User’s Guide
Digital Video Baby Monitor With Wi-Fi® Internet Viewing
Models: MBP853CONNECT, MBP853CONNECT-2,
MBP853CONNECT-3, MBP853CONNECT-4
The features described in this User’s Guide are subject to modifications without prior notice.
Welcome...
to your new Motorola Digital Video Baby Monitor!
Thank you for purchasing your new Motorola Digital Video Baby Monitor. Now you can see and hear your baby sleeping in another room or you can monitor your older children in their playroom.
Please retain your original dated sales receipt for your records.
For warranty service of your Motorola product, you will need to provide a copy of your dated sales receipt to confirm warranty status. Registration is not required for warranty coverage.
For product related questions, please call:
+49 (0) 1805 938 802 in Europe Email: motorola-mbp@tdm.de
This User's Guide provides you with all the information you need to get the most from your product.
Before you can use the Baby Monitor, we recommend you insert and fully charge the battery in the Parent Unit, so that it continues to work if you disconnect it from the power supply to carry it to another location. Please read the Safety Instructions on page 8 before you install the units.
Got everything?
•1 x Parent Unit
•1 x Baby Unit (Camera)
•1 x Power adapter for the Parent Unit
•1 x Power adapter(s) for the Baby Unit(s)
•1 x Rechargeable Ni-MH battery pack
In multi-camera packs, you will find one or more additional camera units with power adapter units and battery packs.
Overview of the Parent Unit |
|
||||
10 |
11 |
12 |
1 |
14 |
POWER |
|
|
||||
|
|
|
|
15 |
|
2 |
|
|
6 |
|
19 |
|
|
|
|
|
|
3 |
|
|
7 |
|
18 |
|
|
|
|
|
|
4 |
|
|
8 |
16 |
20 |
|
|
|
|
|
|
5 |
|
|
9 |
|
|
13 |
|
|
|
17 |
|
|
|
|
|
|
1. |
Display (LCD screen) |
10. |
Power Adapter / Battery LED |
2. |
Up Key + |
|
BLUE when mains adapter power on. |
|
Normal Mode: Tilt Up |
|
RED when battery low. |
|
Menu Mode: Up |
11. |
Unit ON/OFF LED (Green) |
3. |
Down Key - |
12. |
Audio Level LED (Green, Orange, |
|
Normal Mode: Tilt Down |
|
Red, Red) |
|
Menu Mode: Down |
13. |
Microphone |
4. |
Left Key < |
14. |
Power Key P |
|
Normal Mode: Pan Left |
|
Press and Hold to turn the unit ON/ |
|
Menu Mode: Left |
|
OFF |
5. |
Right Key > |
15. |
Antenna |
|
Normal Mode: Pan Right |
|
Lift the antenna for optimal |
|
Menu Mode: Right |
|
reception |
6. |
Menu Key M |
16. |
Battery cover |
|
Press to open the Menu options |
17. |
Stand |
7. |
OK Key O |
18. |
Speaker |
8. |
Video ON/OFF Key V |
19. |
USB power adapter socket |
|
Press to turn OFF the LCD display |
20. |
AV out / Audio out |
|
Press again to turn ON the LCD |
|
|
|
display |
|
|
9.Talk Key T
Press and hold to speak to your baby
Parent Unit menu icons
|
Signal Level (4 Levels) |
|
|
|
Night Vision Mode (Screen changes to Black/White) |
|
|
|
Talk Mode |
|
|
|
Battery Level Control (4 Levels) |
|
|
|
Pan Left |
|
|
|
Pan Right |
|
|
|
Tilt Up |
|
|
|
Tilt Down |
|
|
|
Volume Level Control (8 Levels) |
|
|
|
Zoom Level Control (1X, 2X) |
|
|
|
Brightness Level Control (8 Levels) |
|
|
|
Lullaby Control (5 Song Selections) |
|
|
|
Alarm Setting (6h, 4h, 2h, Off) |
|
|
|
Temperature Reading (HH ºC / ºF or LL ºC / ºF) |
|
Icon & readings turn RED > 29ºC / 84ºF, and reading display |
|
(HH ºC / ºF > 36ºC / 97 ºF) |
|
Icon & readings turn RED < 14ºC / 57ºF, and reading display |
|
(LL ºC / ºF < 1ºC / 34 ºF) |
|
Camera Control (scan, view, add, delete) |
|
|
|
View multiple cameras on screen (Picture in Picture). Available when you |
|
have more than 1 Baby Unit (Camera). |
|
|
V |
Set Video On Timer (5 min, 30 min, 60 min) |
|
|
Overview of Your Baby Unit |
|
|
|
|
|
1 |
|
|
|
|
2 |
|
|
8 |
|
3 |
|
|
|
|
4 |
|
|
|
|
5 |
|
|
|
|
6 |
|
|
9 |
|
|
5V 1.5A |
10 |
|
|
7 |
|
|
11 |
1. |
Light Sensor (for night mode detection) |
7. |
Speaker |
|
2. |
Camera Lens |
8. |
Antenna |
|
3. |
Infrared LEDs (for night vision) |
9. |
Micro USB socket |
|
4. |
Power / Status indicator |
10. ON/OFF Switch |
|
|
5. |
Microphone |
11. Temperature Sensor |
|
|
6. |
PAIR Button |
|
|
|
Important guidelines for installing your Baby Monitor
•To use your Video Monitor Baby and Parent Units together, you must be able to establish a radio link between them, and the range will be affected by environmental conditions.
