MOTOROLA MC10H124FNR2, MC10H124M, MC10H124MEL, MC10H124ML1, MC10H124ML2 Datasheet
...
MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Quad TTL-to-MECL Translator
With TTL Strobe Input
The MC10H124 is a quad translator for interfacing data and control signals between a saturated logic section and the MECL section of digital systems. The 10H part is a functional/pinout duplication of the standard MECL 10K family part, with 100% improvement in propagation delay, and no increase in power±supply current.
•Propagation Delay, 1.5 ns Typical
•Improved Noise Margin 150 mV (Over Operating Voltage and Temperature Range)
•Voltage Compensated
•MECL 10K±Compatible
MAXIMUM RATINGS
Characteristic |
|
|
|
|
Symbol |
|
|
Rating |
|
|
Unit |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Power Supply (VCC = 5.0 V) |
|
|
|
|
|
VEE |
|
|
±8.0 to 0 |
|
|
Vdc |
|||
Power Supply (VEE = ±5.2 V) |
|
|
|
|
VCC |
|
|
0 to +7.0 |
|
|
Vdc |
||||
Input Voltage (VCC = 5.0 V) TTL |
|
|
|
|
VI |
|
|
0 to VCC |
|
|
Vdc |
||||
Output Current Ð Continuous |
|
|
|
|
|
Iout |
|
|
50 |
|
|
|
mA |
||
Ð Surge |
|
|
|
|
|
|
|
|
100 |
|
|
|
|
|
|
Operating Temperature Range |
|
|
|
|
TA |
|
|
0 to +75 |
|
|
|
°C |
|||
Storage Temperature Range Ð Plastic |
|
|
|
|
Tstg |
|
±55 to +150 |
|
|
|
°C |
||||
|
|
Ð Ceramic |
|
|
|
|
|
|
±55 to +165 |
|
|
|
|
||
ELECTRICAL CHARACTERISTICS (VEE = ±5.2 V ±5%, VCC = 5.0 V ± 5.0%) |
|||||||||||||||
|
|
|
0° |
|
|
25° |
|
75° |
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
Characteristic |
|
Symbol |
Min |
|
Max |
Min |
Max |
Min |
|
Max |
|
Unit |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
Negative Power |
|
IE |
Ð |
|
72 |
Ð |
66 |
Ð |
|
72 |
|
mA |
|||
Supply Drain |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Current |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
Positive Power Supply |
|
ICCH |
Ð |
|
16 |
Ð |
16 |
Ð |
|
18 |
|
mA |
|||
Drain Current |
|
ICCL |
Ð |
|
25 |
Ð |
25 |
Ð |
|
25 |
|
mA |
|||
|
|
|
|
|
|||||||||||
Reverse Current |
|
IR |
|
|
|
|
|
|
|
|
|
|
|
|
μA |
Pin 6 |
|
|
Ð |
|
200 |
Ð |
200 |
Ð |
|
200 |
|
|
|||
Pin 7 |
|
|
Ð |
|
50 |
Ð |
50 |
Ð |
|
50 |
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Forward Current |
|
IF |
|
|
|
|
|
|
|
|
|
|
|
|
mA |
Pin 6 |
|
|
Ð |
|
±12.8 |
Ð |
±12.8 |
Ð |
|
±12.8 |
|
|
|||
Pin 7 |
|
|
Ð |
|
±3.2 |
Ð |
±3.2 |
Ð |
|
±3.2 |
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Input Breakdown |
|
V(BR)in |
5.5 |
|
Ð |
|
5.5 |
Ð |
5.5 |
|
Ð |
|
|
Vdc |
|
Voltage |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Input Clamp Voltage |
|
VI |
Ð |
|
±1.5 |
Ð |
±1.5 |
Ð |
|
±1.5 |
|
Vdc |
|||
High Output Voltage |
|
VOH |
±1.02 |
|
±0.84 |
±0.98 |
±0.81 |
±0.92 |
|
±0.735 |
|
Vdc |
|||
Low Output Voltage |
|
VOL |
±1.95 |
|
±1.63 |
±1.95 |
±1.63 |
±1.95 |
|
±1.60 |
|
Vdc |
|||
High Input Voltage |
|
VIH |
2.0 |
|
Ð |
|
2.0 |
Ð |
2.0 |
|
Ð |
|
|
Vdc |
|
Low Input Voltage |
|
VIL |
Ð |
|
0.8 |
Ð |
0.8 |
Ð |
|
0.8 |
|
Vdc |
|||
NOTE:
Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 Ifpm is maintained. Outputs are terminated through a 50±ohm resistor to ±2.0 volts.
