ST62T15C/T25C/E25C
8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, OSCILLATOR SAFEGUARD, SAFE RESET AND 28 PINS
■3.0 to 6.0V Supply Operating Range
■8 MHz Maximum Clock Frequency
■-40 to +125°C Operating Temperature Range
■Run, Wait and Stop Modes
■5 Interrupt Vectors
■Look-up Table capability in Program Memory
■Data Storage in Program Memory: User selectable size
■Data RAM: 64bytes
■User Programmable Options
■20 I/O pins, fully programmable as:
±Input with pull-up resistor
±Input without pull-up resistor
±Input with interrupt generation
±Open-drain or push-pull output
±Analog Input
■4 I/O lines can sink up to 20mA to drive LEDs or TRIACs directly
■8-bit Timer/Counter with 7-bit programmable prescaler
■Digital Watchdog
■Oscillator Safe Guard
■Low Voltage Detector for Safe Reset
■8-bit A/D Converter with 16 analog inputs
■On-chip Clock oscillator can be driven by Quartz Crystal Ceramic resonator or RC network
■Power-on Reset
■One external Non-Maskable Interrupt
■ST626x-EMU2 Emulation and Development System (connects to an MS-DOS PC via a parallel port).
DEVICE SUMMARY
DEVICE |
OTP |
EPROM |
I/O Pins |
|
(Bytes) |
(Bytes) |
|||
|
|
|||
ST62T15C |
1836 |
- |
20 |
|
ST62T25C |
3884 |
- |
20 |
|
ST62E25C |
|
3884 |
20 |
PDIP28
PS028
SS0P28
CDIP28W
(See end of Datasheet for Ordering Information)
Rev. 2.8
August 1999 |
1/70 |
Table of Contents
Document
Page
ST62T15C/T25C/E25C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1 GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. 4 |
||
1.1 |
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
4 |
|
1.2 |
PIN DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
5 |
|
1.3 |
MEMORY MAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
6 |
|
|
1.3.1 |
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
6 |
|
1.3.2 |
Program Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
7 |
|
1.3.3 |
Data Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
8 |
|
1.3.4 |
Stack Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
8 |
|
1.3.5 |
Data Window Register (DWR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
9 |
1.4 |
PROGRAMMING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
10 |
|
|
1.4.1 |
Option Bytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
10 |
|
1.4.2 |
Program Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
11 |
|
1.4.3 |
EPROM Erasing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
11 |
2 CENTRAL PROCESSING UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
12 |
||
2.1 |
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
12 |
|
2.2 |
CPU REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
12 |
|
3 CLOCKS, RESET, INTERRUPTS AND POWER SAVING MODES . . . . . . . . . . . . . . . . . . . . . |
14 |
||
3.1 |
CLOCK SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
14 |
|
|
3.1.1 |
Main Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
14 |
|
3.1.2 Low Frequency Auxiliary Oscillator (LFAO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
15 |
|
|
3.1.3 |
Oscillator Safe Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
15 |
3.2 |
RESETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
18 |
|
|
3.2.1 |
RESET Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
18 |
|
3.2.2 |
Power-on Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
18 |
|
3.2.3 |
Watchdog Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
19 |
|
3.2.4 |
LVD Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
19 |
|
3.2.5 |
Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
19 |
|
3.2.6 |
MCU Initialization Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
20 |
3.3 |
DIGITAL WATCHDOG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
22 |
|
|
3.3.1 |
Digital Watchdog Register (DWDR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
24 |
|
3.3.2 |
Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
24 |
3.4 |
INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
26 |
|
|
3.4.1 |
Interrupt request . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
26 |
|
3.4.2 |
Interrupt Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
27 |
|
3.4.3 |
Interrupt Option Register (IOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
28 |
|
3.4.4 |
Interrupt sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
28 |
3.5 |
POWER SAVING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
30 |
3.5.1 WAIT Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 3.5.2 STOP Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 3.5.3 Exit from WAIT and STOP Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4 ON-CHIP PERIPHERALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
70
4.1 I/O PORTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 4.1.1 Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2/70
Table of Contents
Document
Page
4.1.2 Safe I/O State Switching Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.1.3 I/O Port Option Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.1.4 I/O Port Data Direction Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.1.5 I/O Port Data Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.2 TIMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.2.1 Timer Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 4.2.2 Timer Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 4.2.3 Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 4.2.4 Timer Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 4.3 A/D CONVERTER (ADC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.3.1 Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
5 SOFTWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
42 |
5.1 ST6 ARCHITECTURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 5.2 ADDRESSING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 5.3 INSTRUCTION SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
6 ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
6.1 ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 6.2 RECOMMENDED OPERATING CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 6.3 DC ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 6.4 AC ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 6.5 A/D CONVERTER CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 6.6 TIMER CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
7 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
7.1 PACKAGE MECHANICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 7.2 .ORDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
ST62P15C/P25C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
1 GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
62 |
||
1.1 |
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
62 |
|
1.2 |
ORDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
62 |
|
|
1.2.1 |
Transfer of Customer Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
62 |
|
1.2.2 |
Listing Generation and Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
62 |
ST6215C/25C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
1 GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
66 |
||
1.1 |
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
66 |
|
1.2 |
ROM READOUT PROTECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
66 |
|
1.3 |
ORDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
68 |
|
|
1.3.1 |
Transfer of Customer Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
68 |
|
1.3.2 |
Listing Generation and Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
68 |
3/70
ST62T15C/T25C/E25C
1 GENERAL DESCRIPTION
1.1 INTRODUCTION
The ST62T15C,T25C and ST62E25C devices are low cost members of the ST62xx 8-bit HCMOS family of microcontrollers, which is targeted at low to medium complexity applications. All ST62xx devices are based on a building block approach: a common core is surrounded by a number of onchip peripherals.
The ST62E25C is the erasable EPROM version of the ST62T15C,T25C device, which may be used to emulate the ST62T15C,T25C device, as well as the respective ST6215C,25C ROM devices.
OTP and EPROM devices are functionally identical. The ROM based versions offer the same functionality selecting as ROM options the options de-
Figure 1. Block Diagram
fined in the programmable option bytes of the OTP/EPROM versions.
