GPSMAP® 3206/3210 & GPS 17
installation instructions
© Copyright 2006 Garmin Ltd. or its subsidiaries |
|
|
Garmin International, Inc. |
Garmin (Europe) Ltd. |
Garmin Corporation |
1200 East 151st Street, |
Unit 5, The Quadrangle, |
No. 68, Jangshu 2nd Road, |
Olathe, Kansas 66062, U.S.A. |
Abbey Park Industrial Estate, |
Shijr, Taipei County, Taiwan |
Tel. 913/397.8200 or 800/800.1020 |
Romsey, SO51 9DL, U.K. |
Tel. 886/2.2642.9199 |
Fax 913/397.8282 |
Tel. 44/0870.8501241 |
Fax 886/2.2642.9099 |
|
Fax 44/0870.8501251 |
|
All rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded, or stored in any storage medium, for any purpose without the express prior written consent of Garmin. Garmin hereby grants permission to download a single copy of this manual onto a hard drive or other electronic storage medium to be viewed and to print one copy of this manual or of any revision hereto, provided that such electronic or printed copy of this manual must contain the complete text of this copyright notice and provided further that any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.
Information in this document is subject to change without notice. Garmin reserves the right to change or improve its products and to make changes in the content without obligation to notify any person or organization of such changes or improvements. Visit the Garmin Web site (www.garmin.com) for current updates and supplemental information concerning the use and operation of this and other Garmin products.
Garmin® is a registered trademark of Garmin Ltd. or its subsidiaries and may not be used without the express permission of Garmin.
Safety Information
WARNING: This product, its packaging, and its components contain chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. This Notice is being provided in accordance with California’s Proposition 65. If you have any questions or would like additional information, please refer to our Web site at http://www.garmin.com/prop65.
Limited Warranty
This Garmin product is warranted to be free from defects in materials or workmanship for one year from the date of purchase. Within this period, Garmin will at its sole option repair or replace any components that fail in normal use. Such repairs or replacement will be made at no charge to the customer for parts or labor, provided that the customer shall be responsible for any transportation cost. This warranty does not cover failures due to installation errors, abuse, misuse, accident, or unauthorized alteration or repairs.
THE WARRANTIESAND REMEDIES CONTAINED HEREINARE EXCLUSIVEAND IN LIEU OFALL OTHER WARRANTIES EXPRESS OR IMPLIED OR STATUTORY, INCLUDINGANY LIABILITYARISING UNDERANYWARRANTY OF MERCHANTABILITY OR FITNESS FORAPARTICULAR PURPOSE, STATUTORY OR OTHERWISE. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH MAYVARY FROM STATE TO STATE.
IN NO EVENT SHALL GARMIN BE LIABLE FORANY INCIDENTAL, SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, WHETHER RESULTING FROM THE USE, MISUSE, OR INABILITYTO USE THIS PRODUCT OR FROM DEFECTS IN THE PRODUCT. Some states do not allow the exclusion of incidental or consequential damages, so the above limitations may not apply to you.
Garmin retains the exclusive right to repair or replace the product or offer a full refund of the purchase price at its sole discretion. SUCH REMEDYSHALL BE YOUR SOLEAND EXCLUSIVE REMEDY FORANY BREACH OF WARRANTY.
OnlineAuction Purchases: Products sold through online auctions are not eligible for rebates or other special offers from Garmin. Online auction confirmations are not accepted for warranty verification. To obtain warranty service, an original or copy of the sales receipt from the original retailer is required. Garmin will not replace missing components from any package purchased through an online auction.
International Purchases:Aseparate warranty is provided by international distributors for units purchased outside the United States. This warranty is provided by the local in-country distributor and this distributor provides local service for your unit. Distributor warranties are only valid in the area of intended distribution. Units purchased in the United States or Canada must be returned to the Garmin service center in the United Kingdom, the United States, Canada, or Taiwan for service.
To obtain warranty service, contact your local Garmin authorized dealer or call Garmin Product Support for shipping instructions and an RMAtracking number. The product should be securely packed with the tracking number clearly written on the outside of the package. The product should then be sent, freight charges prepaid, to any Garmin warranty service station.Acopy of the original sales receipt is required as the proof of purchase for warranty repairs.
June 2006 |
190-00593-02 Rev. B |
Printed in Taiwan |
INTRODUCTION
INTRODUCTION
The GPSMAP 3206/3210 Multi-Function Display (MFD) and GPS 17 must be properly installed according to the following instructions for the best possible performance. To complete the installation, you need the appropriate fasteners, tools, and mounts listed in each section. These items are available at most marine dealers.Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding.
