July 1997
Revised March 1999
74VHCT00A
Quad 2-Input NAND Gate
General Description
The VHCT00A is an advanced high-speed CMOS 2-Input NAND Gate fabricated with silicon gate CMOS technology. It achieves the high-speed operation similar to equivalent Bipolar Schottky TTL while maintaining the CMOS low power dissipation. The internal circuit is composed of 3 stages, including buffer output, which provide high noise immunity and stable output.
Protection circuits ensure that 0V to 7V can be applied to the input pins without regard to the supply voltage and to the output pins with VCC = 0V. These circuits prevent device destruction due to mismatched supply and input/ output voltages. This device can be used to interface 3V to
5V systems and two supply systems such as battery backup.
Features
■High speed: tPD = 5.0 ns (typ) at TA = 25°C
■High noise immunity: VIH = 2.0V, VIL = 0.8V
■Power down protection is provided on all inputs and outputs
■Low noise: VOLP = 0.8V (max)
■Low power dissipation:
ICC = 2 μA (max) at TA = 25°C
■Pin and function compatible with 74HCT00
Ordering Code:
Order Number |
Package Number |
Package Description |
|
|
|
74VHCT00AM |
M14A |
14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-120, 0.150 Narrow |
|
|
|
74VHCT00ASJ |
M14D |
14-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide |
|
|
|
74VHCT00AMTC |
MTC14 |
14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide |
|
|
|
74VHCT00AN |
N14A |
14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300 Wide |
|
|
|
Surface mount packages are also available on Tape and Reel. Specify by appending the suffix letter “X” to the ordering code.
Logic Symbol |
Connection Diagram |
Pin Descriptions |
Truth Table |
|
|
Pin Names |
Description |
|
|
|
|
|
An, Bn |
Inputs |
|
|
|
Outputs |
|
|
O |
n |
A |
B |
O |
|
|
|
L |
L |
H |
|
|
|
L |
H |
H |
|
|
|
H |
L |
H |
|
|
|
H |
H |
L |
|
|
|
Gate NAND Input-2 Quad 74VHCT00A
© 1999 Fairchild Semiconductor Corporation |
DS500023.prf |
www.fairchildsemi.com |
74VHCT00A |
|
Absolute Maximum Ratings(Note 1) |
Recommended Operating |
|
|
|
|||||||||||||||
|
|
|
|
|
|||||||||||||||||
|
|
Supply Voltage (VCC) |
|
|
−0.5V to +7.0V |
Conditions (Note 5) |
|
|
|
|
|
||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
DC Input Voltage (VIN) |
|
|
−0.5V to +7.0V |
Supply Voltage (VCC) |
|
|
|
|
4.5V to 5.5V |
||||||||||
|
|
DC Output Voltage (VOUT) |
−0.5V to VCC + 0.5V |
Input Voltage (VIN) |
|
|
|
|
0V to +5.5V |
||||||||||||
|
|
(Note 2) |
Output Voltage (VOUT) |
|
|
|
|
|
|
|
|||||||||||
|
|
(Note 3) |
|
|
−0.5V to 7.0V |
(Note 2) |
|
|
|
|
|
|
|
0V to VCC |
|||||||
|
|
Input Diode Current (IIK) |
|
|
|
−20 mA |
(Note 3) |
|
|
|
|
|
|
|
0V to 5.5V |
||||||
|
|
Output Diode Current (IOK) |
|
|
|
±20 mA |
Operating Temperature (TOPR) |
|
−40°C to +85°C |
||||||||||||
|
|
(Note 4) |
|
|
|
Input Rise and Fall Time (tr, tf) |
|
|
|
|
|
||||||||||
|
|
DC Output Current (IOUT) |
|
|
|
±25 mA |
VCC = 5.0V ± 0.5V |
|
|
|
0 ns/V 20 ns/V |
||||||||||
|
|
DC VCC/GND Current (ICC) |
|
|
|
±50 mA |
Note 1: Absolute Maximum Ratings are values beyond which the device |
||||||||||||||
|
|
Storage Temperature (TSTG) |
|
−65°C to +150°C |
may be damaged or have its useful life impaired. The databook specifica- |
||||||||||||||||
|
|
|
tions should be met, without exception, to ensure that the system design is |
||||||||||||||||||
|
|
Lead Temperature (TL) |
|
|
|
|
|
reliable over its power supply, temperature, and output/input loading vari- |