OTP devices offer all the advantages of user programmability at low cost, which make them the ideal choice in a wide range of applications where frequent code changes, multiple code versions or last minute programmability are required.
These compact low-cost devices feature a Timer comprising an 8-bit counter and a 7-bit programmable prescaler, an 8-bit A/D Converter with 16 analog inputs and a Digital Watchdog timer, making them well suited for a wide range of automotive, appliance and industrial applications.
TEST/VPP |
TEST |
NMI |
INTERRUP T |
|
PROGRAM |
|
MEMORY: |
|
1836 Bytes |
|
ST62T15C |
|
3884 Bytes |
|
ST62T25C, E25C |
PC
STACK LEVEL 1
STACK LEVEL 2
STACK LEVEL 3
STACK LEVEL 4
STACK LEVEL 5
STACK LEVEL 6
8-BIT
A/D CONVERTER
DATA ROM
USER
SELECTAB LE
DATA RAM
64 Bytes
8 BIT CORE
POWER OSCILLATOR RESET SUPPLY
VDD VSS OSCin OSCout RESET
PORT A |
PA0..PA 3 |
(20mA Sink) |
|
PA4..PA 7 |
/ Ain |
||
|
|||
PORT B |
PB0..PB7 / Ain |
||
PORT C |
PC4..PC7 / Ain |
TIMER |
TIMER |
DIGITAL
WATCHDOG
4/70
1.2 PIN DESCRIPTIONS
VDD and VSS. Power is supplied to the MCU via these two pins. VDD is the power connection and VSS is the ground connection.
OSCin and OSCout. These pins are internally connected to the on-chip oscillator circuit. A quartz crystal, a ceramic resonator or an external clock signal can be connected between these two pins. The OSCin pin is the input pin, the OSCout pin is the output pin.
RESET. The active-low RESET pin is used to restart the microcontroller. Internal pull-up is provided at this pin.
TEST/VPP. The TEST must be held at VSS for normal operation. If TEST pin is connected to a +12.5V level during the reset phase, the EPROM programming Mode is entered.
NMI. The NMI pin provides the capability for asynchronous interruption, by applying an external non maskable interrupt to the MCU. The NMI input is falling edge sensitive. The user can select as option the availability of an on-chip pull-up at this pin.
TIMER. This is the timer I/O pin. In input mode it is connected to the prescaler and acts as external timer clock input or as control gate input for the internal timer clock. In output mode the timer pin outputs the data bit when a time-out occurs. The user can select as option the availability of an on-chip pull-up at this pin.
PA0-PA7. These 8 lines are organized as one I/O port (A). Each line may be configured under software control as inputs with or without internal pullup resistors, interrupt generating inputs with pullup resistors, open-drain or push-pull outputs. PA0PA3 can also sink 20mA for direct LED driving while PA4-PA7 can be programmed as analog in-
ST62T15C/T25C/E25C
puts for the A/D converter.
PB0-PB7. These 8 lines are organized as one I/O port (B). Each line may be configured under software control as inputs with or without internal pullup resistors, interrupt generating inputs with pullup resistors, open-drain or push-pull outputs, or as analog inputs for the A/D converter.
PC4-PC7. These 4 lines are organized as one I/O port (C). Each line may be configured under software control as inputs with or without internal pullup resistors, interrupt generating inputs with pullup resistors, open-drain or push-pull outputs, or as analog inputs for the A/D converter.
Figure 2. ST62T15C,T25C and E25C Pin
Configuration
VDD |
1 |
28 |
VSS |
TIMER |
2 |
27 |
PA0/20mA Sink |
OSCin |
3 |
26 |
PA1/20mA Sink |
OSCout |
4 |
25 |
PA2/20mA Sink |
NMI |
5 |
24 |
PA3/20mA Sink |
Ain/PC7 |
6 |
23 |
PA4/Ain |
Ain/PC6 |
7 |
22 |
PA5/Ain |
Ain/PC5 |
8 |
21 |
PA6/Ain |
Ain/PC4 |
9 |
20 |
PA7/Ain |
VPP/TEST |
10 |
19 |
PB0/Ain |
RESET |
11 |
18 |
PB1/Ain |
Ain/PB7 |
12 |
17 |
PB2/Ain |
Ain/PB6 |
13 |
16 |
PB3/Ain |
Ain/PB5 |
14 |
15 |
PB4/Ain |
5/70
ST62T15C/T25C/E25C
1.3 MEMORY MAP
1.3.1 Introduction
The MCU operates in three separate memory spaces: Program space, Data space, and Stack space. Operation in these three memory spaces is described in the following paragraphs.
Figure 3. Memory Addressing Diagram
PROGRAM SPACE
0000h
0-63
PROGRAM
MEMORY
0FF0h
INTERRUPT &
RESET VECTORS
0FFFh
Briefly, Program space contains user program code in OTP and user vectors; Data space contains user data in RAM and in OTP, and Stack space accommodates six levels of stack for subroutine and interrupt service routine nesting.
|
DATA SPACE |
000h |
|
|
RAM / EEPROM |
|
BANKING AREA |
03Fh |
|
040h |
|
|
DATA READ-ONLY |
|
MEMORY WINDOW |
07Fh |
|
080h |
X REGISTER |
081h |
Y REGISTER |
082h |
V REGISTER |
083h |
W REGISTER |
084h |
RAM |
|
|
0C0h |
DATA READ-ONLY |
|
MEMORY |
|
WINDOW SELECT |
|
DATA RAM |
|
BANK SELECT |
0FFh |
ACCUMULATOR |
6/70
MEMORY MAP (Cont'd)
1.3.2 Program Space
Program Space comprises the instructions to be executed, the data required for immediate addressing mode instructions, the reserved factory test area and the user vectors. Program Space is addressed via the 12-bit Program Counter register (PC register) Program Memory Protection.
The Program Memory in OTP or EPROM devices can be protected against external readout of memory by selecting the READOUT PROTECTION option in the option byte.
