Motorola MBP854CONNECT, MBP854CONNECT-2, MBP854CONNECT-3, MBP854CONNECT-4 Instruction manual

User’s Guide

Digital Video Baby Monitor With Wi-Fi® Internet Viewing

Models: MBP854CONNECT, MBP854CONNECT-2,

MBP854CONNECT-3, MBP854CONNECT-4

The features described in this User’s Guide are subject to modifications without prior notice.

Welcome...

to your new Motorola Digital Video Baby Monitor!

Thank you for purchasing your new Motorola Digital Video Baby Monitor. Now you can see and hear your baby sleeping in another room or you can monitor your older children in their playroom.

Please retain your original dated sales receipt for your records.

For warranty service of your Motorola product, you will need to provide a copy of your dated sales receipt to confirm warranty status. Registration is not required for warranty coverage.

For product related questions, please call:

US and Canada 1-888-331-3383

Email: [e-mail]

This User's Guide provides you with all the information you need to get the most from your product.

Before you can use the Baby Monitor, we recommend you insert and fully charge the battery in the Parent Unit, so that it continues to work if you disconnect it from the power supply to carry it to another location. Please read the Safety Instructions on page 8 before you install the units.

Got everything?

•1 x Parent Unit

•1 x Baby Unit (Camera)

•1 x Power adapter for the Parent Unit

•1 x Power adapter(s) for the Baby Unit

In multi-camera packs, you will find one or more additional camera units with power adapter units and battery packs.

Overview of the Parent Unit

RESET
16	15	11 12	13	14	21

2		7	20
3		8
4		9	17
5		10	19
6		1	18
1.	Display (LCD screen)	11.	Power Adapter / Battery LED BLUE
2.	Video ON/OFF Key V		when connected to an electrical
	Press to turn ON/OFF the LCD		outlet.
	display		RED when battery low.
3.	Talk Key T	12.	Unit ON/OFF LED (Green)
	Press and hold to speak to your baby 13.		Audio Level LED (Green, Orange,
4.	Up Key +		Red, Red)
	Normal Mode: Tilt Up	14.	Power Key 0
	Menu Mode: Up		Press and Hold to turn the unit ON/
5.	Down Key -		OFF
	Normal Mode: Tilt Down	15.	Volume Key
	Menu Mode: Down		Press -/+ to decrease/increase
6.	Microphone		Volume level on Parent Unit
7.	Menu Key M	16.	Reset Key
	Press to open the Menu options	17.	SD Card socket
8.	OK Key O	18.	Micro USB Socket
9.	Left Key <	19.	Stand
	Normal Mode: Pan Left	20.	Speaker
	Menu Mode: Left	21.	Antenna
10.	Right Key >		Lift the antenna for optimal
	Normal Mode: Pan Right		reception
	Menu Mode: Right

Parent Unit menu icons

Signal Level (4 Levels)

Night Vision Mode (Screen changes to Black/White)

Talk Mode

Battery Level Control (4 Levels)

Pan Left

Pan Right

Tilt Up

Tilt Down

Zoom Level Control (1X, 2X)

Brightness Level Control (8 Levels)

Lullaby Control (5 Song Selections)

Alarm Setting (6h, 4h, 2h, Off)

Temperature Reading (HH ºC / ºF or LL ºC / ºF)

Icon & readings turn RED > 29ºC / 84ºF, and reading display HH ºC / ºF > 36ºC / 97 ºF

Icon & readings turn RED < 14ºC / 57ºF, and reading display LL ºC / ºF < 1ºC / 34 ºF

Cam Control (scan, view, add, delete)

Local Recording (Record, Play)

Set Video On Timer (5 min, 30 min, 60 min)

Time Setting (Date, Time format 12/24 Hour and Time)

Volume Level Control (8 Levels)

SD Card detection

No Baby Unit detected

Overview of Your Baby Unit
	1
	2			8
	3
	4
	5
	6			9
			5V 1.5A	10
	7			11
1.	Light Sensor (for night mode detection)	7.	Speaker
2.	Camera Lens	8.	Antenna
3.	Infrared LEDs (for night vision)	9.	Micro USB socket
4.	Power / Status indicator	10. ON/OFF Switch
5.	Microphone	11. Temperature Sensor
6.	PAIR Button

Important guidelines for installing your Baby Monitor

•To use your Video Monitor Baby and Parent Units together, you must be able to establish a radio link between them, and the range will be affected by environmental conditions.

•Any large metal object, like a refrigerator, a mirror, a filing cabinet, metallic doors or reinforced concrete between the Baby and Parent Unit may block the radio signal.

