MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Registered Hex TTL/ECL
Translator
The MC10H/100H604 is a 6±bit, registered, dual supply TTL to ECL translator. The device features differential ECL outputs as well as a choice between either a differential ECL clock input or a TTL clock input. The asynchronous master reset control is an ECL level input..
With its differential ECL outputs and TTL inputs the H604 device is ideally suited for the transmit function of a HPPI bus type board±to±board interface application. The on chip registers simplify the task of synchronizing the data between the two boards.
The device is available in either ECL standard: the 10H device is compatible with MECL 10KH logic levels while the 100H device is compatible with 100K logic levels.
•Differential 50Ω ECL Outputs
•Choice Between Differential ECL or TTL Clock Input
•Dual Power Supply
•Multiple Power and Ground Pins to Minimize Noise
•Specified Within±Device Skew
|
LOGIC SYMBOL |
|
|
|
|
|
|
|
|
1 OF 6 BITS |
|
|
|
|
|
|
|
Dn |
|
|
|
|
|
|
Qn |
|
|
D |
Q |
|
|
||||
|
|
|
||||||
|
|
|
|
|
||||
|
|
|
Qn |
|||||
|
|
|
|
|
|
|
||
CLK
R
CLK
CLK 
*
TCLK
MR
VBB
*1. When using MECL inputs, TCLK must be tied to ground (0V).
2.When using only one MECL input, the unused MECL input must be tied to VBB, and TCLK must be tied to ground (0V).
3.When using TCLK, both MECL inputs must be tied to VEE (±5.2V).
MC10H604
MC100H604
|
|
|
|
|
|
|
FN SUFFIX |
|
||
|
|
|
|
|
PLASTIC PACKAGE |
|
||||
|
|
|
|
|
|
|
CASE 776±02 |
|
||
|
|
|
|
|
|
|||||
PIN NAMES |
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
PIN |
|
|
|
FUNCTION |
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
D0±D5 |
|
|
TTL Data Inputs |
|
|||||
|
|
|
|
|
|
|
Differential ECL Clock Input |
|||
CLK, CLK |
|
|
||||||||
|
TCLK |
|
|
TTL Clock Input |
|
|||||
|
MR |
|
|
ECL Master Reset Input |
||||||
|
Q0±Q5 |
|
|
True ECL Outputs |
|
|||||
|
|
|
|
|
|
Inverted ECL Outputs |
||||
|
Q0±Q5 |
|
|
|||||||
|
VCCE |
|
|
ECL VCC (0V) |
|
|||||
|
VCCT |
|
|
TTL VCC (+5.0V) |
|
|||||
|
VEE |
|
|
ECL VEE (±5.2V) |
|
|||||
TRUTH TABLE |
|
|||||||||
|
|
|
|
|
|
|
|
|||
|
Dn |
|
MR |
|
TCLK/CLK |
|
Qn+1 |
|||
|
|
|
|
|
|
|
|
|||
|
L |
|
L |
|
Z |
|
L |
|||
|
H |
|
L |
|
Z |
|
H |
|||
|
X |
|
H |
|
X |
|
L |
|||
|
|
|
|
|
|
|
|
|
|
|
Z = LOW to HIGH Transition
Pinout: 28±Lead PLCC (Top View)
|
|
|
|
|
|
|
D1 |
D2 |
VCCT D3 |
D4 |
|
D5 VCCE |
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
25 |
24 |
23 |
|
22 |
|
21 |
|
20 |
|
19 |
|
|
|
|
|
||||
|
D0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
18 |
|
|
Q5 |
|||
|
26 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
TCLK |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
17 |
|
|
Q5 |
|||||
|
27 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
VBB |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
16 |
|
|
Q4 |
|||||
28 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Q4 |
|
|
CLK |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
15 |
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
CLK |
|