Figure 4. Program Memory Map
ST62T15C
0000h
NOT IMPLEMENTED
07FFh
0800h
RESERVED*
087Fh
0880h
|
USER |
|
|
PROGRAM MEMORY |
|
|
(OTP) |
|
|
1824 BYTES |
|
0F9Fh |
|
|
0FA0h |
RESERVED* |
|
0FEFh |
||
|
||
0FF0h |
INTERRUPT VECTORS |
|
0FF7h |
||
|
||
0FF8h |
RESERVED |
|
0FFBh |
||
|
||
0FFCh |
NMI VECTOR |
|
0FFDh |
||
|
||
0FFEh |
USER RESET VECTOR |
|
0FFFh |
|
(*) Reserved areas should be filled with 0FFh
ST62T15C/T25C/E25C
In the EPROM parts, READOUT PROTECTION option can be disactivated only by U.V. erasure that also results into the whole EPROM context erasure.
Note: Once the Readout Protection is activated, it is no longer possible, even for STMicroelectronics, to gain access to the OTP contents. Returned parts with a protection set can therefore not be accepted.
ST62T25C, E25C
0000h
RESERVED*
07Fh
080h
USER
PROGRAM MEMORY
(OTP/EPROM)
3872 BYTES
0F9Fh |
|
|
0FA0h |
RESERVED* |
|
0FEFh |
||
|
||
0FF0h |
INTERRUPT VECTORS |
|
0FF7h |
||
|
||
0FF8h |
RESERVED* |
|
0FFBh |
|
|
0FFCh |
NMI VECTOR |
|
0FFDh |
||
|
||
0FFEh |
USER RESET VECTOR |
|
0FFFh |
|
7/70
ST62T15C/T25C/E25C
MEMORY MAP (Cont'd)
1.3.3 Data Space
Data Space accommodates all the data necessary for processing the user program. This space comprises the RAM resource, the processor core and peripheral registers, as well as read-only data such as constants and look-up tables in OTP/ EPROM.
1.3.3.1 Data ROM
All read-only data is physically stored in program memory, which also accommodates the Program Space. The program memory consequently contains the program code to be executed, as well as the constants and look-up tables required by the application.
The Data Space locations in which the different constants and look-up tables are addressed by the processor core may be thought of as a 64-byte window through which it is possible to access the read-only data stored in OTP/EPROM.
1.3.3.2 Data RAM
In ST6225 devices, the data space includes 60 bytes of RAM, the accumulator (A), the indirect registers (X), (Y), the short direct registers (V), (W), the I/O port registers, the peripheral data and control registers, the interrupt option register and the Data ROM Window register (DRW register).
1.3.4 Stack Space
Stack space consists of six 12-bit registers which are used to stack subroutine and interrupt return addresses, as well as the current program counter contents.
Table 1. ST6225 Data Memory Space
000h
RESERVED
|
03Fh |
|
DATA ROM WINDOW AREA |
040h |
|
|
||
64 BYTES |
07Fh |
|
|
||
X REGISTER |
080h |
|
Y REGISTER |
081h |
|
V REGISTER |
082h |
|
W REGISTER |
083h |
|
DATA RAM 60 BYTES |
084h |
|
0BFh |
||
|
||
PORT A DATA REGISTE R |
0C0h |
|
PORT B DATA REGISTE R |
0C1h |
|
PORT C DATA REGISTER |
0C2h |
|
RESERVED |
0C3h |
|
PORT A DIRECTION REGISTER |
0C4h |
|
PORT B DIRECTION REGISTER |
0C5h |
|
PORT C DIRECTI ON REGISTER |
0C6h |
|
RESERVED |
0C7h |
|
INTERRUPT OPTION REGISTE R |
0C8h* |
|
DATA ROM WINDOW REGISTER |
0C9h* |
|
RESERVED |
0CAh |
|
0CBh |
||
|
||
PORT A OPTION REGISTER |
0CCh |
|
PORT B OPTION REGISTER |
0CDh |
|
PORT C OPTION REGISTE R |
0CEh |
|
RESERVED |
0CFh |
|
A/D DATA REGISTER |
0D0h |
|
A/D CONTROL REGISTER |
0D1h |
|
TIMER PRESCALER REGISTER |
0D2h |
|
TIMER COUNTER REGISTE R |
0D3h |
|
TIMER STATUS CONTROL REGISTER |
0D4h |
|
|
0D5h |
|
RESERVED |
0D6h |
|
|
0D7h |
|
WATCHDOG REGISTER |
0D8h |
|
RESERVED |
0D9h |
|
0FEh |
||
|
||
ACCUMULATOR |
0FFh |
* WRITE ONLY REGISTER
8/70
ST62T15C/T25C/E25C
MEMORY MAP (Cont'd)
1.3.5 Data Window Register (DWR)
The Data read-only memory window is located from address 0040h to address 007Fh in Data space. It allows direct reading of 64 consecutive bytes located anywhere in program memory, between address 0000h and 0FFFh (top memory address depends on the specific device). All the program memory can therefore be used to store either instructions or read-only data. Indeed, the window can be moved in steps of 64 bytes along the program memory by writing the appropriate code in the Data Window Register (DWR).
The DWR can be addressed like any RAM location in the Data Space, it is however a write-only register and therefore cannot be accessed using singlebit operations. This register is used to position the 64-byte read-only data window (from address 40h to address 7Fh of the Data space) in program memory in 64-byte steps. The effective address of the byte to be read as data in program memory is obtained by concatenating the 6 least significant bits of the register address given in the instruction (as least significant bits) and the content of the DWR register (as most significant bits), as illustrated in Figure 5 below. For instance, when addressing location 0040h of the Data Space, with 0 loaded in the DWR register, the physical location addressed in program memory is 00h. The DWR register is not cleared on reset, therefore it must be written to prior to the first access to the Data readonly memory window area.
Data Window Register (DWR)
Address: 0C9h Ð Write Only
7 |
0 |
-- DWR5 DWR4 DWR3 DWR2 DWR1 DWR0
Bits 6, 7 = Not used.
