June 1997
Revised December 1999
FST3244
Octal Bus Switch
General Description
The Fairchild Switch FST3244 provides 8-bits of highspeed CMOS TTL-compatible bus switching in a standard ’244 pin-out. The low on resistance of the switch allows inputs to be connected to outputs without adding propagation delay or generating additional ground bounce noise.
The device is organized as two 4-bit switches with separate OE inputs. When OE is LOW, the switch is ON and Port A is connected to Port B. When OE is HIGH, the switch is OPEN and a high-impedance state exists between the two ports.
Features
■4Ω switch connection between two ports.
■Minimal propagation delay through the switch.
■Low lCC.
■Zero bounce in flow-through mode.
■Control inputs compatible with TTL level.
Ordering Code:
Order Number |
Package Number |
Package Description |
|
|
|
FST3244WM |
M20B |
20-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300 Wide |
|
|
|
FST3244QSC |
MQA20 |
20-Lead Quarter Size Outline Package (QSOP), JEDEC MO-137, 0.150 Wide |
|
|
|
FST3244MTC |
MTC20 |
20-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide |
|
|
|
Devices also available in Tape and Reel. Specify by appending the suffix letter “X” to the ordering code.
Logic Diagram |
Connection Diagram |
|
|
|
|
|
|
|
Truth Table |
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Pin Descriptions |
|
|
|
|
Inputs |
|
|
Inputs/Outputs |
|||||||
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
OE |
1 |
|
OE |
2 |
1A, 1B |
2A, 2B |
|
Pin Name |
Description |
|
|
L |
|
L |
1A = 1B |
2A = 2B |
||||||
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
1, |
|
2 |
Bus Switch Enable |
|
|
L |
|
H |
1A = 1B |
Z |
||
|
|
OE |
OE |
|
|
|
|||||||||
|
|
1A, 2A |
Bus A |
|
|
H |
|
L |
Z |
2A = 2B |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
1B, 2B |
Bus B |
|
|
H |
|
H |
Z |
Z |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Switch Bus Octal FST3244
© 1999 Fairchild Semiconductor Corporation |
DS500021 |
www.fairchildsemi.com |
FST3244
Absolute Maximum Ratings(Note 1) |
Recommended Operating |
||||||||||
Supply Voltage (VCC) |
−0.5V to +7.0V |
Conditions (Note 3) |
|
|
|||||||
|
|
|
|
|
|
|
|
||||
DC Switch Voltage (VS) |
−0.5V to +7.0V |
|
Power Supply Operating (VCC) |
|
4.0V to 5.5V |
||||||
DC Input Voltage (VIN) (Note 2) |
−0.5V to +7.0V |
|
Input Voltage (VIN) |
|
|
0V to 5.5V |
|||||
DC Input Diode Current (lIK) VIN<0V |
|
−50mA |
|
Output Voltage (VOUT) |
|
|
0V to 5.5V |
||||
DC Output (IOUT) Sink Current |
|
128mA |
|
Input Rise and Fall Time (tr, tf) |
|
|
|||||
DC VCC/GND Current (ICC/IGND) |
+/− 100mA |
|
Switch Control Input |
|
|
0nS/V to 5nS/V |
|||||
Storage Temperature Range (TSTG) |
−65°C to +150 °C |
|
Switch I/O |
|
|
|
|
0nS/V to DC |
|||
|
|
|
|
|
Free Air Operating Temperature (TA) |
−40 °C to +85 °C |
|||||
|
|
|
|
Note 1: The Absolute Maximum Ratings are those values beyond which |
|||||||
|
|
|
|
the safety of the device cannot be guaranteed. The device should not be |
|||||||
|
|
|
|
operated at these limits. The parametric values defined in the Electrical |
|||||||
|
|
|
|
Characteristics tables are not guaranteed at the absolute maximum rating. |
|||||||
|
|
|
|
The Recommended Operating Conditions tables will define the conditions |
|||||||
|
|
|
|
for actual device operation. |
|
|
|
||||
|
|
|
|
Note 2: The input and output negative voltage ratings may be exceeded if |
|||||||
|
|
|
|
the input and output diode current ratings are observed. |
|||||||
|
|
|
|
Note 3: Unused control inputs must be held HIGH or LOW. They may not |
|||||||
|
|
|
|
float. |
|
|
|
|
|
||
DC Electrical Characteristics |
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
VCC |
|
TA = −40 °C to +85 °C |
|
|
|
|
|||
Symbol |
Parameter |
|
|
|
|
|
|
Units |
|
Conditions |
|
|
|
(V) |
Min |
|
Typ |
|
Max |
|
|
|
|
|
|
|
(Note 4) |
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
VIK |
Clamp Diode Voltage |
4.5 |
|
|
|
|
−1.2 |
|
V |
IIN = −18mA |
|
VIH |
High Level Input Voltage |
4.0–5.5 |
2.0 |
|
|
|
|
|
V |
|
|
VIL |
Low Level Input Voltage |
4.0–5.5 |
|
|
|
|
0.8 |
|
V |
|
|
II |
Input Leakage Current |
5.5 |
|
|
|
|
±1.0 |
|
μA |
0≤ VIN ≤5.5V |
|
IOZ |
OFF-STATE Leakage Current |
5.5 |
|
|
|
|
±1.0 |
|
μA |
0 ≤A, B ≤VCC |
|
RON |
Switch On Resistance |
4.5 |
|
|
4 |
|
7 |
|
Ω |
VIN = 0V, IIN = 64mA |
|
|
(Note 5) |
4.5 |
|
|
4 |
|
7 |
|
Ω |
VIN = 0V, IIN = 30mA |
|
|
|
4.5 |
|
|
8 |
|
15 |
|
Ω |
VIN = 2.4V, IIN = 15mA |
|
|
|
4.0 |
|
|
11 |
|
20 |
|
Ω |
VIN = 2.4V, IIN = 15mA |
|
ICC |
Quiescent Supply Current |
5.5 |
|
|
|
|
3 |
|
μA |
VIN = VCC or GND, IOUT = 0 |
|
ICC |
Increase in ICC per Input |
5.5 |
|
|
|
|
2.5 |
|
mA |
One input at 3.4V |
|
|
|
|
|
|
|
|
|
|
|
Other inputs at VCC or GND |
|
Note 4: Typical |
values are at VCC = 5.0V and TA = + |
25°C |
|
|
|
|
|
|
|
|
|
Note 5: Measured by the voltage drop between A and B pins at the indicated current through the switch. On resistance is determined by the lower of the voltages on the two (A or B) pins.
www.fairchildsemi.com |
2 |