•The signal strength may also be reduced by other solid structures, like walls, or by radio or electrical equipment, such as TVs, computers, cordless or mobile phones, fluorescent lights or dimmer switches.

•Use of other 2.4 GHz products, such as wireless networks (Wi-Fi® routers), Bluetooth® systems, or microwave ovens, may cause interference with this product, so keep the Baby Monitor away at least 3ft from these types of products, or turn them off if they appear to be causing interference.

•If the signal is weak, try lifting up the Parent Unit Antenna, moving the Parent and/or the Baby Unit to different positions in the rooms.

Table of contents

1.	Safety Instructions.....................................................................................			8
2.	Getting Started........................................................................................			11
	2.1	Baby Unit Power Supply............................................................................		11
	2.2	Parent Unit Power Supply .........................................................................		11
	2.3	Registration (Pairing) ................................................................................		13
3. Using the Baby Monitor...........................................................................				14
	3.1	Setting up ..................................................................................................		14
	3.2	Pan and Tilt ................................................................................................		14
	3.3	Night Vision Mode ....................................................................................		14
	3.4	Talk Mode..................................................................................................		14
	3.5	Video ON/OFF .........................................................................................		14
	3.6	Temperature Display (HH °C / °F or LL °C / °F)......................................		15
4. Parent Unit Menu Options ......................................................................				16
	4.1	Volume	......................................................................................................	16
	4.2	Brightness..................................................................................................		16
	4.3	Lullaby .......................................................................................................		16
	4.4	Zoom .........................................................................................................		16
	4.5	Alarm .........................................................................................................		16
	4.6	Camera ........................................................................................Control		17
		4.6.1 ..................................................................	Add (pair) a camera	17
		4.6.2 ...........................................................................	View a camera	17
		4.6.3 ........................................................................	Delete a camera	18
		4.6.4 ..............................................................................	Scan camera	18
	4.7	Temperature .............................................................................................		18
	4.8	Power Saving ..................................................................................mode		18
	4.9	Video .........................................................................................................		19
	4.10	Time Setting ..............................................................................................		19
5.	Wi-Fi Internet ............................................................................Viewing			20
	5.1	Minimum ..............................................................System Requirements		20
	5.2	Getting .....................................................started - Connecting Devices		21
	5.3	User Account .......................and Camera Setup on Android™ Devices		22
		5.3.1 ......................................	Power ON and Connect the Camera	22
		5.3.2 ..................	Download the Hubble for Motorola Monitors App	22
		5.3.3	Run the Hubble for Motorola Monitors App on
		.....................................................................	Android™ device	23
		5.3.4 ...................................................	Add Camera to your account	24

6	Table of contents

5.4 User Account and Camera Setup:
Working with iPhone®/iPad® ..................................................................		28
5.4.1	Power ON and Connect the Camera ......................................	28
5.4.2	Download the Hubble for Motorola Monitors App ..................	28
5.4.3	Run the Hubble App on your iPhone®/iPad® .........................	29
5.4.4	Add the Camera to your account .............................................	30

5.5Camera Functions:

Working with devices for Android™ .......................................................		35
5.5.1	Connecting the Camera to Power ...........................................	35
5.5.2	Add more cameras ....................................................................	35
5.5.3	Remove a Camera ....................................................................	36
5.5.4	Change your Account Information ..........................................	37
5.5.5	Camera settings ........................................................................	38
5.5.6	General Settings ........................................................................	39
5.5.7	Features of the Hubble App .....................................................	40

5.6Camera Functions:

	Working with devices for iPhone®/iPad® ...............................................		44
	5.6.1	Add more cameras ....................................................................	44
	5.6.2	Remove a Camera ....................................................................	45
	5.6.3	Change your Account Information ..........................................	46
	5.6.4	Camera settings ........................................................................	47
	5.6.5	General settings ........................................................................	47
	5.6.6	Hubble for Motorola Monitors Settings ....................................	49
	5.6.7	Features of the Hubble App .....................................................	50
	5.7 Camera Functions:
	Working with PC/Notebook.....................................................................		54
6.	Disposal of The Device (environment) ...................................................		55
7.	Cleaning ..................................................................................................		56
8.	Help..........................................................................................................		57
9.	General Information ................................................................................		65

ENGLISH

Table of contents	7

1. Safety Instructions

WARNING:

Strangulation Hazard: Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3ft (1m) away). Never use extension cords with AC Adapters. Only use the AC Adapters provided.

8				Safety Instructions

Baby Unit SET UP & USE:

●Determine a location for the Baby Unit that will provide the best view of your baby in his/her crib.