Bit 5-0 = DWR5-DWR0: Data read-only memory Window Register Bits. These are the Data readonly memory Window bits that correspond to the upper bits of the data read-only memory space.
Caution: This register is undefined on reset. Neither read nor single bit instructions may be used to address this register.
Note: Care is required when handling the DWR register as it is write only. For this reason, the DWR contents should not be changed while executing an interrupt service routine, as the service routine cannot save and then restore the register's previous contents. If it is impossible to avoid writing to the DWR during the interrupt service routine, an image of the register must be saved in a RAM location, and each time the program writes to the DWR, it must also write to the image register. The image register must be written first so that, if an interrupt occurs between the two instructions, the DWR is not affected.
Figure 5. Data read-only memory Window Memory Addressing
DATA ROM |
13 |
12 |
11 10 9 |
8 |
7 |
6 |
5 |
4 |
3 |
2 |
1 |
0 PROGRAM SPACE ADDRESS |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
READ |
|
WINDOW REGISTER 7 |
6 |
5 |
4 |
3 |
2 |
1 |
0 |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|||||||||
CONTENTS |
|
|
|
|
|
|
|
|
5 |
4 |
3 |
2 |
1 |
0 |
DATA SPACE ADDRESS |
(DWR) |
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
: |
|
|
|
|
|
|
|
|
0 |
1 |
|
|
|
|
|
|
40h-7Fh |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IN INSTRUCTION |
Example: |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DWR=28h |
|
|
1 |
0 |
1 |
0 |
0 |
0 |
|
|
|
|
|
|
DATA SPACE ADDRESS |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
0 |
1 |
0 |
1 |
1 |
0 |
0 |
1 |
|
|
|
|
|
|
|
|
: |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
59h |
ROM |
|
|
1 |
0 |
1 |
0 |
0 |
0 |
0 |
1 |
1 |
0 |
0 |
1 |
|
ADDRESS:A19h |
|
|
|
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
VR01573C |
9/70
ST62T15C/T25C/E25C
1.4 PROGRAMMING MODES
1.4.1 Option Bytes
The two Option Bytes allow configuration capability to the MCUs. Option byte's content is automatically read, and the selected options enabled, when the chip reset is activated.
It can only be accessed during the programming mode. This access is made either automatically (copy from a master device) or by selecting the OPTION BYTE PROGRAMMING mode of the programmer.
The option bytes are located in a non-user map. No address has to be specified.
EPROM Code Option Byte (LSB)
7 |
|
|
|
|
|
0 |
PRO- |
OSCIL - |
- |
NMI |
TIM |
WDACT |
OS- |
TECT |
PULL |
PULL |
GEN |
EPROM Code Option Byte (MSB)
15 |
|
|
|
|
|
|
8 |
|
- |
- |
- |
- |
- |
- |
EXTC- |
LVD |
|
NTL |
||||||||
|
|
|
|
|
|
|
D15-D10. Reserved. Must be cleared
EXTCNTL. External STOP MODE control.. When EXTCNTL is high, STOP mode is available with watchdog active by setting NMI pin to one.. When EXTCNTL is low, STOP mode is not available with the watchdog active.
LVD. LVD RESET enable.When this bit is set, safe RESET is performed by MCU when the supply voltage is too low. When this bit is cleared, only power-on reset or external RESET are active.
PROTECT. Readout Protection. This bit allows the protection of the software contents against piracy. When the bit PROTECT is set high, readout of the OTP contents is prevented by hardware.. When this bit is low, the user program can be read.
OSCIL. Oscillator selection. When this bit is low, the oscillator must be controlled by a quartz crystal, a ceramic resonator or an external frequency. When it is high, the oscillator must be controlled by an RC network, with only the resistor having to be externally provided.
D5-D4. Reserved. Must be cleared to zero.
NMI PULL. NMI Pull-Up. This bit must be set high to configure the NMI pin with a pull-up resistor. When it is low, no pull-up is provided.
TIM PULL.TIM Pull-Up. This bit must be set high to configure the TIMER pin with a pull-up resistor. When it is low, no pull-up is provided.
WDACT. This bit controls the watchdog activation. When it is high, hardware activation is selected. The software activation is selected when WDACT is low.
OSGEN. Oscillator Safe Guard. This bit must be set high to enable the Oscillator Safe Guard. When this bit is low, the OSG is disabled.
The Option byte is written during programming either by using the PC menu (PC driven Mode) or automatically (stand-alone mode)
10/70
PROGRAMMING MODES (Cont'd)
1.4.2 Program Memory
EPROM/OTP programming mode is set by a +12.5V voltage applied to the TEST/VPP pin. The programming flow of the ST62T15C,T25C/E25C is described in the User Manual of the EPROM Programming Board.
Table 2. ST62T15C Program Memory Map
Device Address |
Description |
0000h-087Fh |
Reserved |
0880h-0F9Fh |
User ROM |
0FA0h-0FEFh |
Reserved |
0FF0h-0FF7h |
Interrupt Vectors |
0FF8h-0FFBh |
Reserved |
0FFCh-0FFDh |
NMI Interrupt Vector |
0FFEh-0FFFh |
Reset Vector |
Table 3. ST62T25C,E25C Program Memory Map
Device Address |
Description |
0000h-007Fh |
Reserved |
0080h-0F9Fh |
User ROM |
0FA0h-0FEFh |
Reserved |
0FF0h-0FF7h |
Interrupt Vectors |
0FF8h-0FFBh |
Reserved |
0FFCh-0FFDh |
NMI Interrupt Vector |
0FFEh-0FFFh |
Reset Vector |
ST62T15C/T25C/E25C
Note: OTP/EPROM devices can be programmed with the development tools available from STMicroelectronics (ST62E2X-EPB or ST622X-KIT).
1.4.3 EPROM Erasing
The EPROM of the windowed package of the MCUs may be erased by exposure to Ultra Violet light. The erasure characteristic of the MCUs is such that erasure begins when the memory is exposed to light with a wave lengths shorter than approximately 4000Å. It should be noted that sunlights and some types of fluorescent lamps have wavelengths in the range 3000-4000Å.
