Philips TDA1517P-N2, TDA1517-N3-S5, TDA1517-N3, TDA1517-N2-S5, TDA1517-N2 Datasheet

INTEGRATED CIRCUITS

DATA SHEET

TDA1517; TDA1517P

2 × 6 W stereo power amplifier

Product specification

1998 Apr 28

Supersedes data of 1995 Dec 15

File under Integrated Circuits, IC01

Philips Semiconductors	Product specification
2 × 6 W stereo power amplifier	TDA1517; TDA1517P

FEATURES

∙Requires very few external components

∙High output power

∙Fixed gain

∙Good ripple rejection

∙Mute/standby switch

∙AC and DC short-circuit safe to ground and VP

∙Thermally protected

∙Reverse polarity safe

∙Capability to handle high energy on outputs (VP = 0 V)

∙No switch-on/switch-off plop

∙Electrostatic discharge protection.

QUICK REFERENCE DATA

GENERAL DESCRIPTION

The TDA1517 is an integrated class-B dual output amplifier in a plastic single in-line medium power package with fin (SIL9MPF) and a plastic heat-dissipating dual in-line package (HDIP18). The device is primarily developed for multi-media applications.

SYMBOL	PARAMETER		CONDITIONS	MIN.	TYP.	MAX.	UNIT
VP	supply voltage			6.0	14.4	18.0	V
IORM	repetitive peak output current			−	−	2.5	A
Iq(tot)	total quiescent current			−	40	80	mA
Isb	standby current			−	0.1	100	μA
Isw	switch-on current			−	−	40	μA
|ZI|	input impedance			50	−	−	kΩ
Po	output power		RL = 4 Ω; THD = 0.5%	−	5	−	W
			RL = 4 Ω; THD = 10%	−	6	−	W
SVRR	supply voltage ripple rejection		fi = 100 Hz to 10 kHz	48	−	−	dB
αcs	channel separation			40	−	−	dB
Gv	closed loop voltage gain			19	20	21	dB
Vno(rms)	noise output voltage (RMS value)			−	50	−	μV
Tc	crystal temperature			−	−	150	°C
ORDERING INFORMATION
TYPE			PACKAGE
NUMBER	NAME		DESCRIPTION			VERSION
TDA1517	SIL9MPF	plastic single in-line medium power package with fin; 9 leads				SOT110-1
TDA1517P	HDIP18	plastic heat-dissipating dual in-line package; 18 leads				SOT398-1

1998 Apr 28

2

Philips Semiconductors	Product specification
2 × 6 W stereo power amplifier	TDA1517; TDA1517P
BLOCK DIAGRAM

non-inverting	1	mute switch	Cm
input 1
	60
	kΩ
					4	output 1
		VA
	2
	kΩ
		18 kΩ			power stage
		VP
					8	mute/stand-by
		stand-by				switch input
		switch			stand-by
					reference
		VA			voltage
		15 kΩ
		x 1			mute
supply voltage
	3				switch
ripple rejection		15 kΩ
output
		mute
		reference
		voltage			TDA1517
		18 kΩ
	2
	kΩ
non-inverting	9	VA			6	output 2
input 2
	60
	kΩ		Cm
	input	mute switch
					power stage
	reference
		signal			power
	voltage
		ground			ground
		2	7	5	(substrate)
					MLC351
		SGND	VP	PGND

Fig.1 Block diagram.

1998 Apr 28

3

Philips Semiconductors		Product specification
2 × 6 W stereo power amplifier		TDA1517; TDA1517P
PINNING
SYMBOL	PIN	DESCRIPTION
−INV1	1	non-inverting input 1
SGND	2	signal ground
SVRR	3	supply voltage ripple rejection output
OUT1	4	output 1
PGND	5	power ground
OUT2	6	output 2
VP	7	supply voltage
M/SS	8	mute/standby switch input
−INV2	9	non-inverting input 2

ndbook, halfpage					ndbook, halfpage
		INV1	1				INV1	1		18
	SGND		2			SGND		2		17
	SVRR					SVRR
			3					3		16
	OUT1		4			OUT1		4		15
	PGND					PGND
			5	TDA1517				5	TDA1517P	14
	OUT2					OUT2
			6					6		13
		VP					VP
			7					7		12
	M/SS					M/SS
			8					8		11
		INV2					INV2
			9					9		10
				MLC352					MLC353

Pins 10 to 18 should be connected to GND or floating.

Fig.2 Pin configuration for SOT110-1.

Fig.3 Pin configuration for SOT398-1.

FUNCTIONAL DESCRIPTION

The TDA1517 contains two identical amplifiers with differential input stages. The gain of each amplifier is fixed at 20 dB. A special feature of the device is the mute/standby switch which has the following features:

∙Low standby current (<100 μA)

∙Low mute/standby switching current (low cost supply switch)

∙Mute condition.

1998 Apr 28

4