Motorola MC10H136P, MC10H136FN, MC10H136FNR2, MC10H136L Datasheet

MOTOROLA

SEMICONDUCTOR TECHNICAL DATA

	Universal Hexadecimal	MC10H136
	Counter

The MC10H136 is a high speed synchronous hexadecimal counter. This 10H part is a functional/pinout duplication of the standard MECL 10K family part, with 100% improvement in counting frequency and no increase in power-supply current.

•	Counting Frequency, 250 MHz Minimum	•	Voltage Compensated
•	Power Dissipation, 625 mW Typical	•	MECL 10K-Compatible

•Improved Noise Margin 150 mV

(Over Operating Voltage and Temperature Range)

L SUFFIX

CERAMIC PACKAGE

CASE 620±10

P SUFFIX

PLASTIC PACKAGE

CASE 648±08

FN SUFFIX

PLCC

CASE 775±02

MAXIMUM RATINGS

Characteristic	Symbol	Rating	Unit
Power Supply (VCC = 0)	VEE	±8.0 to 0	Vdc
Input Voltage (VCC = 0)	VI	0 to VEE	Vdc
Output Current Ð Continuous	Iout	50	mA
Ð Surge		100
Operating Temperature Range	TA	0 to +75	°C
Storage Temperature Range Ð Plastic	Tstg	±55 to +150	°C
Ð Ceramic		±55 to +165	°C

ELECTRICAL CHARACTERISTICS (VEE = ±5.2 V ±5%) (See Note)

			0°		25°			75°
Characteristic	Symbol	Min		Max	Min	Max	Min		Max	Unit
Power Supply Current	IE	Ð		165	Ð	150	Ð		165	mA
Input Current High	IinH									μA
Pins 5, 6, 11, 12, 13		Ð		430	Ð	275	Ð		275
Pin 9		Ð		670	Ð	420	Ð		420
Pin 7		Ð		535	Ð	335	Ð		335
Pin 10		Ð		380	Ð	240	Ð		240
Input Current Low	IinL	0.5		Ð	0.5	Ð	0.3		Ð	μA
High Output Voltage	VOH	±1.02		±0.84	±0.98	±0.81	±0.92		±0.735	Vdc
Low Output Voltage	VOL	±1.95		±1.63	±1.95	±1.63	±1.95		±1.60	Vdc
High Input Voltage	VIH	±1.17		±0.84	±1.13	±0.81	±1.07		±0.735	Vdc
Low Input Voltage	VIL	±1.95		±1.48	±1.95	±1.48	±1.95		±1.45	Vdc
AC PARAMETERS
Propagation Delay	tpd									ns
Clock to Q		0.7		2.3	0.7	2.4	0.7		2.5
Clock to Carry Out		1.0		4.8	1.0	4.9	1.0		5.0
Carry in to Carry
Out		0.7		2.5	0.7	2.6	0.7		2.7
Set-up Time	tset									ns
Data (D0 to C)		2.0		Ð	2.0	Ð	2.0		Ð
Select (S to C)		3.5		Ð	3.5	Ð	3.5		Ð
Carry In (Cin to C)		2.0		Ð	2.0	Ð	2.0		Ð
(C to Cin)		0		Ð	0	Ð	0		Ð
Hold Time	thold									ns
Data (C to D0)		0		Ð	0	Ð	0		Ð
Select (C to S)		±0.5		Ð	±0.5	Ð	±0.5		Ð
Carry In (C to Cin)		0		Ð	0	Ð	0		Ð
(Cin to C)		2.2		Ð	2.2	Ð	2.2		Ð
Counting Frequency	fcount	250		Ð	250	Ð	250		Ð	MHz
Rise Time	tr	0.5		2.3	0.5	2.4	0.5		2.5	ns
Fall Time	tf	0.5		2.3	0.5	2.4	0.5		2.5	ns

NOTE:

FUNCTION SELECT TABLE

CIN	S1	S2	Operating Mode
X	L	L	Preset (Program)
L	L	H	Increment (Count Up)
H	L	H	Hold Count
L	H	L	Decrement (Count Down)
H	H	L	Hold Count
X	H	H	Hold (Stop Count)

SEQUENTIAL TRUTH TABLE *

INPUTS

OUTPUTS

S1

S2

D0

D1

D2

D3

Carry

Clock

Q0

Q1

Q2

Q3

Carry

* *

In

Out

L

L

L

L

H

H

X

H

L

L

H

H

L

L

H

X

X

X

X

L

H

H

L

H

H

H

L

H

X

X

X

X

L

H

L

H

H

H

H

L

H

X

X

X

X

L

H

H

H

H

H

L

L

H

X

X

X

X

H

L

H

H

H

H

H

L

H

X

X

X

X

H

H

H

H

H

H

H

H

H

X

X

X

X

X

H

H

H

H

H

H

L

L

H

H

L

L

X

H

H

H

L

L

L

H

L

X

X

X

X

L

H

L

H

L

L

H

H

L

X

X

X

X

L

H

H

L

L

L

H

H

L

X

X

X

X

L

H

L

L

L

L

L

H

L

X

X

X

X

L

H

H

H

H

H

H

*Truth table shows logic states assuming inputs vary in sequence shown from top to bottom.

**A clock H is defined as a clock input transition from a low to a high logic level.

DIP PIN ASSIGNMENT

VCC1			1		16			VCC2
			2		15
Q2								Q1
Q3			3		14			Q0
			4		13			CLOCK
COUT
			5		12			D0
D3
D2			6		11			D1
			7		10
S2								CIN
			8		9
VEE								S1

Pin assignment is for Dual±in±Line Package. For PLCC pin assignment, see the Pin Conversion Tables on page 6±11 of the Motorola MECL Data Book (DL122/D).

Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 Iinear fpm is maintained. Outputs are terminated through a 50-ohm resistor to ±2.0 volts.

9/96

Motorola, Inc. 1996

2±1

REV 6

MC10H136

LOGIC DIAGRAM

S1 9

S2

7

Carry In

10

Q0

T

Q1

T

Q2

T

Q3

T

T

T

T

Q0

T

Q1

T

Q2

Q3

T

C

T

C

T C

T T C

Clock

13

12

14

11

15

6

2

5

3

4

D0

Q0

D1

Q1

D2

Q2

D3

Q3

Carry Out

VCC1 = Pin 1

VCC2 = Pin 16

VEE = Pin 8

NOTE: FLIP-FLOPS WILL TOGGLE WHEN ALL T INPUTS ARE LOW.

APPLICATION INFORMATION

The MC10H136 is a high speed synchronous counter that operates at 250 MHz. Counter operating modes include count up, count down, pre-set and hold count. This device allows the designer to use one basic counter for many applications.

The S1, S2, control lines determine the operating modes of the counter. In the pre-set mode, a clock pulse is necessary to load the counter with the information present on the data inputs (D0, D1, D2, and D3). Carry out goes low on the terminal count or when the counter is being pre-set.

MOTOROLA	2±2	MECL Data
		DL122 Ð Rev 6