It is thus recommended that the window of the MCUs packages be covered by an opaque label to prevent unintentional erasure problems when testing the application in such an environment.
The recommended erasure procedure of the MCUs EPROM is the exposure to short wave ultraviolet light which have a wave-length 2537A. The integrated dose (i.e. U.V. intensity x exposure time) for erasure should be a minimum of 30Wsec/cm2. The erasure time with this dosage is approximately 30 to 40 minutes using an ultraviolet lamp with 12000μW/cm2 power rating. The ST62E25C should be placed within 2.5cm (1Inch) of the lamp tubes during erasure.
11/70
ST62T15C/T25C/E25C
2 CENTRAL PROCESSING UNIT
2.1 INTRODUCTION
The CPU Core of ST6 devices is independent of the I/O or Memory configuration. As such, it may be thought of as an independent central processor communicating with on-chip I/O, Memory and Peripherals via internal address, data, and control buses. In-core communication is arranged as shown in Figure 6; the controller being externally linked to both the Reset and Oscillator circuits, while the core is linked to the dedicated on-chip peripherals via the serial data bus and indirectly, for interrupt purposes, through the control registers.
2.2 CPU REGISTERS
The ST6 Family CPU corefeatures six registers and three pairs of flags available to the programmer. These are described in the following paragraphs.
Accumulator (A). The accumulator is an 8-bit general purpose register used in all arithmetic calculations, logical operations, and data manipulations. The accumulator can be addressed in Data space as a RAM location at address FFh. Thus the ST6 can manipulate the accumulator just like any other register in Data space.
Figure 6. ST6 Core Block Diagram
Indirect Registers (X, Y). These two indirect registers are used as pointers to memory locations in Data space. They are used in the register-indirect addressing mode. These registers can be addressed in the data space as RAM locations at addresses 80h (X) and 81h (Y). They can also be accessed with the direct, short direct, or bit direct addressing modes. Accordingly, the ST6 instruction set can use the indirect registers as any other register of the data space.
Short Direct Registers (V, W). These two registers are used to save a byte in short direct addressing mode. They can be addressed in Data space as RAM locations at addresses 82h (V) and 83h (W). They can also be accessed using the direct and bit direct addressing modes. Thus, the ST6 instruction set can use the short direct registers as any other register of the data space.
Program Counter (PC). The program counter is a 12-bit register which contains the address of the next ROM location to be processed by the core. This ROM location may be an opcode, an operand, or the address of an operand. The 12-bit length allows the direct addressing of 4096 bytes in Program space.
|
|
0,01 TO 8MHz |
|
|
|
|
RESET |
OSCin |
OSCout |
|
|
|
|
|
|
||
|
|
|
INTERRUPTS |
||
|
|
CONTROLLER |
|
|
|
|
|
|
|
|
DATA SPACE |
|
|
FLAG |
CONTROL |
|
|
|
OPCODE |
SIGNALS |
|
DATA |
|
|
VALUES |
ADDRESS /READ LINE |
|
||
|
|
|
|||
|
|
2 |
|
|
RAM/EEPR OM |
|
|
|
|
|
|
PROGRAM |
|
|
|
|
DATA |
ROM/EPROM |
|
|
ADDRESS |
|
|
|
|
256 |
ROM/EPROM |
||
|
|
|
DECODER |
|
|
|
|
|
|
|
|
|
|
A-DATA B-DATA |
|
DEDICAT IONS |
|
|
|
|
|
|
|
|
|
|
|
|
ACCUMULATOR |
12 |
Program Counter |
|
|
|
|
and |
FLAGS |
|
|
|
|
|
6 LAYER STACK |
ALU |
|
|
RESULTS TO DATA SPACE (WRITE LINE)
VR01811
12/70
CPU REGISTERS (Cont'd)
However, if the program space contains more than 4096 bytes, the additional memory in program space can be addressed by using the Program Bank Switch register.
The PC value is incremented after reading the address of the current instruction. To execute relative jumps, the PC and the offset are shifted through the ALU, where they are added; the result is then shifted back into the PC. The program counter can be changed in the following ways:
-JP (Jump) instructionPC=Jump address
-CALL instructionPC= Call address
-Relative Branch Instruction.PC= PC +/- offset
- Interrupt |
PC=Interrupt vector |
- Reset |
PC= Reset vector |
-RET & RETI instructionsPC= Pop (stack)
-Normal instructionPC= PC + 1
Flags (C, Z). The ST6 CPU includes three pairs of flags (Carry and Zero), each pair being associated with one of the three normal modes of operation: Normal mode, Interrupt mode and Non Maskable Interrupt mode. Each pair consists of a CARRY flag and a ZERO flag. One pair (CN, ZN) is used during Normal operation, another pair is used during Interrupt mode (CI, ZI), and a third pair is used in the Non Maskable Interrupt mode (CNMI, ZNMI).
The ST6 CPU uses the pair of flags associated with the current mode: as soon as an interrupt (or a Non Maskable Interrupt) is generated, the ST6 CPU uses the Interrupt flags (resp. the NMI flags) instead of the Normal flags. When the RETI instruction is executed, the previously used set of flags is restored. It should be noted that each flag set can only be addressed in its own context (Non Maskable Interrupt, Normal Interrupt or Main routine). The flags are not cleared during context switching and thus retain their status.
The Carry flag is set when a carry or a borrow occurs during arithmetic operations; otherwise it is cleared. The Carry flag is also set to the value of the bit tested in a bit test instruction; it also participates in the rotate left instruction.
The Zero flag is set if the result of the last arithmetic or logical operation was equal to zero; otherwise it is cleared.
Switching between the three sets of flags is performed automatically when an NMI, an interrupt or a RETI instructions occurs. As the NMI mode is
ST62T15C/T25C/E25C
automatically selected after the reset of the MCU, the ST6 core uses at first the NMI flags.