•Any large metal object, like a refrigerator, a mirror, a filing cabinet, metallic doors or reinforced concrete between the Baby and Parent Unit may block the radio signal.
•The signal strength may also be reduced by other solid structures, like walls, or by radio or electrical equipment, such as TVs, computers, cordless or mobile phones, fluorescent lights or dimmer switches.
•Use of other 2.4 GHz products, such as wireless networks (Wi-Fi® routers), Bluetooth® systems, or microwave ovens, may cause interference with this product, so keep the Baby Monitor away at least 1m from these types of products, or turn them off if they appear to be causing interference.
•If the signal is weak, try raising the Parent Unit Antenna, moving the Parent and/or the Baby Unit to different positions in the room(s).
Table of contents
1. |
Safety Instructions..................................................................................... |
8 |
||
2. |
Getting Started........................................................................................ |
11 |
||
|
2.1 |
Baby Unit Power Supply ......................................................................... |
11 |
|
|
2.2 |
Parent Unit Battery Installation.................................................................. |
11 |
|
|
2.3 |
Parent Unit Power Supply ......................................................................... |
12 |
|
|
2.4 |
Registration (Pairing) ................................................................................ |
13 |
|
|
2.5 |
View Video Through TV............................................................................ |
13 |
|
3. Using the Baby Monitor........................................................................... |
15 |
|||
|
3.1 |
Setting up .................................................................................................. |
15 |
|
|
3.2 |
Pan and Tilt ................................................................................................ |
15 |
|
|
3.3 |
Night Vision Mode .................................................................................... |
15 |
|
|
3.4 |
Talk Mode.................................................................................................. |
15 |
|
|
3.5 |
Video ON/OFF ......................................................................................... |
15 |
|
|
3.6 |
Temperature Display (HH °C / °F or LL °C / °F)...................................... |
15 |
|
4. Parent Unit Menu Options ...................................................................... |
16 |
|||
|
4.1 |
Volume |
...................................................................................................... |
16 |
|
4.2 |
Brightness.................................................................................................. |
16 |
|
|
4.3 |
Lullaby ....................................................................................................... |
|
16 |
|
4.4 |
Zoom ......................................................................................................... |
|
16 |
|
4.5 |
Alarm ......................................................................................................... |
|
16 |
|
4.6 |
Camera ........................................................................................Control |
17 |
|
|
|
4.6.1 .................................................................. |
Add (pair) a camera |
17 |
|
|
4.6.2 ........................................................................... |
View a camera |
17 |
|
|
4.6.3 .................. |
View multi - cameras on screen (Picture in Picture) |
17 |
|
|
4.6.4 ........................................................................ |
Delete a camera |
18 |
|
|
4.6.5 .............................................................................. |
Scan camera |
18 |
|
4.7 |
Temperature ............................................................................................. |
19 |
|
|
4.8 |
Power Saving ..................................................................................mode |
19 |
|
5. |
Wi-Fi Internet ............................................................................Viewing |
20 |
||
|
5.1 |
System ...............................................................................Requirements |
20 |
|
|
5.2 |
Getting .....................................................started - Connecting Devices |
21 |
|
|
5.3 |
User Account .......................and Camera Setup on Android™ Devices |
22 |
|
|
|
5.3.1 ...................................... |
Power ON and Connect the Camera |
22 |
|
|
5.3.2 ....................................................... |
Download the Hubble App |
22 |
|
|
5.3.3 ............................. |
Run the Hubble App on Android™ device |
23 |
|
|
5.3.4 ................................................... |
Add Camera to your account |
24 |
6 |
Table of contents |
|
|
5.4 User Account and Camera Setup: |
|
|
