Texas Instruments TLE2144CDW, TLE2144AMJB, TLE2144AMFKB, TLE2144AIN, TLE2144ACN Datasheet

							TLE214x, TLE214xA, TLE214xY
							EXCALIBUR LOW-NOISE HIGH-SPEED
							PRECISION OPERATIONAL AMPLIFIERS
							SLOS183A ± FEBRUARY 1997 ± REVISED MARCH 1998
D	Low Noise					D Single or Split Supply . . . 4 V to 44 V
	10 Hz . . . 15 nV/√	Hz				D	Fast Settling Time
	1 kHz . . . 10.5 nV/√		Hz				340 ns to 0.1%
D	10000-pF Load Capability						400 ns to 0.01%
D 20-mA Min Short-Circuit Output Current						D	Saturation Recovery . . . 150 ns
D 27-V/µs Min Slew Rate						D	Large Output Swing
D High Gain-Bandwidth Product . . . 5.9 MHz							VCC ± +0.1 V to VCC + ± 1 V

DLow VIO . . . 500 µV Max at 25°C

description

The TLE214x and TLE214xA devices are high-performance, internally compensated operational amplifiers built using Texas Instruments complementary bipolar Excalibur process. The TLE214xA is a tighter offset voltage grade of the TLE214x. Both are pin-compatible upgrades to standard industry products.

The design incorporates an input stage that simultaneously achieves low audio-band noise of 10.5 nV/√ Hz with a 10-Hz 1/f corner and symmetrical 40-V/µs slew rate typically with loads up to 800 pF. The resulting low distortion and high power bandwidth are important in high-fidelity audio applications. A fast settling time of 340 ns to 0.1% of a 10-V step with a 2-kΩ/100-pF load is useful in fast actuator/positioning drivers. Under similar test conditions, settling time to 0.01% is 400 ns.

The devices are stable with capacitive loads up to 10 nF, although the 6-MHz bandwidth decreases to 1.8 MHz at this high loading level. As such, the TLE214x and TLE214xA are useful for low-droop sample-and-holds and direct buffering of long cables, including 4-mA to 20-mA current loops.

The special design also exhibits an improved insensitivity to inherent integrated circuit component mismatches as is evidenced by a 500-µV maximum offset voltage and 1.7-µV/°C typical drift. Minimum common-mode rejection ratio and supply-voltage rejection ratio are 85 dB and 90 dB, respectively.

Device performance is relatively independent of supply voltage over the ±2-V to ±22-V range. Inputs can operate between VCC ± ± 0.3 to VCC + ± 1.8 V without inducing phase reversal, although excessive input current may flow out of each input exceeding the lower common-mode input range. The all-npn output stage provides a nearly rail-to-rail output swing of VCC ± ± 0.1 to VCC + ± 1 V under light current-loading conditions. The device can sustain shorts to either supply since output current is internally limited, but care must be taken to ensure that maximum package power dissipation is not exceeded.

Both versions can also be used as comparators. Differential inputs of VCC ± can be maintained without damage to the device. Open-loop propagation delay with TTL supply levels is typically 200 ns. This gives a good indication as to output stage saturation recovery when the device is driven beyond the limits of recommended output swing.

Both the TLE214x and TLE214xA are available in a wide variety of packages, including both the industry-standard 8-pin small-outline version and chip form for high-density system applications. The C-suffix devices are characterized for operation from 0°C to 70°C, I-suffix devices from ±40°C to 105°C, and M-suffix devices over the full military temperature range of ±55°C to 125°C.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.

Copyright 1998, Texas Instruments Incorporated

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

1

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A ± FEBRUARY 1997 ± REVISED MARCH 1998

TLE2141 AVAILABLE OPTIONS

PACKAGED DEVICES

CHIP

VIOmax

TA

SMALL OUT-

CHIP CARRIER

CERAMIC DIP

PLASTIC DIP

FORM³

AT 25°C

LINE²

(FK)

(JG)

(P)

(Y)

(D)

0°C to 70°C

500 V

TLE2141ACD

Ð

Ð

TLE2141ACP

Ð

900

V

TLE2141CD

TLE2141CP

± 40°C to 105°C

500 V

TLE2141AID

Ð

Ð

TLE2141AIP

TLE2141Y

900

V

TLE2141ID

TLE2141IP

± 55°C to 125°C

500 V

TLE2141AMD

TLE2141AMFK

TLE2141AMJG

TLE2141AMP

Ð

900

V

TLE2141MD

TLE2141MFK

TLE2141MJG

TLE2141MP

² The D packages are available taped and reeled. Add R suffix to device type (e.g., TLE2141ACDR).

³ Chip forms are tested at T

= 25°C only.

A

TLE2142 AVAILABLE OPTIONS

PACKAGED DEVICES

CHIP

V

max

SMALL

CHIP

CERAMIC

PLASTIC

³

FORM§

T

IO

OUTLINE²

CARRIER

DIP

DIP

TSSOP

A

°

(PW)

(Y)

AT 25 C

(D)

(FK)

(JG)

(P)

0°C to 70°C

750 V

TLE2142ACD

Ð

Ð

TLE2142ACP

Ð

Ð

1200

V

TLE2142CD

Ð

Ð

TLE2142CP

TLE2142CPWLE

±40°C to 105°C

750 V

TLE2142AID

Ð

Ð

TLC2142AIP

Ð

TLE2142Y

1200

V

TLE2142ID

Ð

Ð

TLC2142IP

Ð

±55°C to 125°C

750 V

TLE2142AMD

TLE2142AMFK

TLE2142AMJG

TLC2142AMP

Ð

Ð

1200

V

TLE2142MD

TLE2142MFK

TLE2142MJG

TLC2142MP

Ð

² The D packages are available taped and reeled. Add R suffix to device type (e.g., TLC2142ACDR).

³ The PW packages are available left-ended taped and reeled. Add LE the suffix to device type (e.g., TLC2142CPWLE).

§ Chip forms are tested at T = 25°C only.