Stack. The ST6 CPU includes a true LIFO hardware stack which eliminates the need for a stack pointer. The stack consists of six separate 12-bit RAM locations that do not belong to the data space RAM area. When a subroutine call (or interrupt request) occurs, the contents of each level are shifted into the next higher level, while the content of the PC is shifted into the first level (the original contents of the sixth stack level are lost). When a subroutine or interrupt return occurs (RET or RETI instructions), the first level register is shifted back into the PC and the value of each level is popped back into the previous level. Since the accumulator, in common with all other data space registers, is not stored in this stack, management of these registers should be performed within the subroutine. The stack will remain in its ªdeepestº position if more than 6 nested calls or interrupts are executed, and consequently the last return address will be lost. It will also remain in its highest position if the stack is empty and a RET or RETI is executed. In this case the next instruction will be executed.
Figurel 7. ST6 CPU Programming Mode
INDEX |
b7 |
X REG. POINTER |
b0 |
SHORT |
||
|
|
|
|
|||
REGISTER |
|
|
|
|
||
b7 |
Y REG. POINTER |
b0 |
DIRECT |
|||
|
||||||
|
ADDRESSING |
|||||
|
|
|
|
|
||
|
b7 |
V REGISTER |
b0 |
MODE |
||
|
|
|||||
|
b7 |
W REGISTER |
b0 |
|
||
|
b7 |
ACCUM ULATO R |
b0 |
|
||
b11 |
PROGRAM COUNTER |
|
b0 |
|
||
|
SIX LEVELS |
|
|
|
||
|
STACK REGISTER |
|
|
|
||
NORMAL FLAGS |
|
C |
Z |
|
||
INTERRUPT FLAGS |
C |
Z |
|
|||
NMI FLAGS |
|
C |
Z |
|
||
|
|
|
|
|
VA000423 |
13/70
ST62T15C/T25C/E25C
3 CLOCKS, RESET, INTERRUPTS AND POWER SAVING MODES
3.1 CLOCK SYSTEM
The MCU features a Main Oscillator which can be driven by an external clock, or used in conjunction with an AT-cut parallel resonant crystal or a suitable ceramic resonator, or with an external resistor
(RNET). In addition, a Low Frequency Auxiliary Oscillator (LFAO) can be switched in for security rea-
sons, to reduce power consumption, or to offer the benefits of a back-up clock system.
Figure 8. Oscillator Configurations
CRYSTAL/RES ONATOR CLOCK
CRYSTAL/RESON ATOR option
ST6xxx
The Oscillator Safeguard (OSG) option filters spikes from the oscillator lines, provides access to the LFAO to provide a backup oscillator in the event of main oscillator failure and also automatically limits the internal clock frequency (fINT) as a function of VDD, in order to guarantee correct operation. These functions are illustrated in Figure 9, Figure 10, Figure 11 and Figure 12.
OSCin OSCout
CL1n |
CL2 |
Figure 8 illustrates various possible oscillator configurations using an external crystal or ceramic resonator, an external clock input, an external resistor (RNET), or the lowest cost solution using only the LFAO. CL1 an CL2 should have a capacitance in the range 12 to 22 pF for an oscillator frequency in the 4-8 MHz range.
The internal MCU clock frequency (fINT) is divided by 12 to drive the Timer, the A/D converter and the Watchdog timer, and by 13 to drive the CPU core, as may be seen in Figure 11.
With an 8MHz oscillator frequency, the fastest machine cycle is therefore 1.625μs.
A machine cycle is the smallest unit of time needed to execute any operation (for instance, to increment the Program Counter). An instruction may require two, four, or five machine cycles for execution.
EXTERNAL CLOCK CRYSTAL/RESON ATOR option
ST6xxx
OSCin OSCout
NC
RC NETW ORK
RC NETW ORK option
ST6xxx
OSCin OSCout
3.1.1 Main Oscillator
The oscillator configuration may be specified by selecting theappropriate option.When the CRYSTAL/ RESONATORoption isselected, itmustbeusedwith a quartz crystal, a ceramic resonator or an external signal providedonthe OSCinpin.When theRCNETWORK option is selected, the system clock is generated by an external resistor.
The main oscillator can be turned off (when the OSG ENABLED option is selected) by setting the OSCOFF bit of the ADC Control Register. The Low Frequency Auxiliary Oscillator is automatically started.
NC
RNET
INTEGRA TED CLOCK CRYSTAL/RESON ATOR option
OSG ENABLED option
ST6xxx
OSCin OSCout
NC
14/70
CLOCK SYSTEM (Cont'd)
Turning on the main oscillator is achieved by resetting the OSCOFF bit of the A/D Converter Control Register or by resetting the MCU. Restarting the main oscillator implies a delay comprising the oscillator start up delay period plus the duration of the software instruction at fLFAO clock frequency.
3.1.2Low Frequency Auxiliary Oscillator (LFAO)
The Low Frequency Auxiliary Oscillator has three main purposes. Firstly, it can be used to reduce power consumption in non timing critical routines. Secondly, it offers a fully integrated system clock, without any external components. Lastly, it acts as a safety oscillator in case of main oscillator failure.
This oscillator is available when the OSG ENABLED option is selected. In this case, it automatically starts one of its periods after the first missing edge from the main oscillator, whatever the reason (main oscillator defective, no clock circuitry provided, main oscillator switched off...).
User code, normal interrupts, WAIT and STOP instructions, are processed as normal, at the reduced fLFAO frequency. The A/D converter accuracy is decreased, since the internal frequency is below 1MHz.
At power on, the Low Frequency Auxiliary Oscillator starts faster than the Main Oscillator. It therefore feeds the on-chip counter generating the POR delay until the Main Oscillator runs.
The Low Frequency Auxiliary Oscillator is automatically switched off as soon as the main oscillator starts.
ADCR
Address: 0D1h Ð |
Read/Write |
|
|
|
|||
7 |
|
|
|
|
|
|
0 |
ADCR |
ADCR |
ADCR |
ADCR |
ADCR |
OSC |
ADCR |
ADCR |
7 |
6 |
5 |
4 |
3 |
OFF |
1 |
0 |
Bit 7-3, 1-0= ADCR7-ADCR3, ADCR1-ADCR0:
ADC Control Register. These bits are not used.