Working with iPhone®/iPad®................................................................... |
28 |
|
5.4.1 |
Power ON and Connect the Camera ...................................... |
28 |
5.4.2 |
Download the Hubble App ....................................................... |
28 |
5.4.3 |
Run the Hubble App on your iPhone®/iPad® ......................... |
29 |
5.4.4 |
Add the Camera to your account ............................................. |
30 |
5.5Camera Functions:
Working with devices for Android™ ....................................................... |
34 |
|
5.5.1 |
Connecting the Camera to Power ........................................... |
34 |
5.5.2 |
Add more cameras .................................................................... |
34 |
5.5.3 |
Remove a Camera .................................................................... |
35 |
5.5.4 |
Change your Account Information .......................................... |
36 |
5.5.5 |
Camera settings ........................................................................ |
37 |
5.5.6 |
General Settings ........................................................................ |
38 |
5.5.7 |
Features of the Hubble App ..................................................... |
39 |
5.6Camera Functions:
|
Working with devices for iPhone®/iPad® ............................................... |
43 |
|
|
5.6.1 |
Add more cameras .................................................................... |
43 |
|
5.6.2 |
Remove a Camera .................................................................... |
44 |
|
5.6.3 |
Change your Account Information .......................................... |
45 |
|
5.6.4 |
Camera settings ........................................................................ |
46 |
|
5.6.5 |
General settings ........................................................................ |
47 |
|
5.6.6 |
Hubble App Settings ................................................................. |
48 |
|
5.6.7 |
Features of the Hubble App ..................................................... |
49 |
|
5.7 Camera Functions: |
|
|
|
Working with PC/Notebook..................................................................... |
52 |
|
|
5.8 Procedure for resetting the Camera ........................................................ |
52 |
|
6. |
Disposal of The Device (environment) ................................................... |
53 |
|
7. |
Cleaning .................................................................................................. |
|
54 |
8. |
Help.......................................................................................................... |
|
55 |
9. |
General Information ................................................................................ |
63 |
ENGLISH
Table of contents |
7 |
|
|
WARNING:
Strangulation Hazard: Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3ft (1m) away). Never use extension cords with AC Adapters. Only use the AC Adapters provided.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
8 |
|
|
|
Safety Instructions |
|
|
|
|
|
Baby Unit SET UP & USE:
●Choose a location for the Baby Unit that will provide the best view of your baby in their cot.
●Place the Baby Unit on a flat surface, such as a dresser, desk, or shelf or mount the Unit to a wall securely using the keyhole slots on the underside of the stand.
●NEVER place the Baby Unit or cords inside your child's cot.
●Do not place the Baby Unit or cords in the cot or within reach of the baby (the unit and cords should be more than 1 metre away).
ENGLISH
WARNING
This digital video Baby Monitor is compliant with all relevant standards regarding electromagnetic fields and is, when handled as described in the User's Guide, safe to use. Therefore, always read the instructions in this User's Guide carefully before using the device.
•Adult assembly is required. Keep small parts away from children when assembling.
•This product is not a toy. Do not allow children to play with it.
•This Baby Monitor is not a substitute for responsible adult supervision.
•Keep this User’s Guide for future reference.
•Do not place the Baby Unit or cords in the cot or within reach of the baby (the unit and cords should be more than 1 metre away)
•Keep the cords out of reach of children.
•Do not cover the Baby Monitor with a towel or blanket.
•Never use extension cords with power adapters. Only use the power adapters provided.
•Test this monitor and all its functions so that you are familiar with it prior to actual use.
•Do not use the Baby Monitor near water.
Safety Instructions |
9 |
|
|
•Do not place the Baby Monitor near a heat source.
•Only use the chargers and power adapters provided. Do not use other chargers or power adapters as this may damage the device and battery pack.
•Only insert approved battery pack.
•Do not touch the plug contacts with sharp or metal objects.
CAUTION
Risk of explosion if battery is replaced by an unapproved battery type. Dispose of used batteries according to their instructions.
