Texas Instruments UC3825QTR, UC3825QRTR, UC3825Q, UC3825N, UC3825J Datasheet

UC1825

UC2825

UC3825

High Speed PWM Controller

FEATURES

∙Compatible with Voltage or Current Mode Topologies

∙Practical Operation Switching Frequencies to 1MHz

∙50ns Propagation Delay to Output

∙High Current Dual Totem Pole Outputs (1.5A Peak)

∙Wide Bandwidth Error Amplifier

∙Fully Latched Logic with Double Pulse Suppression

∙Pulse-by-Pulse Current Limiting

∙Soft Start / Max. Duty Cycle Control

∙Under-Voltage Lockout with Hysteresis

∙Low Start Up Current (1.1mA)

∙Trimmed Bandgap Reference (5.1V ±1%)

DESCRIPTION

The UC1825 family of PWM control ICs is optimized for high frequency switched mode power supply applications. Particular care was given to minimizing propagation delays through the comparators and logic circuitry while maximizing bandwidth and slew rate of the error amplifier. This controller is designed for use in either currentmode or voltage mode systems with the capability for input voltage feed-forward.

Protection circuitry includes a current limit comparator with a 1V threshold, a TTL compatible shutdown port, and a soft start pin which will double as a maximum duty cycle clamp. The logic is fully latched to provide jitter free operation and prohibit multiple pulses at an output. An under-voltage lockout section with 800mV of hysteresis assures low start up current. During under-voltage lockout, the outputs are high impedance.

These devices feature totem pole outputs designed to source and sink high peak currents from capacitive loads, such as the gate of a power MOSFET. The on state is designed as a high level.

BLOCK DIAGRAM

UDG-92030-2

3/97

ABSOLUTE MAXIMUM RATINGS (Note 1)

Supply Voltage (Pins 13, 15) . . . . . . . . . . . . . . . . . . . . . . . . 30V Output Current, Source or Sink (Pins 11, 14)

DC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5A Pulse (0.5μs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0A Analog Inputs

(Pins 1, 2, 7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 7V (Pin 8, 9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6V Clock Output Current (Pin 4) . . . . . . . . . . . . . . . . . . . . . . . -5mA Error Amplifier Output Current (Pin 3) . . . . . . . . . . . . . . . . 5mA Soft Start Sink Current (Pin 8) . . . . . . . . . . . . . . . . . . . . . 20mA Oscillator Charging Current (Pin 5) . . . . . . . . . . . . . . . . . . -5mA Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1W Storage Temperature Range . . . . . . . . . . . . . . -65°C to +150°C Lead Temperature (Soldering, 10 seconds) . . . . . . . . . . 300°C

Note 1: All voltages are with respect to GND (Pin 10); all currents are positive into, negative out of part; pin numbers refer to DIL-16 package.

Note 3: Consult Unitrode Integrated Circuit Databook for thermal limitations and considerations of package.

SOIC-16 (Top View)

DW Package

UC1825

UC2825

UC3825

CONNECTION DIAGRAMS

DIL-16 (Top View)

J Or N Package

	PLCC-20 & LCC-20	PACKAGE PIN FUNCTION
		FUNCTION	PIN
	(Top View)	N/C	1
	Q & L Packages	INV	2
		NI	3
		E/A Out	4
		Clock	5
		N/C	6
		RT	7
		CT	8
		Ramp	9
		Soft Start	10
		N/C	11
		ILIM/SD	12
		Gnd	13
		Out A	14
		Pwr Gnd	15
		N/C	16
		VC	17
		Out B	18
		VCC	19
		VREF 5.1V	20

ELECTRICAL CHARACTERISTICS: Unless otherwise stated,these specifications apply for , RT = 3.65k, CT = 1nF, VCC
	= 15V, -55°C<TA<125°C for the UC1825, –40°C<TA<85°C for the UC2825, and
	0°C<TA<70°C for the UC3825, TA=TJ.
			UC1825			UC3825
PARAMETERS	TEST CONDITIONS		UC2825
		MIN	TYP	MAX	MIN	TYP	MAX	UNITS
Reference Section
Output Voltage	TJ = 25°C, IO = 1mA	5.05	5.10	5.15	5.00	5.10	5.20	V
Line Regulation	10V < VCC < 30V		2	20		2	20	mV
Load Regulation	1mA < IO < 10mA		5	20		5	20	mV
Temperature Stability*	TMIN < TA < TMAX		0.2	0.4		0.2	0.4	mV/°C
Total Output Variation*	Line, Load, Temperature	5.00		5.20	4.95		5.25	V
Output Noise Voltage*	10Hz < f < 10kHz		50			50		μV
Long Term Stability*	TJ = 125°C, 1000hrs.		5	25		5	25	mV
Short Circuit Current	VREF = 0V	-15	-50	-100	-15	-50	-100	mA
Oscillator Section
Initial Accuracy*	TJ = 25°C	360	400	440	360	400	440	kHz
Voltage Stability*	10V < VCC < 30V		0.2	2		0.2	2	%
Temperature Stability*	TMIN < TA < TMAX		5			5		%
Total Variation*	Line, Temperature	340		460	340		460	kHz