Bit 2 = OSCOFF. When low, this bit enables main oscillator to run. The main oscillator is switched off when OSCOFF is high.
3.1.3 Oscillator Safe Guard
The Oscillator Safe Guard (OSG) affords drastically increased operational integrity in ST62xx devices. The OSG circuit provides three basic func-
ST62T15C/T25C/E25C
tions: it filters spikes from the oscillator lines which would result in over frequency to the ST62 CPU; it gives access to the Low Frequency Auxiliary Oscillator (LFAO), used to ensure minimum processing in case of main oscillator failure, to offer reduced power consumption or to provide a fixed frequency low cost oscillator; finally, it automatically limits the internal clock frequency as a function of supply voltage, in order to ensure correct operation even if the power supply should drop.
The OSG is enabled or disabled by choosing the relevant OSG option. It may be viewed as a filter whose cross-over frequency is device dependent.
Spikes on the oscillator lines result in an effectively increased internal clock frequency. In the absence of an OSG circuit, this may lead to an over frequency for a given power supply voltage. The OSG filters out such spikes (as illustrated in Figure 9). In all cases, when the OSG is active, the maximum internal clock frequency, fINT, is limited to fOSG, which is supply voltage dependent. This relationship is illustrated in Figure 12.
When the OSG is enabled, the Low Frequency Auxiliary Oscillator may be accessed. This oscillator starts operating after the first missing edge of the main oscillator (see Figure 10).
Over-frequency, at a given power supply level, is seen by the OSG as spikes; it therefore filters out some cycles in order that the internal clock frequency of the device is kept within the range the particular device can stand (depending on VDD), and below fOSG: the maximum authorised frequency with OSG enabled.
Note. The OSG should be used wherever possible as it provides maximum safety. Care must be taken, however, as it can increase power consumption and reduce the maximum operating frequency to fOSG.
Warning: Care has to be taken when using the OSG, as the internal frequency is defined between a minimum and a maximum value and is not accurate.
For precise timing measurements, it is not recommended to use the OSG and it should not be enabled in applications that use the SPI or the UART.
It should also be noted that power consumption in Stop mode is higher when the OSG is enabled (around 50μA at nominal conditions and room temperature).
15/70
ST62T15C/T25C/E25C
CLOCK SYSTEM (Cont'd)
Figure 9. OSG Filtering Principle
(1)
(2)
(3)
(4)
(1)Maximum Frequency for the device to work correctly
(2)Actual Quartz Crystal Frequency at OSCin pin
(3)Noise from OSCin
(4)Resulting Internal Frequency
Figure 10. OSG Emergency Oscillator Principle
Main
Oscillator
Emergency
Oscillator
Internal
Frequency
VR001932
VR001933
16/70
ST62T15C/T25C/E25C
CLOCK SYSTEM (Cont'd)
Figure 11. Clock Circuit Block Diagram
|
|
|
POR |
|
|
: 13 |
Core |
|
OSG |
|
|
|
|
|
TIMER 1 |
MAIN |
M |
fINT |
Watchdog |
|
U |
: 12 |
|
OSCILLATOR
X
LFAO
: 1
Main Oscillator off
Figure 12. Maximum Operating Frequency (fMAX) versus Supply Voltage (VDD)
Maximum FREQUENCY (MHz) |
|
|
|
|
|
||
8 |
|
|
|
|
|
|
|
7 |
NOT |
4 |
|
|
|
|
|
6 |
|
|
3 |
|
|
|
|
|
ISFUNCTIONALITY GUARANTEED AREATHISIN |
|
|
|
|
fOSG |
|
|
|
|
|
|
|
|
|
5 |
|
|
|
|
|
|
|
4 |
|
|
|
2 |
|
fOSG Min |
|
|
|
|
|
|
|
|
|
3 |
|
|
|
|
|
|
|
2 |
|
|
|
|
|
|
|
|
|
|
|
1 |
|
|
|
1 |
3 |
|
|
|
|
|
|
2.5 |
3.6 |
4 |
4.5 |
5 |
5.5 |
6 |
SUPPLY VOLTAGE (VDD)
VR01807
Notes:
1.In this area, operation is guaranteed at the quartz crystal frequency.
2.When the OSG is disabled, operation in this area is guaranteed at the crystal frequency. When the OSG is enabled, operation in this area is guar-
anteed at a frequency of at least fOSG Min.
3. When the OSG is disabled, operation in this
area is guaranteed at the quartz crystal frequency. When the OSG is enabled, access to this area is prevented. The internal frequency is kept a fOSG.
4. When the OSG is disabled, operation in this area is not guaranteed
When the OSG is enabled, access to this area is prevented. The internal frequency is kept at fOSG.
17/70
ST62T15C/T25C/E25C
3.2 RESETS
The MCU can be reset in four ways:
±by the external Reset input being pulled low;
±by Power-on Reset;
±by the digital Watchdog peripheral timing out.
±by Low Voltage Detection (LVD)
3.2.1 RESET Input
The RESET pin may be connected to a device of the application board in order to reset the MCU if required. The RESET pin may be pulled low in RUN, WAIT or STOP mode. This input can be used to reset the MCU internal state and ensure a correct start-up procedure. The pin is active low and features a Schmitt trigger input. The internal Reset signal is generated by adding a delay to the external signal. Therefore even short pulses on the RESET pin are acceptable, provided VDD has completed its rising phase and that the oscillator is running correctly (normal RUN or WAIT modes). The MCU is kept in the Reset state as long as the RESET pin is held low.
If RESET activation occurs in the RUN or WAIT modes, processing of the user program is stopped (RUN mode only), the Inputs and Outputs are configured as inputs with pull-up resistors and the main Oscillator is restarted. When the level on the RESET pin then goes high, the initialization sequence is executed following expiry of the internal delay period.
If RESET pin activation occurs in the STOP mode, the oscillator starts up and all Inputs and Outputs are configured as inputs with pull-up resistors. When the level of the RESET pin then goes high, the initialization sequence is executed following expiry of the internal delay period.
