = 2 kΩ,CL = 25 pF
25°C
478
637
478
637
kH
z
Phase margin at V
= 10 mV, R
= 2 kΩ,
°
°
°
φ
m
g
unity gain
I
,
L
,
CL = 25 pF, See Figure 2
25°C
57°
57°
†
Full range is 0°C to 70°C.
Loading...