●Place the Baby Unit on a flat surface, such as a dresser, bureau, or shelf or mount the Unit to a wall securely using the keyhole slots under the stand.

●NEVER place the Baby Unit or cords within the crib.

●Do not place the Baby Unit or cords in the crib or within reach of the baby (the unit and cords should be more than 3 feet away).

ENGLISH

WARNING

This digital video Baby Monitor is compliant with all relevant standards regarding electromagnetic fields and is, when handled as described in the User's Guide, safe to use. Therefore, always read the instructions in this User's Guide carefully before using the device.

•Adult assembly is required. Keep small parts away from children when assembling.

•This product is not a toy. Do not allow children to play with it.

•This Baby Monitor is not a substitute for responsible adult supervision.

•Keep this User’s Guide for future reference.

•Do not place the Baby Unit or cords in the crib or within reach of the baby (the unit and cords should be more than 3 feet away)

•Keep the cords out of reach of children.

•Do not cover the Baby Monitor with a towel or blanket.

•Never use extension cords with power adapters. Only use the power adapters provided.

•Test this monitor and all its functions so that you are familiar with it prior to actual use.

•Do not use the Baby Monitor near water.

Safety Instructions	9

•Do not install the Baby Monitor near a heat source.

•Only use the chargers and power adapters provided. Do not use other chargers or power adapters as this may damage the device and battery pack.

•Only insert a battery pack of the same type.

•Do not touch the plug contacts with sharp or metal objects.

CAUTION

Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to their instructions.

The Unit shall be installed and used such that parts of the user’s body other than the hands are maintained at a distance of approximately 8 inches (20 cm) or more.

10	Safety Instructions

2. Getting Started

2.1Baby Unit Power Supply

Power adapter plug

	Switch to turn ON	ON OFF
	the camera

ENGLISH

1.Connect the small plug of the power adapter to the Baby Unit (camera) and the other end to a suitable electrical outlet.

NOTE

Only use the enclosed power adapter (5V DC / 1500mA).

2.Slide the ON/OFF switch to the ON position. The power LED will light up in blue.

3.Slide the ON/OFF switch to the OFF position to turn the Baby Unit off.

2.2Parent Unit Power Supply

IMPORTANT

The Parent Unit is assembled with a built-in rechargeable battery pack (Lithiumion battery 1880mAh), please charge it for 16 hours before use.

1.Connect the micro USB plug of the power adapter to the Parent Unit and the other end to a suitable electrical outlet. Only use the enclosed power adapter (5V DC / 1500mA) with the micro USB plug.

Getting Started	11

2.Press and hold the 0POWER ON/OFF button for 1 second to turn ON the Parent Unit.

3.Once the Baby and Parent Units are switched on, the display on the Parent Unit will show the video captured by the Baby Unit.

4.If there is no connection or you are out of range, the video display will go off and the unit will beep every 5 seconds. Move the Parent Unit closer to the Baby Unit until the link is re-established.

5.Press and hold the 0POWER ON/OFF button, until the progress bar finishes scrolling, to turn OFF the Parent Unit.

NOTE

The battery icon turns RED to indicate that the battery is low, and it gives a beep every 16 seconds. The battery needs to be recharged. The battery pack takes about 12 hours to charge fully.

When charging

1.During power OFF, when adapter is plugged in, an adapter logo will display on screen and a flashing battery logo will display for 15 sec. The Blue LED at the top left corner will light up that indicates that the adapter is plugged in.

2.During power ON, when adapter is plugged in, the battery icon on the screen's top right corner will show that the battery is charging. The Blue LED at the top left corner will light up to indicate that the adapter is plugged in.

12	Getting Started

2.3Registration (Pairing)

The Baby Monitor is pre-registered to your Parent Unit. You do not need to register it again unless the Baby Unit loses its link with the Parent Unit.

To re-register your Baby Unit, or register a new Baby Unit, follow the procedures below:

1.Press the M button of the Parent Unit and the menu bar will pop up.

2.Press the <LEFT button or >RIGHT button until is highlighted, and the del/ add/ view/ scan menu will pop up.

3.Press the +UP button or -DOWN button to select + add, and press the Obutton to confirm.

4.Camera will pop up, press the +UP button or -DOWN button to select the desired Camera and press the O button to start searching for a camera unit. The green audio level LED will flash rapidly while searching.

5.Press the O button to confirm.

6.Press and hold the PAIR button underneath the Baby Unit until the Parent Unit finds the camera, beeps and the video from the camera appears.