The Unit shall be setup and used such that parts of the user’s body other than the hands are maintained at a distance of approximately 20 cm (8 inches) or more.
10 |
Safety Instructions |
|
|
Power adapter plug
Switch to turn ON |
ON OFF |
|
the camera |
||
|
ENGLISH
1.Connect the small plug of the power adapter to the Baby Unit (camera) and the other end to a suitable mains power socket.
NOTE
Only use the enclosed power adapter (5V DC / 1500mA).
2.Slide the ON/OFF switch to the ON position. The power LED will light up in blue.
3.Slide the ON/OFF switch to the OFF position to turn the Baby Unit off.
Red
Black
1.Insert the wire tab of the rechargeable battery pack into the contact slot as shown above and fit the battery pack into the compartment.
Small cross head or
Flat end screw driver
|
|
|
|
|
|
Getting Started |
11 |
|
|
|
|
2.Replace the battery cover over the compartment and gently tighten the screw in a clockwise direction using a Small cross head or Flat end screw drivers.
IMPORTANT
Installing the rechargeable battery pack and charging it fully before use is recommended. This will allow the unit to operate on battery in the event of a power failure.
1.Connect the small plug of the power adapter to the Parent Unit and the other end to a suitable mains power socket. Only use the enclosed power adapter (5V DC / 600mA) with micro USB plug.
2.Press and hold the PPOWER ON/OFF button for 2 seconds to turn ON the Parent Unit.
3.Once the Baby and Parent Units are switched on, the display on the Parent Unit will show the video captured by the Baby Unit.
4.If there is no connection or you are out of range, the video display will be
replace by a symbol and the unit will beep every 5 seconds. Move the Parent Unit closer to the Baby Unit until the link is re-established.
5.Press and hold the PPOWER ON/OFF button, until the progress bar finishes scrolling, to turn OFF the Parent Unit.
NOTE
The battery icon turns RED to indicate that the battery is low, and the parent unit will beep every 15 seconds. The battery needs to be recharged; it will take 12 hours to charge fully.
12 |
Getting Started |
|
|
When charging |
ENGLISH |
|
|
at the top left corner will light up, indicating that the adapter is plugged in. |
|
1. |
During power OFF, and the adapter is plugged in, an adapter logo will display |
|
|
on-screen and then a flashing battery logo will display for 45 sec. The Blue LED |
|
2. |
Whilst the power is ON, and the adapter is plugged in, the battery icon at the |
|
|
top right corner of the screen will show that the battery is charging. The Blue |
|
|
|
|
|
LED at the top left corner will light up to indicate that the adapter is plugged in. |
|
The Baby monitor is pre-registered to your Parent Unit. You do not need to register it again unless the Baby Unit loses its link with the Parent Unit.
To re-register your Baby Unit, or register a new Baby Unit, follow the procedure below:
1.Press the M button of the Parent Unit and the menu bar will pop up.
2. |
Press the |
|
|
|
LEFT button or |
RIGHT button until |
is highlighted, and |
|||
|
the del / |
|
/ |
|
/ scan menu will pop up. |
|
||||
|
add |
view |
|
|||||||
3. |
Press the |
|
|
|
UP button or |
DOWN button to select add , and press the |
||||
4. |
Obutton to confirm. |
|
|
|||||||
*1 / |
2 / |
3 |
/ 4 will pop up, press the UP button or DOWN button |
|||||||
|
cam |
cam |
cam |
|
cam |
|
|
to select the desired CAM and press the O button to start searching for a camera unit. The green audio level LED will flash rapidly while searching.
5.Press the O button to confirm.
6.Press and hold the PAIR button underneath the Baby Unit until the Parent Unit finds the camera, beeps and the video from the camera appears.
NOTE
If a particular Baby Unit was registered previously, registering this current Baby Unit again will overwrite the old registration.
Connect a suitable AV cable into the AV OUT socket on the side of the Parent Unit and into the AV input of the TV. Scroll to select V:< on the Parent Unit and press Obutton to confirm, the display screen goes off. Scroll through the AV inputs on the TV menu until the Baby monitor picture is visible. AV cable is an optional accessory, which is to be purchased separately.
Getting Started |
13 |
|
|
NOTE
The Monitor's power button must be turned ON and CAM pre-selected before connecting the AV cable. Once the AV cable is connected, the Monitor's controls cannot be activated.