2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
14 |
|
|
VCCE |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
MR |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
13 |
|
|
Q3 |
|||
|
|
3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
VCCE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
12 |
|
|
Q3 |
|||||
|
4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
5 |
6 |
7 |
|
8 |
|
9 |
|
10 |
|
11 |
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
Q0 |
Q0 |
VEE |
Q1 |
Q1 |
Q2 |
Q2 |
|
|
|
|
||||||||
9/96
Motorola, Inc. 1996 |
2±302 |
REV 1 |
MC10H604 MC100H604
DC CHARACTERISTICS: VEE = VEE(Min) to VEE(Max); VCCE = GND; VCCT = 5.0V +10%
|
|
|
|
|
|
|
|
0°C |
|
|
|
25°C |
|
85°C |
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Symbol |
|
Parameter |
|
|
Min |
|
Max |
|
|
Min |
|
Max |
|
Min |
Max |
Unit |
|
|
Condition |
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IEE |
|
ECL Power Supply Current |
10H |
|
|
|
130 |
|
|
|
|
|
130 |
|
|
130 |
|
mA |
|
|
|
|
|
||||
|
|
|
|
|
100H |
|
|
|
130 |
|
|
|
|
|
140 |
|
|
150 |
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ICCH |
|
TTL Power Supply Current |
|
|
|
|
|
35 |
|
|
|
|
|
35 |
|
|
35 |
|
mA |
|
|
|
|
|
|||
|
ICCL |
|
|
|
|
|
|
|
|
45 |
|
|
|
|
|
45 |
|
|
45 |
|
|
|
|
|
|
|
||
|
10H ECL DC CHARACTERISTICS: VCCT = +5.0 V ± 10%; VEE = ± 5.20 V ±5% |
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||
|
|
|
|
|
|
|
|
0°C |
|
|
|
25°C |
|
85°C |
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
Symbol |
|
Parameter |
|
|
Min |
|
Max |
|
|
Min |
|
Max |
|
Min |
Max |
Unit |
|
|
Condition |
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IIH |
|
Input HIGH Current |
|
|
|
|
|
225 |
|
|
|
|
|
145 |
|
|
145 |
|
μA |
|
|
|
|
|
|||
|
IIL |
|
Input LOW Current |
|
|
0.5 |
|
|
|
|
|
|
0.5 |
|
|
|
0.5 |
|
|
μA |
|
|
|
|
|
|||
|
VIH |
|
Input HIGH Voltage |
|
|
±1170 |
|
±840 |
|
±1130 |
|
±810 |
±1060 |
±720 |
|
mV |
|
|
|
|
|
|||||||
|
VIL |
|
Input LOW Voltage |
|
|
±1950 |
|
±1480 |
±1950 |
|
±1480 |
±1950 |
±1480 |
|
|
|
|
|
|
|
||||||||
|
VBB |
|
Output Bias Voltage |
|
|
±1400 |
|
±1290 |
±1370 |
|
±1270 |
±1330 |
±1210 |
|
mV |
|
|
|
|
|
||||||||
|
VOH |
|
Output HIGH Voltage |
|
|
±1020 |
|
±840 |
|
±980 |
|
±810 |
±910 |
±720 |
|
mV |
|
|
50 Ω to ± 2.0 V |
|
||||||||
|
VOL |
|
Output LOW Voltage |
|
|
±1950 |
|
±1630 |
±1950 |
|
±1630 |
±1950 |
±1595 |
|
|
|
|
|
|
|
||||||||
|
100H ECL DC CHARACTERISTICS: VCCT = 5.0 V ± 10%; VEE = ± 4.2 V to ± 5.5 V |
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||
|
|
|
|
|
|
|
|
0°C |
|
|
|
25°C |
|
85°C |
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
Symbol |
|
Parameter |
|
|
Min |
|
Max |
|
|
Min |
|
Max |
|
Min |
Max |
Unit |
|
|
Condition |
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IIH |
|
Input HIGH Current |
|
|
|
|
|
225 |
|
|
|
|
|
145 |
|
|
145 |
|
μA |
|
|
|
|
|
|||
|
IIL |
|
Input LOW Current |
|
|
0.5 |
|
|
|
|
|
|
0.5 |
|
|
|
0.5 |
|
|
μA |
|
|
|
|
|
|||
|
VIH |
|
Input HIGH Voltage |
|
|
±1165 |
|
±880 |
|
±1165 |
|
±880 |
±1165 |
±880 |
|
mV |
|
|
|
|
|
|||||||