NOTE

If a particular Baby Unit was registered previously, registering this current Baby Unit again will overwrite the old registration.

ENGLISH

Getting Started	13

3. Using the Baby Monitor

3.1Setting up

•Place the Baby Unit in a convenient location (e.g. on a table) and point the camera lens towards the area you want to monitor.

•Adjust the Baby Unit's head angle by rotating the camera up, down, left and right until you are satisfied with the image in the Parent Unit.

NOTE

Do not place the Baby Unit within the baby's reach! If there is interference with the picture or sound, try moving the units to different locations, and ensure they are not close to other electrical equipment.

3.2Pan and Tilt

The camera can be remotely controlled from the Parent Unit.

1.Press the +UP button or -DOWN button to tilt upward or downward.

2.Press the <LEFT button or >RIGHT button to pan left or right.

3.3Night Vision Mode

The Baby Unit has 8 high-intensity infrared LEDs for picking up clear images in the dark. When the built-in photo sensor on the top of the unit detects a low level of ambient light, the LEDs will automatically activate and the screen on the Parent Unit will display in black and white. The icon will be displayed at the top of the screen.

3.4Talk Mode

Press and hold the TTALK button on the Parent Unit to talk to your baby through the Baby Unit’s loudspeaker. The T icon will be displayed at the top of the LCD screen.

3.5Video ON/OFF

Press VVIDEO ON/OFF key to turn the LCD display on or off, but still leave the audio monitor on.

14	Using the Baby Monitor

3.6Temperature Display (HH °C / °F or LL °C / °F)

The temperature reading from the temperature sensor at the back of the Baby Unit will be displayed at the top of the LCD screen. The readings will turn RED if the temperature goes above 29°C / 84°F or below 14°C / 57°F. The reading will change to HH °C / °F if the temperature goes above 36°C / 97°F. The reading will change to LL °C / °F if the temperature goes below 1°C / 34°F.

ENGLISH

Using the Baby Monitor	15

4. Parent Unit Menu Options

4.1Volume

1. Press the Volume button - or + to adjust the volume level, the icon will pop up and you can select the desired volume level from level 0~8. (The default volume level setting is level 4.)

4.2	Brightness
1.	Press the Mbutton and the menu bar will pop up.
2.	Press the <LEFT button or >button until	is highlighted.
3.	Press the +UP button or -DOWN button to select the desired brightness
	level from level 1 ~ 8. (The default brightness level setting is level 5.)
4.3	Lullaby
1.	Press the Mbutton and the menu bar will pop up.
2.	Press the <LEFT button or >button until	is highlighted.
3.	Press the +UP button or -DOWN button to select the desired song from
	the 5 lullabies available, or the cycle option to play all 5 songs in turn. If an
	individual song is selected it will only play once. (The default setting is
	lullaby OFF.)
4.	Press Oon the selected lullabies to select the desired song sound level.
4.4	Zoom
1.	Press the Mbutton and the menu bar will pop up.
2.	Press the <LEFT button or >button until	is highlighted.
3.	Press the +UP button or -DOWN button to select the 1X or 2X Zoom.
	(The default setting is 1X.)
4.5	Alarm

1.Press the Mbutton and the menu bar will pop up.

2.Press the <LEFT button or >RIGHT button until is highlighted.

3.Press the +UP button or - DOWN button to select the alarm time (6h, 4h, 2h). (The default setting is Alarm OFF.)

4.If an alarm time is selected, the Parent Unit will beep for about 45 seconds after every 6, 4 or 2 hour period.

16	Parent Unit Menu Options

4.6Camera Control

4.6.1Add (pair) a camera

1.Press the Mbutton and the menu bar will pop up.

2.Press the <LEFT button or >RIGHT button until is highlighted, and

the

del/

add/

view/

scan menu will pop up.

3.Press the +UP button or -DOWN button to select add, and press the Obutton to confirm.

4.Camera will pop up, press the +UP button or -DOWN button to select the desired Camera, and press the Obutton to start searching for a camera unit. The green audio level LED will flash rapidly while searching.

5.Press and hold the PAIR button underneath the Baby Unit until the Parent Unit finds the camera, beeps and the picture from the camera appears.

NOTE

A camera can only be registered to one Parent Unit at any one time.

4.6.2View a camera

1.Press the Mbutton and the menu bar will pop up.

2.Press the <LEFT button or >RIGHT button until is highlighted and

the

del/

add/

view/

scan menu pops up.

3.Press the +UP button or -DOWN button to select view, and press the Obutton to confirm.

4.Camera will pop up, press the +UP button or -DOWN button to select desired Camere, and press the Obutton to view the picture from that camera.