A

TLE2144 AVAILABLE OPTIONS

V

max

PACKAGED DEVICES

CHIP FORM³

TA

IO

SMALL OUTLINE²

CHIP CARRIER

CERAMIC DIP

PLASTIC DIP

AT 25°C

(Y)

(DW)

(FK)

(J)

(N)

0°C to 70°C

1.5 mV

Ð

Ð

Ð

TLE2144ACN

Ð

2.4 mV

TLE2144CDW

Ð

Ð

TLE2144CN

± 40°C to 105°C

1.5 mV

Ð

Ð

Ð

TLE2144AIN

TLE2144Y

2.4 mV

TLE2144IDW

Ð

Ð

TLE2144IN

± 55°C to 125°C

1.5 mV

Ð

TLE2144AMFK

TLE2144AMJ

TLE2144AMN

Ð

2.5 mV

TLE2144MDW

TLE2144MFK

TLE2144MJ

TLE2144MN

² The DW packages are available taped and reeled. Add R suffix to device type (e.g., TLE2144CDWR). ³ Chip forms are tested at TA = 25°C only.

2	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TLE214x, TLE214xA, TLE214xY EXCALIBUR LOW-NOISE HIGH-SPEED PRECISION OPERATIONAL AMPLIFIERS

SLOS183A ± FEBRUARY 1997 ± REVISED MARCH 1998

TLE2141

D, JG, OR P PACKAGE

(TOP VIEW)

OFFSET N1		1	8		NC
IN±		2	7		VCC +
IN+
		3	6		OUT
VCC ±		4	5		OFFSET N2

		TLE2141
	FK PACKAGE
		(TOP VIEW)
	NC	OFFSET N1	NC	NC NC
NC	3	2	1	20 19	NC
	4			18
IN±	5			17	VCC +
NC	6			16	NC
IN+	7			15	OUT
NC	8			14	NC
	9	10 11 12 13

		NC	CC± NC		N2 NC
			V		OFFSET
		TLE2144
	DW PACKAGE
		(TOP VIEW)
1OUT					4OUT
		1	16
1IN±		2	15		4IN±
1IN+		3	14		4IN+
VCC +		4	13		VCC ±
2IN+		5	12		3IN+
2IN±		6	11		3IN±
2OUT		7	10		3OUT
NC		8	9		NC

NC ± No internal connection

		TLE2142							TLE2142
	PW PACKAGE						D, JG, OR P PACKAGE
		(TOP VIEW)
									(TOP VIEW)
NC						NC	1OUT					VCC +
		1	16						1	8
1OUT						VCC+
		2	15				1IN±		2	7		2OUT
1OUT		3	14			VCC+	1IN+		3	6		2IN±
1IN±		4	13			2OUT	VCC ±		4	5		2IN+
1IN+		5	12			2IN±
VCC ±		6	11			2IN+			TLE2142
VCC ±		7	10			2IN+
						NC	FK PACKAGE
NC		8	9
								(TOP VIEW)

	NC	1OUT	NC	CC +	NC
				V
NC	3	2	1	20 19		NC
	4				18
1IN±	5				17	2OUT
NC	6				16	NC
1IN +	7				15	2IN±
NC	8				14	NC
	9	10 11 12 13
	NC	V	NC	2IN+	NC
		CC±

TLE2144

J OR N PACKAGE

(TOP VIEW)

1OUT		1	14		4OUT
1IN±		2	13		4IN±
1IN+		3	12		4IN+
VCC +		4	11		VCC ±
2IN+		5	10		3IN+
2IN±		6	9		3IN±
2OUT		7	8		3OUT

TLE2144

FK PACKAGE (TOP VIEW)

	1IN ±	1OUT	NC	4OUT	4IN ±
1IN+	3	2	1	20 19		4IN+
	4				18
NC	5				17	NC
VCC +	6				16	VCC ±
NC	7				15	NC
2IN+	8				14	3IN+
	9	10 11 12 13
	2IN ±	2OUT	NC	3OUT	3IN ±

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

3

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A ± FEBRUARY 1997 ± REVISED MARCH 1998

symbol

OFFSET N1

(see Note A)

IN + +

OUT

IN ± ±

OFFSET N2

(see Note A)

NOTES: A. OFFSET N1 AND OFFSET N2 are only availiable on the

TLE2241x devices.

TLE2141Y chip information

This chip, when properly assembled, displays characteristics similar to the TLE2141. Thermal compression or ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive epoxy or a gold-silicon preform.

BONDING PAD ASSIGNMENTS

(7)

64

(1)

(2)

(6)

	(1)					VCC+
	OFFSET N1							(7)
	(3)
					+
	IN +									(6)
	(2)				±						OUT
(5)	IN ±								(4)
	(5)
	OFFSET N2
						VCC ±

CHIP THICKNESS: 15 TYPICAL

BONDING PADS: 4 × 4 MINIMUM

TJmax = 150°C

(4)TOLERANCES ARE ± 10%.

ALL DIMENSIONS ARE IN MILS.

(3)

65

4	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A ± FEBRUARY 1997 ± REVISED MARCH 1998

TLE2142Y chip information

This chip, when properly assembled, displays characteristics similar to the TLE2142. Thermal compression or ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive epoxy or a gold-silicon preform.

BONDING PAD ASSIGNMENTS

							(2)	(1)	(8)		(7)
			90				(3)				(6)
								(4)			(5)
									80

		VCC+
	(3)			(8)
1IN +		+
					(1)	1OUT
1IN ±	(2)	±
					(5)	2IN +
		+
	(7)
2OUT
					(6)
				±		2IN ±
				(4)
		VCC ±

CHIP THICKNESS: 15 TYPICAL BONDING PADS: 4 × 4 MINIMUM TJmax = 150°C

TOLERANCES ARE ± 10%.

ALL DIMENSIONS ARE IN MILS.

PIN 4 IS INTERNALLY CONNECTED TO BACKSIDE OF CHIP.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

5

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A ± FEBRUARY 1997 ± REVISED MARCH 1998

TLE2144Y chip information

This chip, when properly assembled, displays characteristics similar to the TLE2144. Thermal compression or ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive epoxy or a gold-silicon preform.