When drilling or cutting, always check first to see what is on the opposite side of the surface. Mount the GPSMAP 3206/3210 in a location that provides a clear, glare-free view of the display and easy operation of the controls. If you experience difficulty installing the unit, contact
Garmin Product Support or seek the assistance of a professional installer.
Mounting knob
Bail mount
Mounting holes
GPSMAP 3206 Shown
GPSMAP 3206/3210 & GPS 17 |
1 |
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
Surface Mounting the GPSMAP 3206/3210
Tools
•Drill and drill bit
•Screwdriver
•Pencil
•Mounting hardware (not included)
NOTE: Mounting hardware (fasteners) not included. Mounting holes are 5/16" (7.9 mm) in diameter.
To install the bail mount and unit:
1.Using the bail mount as a template, mark the location of the four mounting holes. Leave at least two inches of clearance behind the unit for the wiring.
2.Using an appropriate size drill bit, drill pilot holes for the fasteners.
3. Secure the bail mount to the surface with the fasteners. 4. Loosen the mounting knobs.
5. Slide the unit into the bail mount, and tighten the mounting knobs.
Bail Mount
Mounting knobs
RANGE
PAGE
QUIT
ENTER
MARK
|
ADJ |
NAV |
|
MENU |
|
|
|
MOB |
DATA |
|
|
CNFG |
FCTN |
|
|
FIND |
|
|
|
|
1 |
ABC |
DEF |
2 |
3 |
|
GHI |
JKL |
MNO |
4 |
5 |
6 |
PQRS |
TUV |
WXYZ |
7 |
8 |
9 |
|
+0- |
|
Bail mount
2 |
GPSMAP 3206/3210 & GPS 17 |
Flush Mounting the GPSMAP 3206/3210
Tools
•Flush Mount Template
•Jig saw
•Masking tape
•Scissors
•Drill
•Drill bits—1/8" (3 mm) and 3/8" (6 mm)
•1/16" (2 mm)Allen (Hex) wrench
•Sockets or wrenches
•Hammer
•Center punch
INSTALLATION INSTRUCTIONS
RANGE
PAGE
QUIT
ENTER
MARK
|
ADJ |
NAV |
|
MENU |
|
|
|
MOB |
DATA |
|
|
CNFG |
FCTN |
|
|
FIND |
|
|
|
|
1 |
ABC |
DEF |
2 |
3 |
|
GHI |
JKL |
MNO |
4 |
5 |
6 |
PQRS |
TUV |
WXYZ |
7 |
8 |
9 |
|
+0- |
|
Flush Mount
To flush mount the GPSMAP 3206/3210:
1.Trim the Flush Mount Template, and tape it in the location you want.
2.Using the center punch, indent the center of each mounting hole location.
3.Using a 1/8" (3 mm) drill bit, drill the four mounting holes.
4.Using a 3/8" (6 mm) drill bit, drill a hole to begin cutting the mounting surface.
5.Using the jig saw, cut the mounting surface along the inside of the dashed line indicated on the template. Use a file and sandpaper to refine the size of the hole. Be very careful when cutting this hole. There is only a small amount of clearance between the case molding and the mounting holes.
6.Install the four mounting studs into the unit by screwing the shorter, threaded section into the back of the unit. Use a 1/16" (2 mm) Allen wrench to tighten the mounting studs until the stop contacts the case. Be careful not to overtighten, because this may damage the mounting stud! The studs have a reusable thread-locking patch pre-applied from the factory.
7.Place the unit into the cut-out of the mounting surface.
8.Place washers over the mounting studs, then thread on one hex nut per mounting stud. Tighten all four until the unit is snug
against the mounting surface. Install and tighten the second hex nut set on all four mounting studs to lock the first set in place.