2

ELECTRICAL CHARACTERISTICS (cont.)

UC1825

UC2825

UC3825

Unless otherwise stated,these specifications apply for , RT = 3.65k, CT

= 1nF, VCC = 15V, -55°C<TA<125°C for the UC1825, –40°C<TA<85°C for the UC2825, and 0°C<TA<70°C for the UC3825, TA=TJ.

			UC1825			UC3825
PARAMETERS	TEST CONDITIONS		UC2825
		MIN	TYP	MAX	MIN	TYP	MAX	UNITS
Oscillator Section (cont.)
Clock Out High		3.9	4.5		3.9	4.5		V
Clock Out Low			2.3	2.9		2.3	2.9	V
Ramp Peak*		2.6	2.8	3.0	2.6	2.8	3.0	V
Ramp Valley*		0.7	1.0	1.25	0.7	1.0	1.25	V
Ramp Valley to Peak*		1.6	1.8	2.0	1.6	1.8	2.0	V
Error Amplifier Section
Input Offset Voltage				10			15	mV
Input Bias Current			0.6	3		0.6	3	μA
Input Offset Current			0.1	1		0.1	1	μA
Open Loop Gain	1V < VO < 4V	60	95		60	95		dB
CMRR	1.5V < VCM < 5.5V	75	95		75	95		dB
PSRR	10V < VCC < 30V	85	110		85	110		dB
Output Sink Current	VPIN 3 = 1V	1	2.5		1	2.5		mA
Output Source Current	VPIN 3 = 4V	-0.5	-1.3		-0.5	-1.3		mA
Output High Voltage	IPIN 3 = -0.5mA	4.0	4.7	5.0	4.0	4.7	5.0	V
Output Low Voltage	IPIN 3 = 1mA	0	0 .5	1.0	0	0.5	1.0	V
Unity Gain Bandwidth*		3	5.5		3	5.5		MHz
Slew Rate*		6	12		6	12		V/μs
PWM Comparator Section
Pin 7 Bias Current	VPIN 7 = 0V		-1	-5		-1	-5	μA
Duty Cycle Range		0		80	0		85	%
Pin 3 Zero DC Threshold	VPIN 7 = 0V	1.1	1.25		1.1	1.25		V
Delay to Output*			50	80		50	80	ns
Soft-Start Section
Charge Current	VPIN 8 = 0.5V	3	9	20	3	9	20	μA
Discharge Current	VPIN 8 = 1V	1			1			mA
Current Limit / Shutdown Section
Pin 9 Bias Current	0 < VPIN 9 < 4V			15			10	μA
Current Limit Threshold		0.9	1.0	1.1	0.9	1.0	1.1	V
Shutdown Threshold		1.25	1.40	1.55	1.25	1.40	1.55	V
Delay to Output			50	80		50	80	ns
Output Section
Output Low Level	IOUT = 20mA		0.25	0.40		0.25	0.40	V
	IOUT = 200mA		1.2	2.2		1.2	2.2	V
Output High Level	IOUT = -20mA	13.0	13.5		13.0	13.5		V
	IOUT = -200mA	12.0	13.0		12.0	13.0		V
Collector Leakage	VC = 30V		100	500		10	500	μA
Rise/Fall Time*	CL = 1nF		30	60		30	60	ns
Under-Voltage Lockout Section
Start Threshold		8.8	9.2	9.6	8.8	9.2	9.6	V
UVLO Hysteresis		0.4	0.8	1.2	0.4	0.8	1.2	V
Supply Current Section
Start Up Current	VCC = 8V		1.1	2.5		1.1	2.5	mA
ICC	VPIN 1, VPIN 7, VPIN 9 = 0V; VPIN 2 = 1V		22	33		22	33	mA

* This parameter not 100% tested in production but guaranteed by design.

3