																																																				BONDING PAD ASSIGNMENTS																																																																																															VCC +
																																																																																																																																																				(4)
										(12)															(11)																																																																																		(10)																																						1IN +	(3)	+
										(13)																																																																																																	(9)																																											(1)
																																																																																																																																																	1IN ±	(2)	±				1OUT
																																																																																																																																																		(5)
																																																																																																																																																	2IN +		+			(7)
										(14)																																																																																																	(8)																																						2IN ±	(6)	±				2OUT
																																																																																																																																																		(10)
																																																																																																																																																	3IN +		+
					103																																																																																																																																																	(8)
																																																																																																																																																	3IN ±	(9)	±				3OUT
										(1)																																																																																																	(7)																																							(12)
																																																																																																																																																	4IN +		+			(14)
																																																																																																																																																	4IN ±	(13)	±	(11)			4OUT
										(2)																																																																																																	(6)																																								VCC ±
										(3)															(4)																																																																																		(5)																																						CHIP THICKNESS:
																																																																																																																																																	15 TYPICAL
																																																																										140																																																																							BONDING PADS:
																																																																																																																																																	4 × 4 MINIMUM
																																																																																																																																																	TJmax = 150°C
																																																																																																																																																	TOLERANCES ARE ± 10%.
																																																																																																																																																	ALL DIMENSIONS ARE IN MILS.

6	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

equivalent schematic

VCC +

R1

R4

R7

R14

R18

R19

R21

Q3

Q5 Q8

Q13

Q22

Q30

Q10

Q26

R24

D1

Q34

Q37

D2

Q23

Q27

D8

R23

R3

R2

R6

R8

D3

D4

Q36

POST

IN ±

Q6

Q11

R15

R17

OUT

Q1

Q4

Q14

Q15

R13

BOXOFFICE

IN +

R9

R16

655303•

Q9

C3

Q25

Q28

Q16

Q31

7 75265 TEXAS DALLAS,

Q2

Q19

C4

D6

Q35

AMPLIFIERSOPERATIONALPRECISION

SPEED-HIGHNOISE-LOW EXCALIBUR

TLE214xYTLE214xA,TLE214x,

C1

Q24

1998MARCHREVISED±1997FEBRUARY± SLOS183A

R10

C2

Q32

Q18

Q20

D7

R22

OFFSET N1

Q7

Q12

Q17

Q21

Q29

Q33

(see Note A)

R5

R11

R12

D5

OFFSET N2

R20

(see Note A)

VCC ±

NOTE A: OFFSET N1 AND OFFSET N2 are only availiable on the TLE2241x devices.

ACTUAL DEVICE COMPONENT COUNT

COMPONENT

TLE2241

TLE2242

TLE2244

Transistors

46

65

130

Resistors

24

43

86

Diodes

8

14

28

Capacitors

4

8

16

Epi-FET

1

1

2

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A ± FEBRUARY 1997 ± REVISED MARCH 1998

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)²

Supply voltage, VCC + (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . . . .	. . . . . . . 22 V
Supply voltage, VCC ± . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . . . .	. . . . . . ±22 V
Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . . . . .	. . . . ± 44 V
Input voltage range, VI (any input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . VCC + to VCC ± ± 0.3 V
Input current, II (each input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . . . . .	. . . . ± 1 mA
Output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . . . . .	. . . ± 80 mA
Total current into VCC+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . . . . .	. . . . 80 mA
Total current out of VCC± . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . . . . .	. . . . 80 mA
Duration of short-circuit current at (or below) 25°C (see Note 3) . . . . . . . . . . . . .	. . . . . . . . . . . . . . .	. . unlimited
Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	See Dissipation Rating Table
Operating free-air temperature range, TA: C suffix . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . . . .	0°C to 70°C
I suffix . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . ±40°C to 105°C
M suffix . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . ±55°C to 125°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . ±65°C to 150°C
Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . . . . .	. . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D, DW, N, P, or PW package		. . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J or JG package . . . . . . . . . . . .		. . . . 300°C

²Stresses beyond those listed under ªabsolute maximum ratingsº may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under ªrecommended operating conditionsº is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

NOTES: 1.	All voltage values, except differential voltages, are with respect to the midpoint between VCC+ and VCC ±.
2.	Differential voltages are at IN+ with respect to IN ±. Excessive current flows if input is brought below VCC ± ± 0.3 V.

3.The output may be shorted to either supply. Temperature and /or supply voltages must be limited to ensure that the maximum dissipation rating is not exceeded.

DISSIPATION RATING TABLE

	PACKAGE	TA ≤ 25°C	DERATING FACTOR	TA = 70°C	TA = 105°C	TA = 125°C
		POWER RATING	ABOVE TA = 25°C	POWER RATING	POWER RATING	POWER RATING
	D	725 mW	5.8 mW/°C	464 mW	261 mW	145 mW
	DW	1025 mW	8.2 mW/°C	656 mW	369 mW	205 mW
	FK	1375 mW	11.0 mW/°C	880 mW	495 mW	275 mW
	J	1375 mW	11.0 mW/°C	880 mW	495 mW	275 mW
	JG	1050 mW	8.4 mW/°C	672 mW	378 mW	210 mW
	N	1150 mW	9.2 mW/°C	736 mW	414 mW	230 mW
	P	1000 mW	8.0 mW/°C	640 mW	360 mW	200 mW
	PW	525 mW	4.2 mW/°C	336 mW	Ð	Ð

recommended operating conditions

				C SUFFIX		I SUFFIX		M SUFFIX		UNIT
				MIN	MAX	MIN	MAX	MIN	MAX
	Supply voltage, VCC ±			± 2	± 22	± 2	± 22	± 2	± 22	V
	Common-mode input voltage, VIC	VCC = 5 V		0	2.9	0	2.7	0	2.7	V
		VCC ± =	± 15 V	± 15	12.9	± 15	12.7	± 15	12.7
	Operating free-air temperature, TA			0	70	± 40	105	± 55	125	°C

8	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A ± FEBRUARY 1997 ± REVISED MARCH 1998

TLE2141C electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted)

