September 1983
Revised February 1999
MM74HC04
Hex Inverter
General Description
The MM74HC04 inverters utilize advanced silicon-gate CMOS technology to achieve operating speeds similar to LS-TTL gates with the low power consumption of standard CMOS integrated circuits.
The MM74HC04 is a triple buffered inverter. It has high noise immunity and the ability to drive 10 LS-TTL loads. The 74HC logic family is functionally as well as pin-out compatible with the standard 74LS logic family. All inputs
are protected from damage due to static discharge by internal diode clamps to VCC and ground.
Features
■Typical propagation delay: 8 ns
■Fan out of 10 LS-TTL loads
■Quiescent power consumption: 10 μW maximum at room temperature
■Low input current: 1 μA maximum
Ordering Code:
Order Number |
Package Number |
Package Description |
|
|
|
MM74HC04M |
M14A |
14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-120, 0.150” Narrow |
|
|
|
MM74HC04SJ |
M14D |
14-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.5mm Wide |
|
|
|
MM74HC04MTC |
MTC14 |
14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide |
|
|
|
MM74HC04N |
N14A |
14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300” Wide |
|
|
|
Devices also available in Tape and Reel. Specify by appending the suffix letter “X” to the ordering code.
Connection Diagram |
Logic Diagram |
Pin Assignments for DIP, SOIC, SOP and TSSOP |
1 of 6 Inverters |
Top View
Inverter Hex MM74HC04
© 1999 Fairchild Semiconductor Corporation |
DS005069.prf |
www.fairchildsemi.com |
MM74HC04
Absolute Maximum Ratings(Note 1)
(Note 2) |
|
Supply Voltage (VCC) |
−0.5 to +7.0V |
DC Input Voltage (VIN) |
−1.5 to VCC +1.5V |
DC Output Voltage (VOUT) |
−0.5 to VCC +0.5V |
Clamp Diode Current (IIK, IOK) |
±20 mA |
DC Output Current, per pin (IOUT) |
±25 mA |
DC VCC or GND Current, per pin (ICC) |
±50 mA |
Storage Temperature Range (TSTG) |
−65°C to +150°C |
Power Dissipation (PD) |
|
(Note 3) |
600 mW |
S.O. Package only |
500 mW |
Lead Temperature (TL) |
260°C |
(Soldering 10 seconds) |
Recommended Operating
Conditions
|
Min |
Max |
Units |
Supply Voltage (VCC) |
2 |
6 |
V |
DC Input or Output Voltage |
0 |
VCC |
V |
(VIN, VOUT) |
−40 |
+85 |
°C |
Operating Temperature Range (TA) |
|||
Input Rise or Fall Times |
|
|
|
(tr, tf) VCC = 2.0V |
|
1000 |
ns |
VCC = 4.5V |
|
500 |
ns |
VCC = 6.0V |
|
400 |
ns |
Note 1: Absolute Maximum Ratings are those values beyond which damage to the device may occur.
Note 2: Unless otherwise specified all voltages are referenced to ground.
Note 3: Power Dissipation temperature derating — plastic “N” package: − 12 mW/°C from 65°C to 85°C.
DC Electrical Characteristics |
(Note 4) |
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
Symbol |
Parameter |
Conditions |
VCC |
TA = 25°C |
TA = −40 to 85°C |
TA = −55 to 125°C |
Units |
|
Typ |
|
Guaranteed Limits |
||||||
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
VIH |
Minimum HIGH Level |
|
2.0V |
|
1.5 |
1.5 |
1.5 |
V |
|
Input Voltage |
|
4.5V |
|
3.15 |
3.15 |
3.15 |
V |
|
|
|
6.0V |
|
4.2 |
4.2 |
4.2 |
V |
|
|
|
|
|
|
|
|
|
VIL |
Maximum LOW Level |
|
2.0V |
|
0.5 |
0.5 |
0.5 |
V |
|
Input Voltage |
|
4.5V |
|
1.35 |
1.35 |
1.35 |
V |
|
|
|
6.0V |
|
1.8 |
1.8 |
1.8 |
V |
|
|
|
|
|
|
|
|
|
VOH |
Minimum HIGH Level |
VIN = VIL |
|
|
|
|
|
|
|
Output Voltage |
|IOUT| ≤ 20 μA |
2.0V |
2.0 |
1.9 |
1.9 |
1.9 |
V |
|
|
|
4.5V |
4.5 |
4.4 |
4.4 |
4.4 |
V |
|
|
|
6.0V |
6.0 |
5.9 |
5.9 |
5.9 |
V |
|
|
|
|
|
|
|
|
|
|
|
VIN = VIL |
|
|
|
|
|
|
|
|
|IOUT| ≤ 4.0 mA |
4.5V |
4.2 |
3.98 |
3.84 |
3.7 |
V |
|
|
|IOUT| ≤ 5.2 mA |
6.0V |
5.7 |
5.48 |
5.34 |
5.2 |
V |
VOL |
Maximum LOW Level |
VIN = VIH |
|
|
|
|
|
|
|
Output Voltage |
|IOUT| ≤ 20 μA |
2.0V |
0 |
0.1 |
0.1 |
0.1 |
V |
|
|
|
4.5V |
0 |
0.1 |
0.1 |
0.1 |
V |
|
|
|
6.0V |
0 |
0.1 |
0.1 |
0.1 |
V |
|
|
|
|
|
|
|
|
|
|
|
VIN = VIH |
|
|
|
|
|
|
|
|
|IOUT| ≤ 4.0 mA |
4.5V |
0.2 |
0.26 |
0.33 |
0.4 |
V |
|
|
|IOUT| ≤ 5.2 mA |
6.0V |
0.2 |
0.26 |
0.33 |
0.4 |
V |
IIN |
Maximum Input |
VIN = VCC or GND |
6.0V |
|
±0.1 |
±1.0 |
±1.0 |
μA |
|
Current |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ICC |
Maximum Quiescent |
VIN = VCC or GND |
6.0V |
|
2.0 |
20 |
40 |
μA |
|
Supply Current |
IOUT = 0 μA |
|
|
|
|
|
|
Note 4: For a power supply of 5V ±10% the worst case output voltages (VOH, and VOL) occur for HC at 4.5V. Thus the 4.5V values should be used when designing with this supply. Worst case VIH and VIL occur at VCC=5.5V and 4.5V respectively. (The VIH value at 5.5V is 3.85V.) The worst case leakage current (IIN, ICC, and IOZ) occur for CMOS at the higher voltage and so the 6.0V values should be used.
www.fairchildsemi.com |
2 |