You can hear also your baby in mono mode by connecting the 3.5mm plug wired headset to the AV OUT socket.
14 |
Getting Started |
|
|
•Place the Baby Unit in a convenient location (e.g. on a table) and point the camera lens towards the area you want to monitor.
•Adjust the angle of the Baby Unit's head by rotating the camera up, down, left and right until you are satisfied with the image in the Parent Unit.
NOTE
Do not place the Baby Unit within the baby's reach! If there is interference with the picture or sound, try moving the units to different locations, and ensure they are not close to other electrical equipment.
The camera can be remotely controlled from the Parent Unit.
1. Press the UP button or DOWN button to tilt up or down.
2.Press the LEFT button or RIGHT button to pan left or right.
The Baby Unit has 8 high-intensity infrared LEDs for picking up clear images in the dark. When the built-in photo sensor on the top of the unit detects a low level of ambient light, the LEDs will automatically activate and the screen on the Parent Unit will display in black and white. The icon will be displayed at the top of the screen.
Press and hold theTTALK button on the Parent Unit to talk to your baby throughthe Baby Unit’s loudspeaker. The T icon will be displayed at the top of the LCD screen.
Press VVIDEO ON/OFF key to turn the LCD display on or off, whilst still leaving the audio monitor on.
The temperature reading from the temperature sensor at the back of the Baby Unit will be displayed at the top of the LCD screen. The readings will turn RED if the temperature goes above 29°C / 84°F or below 14°C / 57°F. The reading will change to HH °C / °F if the temperature goes above 36°C / 97°F. The reading will change to LL °C / °F if the temperature goes below 1°C / 34°F.
ENGLISH
Using the Baby Monitor |
15 |
|
|
4.1 |
Volume |
|
|
|
1. |
Press the Mbutton and the menu bar will pop up. |
|
||
2. |
Press the |
LEFT button or |
RIGHT button until |
is highlighted. |
3. |
Press the |
UP button or |
DOWN button to select the desired volume |
|
|
level from level 0 ~ 8. (The default volume level setting is level 4.) |
4.2 |
Brightness |
|
|
|
1. |
Press the Mbutton and the menu bar will pop up. |
|
||
2. |
Press the |
LEFT button or |
RIGHT button until |
is highlighted. |
3. |
Press the |
UP button or |
DOWN button to select the desired brightness |
|
|
level from level 1 ~ 8. (The default brightness level setting is level 5.) |
4.3 |
Lullaby |
|
|
|
1. |
Press the Mbutton and the menu bar will pop up. |
|
||
2. |
Press the |
LEFT button or |
RIGHT button until |
is highlighted. |
3. |
Press the |
UP button or |
DOWN button to select the desired song |
|
|
from the 5 lullabies available, or the cycle option to play all 5 songs in turn. If |
|||
|
an individual song is selected it will only play once. (The default setting is |
|||
|
lullaby OFF) |
|
|
|
4.4 |
Zoom |
|
|
|
1. |
Press the Mbutton and the menu bar will pop up. |
|
||
2. |
Press the |
LEFT button or |
RIGHT button until |
is highlighted. |
3. |
Press the |
UP button or |
DOWN button to select the 1X or 2X Zoom. |
|
|
(The default setting is 1X.) |
|
|
|
4.5 |
Alarm |
|
|
|
1.Press the Mbutton and the menu bar will pop up.
2.Press the LEFT button or RIGHT button until is highlighted.
3.Press the UP button or DOWN button to select the alarm time (6h, 4h, 2h). (The default setting is Alarm OFF.)
4.If an alarm time is selected, the Parent Unit will beep for about 45 seconds after every 6, 4 or 2 hour period.
16 |
Parent Unit Menu Options |
|
|
1.Press the Mbutton and the menu bar will pop up.
2.Press the LEFT button or RIGHT button until is highlighted, and
the del / add / view / scan menu will pop up.
3.Press the UP button or DOWN button to select add , and press the OK button to confirm.
4. |
*1 |
/ |
2 |
/ |
3 |
/ |
4 |
will pop up, press the UP button or DOWN button |
|
cam |
|
cam |
|
cam |
|
cam |
|
to select the desired CAM, and press the OK button to start searching for a camera unit. The green audio level LED will flash rapidly while searching.
5.Press and hold the PAIR button on the underside of the Baby Unit until the Parent Unit finds the camera, beeps and the picture from the camera appears.
