ST3222E
±15KV ESD-PROTECTED, 3 TO 5.5V, LOW POWER, UP TO 250KBPS, RS-232 DRIVERS AND RECEIVERS
■ESD PROTECTIO FOR RS-232 I/O PINS ±15KV HUMAN BODY MODEL
±8KV IEC 1000-4-2 CONTACT DISCHARGE
■300μA SUPPLY CURRENT
■250Kbps MINIMUM GUARENTEED DATA RATE
■6V/μs MINIMUM GUARANTEED SLEW RATE
■MEET EIA/TIA-232 SPECIFICATIONS DOWN TO 3V
■AVAILABLE IN SO-18, SSOP20 AND TSSOP20
DESCRIPTION
The ST3222E is a 3V powered EIA/TIA-232 and V.28/V.24 communications interface with low power requirements, high data-rate capabilities and enhanced electrostatic discharge (ESD) protection to ±8kV using IEC1000-4-2 Contact Discharge and ±15kV using the Human Body Model. ST3222E has a proprietary low dropout transmitter output stage providing true RS-232 performance from 3 to 5V supplies with a dual charge pump. The charge pump requires only four small 0.1mF external capacitors for operation form 3V supply.
The device has two receivers and two drivers. The ST3222E features a 1μA shutdown mode that reduces power consumption and extends battery life in portable systems. Its receivers can remain active in shutdown mode, allowing external
ORDERING CODES
SOP |
SSOP |
TSSOP
devices such as modems to be monitored using only 1μA supply current.
The device is guaranteed to run at data rates of 250Kbps while maintaining RS-232 output levels. Typical applications are Notebook, Subnotebook and Palmtop Computers, Battery Powered Equipment, Hand-Held Equipment, Peripherals and Printers.
Type |
Temperature |
Package |
Comments |
|
Range |
||||
|
|
|
||
|
|
|
|
|
ST3222ECD |
0 to 70 °C |
SO-18 (Tube) |
50parts per tube / 20tube per box |
|
|
|
|
|
|
ST3222EBD |
-40 to 85 °C |
SO-18 (Tube) |
50parts per tube / 20tube per box |
|
|
|
|
|
|
ST3222ECDR |
0 to 70 °C |
SO-18 (Tape & Reel) |
1000 parts per reel |
|
|
|
|
|
|
ST3222EBDR |
-40 to 85 °C |
SO-18 (Tape & Reel) |
1000 parts per reel |
|
|
|
|
|
|
ST3222ECPR |
0 to 70 °C |
SSOP20 (Tape & Reel) |
1350 parts per reel |
|
|
|
|
|
|
ST3222EBPR |
-40 to 85 °C |
SSOP20 (Tape & Reel) |
1350 parts per reel |
|
|
|
|
|
|
ST3222ECTR |
0 to 70 °C |
TSSOP20 (Tape & Reel) |
2500 parts per reel |
|
|
|
|
|
|
ST3222EBTR |
-40 to 85 °C |
TSSOP20 (Tape & Reel) |
2500 parts per reel |
|
|
|
|
|
|
March 2003 |
|
|
1/10 |
|
|
|
|
|
ST3222E
PIN CONFIGURATION
|
|
|
|
SO-18 |
|
|
|
SSOP20/TSSOP20 |
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PIN DESCRIPTION
PlN N° |
PlN N° |
SYMBOL |
NAME AND FUNCTION |
|||||
(SO-18) |
(SSOP20 TSSP20) |
|||||||
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
||
1 |
1 |
|
|
EN |
|
|
Receiver Enable Control. Drive low for normal |
|
|
|
|
|
|
|
|
operation. Drive high to force the receivers outputs |
|
|
|
|
|
|
|
|
(R_OUT) into a high-impedance state. |
|
|
|
|
|
|
|
|
|
|
2 |
2 |
|
C1+ |
Positive Terminal for the first Charge Pump |
||||
|
Capacitor |
|||||||
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|||
3 |
3 |
|
|
V+ |
5.5V Generated By The Charge Pump. |
|||
4 |
4 |
|
C1- |
Negative Terminal for the first Charge Pump |
||||
|
Capacitor |
|||||||
|
|
|
|
|
|
|
||
5 |
5 |
|
C2+ |
Positive Terminal for the second Charge Pump |
||||
|
Capacitor |
|||||||
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
6 |
6 |
|
C2- |
Negative Terminal for the second Charge Pump |
||||
|
Capacitor |
|||||||
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|||
