SGS Thomson Microelectronics TL061CN, TL061C, TL061CD, TL061ACN, TL061ACD Datasheet

TL061

TL061A - TL061B

LOW POWER J-FET SINGLE OPERATIONAL AMPLIFIER

.

.VERY LOW POWER CONSUMPTION : 200μA

WIDE COMMON-MODE (UP TO VCC+) AND

.DIFFERENTIAL VOLTAGE RANGES

.LOW INPUT BIAS AND OFFSET CURRENTS

.OUTPUT SHORT-CIRCUIT PROTECTION HIGH INPUT IMPEDANCE J-FET INPUT

.STAGE

.INTERNAL FREQUENCY COMPENSATION

.LATCH UP FREE OPERATION HIGH SLEW RATE : 3.5V/μs

DESCRIPTION

The TL061, TL061A and TL061B are high speed J-FET input single operational amplifier family. Each of these J-FET input operational amplifiers incorporates well matched, high voltage J-FET and bipolar transistors in a monolithic integrated circuit. The devices feature high slew rates, low input bias and offsetcurrents, andlow offset voltage temperature coefficient.

PIN CONNECTIONS (top view)

1	8
2	7
3	6
4	5

N	D
DIP8	SO8
(Plastic Package)	(Plastic Micropackage)

ORDER CODES

	Part Number	Temperature Range	Package
			N	D
	TL061M/AM/BM	-55oC, +125oC	●	●
	TL061I/AI/BI	-40oC, +105oC	●	l
	TL061C/AC/BC	0oC, +70oC	●	l

Example : TL061IN

1- Offset Null 1

2- Inverting input

3- Non-inverting input

4- VCC-

5- Offset Null 2

6- Output

7- VCC+

8- N.C.

October 1997

1/9

TL061 - TL061A - TL061B

SCHEMATIC DIAGRAM

V C C

			220 Ω
Inverting		Non-inverting
	Input	Input	64 Ω	Output
		45k Ω
			270 Ω	3.2k Ω
	4.2k Ω		Ω
		100
					VCC
	Offset Null 1	Offset Null 2
INPUT OFFSET VOLTAGE NULL CIRCUIT
		TL061
	N1	N2
		100k Ω
		V CC
MAXIMUM RATINGS
Symbol		Parameter	TL061M,AM,BM	TL061I,AI,BI	TL061C,AC,BC	Unit
VCC	Supply Voltage - (note 1)		±18	±18	±18	V
Vi	Input Voltage - (note 3)		±15	±15	±15	V
Vid	Differential Input Voltage - (note 2)		±30	±30	±30	V
Ptot	Power Dissipation		680	680	680	mW
	Output Short-Circuit Duration (Note 4)		Infinite	Infinite	Infinite
Toper	Operating Free-Air Temperature Range		-55 to +125	-40 to +105	0 to +70	oC
Tstg	Storage Temperature Range		- 65 to + 150	- 65 to + 150	- 65 to + 150	oC
Notes : 1.	All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where
	the zero reference level is the midpoint between VCC+ and VCC-.
2.	Differential voltages are the non-inverting input terminal with respect to the inverting input terminal.

3.The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less.

4.The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded.

2/9

								TL061 - TL061A - TL061B
ELECTRICAL CHARACTERISTICS
VCC = ± 15V, Tamb = 25oC (unless otherwise specified)
Symbol		Parameter	TL061M				TL061I			TL061C		Unit
			Min. Typ. Max. Min. Typ. Max. Min. Typ. Max.
Vio	Input Offset Voltage (Rs = 50Ω)											mV
	Tamb = 25oC			3	6		3	6		3	15
	Tmin. ≤ Tamb ≤ Tmax.				9			9			20
DVio	Temperature Coefficient of Input											μV/oC
	Offset Voltage (Rs = 50Ω)			10			10			10
Iio	Input Offset Current *
	Tamb = 25oC			5	100		5	100		5	200	pA
	Tmin. ≤ Tamb ≤ Tmax.				20			10			5	nA
Iib	Input Bias Current *
	Tamb	= 25oC		30	200		30	200		30	400	pA
	Tmin.	≤ Tamb ≤ Tmax.			50			20			10	nA
Vicm	Input Common Mode Voltage		±11.5	+15		±11.5	+15		±11	+15		V
	Range			-12			-12			-12
VOPP	Output Voltage Swing (RL = 10kΩ)											V
	Tamb = 25oC		20	27		20	27		20	27
	Tmin. ≤ Tamb ≤ Tmax.		20			20			20
Avd	Large Signal Voltage Gain											V/mV
	(RL = 10kΩ, Vo = ± 10V)
	Tamb = 25oC		4	6		4	6		3	6
	Tmin. ≤ Tamb ≤ Tmax.		4			4			3
GBP	Gain Bandwidth Product											MHz
	(Tamb = 25oC, RL = 10kΩ
	CL = 100pF)			1			1			1
Ri	Input Resistance			1012			1012			1012		Ω
CMR	Common Mode Rejection Ratio											dB
	(Rs = 50Ω)		80	86		80	86		70	76
SVR	Supply Voltage Rejection Ratio											dB
	(Rs = 50Ω)		80	95		80	95		70	95
Icc	Supply Current											μA
	(Tamb = 25oC, no load, no signal)			200	250		200	250		200	250
PD	Total Power Consumption											mW
	(Tamb = 25oC, no load, no signal)			6	7.5		6	7.5		6	7.5

*The input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive. Pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature as possible.

ELECTRICAL CHARACTERISTICS (continued)

VCC = ± 15V, Tamb = 25oC

	Symbol	Parameter		TL061C,I,M	Unit
			Min.	Typ.
					Max.
	SR	Slew Rate (Vi = 10V, RL = 10kΩ, CL = 100pF, AV = 1)	1.5	3.5	V/μs
	tr	Rise Time (Vi = 20mV, RL = 10kΩ, CL = 100pF, AV = 1)		0.2	μs
	KOV	Overshoot Factor (Vi = 20mV, RL = 10kΩ, CL = 100pF, AV = 1)			%
		(see figure 1)		10
	en	Equivalent Input Noise Voltage			nV
		(Rs = 100Ω, f = 1KHz)		42	```√ Hz

3/9