TIP

Quick Method to View Cameras instead of entering into the menu bar. Directly press OK repeatedly to select Camera , scan.

ENGLISH

Parent Unit Menu Options	17

4.6.3Delete a camera

1.Press the Mbutton and the menu bar will pop up.

2.Press the <LEFT button or >RIGHT button until is highlighted, and

the

del/

add/

view/

scan menu will pop up.

3.Press the +UP button or -DOWN button to select del, and press the Obutton to confirm.

4.Camera will pop up, press the +UP button or -DOWN button to select the desired Camera, and press the Obutton to delete that registration.

Note:

You are not allowed to delete the camera if there is only one registered camera in the system.

4.6.4Scan camera

1.Press the Mbutton and the menu bar will pop up.

2.Press the <LEFT button or >RIGHT button until is highlighted, and

the

del/

add/

view/

scan menu will pop up.

3.Press the +UP button or -DOWN button to select scan, and press the Obutton to confirm.

4.The screen will then display images from different registered cameras in a loop of Camera , changing about every 12 seconds.

TIP

Quick Method to View Cameras instead of entering into the menu bar. Directly press OK repeatedly to select Camera , scan.

4.7	Temperature
1.	Press the Mbutton and the menu bar will pop up.
2.	Press the <LEFT button or >RIGHT button until is highlighted.
3.	Press the +UP button or -DOWN button to select °C or °F.
4.8	Power Saving mode

1.Press the Mbutton and the menu bar will pop up.

2.Press the <LEFT button or >RIGHT button until Vis highlighted.

3.Press the +UP button or -DOWN button to select auto video off after 5 mins, 30 mins or 60 mins if not in charging.

18	Parent Unit Menu Options

4.9Video

You can record a video of your baby through this function, the videos will be stored in the SD Memory Card, so please make sure the memory card has enough free space to store the recording data.

1.Press the Mbutton and the menu bar will pop up.

2.Press the <LEFT button or >RIGHT button until is highlighted.

3.Press the +UP button or -DOWN button to select , and press O button to start video recording, thence select press and press O button to stop.

4.Press the +UP button or -DOWN button to select and press O button to play back the video.

Note:

The video format is AVI which you can view on a computer/smartphone/tablet

4.10Time Setting

1.Press the <LEFT button or >RIGHT button until is highlighted and press OButton.

2.Press the <LEFT button or >RIGHT button to move between the settings.

3.Press the +UP button or -DOWN button to set Date, Time format and Time.

ENGLISH

Parent Unit Menu Options	19

5. Wi-Fi Internet Viewing

5.1Minimum System Requirements

Web Portal

•Windows® 7

•Mac OS® 10.7

•Chrome™ 24

•Internet Explorer® 9

•Safari® 6

•Java™ 7

•Firefox® 18.0

•Adobe® Flash® Player 15.0

Android™ System

• Version 4.2 or above

iPhone®/iPad® iOS

• Version 7.0 or above

20	Wi-Fi Internet Viewing

5.2 Getting started - Connecting Devices

How does it work?

View your Camera from any compatible device remotely

When a user tries to access the Camera, our secure server authenticates the user’s identity and permits access to the Camera.

ENGLISH

Setup

Connect the Camera to the power adapter, then plug into an suitable electrical outlet and make sure the power switch is in the ON position. The Camera must be within range of the Wi-Fi® router with which you want to connect. Make sure the password of the router is available for entering during the in-app setup process.

Status of LED Indication:

- Pair / Setup state:		LED is red and blue and slowly flashing
-	Unconnected state:	LED is red and slowly flashing
-	Connected state:	LED is blue and always on

- Ready for connection state: LED is blue and slow flashing

Note: You can only setup via a compatible smartphone or tablet and not via a PC.

Wi-Fi Internet Viewing	21

5.3User Account and Camera Setup on Android™ Devices

What you need

• MBP854CONNECT camera

• The power adapter for the Camera

• Device with Android™ system version 4.2 or above

5.3.1 Power ON and Connect the Camera

• Connect the power adapter to an electrical outlet and insert the plug into the micro USB socket on the back of the Camera.

• Make sure that the ON/OFF switch is in the ON position.

• The Camera’s Red LED flashes after the Camera has finished booting. When you hear two ‘beeps’ this means the Camera is ready to setup.

5.3.2 Download the Hubble App

•Go to the Google Play™ Store to search “Hubble for Motorola Monitors”.

•Download the Hubble for Motorola Monitors App from the Google Play™ Store and install it into your Android™ device.

22	Wi-Fi Internet Viewing