INTEGRATED CIRCUITS
TDA1553Q
2 x 22 W BTL stereo car radio power amplifier with loudspeaker protection
Product specification |
|
July 1994 |
|||||
File under Integrated Circuits, IC01 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Philips Semiconductors |
Product specification |
|
|
2 x 22 W BTL stereo car radio power
TDA1553Q
amplifier with loudspeaker protection
The TDA1553Q is an integrated class-B output amplifier in a 13-lead singe-in-line (SIL) plastic power package.
The circuit contains 2 x 22 W amplifiers in Bridge Tied Load (BTL) configuration. The device is primarily developed for car radio applications.
Features |
|
|
|
∙ |
Requires very few external components |
∙ |
Thermally protected |
∙ |
High output power |
∙ |
Reverse polarity safe |
∙ |
Low offset voltage at outputs |
∙ |
Capability to handle high energy on outputs (VP = 0 V) |
∙ |
Fixed gain |
∙ |
Protected against electrostatic discharge |
∙ |
Good ripple rejection |
∙ |
No switch-on/switch-off plop |
∙ |
Mute/stand-by switch |
∙ |
Low thermal resistance |
∙ |
Load dump protection |
∙ |
Flexible leads |
∙AC and DC short-circuit-safe to ground and VP
∙Loudspeaker protection (LSP)
PARAMETER |
CONDITIONS |
|
SYMBOL |
MIN. |
TYP. |
MAX. |
UNIT |
|
|
|
|
|
|
|
|
Supply voltage range |
|
|
|
|
|
|
|
operating |
|
VP |
6.0 |
14.4 |
18.0 |
V |
|
non-operating |
|
VP |
− |
− |
30 |
V |
|
load dump protected |
|
VP |
− |
− |
45 |
V |
|
Repetitive peak output |
|
|
|
|
|
|
|
current |
|
IORM |
− |
− |
4 |
A |
|
Total quiescent current |
|
Itot |
− |
80 |
160 |
mA |
|
Stand-by current |
|
Isb |
− |
0.1 |
100 |
μA |
|
Switch-on current |
|
Isw |
− |
− |
60 |
μA |
|
Input impedance |
|
|ZI| |
50 |
60 |
75 |
kΩ |
|
Junction temperature |
|
Tj |
|
− |
− |
150 |
°C |
Stereo application |
|
|
|
|
|
|
|
Output power |
RL= 4 Ω; THD = 10% |
Po |
20 |
22 |
− |
W |
|
Supply voltage ripple |
|
|
|
|
|
|
|
rejection |
RS = 0 Ω |
|
|
|
|
|
|
|
f = 100 Hz to 10 kHz |
RR |
48 |
− |
− |
dB |
|
DC output offset voltage |
|
| |
VO| |
− |
− |
150 |
mV |
Channel separation |
|
α |
|
40 |
− |
− |
dB |
Channel unbalance |
|
| |
Gv| |
− |
− |
1 |
dB |
|
|
|
|
|
|
|
|
13-lead SIL-bent-to-DIL; plastic power (SOT141R); SOT141-6; 1996 July 24.
July 1994 |
2 |
Philips Semiconductors |
Product specification |
|
|
2 x 22 W BTL stereo car radio power
TDA1553Q
amplifier with loudspeaker protection
|
|
|
|
VP1 |
VP2 |
|
|
|
|
|
3 |
10 |
|
1 |
mute switch |
Cm |
|
|
|
|
input 1 |
|
|
|
|
|
|
|
|
|
|
TDA1553Q |
|
|
|
VA |
|
|
|
4 |
output 1A |
|
|
|
|
|
||
|
2 |
|
|
|
|
|
|
kΩ |
|
|
PROTECTIONS |
|
|
|
18 kΩ |
|
|
Load dump |
|
|
|
|
power stage |
Soar |
|
|
|
|
|
|
|
|
||
|
|
|
|
Thermal |
|
|
|
|
|
|
Short - circuit |
|
|
|
mute switch |
Cm |
|
Reverse polarity |
|
|
|
|
|
|
Loudspeaker |
|
|
|
VA |
|
|
|
6 |
output 1B |
60 |
|
|
|
|
||
|
|
|
|
|
||
|
|
|
|
|
|
|
kΩ |
2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
kΩ |
|
|
|
|
|
|
18 kΩ |
|
power stage |
|
|
|
|
|
|
|
|
|
|
|
VP |
|
|
|
|
|
|
|
|
|
|
11 |
mute/stand-by |
|
stand-by |
|
|
|
|
|
|
|
|
|
|
loudspeaker |
|
|
switch |
|
stand-by |
|
12 |
|
|
|
|
|
protection |
||
|
|
|
reference |
|
|
|
|
|
|
|
|
|
|
|
VA |
|
voltage |
|
|
|
|
15 kΩ |
|
|
|
|
|
|
x1 |
|
mute |
loudspeaker |
|
|
|
|
protection |
|
|
||
|
|
|
|
|
||
|
|
|
switch |
|
|
|
|
15 kΩ |
|
|
|
|
|
|
Vref |
|
|
|
|
|
13 |
mute switch |
Cm |
|
|
|
|
input 2 |
|
|
|
|
|
|
|
VA |
|
|
|
9 |
output 2B |
|
|
|
|
|
||
|
|
|
|
|
|
|
|
2 |
|
|
|
|
|
|
kΩ |
|
|
|
|
|
|
18 kΩ |
|
power stage |
|
|
|
|
|
|
|
|
|
|
|
mute switch |
Cm |
|
|
|
|
|
VA |
|
|
|
7 |
output 2A |
60 |
|
|
|
|
||
|
|
|
|
|
|
|
kΩ |
2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
kΩ |
|
|
|
|
|
Vref |
18 kΩ |
|
power stage |
|
|
|
|
|
|
|
|
|
|
|
2 |
5 |
8 |
|
|
|
|
|
GND1 |
GND2 |
|
MLB953 |
|
ground (signal)
power ground (substrate)
Fig.1 Block diagram.
July 1994 |
3 |