|
VIL |
|
Input LOW Voltage |
|
|
±1810 |
|
±1475 |
±1810 |
|
±1475 |
±1810 |
±1475 |
|
|
|
|
|
|
|
||||||||
|
VBB |
|
Output Bias Voltage |
|
|
±1400 |
|
±1280 |
±1400 |
|
±1280 |
±1400 |
±1280 |
|
mV |
|
|
|
|
|
||||||||
|
VOH |
|
Output HIGH Voltage |
|
|
±1025 |
|
±880 |
|
±1025 |
|
±880 |
±1025 |
±880 |
|
mV |
|
|
50 Ω to ± 2.0 V |
|
||||||||
|
VOL |
|
Output LOW Voltage |
|
|
±1810 |
|
±1620 |
±1810 |
|
±1620 |
±1810 |
±1620 |
|
|
|
|
|
|
|
||||||||
|
TTL DC CHARACTERISTICS: VCCT = 5.0 V ± 10%; VEE = ± 5.2 V ± 5% (10H version); VEE = ± 4.2 V to ± 5.5 V (100H version) |
|||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
0°C |
|
|
|
25°C |
|
85°C |
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
Symbol |
|
Parameter |
|
|
Min |
|
Max |
|
|
Min |
|
Max |
|
Min |
Max |
Unit |
|
|
Condition |
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
VIH |
|
Input HIGH Voltage |
|
|
2.0 |
|
|
|
|
|
|
2.0 |
|
|
|
2.0 |
|
|
V |
|
|
|
|
|
|||
|
VIL |
|
Input LOW Voltage |
|
|
|
|
|
0.8 |
|
|
|
|
|
0.8 |
|
|
0.8 |
|
V |
|
|
|
|
|
|||
|
IIH |
|
Input HIGH Current |
|
|
|
|
|
20 |
|
|
|
|
|
20 |
|
|
20 |
|
μA |
|
VIN = 2.7 V |
|
|||||
|
|
|
|
|
|
|
|
|
|
100 |
|
|
|
|
|
100 |
|
|
100 |
|
|
|
VIN = 7.0 V |
|
||||
|
IIL |
|
Input LOW Current |
|
|
|
|
|
± 0.6 |
|
|
|
|
|
± 0.6 |
|
|
± 0.6 |
|
mA |
|
VIN = 0.5 V |
|
|||||
|
VIK |
|
Input Clamp Voltage |
|
|
|
|
|
±1.2 |
|
|
|
|
|
±1.2 |
|
|
±1.2 |
|
V |
|
IIN = ±18 mA |
|
|||||
|
AC CHARACTERISTICS: VCCT = 5.0 V ± 10%; VEE = ± 5.2 V ± 5% (10H version); VEE = ± 4.2 V to ± 5.5 V (100H version) |
|||||||||||||||||||||||||||
|
|
|
|
|
|
|
0°C |
|
|
|
|
|
|
25°C |
|
|
|
|
85°C |
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
Symbol |
|
Parameter |
Min |
|
Typ |
|
Max |
|
Min |
|
Typ |
|
Max |
|
Min |
Typ |
|
Max |
Unit |
|
Condition |
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
tPLH |
Propagation Delay |
CLK to Q |
1.5 |
|
|
|
3.5 |
|
1.5 |
|
|
|
|
3.5 |
|
1.5 |
|
|
3.5 |
|
ns |
|
CL = 50pF |
|
|||
|
tPHL |
to Output |
TCLK to Q |
2.0 |
|
|
|
4.0 |
|
2.0 |
|
|
|
|
4.0 |
|
2.0 |
|
|
4.0 |
|
|
|
|
|
|||
|
|
|
|
MR to Q |
1.5 |
|
|
|
4.0 |
|
1.5 |
|
|
|
|
4.0 |
|
1.5 |
|
|
4.0 |
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
ts |
Setup Time |
|
1.5 |
|
0.5 |
|
|
|
|
1.5 |
|
0.5 |
|
|
|
1.5 |
0.5 |
|
|
|
ns |
|
CL = 50pF |
|
|||
|
tH |
Hold Time |
|
1.5 |
|
0.5 |
|
|
|
|
1.5 |
|
0.5 |
|
|
|
1.5 |
0.5 |
|
|
|
ns |
|
CL = 50pF |
|
|||
|
tPW |
Minimum Pulse Width |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ns |
|
CL = 50pF |
|
||
|
|
|
|
CLK, MR |
|
|
1.0 |
|
|
|
|
|
|
|
1.0 |
|
|
|
|
1.0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
VPP |
Minimum Input Swing |
|
|
|
|
|
|
|
|
|
|
150 |
|
|
|
|
|
|
|
|
mV |
|
|
|
|||
|
tr |
Rise/Fall Times |
|
0.3 |
|
1.0 |
|
2.0 |
|
0.3 |
|
1.0 |
|
2.0 |
|
0.3 |
1.0 |
|
2.0 |
|
ns |
|
20% ± 80% |
|
||||
|
tf |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
MECL Data |
|
|
|
|
|
2±303 |
|
|
|
|
|
|
|
|
|
|
|
|
MOTOROLA |
||||||||
|
DL122 Ð Rev 6 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
Loading...