SGS Thomson Microelectronics TL064ID, TL064I, TL064M, TL064IN, TL064ACD Datasheet

TL064

TL064A - TL064B

LOW POWER J-FET QUAD OPERATIONAL AMPLIFIERS

■VERY LOW POWER CONSUMPTION : 200μA

■WIDE COMMON-MODE (UP TO VCC+) AND DIFFERENTIAL VOLTAGE RANGES

■LOW INPUT BIAS AND OFFSET CURRENTS

■OUTPUT SHORT-CIRCUIT PROTECTION

■HIGH INPUT IMPEDANCE J-FET INPUT STAGE

■INTERNAL FREQUENCY COMPENSATION

■LATCH UP FREE OPERATION

■HIGH SLEW RATE : 3.5V/μs

N	D
DIP14	SO14
(Plastic Package)	(Plastic Micropackage)

DESCRIPTION

The TL064, TL064A and TL064B are high speed J-FET input quad operational amplifiers. Each of these J-FET input operational amplifiers incorporates well matched, high voltage J-FET and bipolar transistors in a monolithic integrated circuit.

The device features high slew rate, low input bias and offsetcurrents, andlow offset voltage temperature coefficient.

PIN CONNECTIONS (top view)

ORDER CODES

	Part Number	Temperature Range	Package
			N	D
	TL064M/AM/BM	-55oC, +125oC	•	•
	TL064I/AI/BI	-40oC, +105oC	•	•
	TL064C/AC/BC	0oC, +70oC	•	•

Example : TL064IN

Output 1 1				14	Output 4
Inverting Input 1	2	-	-	13	Inverting Input 4
Non-inverting Input 1	3	+	+	12	Non-inverting Input 4
VCC +	4			11	VCC -
Non-inverting Input 2	5	+	+	10	Non-inverting Input 3
Inverting Input 2	6	-	-	9	Inverting Input 3
Output 2	7			8	Output 3

October 1997

1/10

TL064 - TL064A - TL064B

SCHEMATIC DIAGRAM

VCC

		220Ω
Inverting	Non-inverting		1/4 TL064
Input	Input	Ω Output
		64
		45k Ω
		270Ω	Ω
		3.2k

4.2k Ω 100Ω

VCC

MAXIMUM RATINGS

Symbol	Parameter	TL064M,AM,BM	TL064I,AI,BI	TL064C,AC,BC	Unit
VCC	Supply Voltage - (note 1)	±18	±18	±18	V
Vi	Input Voltage - (note 3)	±15	±15	±15	V
Vid	Differential Input Voltage - (note 2)	±30	±30	±30	V
Ptot	Power Dissipation	680	680	680	mW
	Output Short-Circuit Duration (Note 4)	Infinite	Infinite	Infinite
Toper	Operating Free-Air Temperature	-55 to +125	-40 to +105	0 to +70	oC
	Range
Tstg	Storage Temperature Range	-65 to +150	-65 to +150	-65 to +150	oC

Notes : 1. All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the zero reference level is the midpoint between VCC+ and VCC-.

2.Differential voltages are the non-inverting input terminal with respect to the inverting input terminal.

3.The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less.

4.The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded.

2/10

TL064 - TL064A - TL064B

ELECTRICAL CHARACTERISTICS

VCC = ± 15V, Tamb = 25oC (unless otherwise specified)

Symbol	Parameter
Vio	Input Offset Voltage (Rs = 50Ω)
	Tamb = 25oC
	Tmin. ≤ Tamb ≤ Tmax.
DVio	Temperature Coefficient of Input
	Offset Voltage (Rs = 50Ω)
Iio	Input Offset Current *
	Tamb = 25oC
	Tmin. ≤ Tamb ≤ Tmax.
Iib	Input Bias Current *
	Tamb = 25oC
	Tmin. ≤ Tamb ≤ Tmax.
Vicm	Input Common Mode Voltage
	Range
VOPP	Output Voltage Swing (RL = 10kΩ)
	Tamb = 25oC
	Tmin. ≤ Tamb ≤ Tmax.
Avd	Large Signal Voltage Gain
	(RL = 10kΩ, Vo = ± 10V)
	Tamb = 25oC
	Tmin. ≤ Tamb ≤ Tmax.
GBP	Gain Bandwidth Product
	(Tamb = 25oC, RL = 10kΩ
	CL = 100pF)
Ri	Input Resistance
CMR	Common Mode Rejection Ratio
	(Rs = 50Ω)
SVR	Supply Voltage Rejection Ratio
	(Rs = 50Ω)
Icc	Supply Current (Per Amplifier)
	(Tamb = 25oC, no load, no signal)
VO1/VO2	Channel Separation
	(Av = 100, Tamb = 25oC)
PD	Total Power Consumption
	(Tamb = 25oC, no load, no signal)

	TL064M				TL064I			TL064C		Unit
	Min. Typ. Max. Min. Typ. Max. Min. Typ. Max.
		3	6		3	6		3	15	mV
			15			9			20
		10			10			10		μV/oC
		5	100		5	100		5	200	pA
			20			10			5	nA
		30	200		30	200		30	400	pA
			50			20			10	nA
	±11.5	+15		±11.5	+15		±11	+15		V
		-12			-12			-12
	20	27		20	27		20	27		V
	20			20			20
										V/mV
	4	6		4	6		3	6
	4			4			3
										MHz
		1			1			1
		1012			1012			1012		Ω
	80	86		80	86		70	76		dB
	80	95		80	95		70	95		dB
		200	250		200	250		200	250	μA
		120			120			120		dB
		6	7.5		6	7.5		6	7.5	mW

* The input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive. Pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature as possible.

ELECTRICAL CHARACTERISTICS (continued)

VCC = ± 15V, Tamb = 25oC

	Symbol	Parameter		TL064C,I,M	Unit
			Min.	Typ.
					Max.
	SR	Slew Rate (Vi = 10V, RL = 10kΩ, CL = 100pF, AV = 1)	1.5	3.5	V/μs
	tr	Rise Time (Vi = 20mV, RL = 10kΩ, CL = 100pF, AV = 1) (see Figure 1)		0.2	μs
	KOV	Overshoot Factor (Vi = 20mV, RL = 10kΩ, CL = 100pF, AV = 1)		10	%
		(see figure 1)
	en	Equivalent Input Noise Voltage		42	nV
		(R = 100Ω, f = 1KHz)			```√
		s			Hz

3/10