magicolor® 2400W
WarrantyExchange Guide
1760665-001B
Trademarks
KONICA MINOLTA and the KONICA MINOLTA logo are trademarks or registered trademarks of KONICA MINOLTA HOLDINGS, INC.
magicolor is a trademark or registered trademark of KONICA MINOLTA PRINTING SOLUTIONS U.S.A., INC. All other trademarks are the property of their respective owners.
Copyright Notice
Copyright © 2005 KONICA MINOLTA PRINTING SOLUTIONS U.S.A., INC., One Magnum Pass, Mobile, AL 36618, USA. All Rights Reserved. This document may not be copied, in whole or part, nor transferred to any other media or language, without written permission of KONICA MINOLTA BUSINESS TECHNOLOGIES, INC.
Manual Notice
KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. reserves the right to make changes to this manual and to the equipment described herein without notice. Considerable effort has been made to ensure that this manual is free of inaccuracies and omissions. However, KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. makes no warranty of any kind including, but not limited to, any implied warranties of merchantability and fitness for a particular purpose with regard to this manual. KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. assumes no responsibility for, or liability for, errors contained in this manual or for incidental, special, or consequential damages arising out of the furnishing of this manual, or the use of this manual in operating the equipment, or in connection with the performance of the equipment when so operated.
Introduction
Thank you for contacting a technical support representative to obtain information about returning your printer for warranty exchange. Follow these instructions very carefully.
If you need additional assistance, refer to the General Information Guide (included with the original printer) or printer.konicaminolta.com for worldwide sources of service and support.
Attention
Failure to follow these instructions could result in voiding your warranty.
Exchange Procedure
Each of these steps is explained in detail in this guide. |
|
||
|
|
|
|
|
1 |
Unpack the exchange printer. |
See page 2. |
|
2 |
Prepare the original printer—turn it off, unplug the |
See page 4. |
|
|
power cord, and remove the interface cables and dust |
|
|
|
cover. |
|
|
|
|
|
|
3 |
Move the consumables (the four toner cartridges, the |
See page 6. |
|
|
drum cartridge, and the transfer belt unit) from the origi- |
|
|
|
nal printer to the exchange printer. |
|
|
|
|
|
|
4 |
Finish setting up the exchange printer—plug it in, attach |
See page 12. |
|
|
the interface cables, turn it on, install the dust cover, and |
|
|
|
fill the tray with media. |
|
|
|
|
|
|
5 |
Repack the original printer, and call the shipper for |
See page 14. |
|
|
pickup. |
|
Introduction |
1 |
Unpack the Exchange Printer
Attention
Use caution when unpacking the exchange printer, so the packaging (including the tape) can be used to repack the printer to be returned.
Exchange
Exchange
1 Unpack the exchange printer.
WARNING! 
The printer weighs approximately 40 lbs/18 kg without consumables. Be sure to have help when lifting and moving it.
2 Remove the tape from the outside of the exchange printer.
2 |
Unpack the Exchange Printer |
3 Open the input and exit trays on the exchange printer.
Exchange
4 Remove the fuser separators from the exchange printer.
See the instructions on the fuser separator tag for complete details.
A |
B |
Exchange |
C |
|
D |
Unpack the Exchange Printer |
3 |
Prepare the Original Printer
1 Turn off the original printer, unplug the power cord, and remove the interface cable.
A |
B |
Original |
C |
|
4 |
Prepare the Original Printer |
Loading...