	PARAMETER	TEST CONDITIONS		T ²	TLE2141C			TLE2141AC			UNIT
				A	MIN	TYP	MAX	MIN	TYP	MAX
VIO	Input offset voltage			25°C		225	1400		200	1000	µV
				Full range			1700			1300
αVIO	Temperature coefficient of			Full range		1.7			1.7		µV/°C
	input offset voltage	VO = 2.5 V	RS = 50 Ω,
IIO	Input offset current	VIC = 2.5 V		25°C		8	100		8	100	nA
				Full range			150			150
IIB	Input bias current			25°C		± 0.8	± 2		± 0.8	± 2	µA
				Full range			± 2.1			± 2.1
				25°C	0	± 0.3		0	± 0.3
					to	to		to	to
VICR	Common-mode input	RS = 50 Ω			3	3.2		3	3.2		V
	voltage range				0			0
				Full range	to			to
					2.9			2.9
		IOH = ±150 µA		25°C	3.9	4.1		3.9	4.1
				Full range	3.8			3.8
VOH	High-level output voltage	IOH = ±1.5 mA		25°C	3.8	4		3.8	4		V
				Full range	3.7			3.7
		IOH = ±15 mA		25°C	3.2	3.7		3.2	3.7
				Full range	3.2			3.2
		IOL = 150 µA		25°C		75	125		75	125
				Full range			150			150	mV
VOL	Low-level output voltage	IOL = 1.5 mA		25°C		150	225		150	225
				Full range			250			250
		IOL = 15 mA		25°C		1.2	1.6		1.2	1.6	V
				Full range			1.7			1.7
AVD	Large-signal differential	VCC = ± 2.5 V,	RL = 2 kΩ,	25°C	50	220		50	220		V/mV
	voltage amplification	VO = 1 V to ± 1.5 V		Full range	25			25
ri	Input resistance			25°C		70			70		MΩ
ci	Input capacitance			25°C		2.5			2.5		pF
zo	Open-loop output	f = 1 MHz		25°C		30			30		Ω
	impedance
CMRR	Common-mode rejection	VIC = VICRmin, RS = 50 Ω		25°C	85	118		85	118		dB
	ratio			Full range	80			80
kSVR	Supply-voltage rejection	VCC ± = ± 2.5 V to ± 15 V,		25°C	90	106		90	106		dB
	ratio ( VCC ± / VIO)	RS = 50 Ω		Full range	85			85
ICC	Supply current	VO = 2.5 V,	No load,	25°C		3.4	4.4		3.4	4.4	mA
		VIC = 2.5 V		Full range			4.6			4.6

² Full range is 0°C to 70°C.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

9

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A ± FEBRUARY 1997 ± REVISED MARCH 1998

TLE2141C operating characteristics, VCC = 5 V, TA = 25°C

PARAMETER

TEST CONDITIONS

TLE2141C

TLE2141AC

UNIT

MIN

TYP MAX

MIN

TYP

MAX

SR +

Positive slew rate

A

= ± 1,

R

= 2 kΩ,² ,

45

45

VD

L

V/µs

SR ±

Negative slew rate

42

42

CL = 500 pF²,

ts

Settling time

AVD = ± 1,

To 0.1%

0.16

0.16

µs

2.5-V step

To 0.01%

0.22

0.22

Vn

Equivalent input noise voltage

RS = 20 Ω,

f = 10 Hz

15

15

nV/√ Hz

RS = 20 Ω,

f = 1 kHz

10.5

10.5

VN(PP)

Peak-to-peak equivalent input

f = 0.1 Hz to 1 Hz

0.48

0.48

µV

noise voltage

f = 0.1 Hz to 10 Hz

0.51

0.51

In

Equivalent input noise current

f = 10 Hz

1.92

1.92

pA/√

Hz

f = 1 kHz

0.5

0.5

THD + N

Total harmonic distortion

VO = 1 V to 3 V,

²

0.0052%

0.0052%

plus noise

RL = 2 kΩ ,

AVD = 2,

f = 10 kHz

B1

Unity-gain bandwidth

RL = 2 kΩ² ,

CL = 100 pF²

5.9

5.9

MHz

Gain-bandwidth product

RL = 2 kΩ² ,

CL = 100 pF² ,

5.8

5.8

MHz

f = 100 kHz

BOM

Maximum output-swing

VO(PP) = 2 V,

RL = 2 kΩ² ,

660

660

kHz

bandwidth

A

= 1,

C

L

= 100 pF²

VD

φ

Phase margin at unity gain

R

L

= 2 kΩ² ,

C

L

= 100 pF²

57°

57°

m

² RL and CL terminated to 2.5 V.

10	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A ± FEBRUARY 1997 ± REVISED MARCH 1998

TLE2141C electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted)

	PARAMETER	TEST CONDITIONS		T ²	TLE2141C			TLE2141AC			UNIT
				A	MIN	TYP	MAX	MIN	TYP	MAX
VIO	Input offset voltage			25°C		200	900		175	500	µV
				Full range			1300			800
αVIO	Temperature coefficient			Full range		1.7			1.7		µV/°C
	of input offset voltage	VIC = 0,	RS = 50 Ω,
IIO	Input offset current	VO = 0		25°C		7	100		7	100	nA
				Full range			150			150
IIB	Input bias current			25°C		± 0.7	± 1.5		± 0.7	± 1.5	µA
				Full range			± 1.6			± 1.6
				25°C	± 15	± 15.3		± 15	± 15.3
					to	to		to	to
VICR	Common-mode input	RS = 50 Ω			13	13.2		13	13.2		V
	voltage range				± 15	± 15.3		± 15	± 15.3
				Full range	to	to		to	to
					12.9	13.1		12.9	13.1
		IO = ±150 µA		25°C	13.8	14.1		13.8	14.1
				Full range	13.7			13.7
VOM +	Maximum positive peak	IO = ±1.5 mA		25°C	13.7	14		13.7	14		V
	output voltage swing			Full range	13.6			13.6
		IO = ±15 mA		25°C	13.1	13.7		13.1	13.7
				Full range	13			13
		IO = 150 µA		25°C	± 14.7	± 14.9		± 14.7	± 14.9
				Full range	± 14.6			± 14.6
	Maximum negative
VOM ±		IO = 1.5 mA		25°C	± 14.5	± 14.8		± 14.5	± 14.8		V
	peak output voltage
				Full range	± 14.4			± 14.4
	swing
		IO = 15 mA		25°C	± 13.4	± 13.8		± 13.4	± 13.8
				Full range	± 13.3			± 13.3
AVD	Large-signal differential	VO = ± 10 V		25°C	100	450		100	450		V/mV
	voltage amplification			Full range	75			75
ri	Input resistance	RL = 2 kΩ		25°C		65			65		MΩ
ci	Input capacitance			25°C		2.5			2.5		pF
zo	Open-loop output	f = 1 MHz		25°C		30			30		Ω
	impedance
CMRR	Common-mode	VIC = VICRmin,	RS = 50 Ω	25°C	85	108		85	108		dB
	rejection ratio			Full range	80			80
kSVR	Supply-voltage	VCC ± = ± 2.5 V to ± 15 V,		25°C	90	106		90	106		dB
	rejection ratio
		RS = 50 Ω		Full range	85			85
	( VCC ± / VIO)
IOS	Short-circuit output	VO = 0	VID = 1 V	25°C	± 25	± 50		± 25	± 50		mA
	current		VID = ± 1 V		20	31		20	31
ICC	Supply current	VO = 0,	No load	25°C		3.5	4.5		3.5	4.5	mA
				Full range			4.7			4.7