|||||||||||||
|
|
|
|
|
260°C |
ables. Fairchild does not recommend operation outside databook specifica- |
|||||||||||||||
|
|
(Soldering, 10 seconds) |
|
|
|
||||||||||||||||
|
|
|
|
|
tions. |
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
Note 2: HIGH or LOW state. IOUT absolute maximum rating must be |
||||||||||
|
|
|
|
|
|
|
|
|
|
|
observed. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Note 3: VCC = 0V. |
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
Note 4: VOUT < GND, VOUT > VCC (Outputs Active) |
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
Note 5: Unused inputs must be held HIGH or LOW. They may not float. |
||||||||||
|
|
DC Electrical Characteristics |
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
V |
|
|
TA = 25°C |
|
|
TA = −40°C to +85°C |
|
|
|
|
|
|
|||
|
|
Symbol |
|
Parameter |
|
CC |
|
|
|
|
|
|
|
|
|
|
Units |
Conditions |
|||
|
|
|
|
(V) |
|
Min |
Typ |
Max |
|
Min |
Max |
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
VIH |
|
HIGH Level Input Voltage |
|
4.5 |
|
2.0 |
|
|
|
|
2.0 |
|
|
|
V |
|
|
|
|
|
|
|
|
|
|
|
5.5 |
|
2.0 |
|
|
|
|
2.0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
VIL |
|
LOW Level Input Voltage |
|
4.5 |
|
|
|
|
0.8 |
|
|
|
0.8 |
|
V |
|
|
|
|
|
|
|
|
|
|
|
5.5 |
|
|
|
|
0.8 |
|
|
|
0.8 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
VOH |
|
HIGH Level Output Voltage |
|
4.5 |
|
4.40 |
4.50 |
|
|
|
4.40 |
|
|
|
V |
VIN = VIH |
|
IOH = −50 μA |
||
|
|
|
|
|
|
4.5 |
|
3.94 |
|
|
|
|
3.80 |
|
|
|
V |
or VIL |
|
IOH = −8 mA |
|
|
VOL |
|
LOW Level Output Voltage |
|
4.5 |
|
|
0.0 |
|
0.1 |
|
|
|
0.1 |
|
V |
VIN = VIH |
|
IOL = 50 μA |
||
|
|
|
|
|
|
4.5 |
|
|
|
|
0.36 |
|
|
|
0.44 |
|
V |
or VIL |
|
IOL = 8 mA |
|
|
IIN |
|
Input Leakage Current |
|
0 − 5.5 |
|
|
|
|
±0.1 |
|
|
|
±1.0 |
|
μA |
VIN = 5.5V |
or GND |
|||
|
ICC |
|
Quiescent Supply Current |
|
5.5 |
|
|
|
|
2.0 |
|
|
|
20.0 |
|
μA |
VIN = VCC or GND |
||||
|
ICCT |
|
Maximum ICC/ Input |
|
5.5 |
|
|
|
|
1.35 |
|
|
|
1.50 |
|
mA |
VIN = 3.4V |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Other Inputs = VCC or GND |
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
IOFF |
|
Output Leakage Current |
|
0.0 |
|
|
|
|
0.5 |
|
|
|
5.0 |
|
μA |
VOUT = 5.5V |
||||
|
|
|
|
(Power Down State) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Noise Characteristics |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
V |
|
TA = 25°C |
|
|
|
|
|
|
|
|
||
|
|
Symbol |
|
Parameter |
|
|
|
CC |
|
|
|
|
|
Units |
|
Conditions |
|||||
|
|
|
|
|
|
(V) |
|
Typ |
Limit |
|
|
||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
VOLP |
|
Quiet Output Maximum Dynamic VOL |
|
|
5.0 |
|
0.4 |
|
0.8 |
|
V |
CL = 50 pF |
|
|
|
||||
|
|
(Note 6) |
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
VOLV |
|
Quiet Output Minimum Dynamic VOL |
|
|
5.0 |
|
−0.4 |
−0.8 |
|
V |
CL = 50 pF |
|
|
|
|||||
|
|
(Note 6) |
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
VIHD |
|
Minimum HIGH Level Dynamic Input Voltage |
5.0 |
|
|
|
2.0 |
|
V |
CL = 50 pF |
|
|
|
||||||
|
|
(Note 6) |
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
VILD |
|
Maximum LOW Level Dynamic Input Voltage |
5.0 |
|
|
|
0.8 |
|
V |
CL = 50 pF |
|
|
|
||||||
|
|
(Note 6) |
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
Note 6: Parameter guaranteed by design. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
www.fairchildsemi.com |
2 |