Texas Instruments SN74AC563DW, SN74AC563DWR, SN74AC563N, SN74AC563PWLE, SN74AC563PWR Datasheet

				SN54AC563, SN74AC563
	OCTAL D-TYPE TRANSPARENT LATCHES
				WITH 3-STATE OUTPUTS
	SCAS552A ± NOVEMBER 1995 ± REVISED MAY 1996
D 3-State Inverting Outputs Drive Bus Lines	SN54AC563 . . . J OR W PACKAGE
Directly	SN74AC563 . . . DB, DW, N, OR PW PACKAGE
D Full Parallel Access for Loading				(TOP VIEW)
D Flow-Through Architecture to Optimize						VCC
		OE		1	20
PCB Layout
		1D		2	19	1Q
D EPIC (Enhanced-Performance Implanted		2D
				3	18	2Q
		3D
				4	17	3Q
CMOS) 1- m Process		4D
D Package Options Include Plastic				5	16	4Q
		5D
Small-Outline (DW), Shrink Small-Outline				6	15	5Q
		6D
(DB), Thin Shrink Small-Outline (PW),				7	14	6Q
		7D
Ceramic Chip Carriers (FK) and				8	13	7Q
		8D
Flatpacks (W), and Standard Plastic (N) and				9	12	8Q
Ceramic (J) DIPs	GND			10	11	LE

description

The 'AC563 are octal D-type transparent latches with 3-state outputs. When the latch-enable (LE) input is high, the Q outputs follow the complements of the data (D) inputs. When LE is taken low, the Q outputs are latched at the inverse logic levels set up at the D inputs.

A buffered output-enable (OE) input can be used to place the eight outputs in either a normal logic state (high or low logic levels) or the high-imped- ance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and increased drive provide the capability to drive bus lines without need for interface or pullup components.

SN54AC563 . . . FK PACKAGE

(TOP VIEW)

	2D	1D	OE	CC	1Q
				V
3D	3	2	1	20 19		2Q
	4				18
4D	5				17	3Q
5D	6				16	4Q
6D	7				15	5Q
7D	8				14	6Q
	9	10 11 12 13
	8D	GND	CLK	8Q	7Q

OE does not affect internal operations of the latches. Old data can be retained or new data can be entered while the outputs are in the high-impedance state.

The SN54AC563 is characterized for operation over the full military temperature range of ±55°C to 125°C. The SN74AC563 is characterized for operation from ±40°C to 85°C.

FUNCTION TABLE (each latch)

		INPUTS		OUTPUT
		LE	D		Q
	OE
	L	H	H		L
	L	H	L		H
	L	L	X
					Q	0
	H	X	X		Z

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

EPIC is a trademark of Texas Instruments Incorporated.

UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.

Copyright 1996, Texas Instruments Incorporated

POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

1

SN54AC563, SN74AC563

OCTAL D-TYPE TRANSPARENT LATCHES

WITH 3-STATE OUTPUTS

SCAS552A ± NOVEMBER 1995 ± REVISED MAY 1996

logic symbol²

logic diagram (positive logic)

1	EN				1
OE				OE
11	C1
LE					11
				LE
2			19
	1D	1
1D			1Q
3			18			C1
2D			2Q				19	1Q
4			17	1D	2	1D
3D			3Q
5			16
4D			4Q
6			15
5D			5Q
7			14
6D			6Q			To Seven Other Channels
8			13
7D			7Q
9			12
8D			8Q

²This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)³

Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . ±0.5 V to 7	V
Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	±0.5 V to VCC + 0.5	V
Output voltage range, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	±0.5 V to VCC + 0.5	V
Input clamp current, IIK (VI < 0 or VI > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . ±20 mA
Output clamp current, IOK (VO < 0 or VO > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . ±20 mA
Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . . . ±50 mA
Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . . . . . . . ±200 mA
Maximum power dissipation at TA = 55°C (in still air) (see Note 2): DB package . . . . .	. . . . . . . . . . . . 0.6 W
DW package . . . . .	. . . . . . . . . . . . 1.6 W
N package . . . . . . .	. . . . . . . . . . . . 1.3 W
PW package . . . . .	. . . . . . . . . . . . 0.7 W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . . ±65°C to 150°C

³Stresses beyond those listed under ªabsolute maximum ratingsº may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under ªrecommended operating conditionsº is not

implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.

2.The maximum package power dissipation is calculated using a junction temperature of 150°C and a board trace length of 750 mils, except for the N package, which has a trace length of zero.

2	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265