NOTE
A camera can only be registered to one Parent Unit at any one time.
1.Press the Mbutton and the menu bar will pop up.
2.Press the LEFT button or RIGHT button until is highlighted and the del / add / view / scan menu pops up.
3.Press the UP button or DOWN button to select view , and press the OK button to confirm.
4. |
*1 |
/ |
2 |
/ |
3 |
/ |
4 |
will pop up, press the UP button or DOWN button |
|
cam |
|
cam |
|
cam |
|
cam |
|
to select the desired camera, and press the OK button to view the picture from that camera.
TIP
Quick Method to View Cameras instead of entering into the menu bar.
Directly press OK repeatedly to select |
cam |
, |
cam |
, |
cam |
, |
cam |
, scan . |
*1 |
2 |
3 |
4 |
4.6.3View multi-cameras on screen (Picture in Picture)
This function is only available when you have more than 1 Baby Unit (Camera). When the Picture in Picture function is On, you can view multiple cameras on the screen.
ENGLISH
Parent Unit Menu Options |
17 |
|
|
1.Press the Mbutton and the menu bar will pop up.
2.Press the LEFT button or RIGHT button until is highlighted.
3.Press the UP button or DOWN button to select Picture in Picture On/Off.
4.When the Picture in Picture function is On, you can press the LEFT button/ RIGHT button/ UP button / DOWN button to switch between cameras.
1.Press the Mbutton and the menu bar will pop up.
2.Press the LEFT button or RIGHT button until is highlighted, and the del / add / view / scan menu will pop up.
3.Press the UP button or DOWN button to select del , and press the OK button to confirm.
4. |
*1 |
/ |
2 |
/ |
3 |
/ |
4 |
will pop up, press the UP button or DOWN button |
|
cam |
|
cam |
|
cam |
|
cam |
|
to select the desired CAM, and press the OK button to delete that registration.
Note:
You are not allowed to delete the camera if there is only one registered camera in the system.
This function is only available when you have more than 1 Baby Unit (Camera).
1.Press the Mbutton and the menu bar will pop up.
2.Press the LEFT button or RIGHT button until is highlighted, and the del / add / view / scan menu will pop up.
3.Press the UP button or DOWN button to select scan , and press the OK button to confirm.
4.The screen will then display images from different registered cameras in a
loop of |
*1 |
/ |
2 |
/ |
3 |
/ |
4 |
, changing about every 12 seconds. |
|
cam |
|
cam |
|
cam |
|
cam |
|
TIP
Quick Method to View Cameras instead of entering into the menu bar.
Directly press OK repeatedly to select |
cam |
, |
cam |
, |
cam |
, |
cam |
, scan . |
*1 |
2 |
3 |
4 |
18 |
Parent Unit Menu Options |
|
|
1.Press the Mbutton and the menu bar will pop up.
2.Press the LEFT button or RIGHT button until is highlighted.
3.Press the UP button or DOWN button to select °C or °F.
1.Press the Mbutton and the menu bar will pop up.
2.Press the LEFT button or RIGHT button until Vis highlighted.
3.Press the UP button or DOWN button to select auto video off after 5 mins, 30 mins or 60 mins if not in charging.
ENGLISH
Parent Unit Menu Options |
19 |
|
|
Web Portal
•Windows® 7
•Mac OS® 10.7
•Chrome™ 24
•Internet Explorer® 9
•Safari® 6
•Java™ 7
•Firefox® 18.0
•Adobe® Flash® Player 15.0
Android™ System
• Version 4.2 or above
iPhone®/iPad® iOS
• Version 7.0 or above
Wi-Fi® requirements:
•At least 0.6 Mbps upload bandwidth per camera. Test your Internet speed at: http://www.speedtest.net/
20 |
Wi-Fi Internet Viewing |
|
|
How does it work?
View your Camera from any compatible device remotely
When a user tries to access the Camera, our secure server authenticates the user’s identity and permits access to the Camera.
Setup
Connect the Camera to the power adapter, then plug into a suitable mains power socket and make sure the power switch is in the ON position. The Camera must be within range of the Wi-Fi® router with which you want to connect. Make sure the password of the router is available for entering during the in-app setup process.
ENGLISH
Status of LED Indication:
- Pair / Setup state: |
LED is red and blue and flashing slowly |
|
- |
Unconnected state: |
LED is red and flashing slowly |
- |
Connected state: |
LED is blue and always on |
- Ready for connection state: LED is red and flashing slowly
Note: You can only setup via a compatible smartphone or tablet and not via a PC.