3.2.2 Power-on Reset
The function of the POR circuit consists in waking up the MCU by detecting around 2V a dynamic (rising edge) variation of the VDD Supply. At the beginning of this sequence, the MCU is configured in the Reset state: all I/O ports are configured as inputs with pull-up resistors and no instruction is executed. When the power supply voltage rises to a sufficient level, the oscillator starts to operate, whereupon an internal delay is initiated, in order to allow the oscillator to fully stabilize before executing the first instruction. The initialization sequence
is executed immediately following the internal delay.
To ensure correct start-up, the user should take care that the VDD Supply is stabilized at a sufficient level for the chosen frequency (see recommended operation) before the reset signal is released. In addition, supply rising must start from 0V.
As a consequence, the POR does not allow to supervise static, slowly rising, or falling, or noisy (presenting oscillation) VDD supplies.
An external RC network connected to the RESET pin, or the LVD reset can be used instead to get the best performances.
Figure 13. Reset and Interrupt Processing
RESET
NMI MASK SET
INT LATCH CLEARED ( IF PRESENT )
SELECT
NMI MODE FLAGS
PUT FFEH
ON ADDRESS BUS
YES
IS RESET STILL
PRESENT?
NO
LOAD PC
FROM RESET LOCATIONS
FFE/FFF
FETCH INSTRUCTION
VA000427
18/70
ST62T15C/T25C/E25C
RESETS (Cont'd)
3.2.3 Watchdog Reset
The MCU provides a Watchdog timer function in order to ensure graceful recovery from software upsets. If the Watchdog register is not refreshed before an end-of-count condition is reached, the internal reset will be activated. This, amongst other things, resets the watchdog counter.
The MCU restarts just as though the Reset had been generated by the RESET pin, including the built-in stabilisation delay period.
3.2.4 LVD Reset
The on-chip Low Voltage Detector, selectable as user option, features static Reset when supply voltage is below a reference value. Thanks to this feature, external reset circuit can be removed while keeping the application safety. This SAFE RESET is effective as well in Power-on phase as in power supply drop with different reference val-
ues, allowing hysteresis effect. Reference value in case of voltage drop has been set lower than the reference value for power-on in order to avoid any parasitic Reset when MCU start's running and sinking current on the supply.
As long as the supply voltage is below the reference value, there is a internal and static RESET command. The MCU can start only when the supply voltage rises over the reference value. Therefore, only two operating mode exist for the MCU: RESET active below the voltage reference, and running mode over the voltage reference as shown on the Figure 14, that represents a powerup, power-down sequence.
Note: When the RESET state is controlled by one of the internal RESET sources (Low Voltage Detector, Watchdog, Power on Reset), the RESET pin is tied to low logic level.
Figure 14. LVD Reset on Power-on and Power-down (Brown-out)
VDD
VUp
Vdn
RESET |
RESET |
|
|
|
time |
VR02106A
3.2.5 Application Notes
No external resistor is required between VDD and the Reset pin, thanks to the built-in pull-up device.
Direct external connection of the pin RESET to VDD must be avoided in order to ensure safe behaviour of the internal reset sources (AND.Wired structure).
19/70
ST62T15C/T25C/E25C
RESETS (Cont'd)
3.2.6 MCU Initialization Sequence
When a reset occurs the stack is reset, the PC is loaded with the address of the Reset Vector (located in program ROM starting at address 0FFEh). A jump to the beginning of the user program must be coded at this address. Following a Reset, the Interrupt flag is automatically set, so that the CPU is in Non Maskable Interrupt mode; this prevents the initialisation routine from being interrupted. The initialisation routine should therefore be terminated by a RETI instruction, in order to revert to normal mode and enable interrupts. If no pending interrupt is present at the end of the initialisation routine, the MCU will continue by processing the instruction immediately following the RETI instruction. If, however, a pending interrupt is present, it will be serviced.
Figure 15. Reset and Interrupt Processing
RESET
JP |
JP:2 BYTES/4 CYCLES |
RESET
VECTOR
INITIALIZATION
ROUTINE |
RETI: 1 BYTE/2 CYCLES |
|
|
|
RETI |
VA00181
Figure 16. Reset Block Diagram
VDD |
|
|
ST6 |
fOSC |
|
CK |
INTERNA L |
|
|
|
|
|
|
|
RESET |
RPU |
|
COUNTER |
|
AND. Wired |
|
|
|
1) |
|
|
|
RESD |
|
|
|
RESET |
RESET |
RESET |
|
|
|
|
|
POWER ON RESET |
|
|
|
WATCHD OG RESET |
|
|
|
LVD RESET |
|
|
|
|
|
|
VR02107A |
1) Resistive ESD protection. Value not guaranteed.
20/70
|
|
|
ST62T15C/T25C/E25C |
|
RESETS (Cont'd) |
|
|
|
|
Table 4. Register Reset Status |
|
|
|
|
Register |
Address(es) |
Status |
Comment |
|
Oscillator Control Register |
0DCh |
|
fINT = fOSC; OSG disabled |
|
Port Data Registers |
0C0h to 0C2h |
|
I/O are Input with pull-up |
|
Port Direction Register |
0C4h to 0C6h |
00h |
I/O are Input with pull-up |
|
Port Option Register |
0CCh to 0CEh |
I/O are Input with pull-up |
||
|
||||
Interrupt Option Register |
0C8h |
|
Interrupt disabled |
|
TIMER Status/Control |
0D4h |
|
TIMER disabled |
|
X, Y, V, W, Register |
080H TO 083H |
|
|
|
Accumulator |
0FFh |
|
|
|
Data RAM |
084h to 0BFh |
Undefined |
As written if programmed |
|
Data ROM Window Register |
0C9h |
|
|
|
A/D Result Register |
0D0h |
|
|
|
TIMER Counter Register |
0D3h |
FFh |
|
|
TIMER Prescaler Register |
0D2h |
7Fh |
Max count loaded |
|
Watchdog Counter Register |
0D8h |
FEh |
|
|
A/D Control Register |
0D1h |
40h |
A/D in Standby |
21/70