² Full range is 0°C to 70°C.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

11

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A ± FEBRUARY 1997 ± REVISED MARCH 1998

TLE2141C operating characteristics, VCC ± = ±15 V, TA = 25°C

	PARAMETER	TEST CONDITIONS		TLE2141C		TLE2141AC			UNIT
				MIN	TYP MAX	MIN	TYP	MAX
SR +	Positive slew rate	AVD = ± 1,	RL = 2 kΩ,	27	45	27	45		V/µs
SR ±	Negative slew rate			27	42	27	42
		CL = 500 pF
ts	Settling time	AVD = ± 1,	To 0.1%		0.34		0.34		µs
		10-V step	To 0.01%		0.4		0.4
Vn	Equivalent input noise voltage	RS = 20 Ω,	f = 10 Hz		15		15
									nV/√ Hz
		RS = 20 Ω,	f = 1 kHz		10.5		10.5
VN(PP)	Peak-to-peak equivalent input	f = 0.1 Hz to 1 Hz			0.48		0.48		µV
	noise voltage	f = 0.1 Hz to 10 Hz			0.51		0.51
In	Equivalent input noise current	f = 10 Hz			1.89		1.89		pA/√
										Hz
		f = 1 kHz			0.47		0.47
THD + N	Total harmonic distortion plus	VO(PP) = 20 V,	RL = 2 kΩ,		0.01%		0.01%
	noise	AVD = 10,	f = 10 kHz
B1	Unity-gain bandwidth	RL = 2 kΩ,	CL = 100 pF		6		6		MHz
	Gain-bandwidth product	RL = 2 kΩ,	CL = 100 pF,		5.9		5.9		MHz
		f = 100 kHz
BOM	Maximum output-swing	VO(PP) = 20 V,	RL = 2 kΩ,		668		668		kHz
	bandwidth	AVD = 1,	CL = 100 pF
φm	Phase margin at unity gain	RL = 2 kΩ,	CL = 100 pF		58°		58°

12	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A ± FEBRUARY 1997 ± REVISED MARCH 1998

TLE2142C electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted)

	PARAMETER	TEST CONDITIONS		T ²	TLE2142C			TLE2142AC			UNIT
				A	MIN	TYP	MAX	MIN	TYP	MAX
VIO	Input offset voltage			25°C		220	1900		200	1500	µV
				Full range			2200			1800
αVIO	Temperature coefficient of			Full range		1.7			1.7		µV/°C
	input offset voltage	VO = 2.5 V,	RS = 50 Ω,
IIO	Input offset current	VIC = 2.5 V		25°C		8	100		8	100	nA
				Full range			150			150
IIB	Input bias current			25°C		± 0.8	± 2		± 0.8	± 2	µA
				Full range			± 2.1			± 2.1
				25°C	0	± 0.3		0	± 0.3
					to	to		to	to
VICR	Common-mode input	RS = 50 Ω			3	3.2		3	3.2		V
	voltage range				0			0
				Full range	to			to
					2.9			2.9
		IOH = ±150 µA		25°C	3.9	4.1		3.9	4.1
				Full range	3.8			3.8
VOH	High-level output voltage	IOH = ±1.5 mA		25°C	3.8	4		3.8	4		V
				Full range	3.7			3.7
		IOH = ±15 mA		25°C	3.4	3.7		3.4	3.7
				Full range	3.4			3.4
		IOL = 150 µA		25°C		75	125		75	125
				Full range			150			150	mV
VOL	Low-level output voltage	IOL = 1.5 mA		25°C		150	225		150	225
				Full range			250			250
		IOL = 15 mA		25°C		1.2	1.4		1.2	1.4	V
				Full range			1.5			1.5
AVD	Large-signal differential	VCC = ± 2.5 V,	RL = 2 kΩ,	25°C	50	220		50	220		V/mV
	voltage amplification	VO = 1 V to ± 1.5 V		Full range	25			25
ri	Input resistance			25°C		70			70		MΩ
ci	Input capacitance			25°C		2.5			2.5		pF
zo	Open-loop output	f = 1 MHz		25°C		30			30		Ω
	impedance
CMRR	Common-mode	VIC = VICRmin, RS = 50 Ω		25°C	85	118		85	118		dB
	rejection ratio			Full range	80			80
kSVR	Supply-voltage rejection	VCC ± = ± 2.5 V to ± 15 V,		25°C	90	106		90	106		dB
	ratio ( VCC ± / VIO)	RS = 50 Ω		Full range	85			85
ICC	Supply current	VO = 2.5 V,	No load,	25°C		6.6	8.8		6.6	8.8	mA
		VIC = 2.5 V		Full range			9.2			9.2

² Full range is 0°C to 70°C.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

13

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A ± FEBRUARY 1997 ± REVISED MARCH 1998

TLE2142C operating characteristics, VCC = 5 V, TA = 25°C

PARAMETER

TEST CONDITIONS

TLE2142C

TLE2142AC

UNIT

MIN TYP MAX

MIN TYP

MAX

SR +

Positive slew rate

A

= ± 1,

R

= 2 kΩ² ,

45

45

VD

L

V/µs

SR ±

Negative slew rate

CL = 500 pF

42

42

ts

Settling time

AVD = ± 1,

To 0.1%

0.16

0.16

µs

2.5-V step

To 0.01%

0.22

0.22

Vn

Equivalent input noise voltage

RS = 20 Ω,

f = 10 Hz

15

15

nV/√ Hz

RS = 20 Ω,

f = 1 kHz

10.5

10.5

VN(PP)