7 |
7 |
|
|
V- |
-5.5V Generated By The Charge Pump. |
|||
|
|
|
|
|||||
8 |
8 |
T2OUT |
Second Transmitter Output Voltage |
|||||
9 |
9 |
|
R2IN |
Second Receiver Input Voltage |
||||
10 |
10 |
R2OUT |
Second Receiver Output Voltage |
|||||
|
11 |
|
NC |
Not Connected |
||||
|
|
|
|
|
||||
11 |
12 |
|
T2IN |
Second Transmitter Input Voltage |
||||
12 |
13 |
|
T1IN |
First Transmitter Input Voltage |
||||
|
14 |
|
NC |
Not Connected |
||||
|
|
|
|
|||||
13 |
15 |
R1OUT |
First Receiver Output Voltage |
|||||
14 |
16 |
|
R1IN |
First Receiver Input Voltage |
||||
15 |
17 |
T1OUT |
First Transmitter Output Voltage |
|||||
16 |
18 |
|
GND |
Ground |
||||
17 |
19 |
|
VCC |
Supply Voltage |
||||
18 |
20 |
|
SHDN |
Active Low Shutdown Control Input. Drive Low To |
||||
|
|
|
|
|
|
|
Shut-down Transmittes And Charge Pump |
|
|
|
|
|
|
|
|
|
2/10
|
|
|
|
|
ST3222E |
ABSOLUTE MAXIMUM RATINGS |
|
|
|||
|
|
|
|
||
Symbol |
Parameter |
Value |
Unit |
||
|
|
|
|
|
|
|
VCC |
Supply Voltage |
-0.3 to 6 |
V |
|
|
V+ |
Doubled Voltage Terminal |
(VCC - 0.3) to 7 |
V |
|
|
V- |
Inverted Voltage Terminal |
0.3 to -7 |
V |
|
|
|
|
|
||
V+ +|V-| |
|
13 |
V |
||
|
|
|
|
|
|
|
TIN |
Transmitter Input Voltage Range |
-0.3 to 6 |
V |
|
|
SHDN |
|
Transmitter Input Voltage Range |
-0.3 to 6 |
V |
|
|
|
|
|
|
|
RIN |
Receiver Input Voltage Range |
± 25 |
V |
|
|
TOUT |
Transmitter Output Voltage Range |
± 13.2 |
V |
|
|
ROUT |
Receiver Output Voltage Range |
-0.3 to (VCC + 0.3) |
V |
|
tSHORT |
Transmitter Output Short to GND Time |
Continuous |
|
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. V+ and V- can have a maximum magnitude of +7V, but their absolute addition can not exceed 13 V.
SHUTDOWN AND ENABLE CONTROL TRUTH TABLE
|
|
|
|
|
|
|
|
SHDN |
EN |
T-OUT |
R-OUT |
||||
|
|
|
|
|
|
|
|
0 |
|
0 |
|
High Z |
Active |
||
|
|
|
|
|
|
|
|
0 |
|
1 |
|
High Z |
High Z |
||
|
|
|
|
|
|
|
|
1 |
|
0 |
|
Active |
Active |
||
|
|
|
|
|
|
|
|
1 |
|
1 |
|
Active |
High Z |
ESD PERFORMANCE: TRANSMITTER OUTPUTS, RECEIVER INPUTS
Symbol |
Parameter |
Test Conditions |
Min. |
Typ. |
Max. |
Unit |
|
|
|
|
|
|
|
ESD |
ESD Protection Voltage |
Human Body Model |
±15 |
|
|
kV |
|
|
|
|
|
|
|
ESD |
ESD Protection Voltage |
IEC-1000-4-2 |
±8 |
|
|
kV |
|
|
|
|
|
|
|
ELECTRICAL CHARACTERISTICS
(C1 - C4 = 0.1μF, VCC = 3V to 5.5V, TA = -40 to 85°C, unless otherwise specified. Typical values are referred to TA = 25°C)
Symbol |
Parameter |
|
Test Conditions |
Min. |
Typ. |
Max. |
Unit |
||
|
|
|
|
|
|
|
|
|
|
ISUPPLY |
VCC Power Supply Current |
No Load |
|
SHDN=VCCTA = 25°C |
|
0.3 |
1 |
mA |
|
ISHDN |
SHUTDOWN Supply |
No Load |
|
SHDN=VCCTA = 25°C |
|
1 |
10 |
μA |
|
|
Current |
|
|
|
|
|
|
|
|
LOGIC INPUT ELECTRICAL CHARACTERISTICS
(C1 - C4 = 0.1μF, VCC = 3V to 5.5V, TA = -40 to 85°C, unless otherwise specified. Typical values are referred to TA = 25°C)
Symbol |
Parameter |
|
|
|
Test Conditions |
Min. |
Typ. |
Max. |
Unit |
|
|
|
|
|
|
|
|
|
|
||
VIL |
Input Logic Threshold Low |
T-IN, EN, SHDN (Note 1) |
|
|
0.8 |
V |
||||
VIH |
Input Logic Threshold High |
VCC = 3.3V |
2 |
|
|
V |
||||
|
|
VCC = 5V |
2.4 |
|
|
|
||||
VHYS |
Transmitter Input |
|
|
|
|
|
|
0.25 |
|
V |
|
Histeresys |
|
|
|
|
|
|
|
|
|
IIL |
Input Leakage Current |
T-IN, EN, SHDN |
|
± 0.01 |
± 1 |
μA |
Note 1: Transmitter input hysteresis is typically 250mV
3/10