|
|
|
TRIM TEMPLATE ALONG THIS LINE TO AID FITTING |
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
9.05" (230 mm) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
GPSMAP 2010/2010C/3010C/3210 |
|
|
|
|||
CUT MOUNTING SURFACE |
|
|
|
|
|
|
|
|
ALONG INSIDE OF THIS LINE. |
|
|
|
|
|
|
|
|
Be very careful when cutting this hole, |
|
|
|
|
|
|
|
|
because there is only a small amount of |
|
|
|
|
|
|
|
|
clearance between the unit and the |
To flush mount the GPSMAP 2010/2010C/3010C/3210: |
|
|
|
||||
mounting hole. |
|
|
|
|||||
|
|
1. |
Trim the flush mount template and tape in the desired location. |
|
|
|
||
|
|
2. |
Using the center punch, indent the center of each mounting hole location. |
|
|
|
||
|
|
3. |
Using an 1/8" (3 mm) drill bit, drill the four mounting holes. (Drilling the mounting |
|
|
|
||
|
|
|
holes before cutting the hole for the unit allows for an easier installation.) |
|
|
|
||
UNIT OUTLINE |
4. Using a 3/8" (6 mm) drill bit, drill a hole to begin cutting the mounting surface. |
|
|
|
||||
|
|
5. |
Using the jig saw, cut the mounting surface along the inside of the dashed line |
8.19" |
||||
|
|
|
indicated on the template. Be very careful when cutting this hole, because there is only a |
(208 mm) |
||||
|
|
|
small amount of clearance between the case molding and the mounting holes. |
|
|
|
||
|
|
6. |
Install the four mounting studs into unit by screwing the shorter, threaded section |
|
|
|
||
|
|
|
into the back of the unit. Use a 1/16" (2 mm) Allen wrench to tighten the mounting studs |
|
|
|
||
|
|
|
until the stop contacts the case. Be careful not to overtighten, because this may damage the |
|
|
|
||
|
|
|
mounting stud! The studs have a reusable thread-locking patch pre-applied from the factory. |
|
|
|
||
|
|
7. |
Place the unit into the cut out of the mounting surface. |
|
|
|
||
|
|
8. |
Place washers over the mounting studs, and then thread on one hex nut per mounting stud. |
|
|
|
||
|
|
|
Tighten all four until the unit is snug against the mounting surface. |
|
|
|
||
|
|
|
Install and tighten the second hex nut on all four mounting studs to lock the first one |
|
|
|
||
|
|
|
in place. |
|
|
|
||
Drill a 3/8" (6 mm) hole. |
|
|
|
|
|
|
|
|
Begin cutting here. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Stud |
Washer Hex nuts |
Mounting surface |
|
|||
Flush Mount Template |
|
|
|
GPSMAP 3206/3210 & GPS 17 |
3 |
INSTALLATION INSTRUCTIONS
Installing the GPS 17
The GPS 17 can be flush mounted or installed on any standard 1" O.D. (Outer Dimension), 14 threads-per-inch marine mount. When mounting the GPS 17, the cable can be run externally, through the mounting panel, or through the center of the marine mount.
The GPS 17 connects to the 18-pin Power/Data cable on the GPSMAP3206/3210 and provides the GPS/WAAS signal for the unit. If two or more GPSMAP 3205/3206/3210 units are installed and networked, only one GPS 17 needs to be installed.
To ensure the best reception, mount the GPS 17 in a location that has a clear, unobstructed view of the sky in all directions.Avoid mounting the GPS 17 where it is shaded by the boat’s superstructure, a radome antenna, or mast. Sailboat users should avoid mounting the unit high on the mast to prevent inaccurate speed readings caused by excessive heeling. The unit provides more stable readings if it is located nearer to water level. Mount the GPS 17 at least 3 ft away from
(preferably above) the path of any radar beam or a VHFradio antenna.
Temporarily secure the unit in the preferred mounting location, and test for correct operation. With correct operation verified, permanently mount the unit. If interference with other electronics is experienced, try a different location.
NOTE: Never paint the GPS 17 or clean it with harsh solvents.
To flush mount the GPS 17:
ABOVE - BEST
Radar |
|
BELOW - OK |
3' |
|
Radar VHF Radio Antenna
NOTE: Mount the antenna at least 3 ft away from (preferably above) the path of any radar beam or a VHF radio antenna.
BETTER
BEST
GOOD
SSJAYHAWK
EMI
EMI (Electromagnetic Interference)
from engine components
Signal Interference
1.Cut out the Flush Mount Drilling Template provided on page 15, and tape it on the selected mounting location.
2.Mark the center of each mounting hole by tapping the end of a center punch or pointed object with a hammer. If the cable is going to be installed through the mounting panel, mark the center of the additional hole.
3.Drill the holes using the appropriate drill bits.
4.Align the GPS 17 over the mounting holes, and fasten it using M4 screws. The mounting threads in the GPS 17 are 8.10 mm deep. Do not use screws that thread into the GPS 17 deeper than 8 mm, or the case may be damaged.
The GPS 17 can be installed with the coax through the panel |
|
or on the outside of the unit. If the coax is run through the |
Mounting holes |
panel, seal the outside exit area with marine sealant. |
Bottom of GPS 17
4 |
GPSMAP 3206/3210 & GPS 17 |
Loading...