Peak-to-peak equivalent

f = 0.1 Hz to 1 Hz

0.48

0.48

µV

input noise voltage

f = 0.1 Hz to 10 Hz

0.51

0.51

In

Equivalent input noise current

f = 10 Hz

1.92

1.92

pA/√

Hz

f = 1 kHz

0.5

0.5

THD + N

Total harmonic distortion plus

VO = 1 V to 3 V,

RL = 2 kΩ² ,

0.0052%

0.0052%

noise

AVD = 2,

f = 10 kHz

B1

Unity-gain bandwidth

RL = 2 kΩ² ,

CL = 100 pF

5.9

5.9

MHz

Gain-bandwidth product

RL = 2 kΩ² ,

CL = 100 pF,

5.8

5.8

MHz

f = 100 kHz

BOM

Maximum output-swing

VO(PP) = 2 V,

RL = 2 kΩ² ,

660

660

kHz

bandwidth

AVD = 1,

CL = 100 pF

φ

Phase margin at unity gain

R

L

= 2 kΩ² ,

C

L

= 100 pF

57°

57°

m

² RL terminates at 2.5 V.

14	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A ± FEBRUARY 1997 ± REVISED MARCH 1998

TLE2142C electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted)

PARAMETER

TEST CONDITIONS

T ²

TLE2142C

TLE2142AC

UNIT

A

MIN

TYP

MAX

MIN

TYP

MAX

VIO

Input offset voltage

25°C

290

1200

275

750

µV

Full range

1600

1200

αVIO

Temperature coefficient of

Full range

1.7

1.7

µV/°C

input offset voltage

VIC = 0,

RS = 50 Ω,

IIO

Input offset current

VO = 0

25°C

7

100

7

100

nA

Full range

150

150

IIB

Input bias current

25°C

± 0.7

± 1.5

± 0.7

± 1.5

µA

Full range

± 1.6

± 1.6

25°C

± 15

± 15.3

± 15

± 15.3

to

to

to

to

VICR

Common-mode input

RS = 50 Ω

13

13.2

13

13.2

V

voltage range

± 15

± 15.3

± 15

± 15.3

Full range

to

to

to

to

12.9

13.1

12.9

13.1

IO = ±150 µA

25°C

13.8

14.1

13.8

14.1

Full range

13.7

13.7

VOM +

Maximum positive peak

IO = ±1.5 mA

25°C

13.7

14

13.7

14

V

output voltage swing

Full range

13.6

13.6

IO = ±15 mA

25°C

13.3

13.7

13.3

13.7

Full range

13.2

13.2

IO = 150 µA

25°C

± 14.7

± 14.9

± 14.7

± 14.9

Full range

± 14.6

± 14.6

VOM ±

Maximum negative peak

IO = 1.5 mA

25°C

± 14.5

± 14.8

± 14.5

± 14.8

V

output voltage swing

Full range

± 14.4

± 14.4

IO = 15 mA

25°C

± 13.4

± 13.8

± 13.4

± 13.8

Full range

± 13.3

± 13.3

AVD

Large-signal differential

VO = ± 10 V

25°C

100

450

100

450

V/mV

voltage amplification

Full range

75

75

ri

Input resistance

RL = 2 kΩ

25°C

65

65

MΩ

ci

Input capacitance

25°C

2.5

2.5

pF

zo

Open-loop output

f = 1 MHz

25°C

30

30

Ω

impedance

CMRR

Common-mode

VIC = VICRmin,

25°C

85

108

85

108

dB

rejection ratio

RS = 50 Ω

Full range

80

80

kSVR

Supply-voltage rejection

VCC ± = ± 2.5 V to ± 15 V,

25°C

90

106

90

106

dB

ratio ( VCC ± / VIO)

RS = 50 Ω

Full range

85

85

IOS

Short-circuit output current

VO = 0

VID = 1 V

25°C

± 25

± 50

± 25

± 50

mA

VID = ± 1 V

20

31

20

31

ICC

Supply current

VO = 0,

No load

25°C

6.9

9

6.9

9

mA

Full range

9.4

9.4

² Full range is 0°C to 70°C.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

15

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A ± FEBRUARY 1997 ± REVISED MARCH 1998

TLE2142C operating characteristics, VCC ± = ±15 V, TA = 25°C

	PARAMETER	TEST CONDITIONS			TLE2142C	TLE2142AC			UNIT
				MIN	TYP MAX	MIN	TYP	MAX
SR +	Positive slew rate	AVD = ± 1,	RL = 2 kΩ,	27	45	27	45		V/µs
SR ±	Negative slew rate			27	42	27	42
		CL = 500 pF
ts	Settling time	AVD = ± 1,	To 0.1%		0.34		0.34		µs
		10-V step	To 0.01%		0.4		0.4
Vn	Equivalent input noise voltage	RS = 20 Ω,	f = 10 Hz		15		15
									nV/√ Hz
		RS = 20 Ω,	f = 1 kHz		10.5		10.5
VN(PP)	Peak-to-peak equivalent input	f = 0.1 Hz to 1 Hz			0.48		0.48		µV
	noise voltage	f = 0.1 Hz to 10 Hz			0.51		0.51
In	Equivalent input noise current	f = 10 Hz			1.89		1.89		pA/√
										Hz
		f = 1 kHz			0.47		0.47
THD + N	Total harmonic distortion plus	VO(PP) = 20 V,	RL = 2 kΩ,		0.01%		0.01%
	noise	AVD = 10,	f = 10 kHz
B1	Unity-gain bandwidth	RL = 2 kΩ,	CL = 100 pF		6		6		MHz
	Gain-bandwidth product	RL = 2 kΩ,,	CL = 100 pF,		5.9		5.9		MHz
		f =100 kHz
BOM	Maximum output-swing	VO(PP) = 20 V,	RL = 2 kΩ,		668		668		kHz
	bandwidth	AVD = 1,	CL = 100 pF
φm	Phase margin at unity gain	RL = 2 kΩ,	CL = 100 pF		58°		58°

16	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A ± FEBRUARY 1997 ± REVISED MARCH 1998

TLE2144C electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted)

