Installation and Care Guide
Floor-Mount Bath Faucet
K-T97328-4 |
|
K-T97331-4 |
K-T97332-4 |
|
K-T97344-4 |
Français, page “Français-1”
Español, página “Español-1”
1240535-2-D
Tools
|
Plus: |
|
• 3/16" Masonry Bit (for concrete installation) |
Sealant Tape |
• Conventional Woodworking Tools |
• Plumbing Tools and Materials |
Important Information
CAUTION: Risk of personal injury. Do not use the bath filler as a grab bar or support bar when entering or exiting the bath. The bath filler is not designed to support weight.
NOTICE: To avoid damage to the O-rings on the bottom of the faucet, keep the faucet vertical and use care when installing the faucet.
NOTE: A minimum operating pressure of 45 psi (310 kPa) is required for proper operation. If a pressure of less than 45 psi (310 kPa) is present, contact a plumber or choose another faucet.
For use with automatic compensating valves rated at 1.6 gal/min (6.1 l/min) or less.
Observe all local plumbing and building codes.
Shut off the water supply.
A drill bit is provided for installation to wood support. Use an appropriate drill bit for other materials.
The dimensions given assume the spout and bath are mounted on the same surface. Adjust the dimensions accordingly if the spout and bath are mounted on different surfaces.
If this product is installed with an overflowing bath, the outer rim of the bath should slightly overlap the 2x4 framing.
Installer supplied copper tubing must be 5/8″ OD (1/2″ Nominal).
Carefully review this document and any appropriate rough-in sheets. Design the bath enclosure accordingly.
1240535-2-D |
2 |
Kohler Co. |
Important Information (cont.)
The appearance of your faucet may differ from the illustrations in this guide. The instructions still apply.
Kohler Co. |
3 |
1240535-2-D |
Finished
Floor
Subfloor
2-1/4"
(57 mm) Min
3-1/6"
(78 mm) Max
Wood Support
Base |
7-7/8" |
|
(200 mm) |
||
Centerline |
Min |
|
2-3/4" |
Finished |
|
(70 mm) |
||
Wall |
||
Min |
||
|
||
Bath |
|
|
Finished |
|
|
Floor |
|
1. Prepare the Site
IMPORTANT! 2x6 lumber is NOT adequate for this application.
1240535-2-D |
4 |
Kohler Co. |
Prepare the Site (cont.)
NOTICE: Adequate floor support is required. The wood support must be a minimum of 2″ (51 mm) thick by 6″ (152 mm) wide. 2x6 lumber is NOT adequate for this application.
NOTE: Concrete can be used as the floor support.
Plan out the bath filler placement based on the dimensions above.
Cut a hole in the subfloor large enough to install the wood support between two floor joists.
Secure a wood support 2-1/4″ (57 mm) - 3-1/16″ (78 mm) below the height of the finished floor.
Kohler Co. |
5 |
1240535-2-D |
Top View
Hot
Pencil
Cold
Wall
Bath
2. Spout Orientation
NOTE: Verify correct spout orientation before securing the base to the wooden support.
NOTE: The base has a blue mark and a notch on the cold supply side.
Orient the base with the cold supply side notch placed in the direction shown.
If possible, dry fit the faucet to the base using the screws and washers. Orient the spout to the inside of the bath.
If your faucet is not available at this time, make sure the base is positioned so the faucet will properly run water into the bath.
Mark the mounting hole locations on the wooden support.
Mark the orientation of the base and where the notch is positioned on the wooden support.
1240535-2-D |
6 |
Kohler Co. |
Screw
Washer
Floor Joist
Base
3/16" Mounting Hole
Wood Support
3. Install the Base
If attached, remove the faucet from the base.
Drill 1-1/2″ (380 mm) deep holes with a 3/16″ drill bit (provided) using the marked locations as the center point.
If using concrete as the floor support, drill 1-1/2″ (380 mm) deep holes with a 3/16″ masonry bit (not provided).
Realign the base to the position you marked. Make sure the cold supply side notch is in the correct orientation.
Secure the base to the support with the screws and washers provided.
Verify the base is level and tighten the screws.
Kohler Co. |
7 |
1240535-2-D |
Guard
Hot |
Plug |
Screw |
|
Supply
Base
Blue Mark
Cold Supply
Notch
4. Connect the Supplies
NOTE: The base has a blue mark and a notch on the cold supply side.
Apply sealant tape on the ½″ NPT hot and cold supply pipes and thread into the base.
Insert the plug into the base.
Turn on the water supply and check for leaks.
Turn off the water supply.
Secure the guard onto the base with the screws provided.
1240535-2-D |
8 |
Kohler Co. |
Fit the finished floor between the
Min and Max lines.
Guard |
|
|
Finished Floor |
Ø 3" |
|
(76 mm) |
||
|
5. Install the Finished Floor
Finish the floor leaving a 3″ (76 mm) diameter hole for the guard.
Cut the guard so it is flush with the finished flooring.
Kohler Co. |
9 |
1240535-2-D |
Plug
O-Rings
Base |
Escutcheon |
|
|
||
|
Screw |
|
Hex |
Washer |
|
Wrench |
||
|
||
|
Flange |
6. Install the Faucet
NOTICE: To avoid damage to the O-rings on the bottom of the faucet, keep the faucet vertical and use care when installing the faucet.
Make sure the water is turned off.
Relieve the water pressure.