MC10H124
|
L SUFFIX |
|
CERAMIC PACKAGE |
|
CASE 620±10 |
|
P SUFFIX |
|
PLASTIC PACKAGE |
|
CASE 648±08 |
|
FN SUFFIX |
|
PLCC |
|
CASE 775±02 |
|
LOGIC DIAGRAM |
5 |
4 |
6 |
2 |
7 |
3 |
|
1 |
10 |
12 |
|
15 |
11 |
13 |
|
14 |
GND = PIN 16
VCC ( +5.0 VDC) = PIN 9
VEE ( ±5.2 VDC) = PIN 8
DIP
PIN ASSIGNMENT
|
BOUT |
|
1 |
|
16 |
|
|
GND |
|
|
|
|
|
|
|||||
|
AOUT |
|
2 |
|
15 |
|
|
COUT |
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
DOUT |
|
BOUT |
|
3 |
|
14 |
|
|
||
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
AOUT |
|
4 |
|
13 |
|
|
DOUT |
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
AIN |
|
5 |
|
12 |
|
|
COUT |
|
|
|
|
|
|
|||||
COMMON |
|
6 |
|
11 |
|
|
DIN |
||
|
|
|
|
||||||
STROBE |
|
|
|
|
|||||
|
|
|
|
|
|
CIN |
|||
|
BIN |
|
7 |
|
10 |
|
|
||
|
VEE |
|
8 |
|
9 |
|
|
VCC |
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
Pin assignment is for Dual±in±Line Package. For PLCC pin assignment, see the Pin Conversion Tables on page 6±36 of the Motorola MECL Data Book (DL122/D).
9/96
Motorola, Inc. 1996 |
2±5 |
REV 6 |
MC10H124
ELECTRICAL CHARACTERISTICS (VEE = ±5.2 V ±5%, VCC = 5.0 V ± 5.0%)
|
|
|
0° |
|
25° |
|
75° |
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
Characteristic |
Symbol |
Min |
|
Max |
Min |
|
Max |
Min |
|
Max |
Unit |
|
|
|
|
|
|
|
|
|
|
|
|
AC PARAMETERS |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
Propagation Delay |
tpd |
0.55 |
|
2.25 |
0.55 |
|
2.4 |
0.85 |
|
2.95 |
ns |
Rise Time |
tr |
0.5 |
|
1.5 |
0.5 |
|
1.6 |
0.5 |
|
1.7 |
ns |
Fall Time |
tf |
0.5 |
|
1.5 |
0.5 |
|
1.6 |
0.5 |
|
1.7 |
ns |
APPLICATIONS INFORMATION
The MC10H124 has TTL±compatible inputs and MECL complementary open±emitter outputs that allow use as an inverting/non±inverting translator or as a differential line driver. When the common strobe input is at the low±logic level, it forces all true outputs to a MECL low±logic state and all inverting outputs to a MECL high±logic state.
An advantage of this device is that TTL±level information can be transmitted differentially, via balanced twisted pair lines, to MECL equipment, where the signal can be received by the MC10H115 or MC10H116 differential line receivers. The power supply requirements are ground, +5.0 volts, and ±5.2 volts.
MOTOROLA |
2±6 |
MECL Data |
|
|
DL122 Ð Rev 6 |
Loading...