	PARAMETER	TEST CONDITIONS		T ²	TLE2144C			TLE2144AC			UNIT
				A	MIN	TYP	MAX	MIN	TYP	MAX
VIO	Input offset voltage			25°C		0.5	3.8		0.5	3	mV
				Full range			4.4			3.6
αVIO	Temperature coefficient			Full range		1.7			1.7		µV/°C
	of input offset voltage	VO = 2.5 V,
			RS = 50 Ω,
IIO	Input offset current	VIC = 2.5 V		25°C		8	100		8	100	nA
				Full range			150			150
IIB	Input bias current			25°C		± 0.8	± 2		± 0.8	± 2	µA
				Full range			± 2.1			± 2.1
					0	± 0.3		0	± 0.3
				25°C	to	to		to	to
VICR	Common-mode input	RS = 50 Ω			3	3.2		3	3.2		V
	voltage range				0			0
				Full range	to			to
					2.9			2.9
		IOH = ±150 µA		25°C	3.9	4.1		3.9	4.1
				Full range	3.8			3.8
VOH	High-level output	IOH = ±1.5 mA		25°C	3.8	4		3.8	4		V
	voltage			Full range	3.7			3.7
		IOH = ±15 mA		25°C	3.4	3.7		3.4	3.7
				Full range	3.4			3.4
		IOL = 150 µA		25°C		75	125		75	125
				Full range			150			150	mV
VOL	Low-level output	IOL = 1.5 mA		25°C		150	225		150	225
	voltage			Full range			250			250
		IOL = 15 mA		25°C		1.2	1.6		1.2	1.6	V
				Full range			1.7			1.7
AVD	Large-signal differential	VCC = ± 2.5 V,	RL = 2 kΩ,	25°C	50	95		50	95		V/mV
	voltage amplification	VO = 1 V to ± 1.5 V		Full range	25			25
ri	Input resistance			25°C		70			70		MΩ
ci	Input capacitance			25°C		2.5			2.5		pF
zo	Open-loop output	f = 1 MHz		25°C		30			30		Ω
	impedance
CMRR	Common-mode	VIC = VICRmin,	RS = 50 Ω	25°C	85	118		85	118		dB
	rejection ratio			Full range	80			80
	Supply-voltage	VCC ± = ± 2.5 V to ± 15 V,		25°C	90	106		90	106
kSVR	rejection ratio										dB
		RS = 50 Ω		Full range	85			85
	( VCC ± / VIO)
ICC	Supply current	VO = 2.5 V,	No load,	25°C		13.2	17.6		13.2	17.6	mA
		VIC = 2.5 V		Full range			18.5			18.5

² Full range is 0°C to 70°C.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

17

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A ± FEBRUARY 1997 ± REVISED MARCH 1998

TLE2144C operating characteristics, VCC = 5 V, TA = 25°C

PARAMETER

TEST CONDITIONS

TLE2144C

TLE2144AC

UNIT

MIN

TYP MAX

MIN TYP

MAX

SR +

Positive slew rate

AVD = ± 1,

RL = 2 kΩ² ,

45

45

V/µs

SR ±

Negative slew rate

CL = 500 pF

42

42

ts

Settling time

AVD = ± 1,

To 0.1%

0.16

0.16

µs

2.5-V step

To 0.01%

0.22

0.22

Vn

Equivalent input

RS = 20 Ω,

f = 10 Hz

15

15

nV/√ Hz

noise voltage

RS = 20 Ω,

f = 1 kHz

10.5

10.5

VN(PP)

Peak-to-peak equivalent

f = 0.1 Hz to 1 Hz

0.48

0.48

µV

input noise voltage

f = 0.1 Hz to 10 Hz

0.51

0.51

In

Equivalent input

f = 10 Hz

1.92

1.92

pA/√ Hz

noise current

f = 1 kHz

0.5

0.5

THD + N

Total harmonic distortion plus

VO = 1 V to 3 V,

RL

= 2 kΩ² ,

0.0052%

0.0052%

noise

AVD = 2,

f = 10 kHz

B1

Unity-gain bandwidth

RL = 2 kΩ² ,

CL = 100 pF

5.9

5.9

MHz

Gain-bandwidth product

RL = 2 kΩ² ,

CL = 100 pF,

5.8

5.8

MHz

f = 100 kHz

Maximum output-swing

V

= 2 V,

R

L

= 2 kΩ² ,

BOM

bandwidth

O(PP)

660

660

kHz

AVD = 1,

CL = 100 pF

φ

Phase margin at unity gain

R

L

= 2 kΩ² ,

C

L

= 100 pF

57°

57°

m

² RL terminates at 2.5 V

18	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A ± FEBRUARY 1997 ± REVISED MARCH 1998

TLE2144C electrical characteristics at specified free-air temperature, VCC ± = ±15 V (unless otherwise noted)

	PARAMETER	TEST CONDITIONS		T ²	TLE2144C			TLE2144AC			UNIT
				A	MIN	TYP	MAX	MIN	TYP	MAX
VIO	Input offset voltage			25°C		0.6	2.4		0.5	1.5	mV
				Full range			3.2			2.4
αVIO	Temperature coefficient			Full range		1.7			1.7		µV/°C
	of input offset voltage	VIC = 0,	RS = 50 Ω,
IIO	Input offset current	VO = 0		25°C		7	100		7	100	nA
				Full range			150			150
IIB	Input bias current			25°C		± 0.7	± 1.5		± 0.7	± 1.5	µA
				Full range			± 1.6			± 1.6
					± 15	± 15.3		± 15	± 15.3
				25°C	to	to		to	to
VICR	Common-mode input	RS = 50 Ω			13	13.2		13	13.2		V
	voltage range				± 15	± 15.3		± 15	± 15
				Full range	to	to		to	to
					12.9	13.1		12.9	13.1
		IO = ±150 µA		25°C	13.8	14.1		13.8	14.1
				Full range	13.7			13.7
VOM +	Maximum positive peak	IO = ±1.5 mA		25°C	13.7	14		13.7	14		V
	output voltage swing			Full range	13.6			13.6
		IO = ±15 mA		25°C	13.1	13.7		13.1	13.7
				Full range	13			13
		IO = 150 µA		25°C	± 14.7	± 14.9		± 14.7	± 14.9
				Full range	± 14.6			± 14.6
	Maximum negative
				25°C	± 14.5	± 14.8		± 14.5	± 14.8
VOM ±	peak output voltage	IO = 1.5 mA									V
				Full range	± 14.4			± 14.4
	swing
		IO = 15 mA		25°C	± 13.4	± 13.8		± 13.4	± 13.8
				Full range	± 13.3			± 13.3
AVD	Large-signal differential	VO = ± 10 V		25°C	100	170		100	170		V/mV
	voltage amplification			Full range	75			75
ri	Input resistance	RL = 2 kΩ		25°C		65			65		MΩ
ci	Input capacitance			25°C		2.5			2.5		pF
zo	Open-loop output	f = 1 MHz		25°C		30			30		Ω
	impedance
CMRR	Common-mode	VIC = VICRmin,	RS = 50 Ω	25°C	85	108		85	108		dB
	rejection ratio			Full range	80			80
	Supply-voltage	VCC ± = ± 2.5 V to ± 15 V,		25°C	90	106		90	106
kSVR	rejection ratio										dB
		RS = 50 Ω		Full range	85			85
	( VCC ± / VIO)
IOS	Short-circuit output	VO = 0	VID = 1 V	25°C	± 25	± 50		± 25	± 50		mA
	current		VID = ± 1 V		20	31		20	31
ICC	Supply current	VO = 0,	No load	25°C		13.8	18		13.8	18	mA
				Full range			18.8			18.8