Remove the plug from the base.
Remove the rubber protector (not shown) from the faucet.
Place the faucet onto the base and insert the screws and washers provided through the flange.
Tighten the screws using the hex wrench provided.
Slide the escutcheon down onto the floor, covering the base.
1240535-2-D |
10 |
Kohler Co. |
Handshower
Holder
Diverter
|
Washer |
K-T97332-4 |
|
|
Diverter |
Hose |
|
Handshower |
|
|
Holder |
|
|
Washer |
Hose
7. Install the Handshower
Install the handshower hose as shown.
Kohler Co. |
11 |
1240535-2-D |
Handshower
Handshower
Holder
Aerator
Washer
Washer |
Handle |
Insert
Hose
Aerator
Handshower
Diverter
8. Installation Checkout
Ensure the faucet handle is in the OFF position.
Remove the aerator from the spout.
Turn on the water supply and check for leaks.
Point the hose into the bath and turn the faucet handle to the ON position.
Pull the diverter out to send water through the hose to remove debris.
Turn the faucet off to reset the diverter.
Turn the faucet on and run hot and cold water through the spout to remove debris.
Check for leaks.
Turn the faucet off.
Reinstall the aerator and install the handshower to the hose. Place the handshower into the handshower holder.
1240535-2-D |
12 |
Kohler Co. |
Care and Cleaning
For best results, keep the following in mind when caring for your KOHLER product:
•Use a mild detergent such as liquid dishwashing soap and warm water for cleaning. Do not use abrasive cleaners that may scratch or dull the surface.
•Carefully read the cleaner product label to ensure the cleaner is safe for use on the material.
•Always test your cleaning solution on an inconspicuous area before applying to the entire surface.
•Do not allow cleaners to sit or soak on the surface.
•Wipe surfaces clean and rinse completely with water immediately after cleaner application. Rinse and dry any overspray that lands on nearby surfaces.
•Use a soft, dampened sponge or cloth. Never use an abrasive material such as a brush or scouring pad to clean surfaces.
For detailed cleaning information and products to consider, visit www.kohler.com/clean. To order Care & Cleaning information, call 1-800-456-4537.
Warranty
KOHLER® Faucet Lifetime Limited Warranty
Kohler Co. warrants its Faucets* manufactured after January 1, 1997, to be leak and drip free during normal residential use for as long as the original consumer purchaser owns his or her home. If the Faucet should leak or drip during normal use, Kohler Co. will, free of charge, mail to the purchaser the cartridge necessary to put the Faucet in good working condition. This warranty applies only to Kohler Faucets installed in the United States of America, Canada or Mexico (″North America″).
Kohler Co. also warrants all other aspects of the faucet or accessories (″Faucet″)*, (except gold, non-Vibrant®, non-chrome finishes) to be free of defects in material and workmanship during normal residential use for as long as the original consumer purchaser owns his or her home. This warranty applies only to Kohler Faucets installed in North America. If a defect is found in normal residential use, Kohler Co. will, at its election, repair, provide a replacement part or product, or make appropriate adjustment. Damage to a product caused by accident, misuse, or abuse is not covered by this warranty. Improper care and
Kohler Co. |
13 |
1240535-2-D |
Warranty (cont.)
cleaning will void the warranty**. Proof of purchase (original sales receipt) must be provided to Kohler Co. with all warranty claims. Kohler Co. is not responsible for labor charges, installation, or other incidental or consequential costs. In no event shall the liability of Kohler Co. exceed the purchase price of the Faucet.
If the Faucet is used commercially or is installed outside of North America, or if the finish is gold, non-Vibrant or a painted or powder coated color finish, Kohler Co. warrants the Faucet to be free from defects in material and workmanship for one (1) year from the date the product is installed, under Kohler Co.’s standard one-year limited warranty.
If you believe that you have a warranty claim, contact Kohler Co., either through your Dealer, Plumbing Contractor, Home Center or E-tailer, or by writing Kohler Co., Attn.: Customer Care Center, 444 Highland Drive, Kohler, WI 53044, USA. Please be sure to provide all pertinent information regarding your claim, including a complete description of the problem, the product, model number, color, finish, the date the product was purchased and from whom the product was purchased. Also include your original invoice. For other information, or to obtain the name and address of the service and repair facility nearest you, call 1-800-4-KOHLER (1-800-456-4537) from within the USA and Canada, and 001-800-456-4537 from within Mexico, or visit www.kohler.com within the USA, www.ca.kohler.com from within Canada, or www.mx.kohler.com in Mexico.
KOHLER CO. AND/OR SELLER ARE PROVIDING THESE WARRANTIES IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. KOHLER CO. AND/OR SELLER DISCLAIM ALL LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states/provinces do not allow limitations of how long an implied warranty lasts or the exclusion or limitation of such damages, so these limitations and exclusions may not apply to you. This warranty gives the consumer specific legal rights. You may also have other rights that vary from state/province to state/province.
This is Kohler Co.’s exclusive written warranty.
*Trend® faucets, MasterShower® tower, BodySpa systems and components; WaterHaven® tower, systems and components; Tripoint® faucets, Polished Gold, non-Vibrant and painted or powder coated finishes, fittings; all items within the ″Fixture Related″ section of the Kohler Faucets Price Book, drains, Duostrainer® sink strainers,
1240535-2-D |
14 |
Kohler Co. |
Loading...