Wi-Fi Internet Viewing |
21 |
|
|
• MBP853CONNECT camera
• The power adapter for the Camera
• Device with Android™ system version 4.2 or above
• Connect the power adapter to an mains power socket and insert the plug into the micro USB socket on the back of the Camera.
• Make sure that the ON/OFF switch is in the ON position.
• The Camera’s Red LED flashes after the Camera has finished booting. When you hear two ‘beeps’ this means the Camera is ready to setup.
•Go to the Google Play™ Store to search “Hubble for Motorola Monitors”.
•Download the Hubble for Motorola Monitors App from the Google Play™ Store and install it on your Android™ device.
22 |
Wi-Fi Internet Viewing |
|
|
•Ensure your Android™ device is connected to your Wi-Fi® router.
•Run the Hubble App and key in your Hubble App account information, read through the Terms of Service then select “I agree to the Terms of Use” before you tap on Create. (Picture A1)
Note: If you have a Hubble account, please select Already have a Account? to go to the next step.
A1
Android™ ENGLISH
Wi-Fi Internet Viewing |
23 |
|
|
•Create a new account and Login.
•Tap on Add Camera. (Picture A2)
•Tap on Continue. (Picture A3)
|
|
|
A2 |
A3 |
• The setup instructions will appear on the following screen. (Picture A4)
A4
24 |
Wi-Fi Internet Viewing |
|
|
• Press and hold the PAIR button for 3 seconds at the side of the Camera, you |
ENGLISH |
|||
• The App will automatically search for and connect to your Camera as shown |
||||
will then hear a beep tone and a voice saying "Ready for pairing" from the |
|
|||
Camera Unit. Tap on Search for Camera. |
|
|||
in the pictures below (Pictures A5, A6) and the blue/red coloured LED on the |
|
|||
Camera will flash. |
|
|||
Android™ |
||||
|
|
|
||
|
|
|
||
|
|
|
|
A5 |
A6 |
Wi-Fi Internet Viewing |
25 |
|
|
•Select your Wi-Fi® Network and tap Continue, enter your password then tap on Connect. (Pictures A7, A8)
|
|
A7 |
A8 |
•It will take a few minutes for the Camera to connect to the Wi-Fi® network before showing the connection status (Pictures A9, A10). If connection fails, please tap on the Retry button and repeat the steps starting from 5.3.4.
|
|
|
A9 |
|
A10 |
26 |
Wi-Fi Internet Viewing |
|
|
• |
Tap on Watch Live Camera to view the Camera video, the Camera's Blue |
ENGLISH |
|
LED will flash. (Picture A11) |
|
|
|
|
• |
Tap on the Hubble logo and go back to the Camera list. (Picture A12) |
|
|
|
|
Android™
A11 |
A12 |
Wi-Fi Internet Viewing |
27 |
|
|
• MBP853CONNECT camera
• The power adapter for the Camera
• iPhone® / iPad® with iOS 7.0 version or up
• Connect the power adapter to an mains power socket and insert the plug into the micro USB socket at the back of the Camera.
• Make sure that the ON/OFF switch is in the ON position.
• The Camera's red LED flashes after the Camera has finished booting. When you hear two beeps, this means the Camera is ready for setup.
•Go to the App Store to search for “Hubble for Motorola Monitors”.
•Download the Hubble for Motorola Monitors App and install it on your iPhone®/iPad®.
28 |
Wi-Fi Internet Viewing |
|
|
5.4.3Run the Hubble App on your iPhone®/iPad®
•Ensure your iPhone®/iPad® is connected to your Wi-Fi® Router.
•Run the Hubble App and key in your account information, read through the Terms of Service then select “I agree to the Terms of Service” before you tap on Create. (Picture i1)
Note: If you have a Hubble account, please select Already have a Account? to go to the next step.
i1
iOS ENGLISH
Wi-Fi Internet Viewing |
29 |
|
|
•Create a new account and Login.
•Tap on Add Camera. (Picture i2)
•Tap on “MBP853CONNECT”. (Picture i3)
|
|
|
i2 |
|
i3 |
•Follow the instruction on screen to turn on the Bluetooth™ function of your iPhone/iPad.
i4
30 |
Wi-Fi Internet Viewing |
|
|