² Full range is 0°C to 70°C.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

19

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A ± FEBRUARY 1997 ± REVISED MARCH 1998

TLE2144C operating characteristics, VCC ± = ±15 V, TA = 25°C

	PARAMETER	TEST CONDITIONS			TLE2144C		TLE2144AC		UNIT
				MIN	TYP MAX	MIN	TYP	MAX
SR +	Positive slew rate	AVD = ± 1,	RL = 2 kΩ,	27	45	27	45		V/µs
SR ±	Negative slew rate	CL = 500 pF		27	42	27	42
ts	Settling time	AVD = ± 1,	To 0.1%		0.34		0.34		µs
		10-V step	To 0.01%		0.4		0.4
Vn	Equivalent input noise voltage	RS = 20 Ω,	f = 10 Hz		15		15
									nV/√ Hz
		RS = 20 Ω,	f = 1 kHz		10.5		10.5
VN(PP)	Peak-to-peak equivalent input	f = 0.1 Hz to 1 Hz			0.48		0.48		µV
	noise voltage	f = 0.1 Hz to 10 Hz			0.51		0.51
In	Equivalent input noise current	f = 10 Hz			1.89		1.89		pA/√
										Hz
		f = 1 kHz			0.47		0.47
THD + N	Total harmonic distortion plus	VO(PP) = 20 V,	RL = 2 kΩ,		0.01%		0.01%
	noise	AVD = 10,	f = 10 kHz
B1	Unity-gain bandwidth	RL = 2 kΩ,	CL = 100 pF		6		6		MHz
	Gain-bandwidth product	RL = 2 kΩ,	CL = 100 pF,		5.9		5.9		MHz
		f = 100 kHz
BOM	Maximum output-swing	VO(PP) = 20 V,	RL = 2 kΩ,		668		668		kHz
	bandwidth	AVD = 1,	CL = 100 pF
φm	Phase margin at unity gain	RL = 2 kΩ,	CL = 100 pF		58°		58°

20	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

TLE214x, TLE214xA, TLE214xY

EXCALIBUR LOW-NOISE HIGH-SPEED

PRECISION OPERATIONAL AMPLIFIERS

SLOS183A ± FEBRUARY 1997 ± REVISED MARCH 1998

TLE2141I electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted)

	PARAMETER	TEST CONDITIONS		T ²		TLE2141I		TLE2141AI			UNIT
				A	MIN	TYP	MAX	MIN	TYP	MAX
VIO	Input offset voltage			25°C		225	1400		200	1000	µV
				Full range			1900			1500
αVIO	Temperature coefficient			Full range		1.7			1.7		µV/°C
	of input offset voltage	VO = 2.5 V,	RS = 50 Ω,
IIO	Input offset current	VIC = 2.5 V		25°C		8	100		8	100	nA
				Full range			200			200
IIB	Input bias current			25°C		± 0.8	± 2		± 0.8	± 2	µA
				Full range			± 2.2			± 2.2
				25°C	0	± 0.3		0	± 0.3
					to	to		to	to
VICR	Common-mode input	RS = 50 Ω			3	3.2		3	3.2		V
	voltage range				0	± 0.3		0	± 0.3
				Full range	to	to		to	to
					2.7	2.9		2.7	2.9
		IOH = ± 150 µA			3.9	4.1		3.9	4.1
		IOH = ± 1.5 mA		25°C	3.8	4		3.8	4
VOH	High-level output voltage	IOH = ± 15 mA			3.2	3.7		3.2	3.7		V
		IOH = ± 100 µA			3.8			3.8
		IOH = ± 1 mA		Full range	3.7			3.7
		IOH = ± 10 mA			3.3			3.3
		IOL = 150 µA				75	125		75	125	mV
		IOL = 1.5 µA		25°C		150	225		150	225
VOL	Low-level output voltage	IOL = 15 mA				1.2	1.6		1.2	1.6	V
		IOL = 100 µA					175			175	mV
		IOL = 1 mA		Full range			225			225
		IOL = 10 mA					1.4			1.4	V
AVD	Large-signal differential	VCC = ± 2.5 V,	RL = 2 kΩ,	25°C	50	220		50	220		V/mV
	voltage amplification	VO = 1 V to ± 1.5 V		Full range	10			10
ri	Input resistance			25°C		70			70		MΩ
ci	Input capacitance			25°C		2.5			2.5		pF
zo	Open-loop output	f = 1 MHz		25°C		30			30		Ω
	impedance
CMRR	Common-mode	VIC = VICRmin, RS = 50 Ω		25°C	85	118		85	118		dB
	rejection ratio			Full range	80			80
kSVR	Supply-voltage rejection	VCC ± = ± 2.5 V to ± 15 V,		25°C	90	106		90	106		dB
	ratio ( VCC ± / VIO)	RS = 50 Ω		Full range	85			85
ICC	Supply current	VO = 2.5 V,	No load,	25°C		3.4	4.4		3.4	4.4	mA
		VIC = 2.5 V		Full range			4.6			4.6

² Full range is ± 40°C to 105°C.

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

21