Epson EMP-822H User Manual

1

User's Guide

Notations Used in This Guide	2

fSafety Indications

So that you can use the projector safely and correctly, symbols are applied in the documentation and on the projector to indicate possible harm to the user or to others and the risk of damage to property.

The indications and their meaning are as follows. Make sure you understand them properly before reading the guide.

		Warning			Indicates the possibility of death or serious injury if this symbol is ignored or if sufficient care is not taken.
		Caution			Indicates the possibility of injury or damage to property if this symbol is ignored or if sufficient care is not taken.
f General Information Indications
		Attention			Indicates procedures which may result in damage or injury if sufficient care is not taken.
		q			Indicates additional information and points which may be useful to know regarding a topic.
		s			Indicates a page where detailed information regarding a topic can be found.
			g		Indicates that an explanation of the underlined word or words in front of this symbol appears in the glossary of terms. See
					the "Glossary" section of the "Appendices". s p.65
					Indicates operating methods and the order of operations.
		Procedure
					The procedure indicated should be carried out in the order of the numbered steps.
		[ (Name) ]			Indicates the name of the buttons on the remote control or the control panel.
					Example: [Esc] button
		"(Menu Name)"			Indicates configuration menu items.
					Example: "Image" - "Brightness"
					Indicates that the explanation continues on the following page. Clicking this symbol will display the following page.
					Indicates that the explanation is continued from the previous page. Clicking this symbol will display the previous page.

Contents	3

Projector Features......................................................................................	4
Part Names and Functions ........................................................................	5
Front/Top..............................................................................................................	5
Rear (EMP-83H/822H Only) ................................................................................	6
Rear (EMP-X5/S5 Only).......................................................................................	7
Control Panel .......................................................................................................	8
Remote Control ..................................................................................................	10
Base ...................................................................................................................	11
Useful Functions
Changing the Projected Image (Source Search) ...................................	13
Functions for Enhancing Projection.......................................................	14
Selecting the Projection Quality (Selecting Color Mode) ...................................	14
Hiding the Image and Sound Temporarily (A/V Mute) .......................................	15
Freezing the Image (Freeze)..............................................................................	16
Changing the Aspect Ratio (Aspect) ..................................................................	16
Enlarging Part of the Image (E-Zoom) ...............................................................	17
Security Functions ...................................................................................	18
Managing Users (Password Protect) .................................................................	18
Restricting Operation (Operation Lock)..............................................................	20
Anti-Theft Lock ...................................................................................................	21
Configuration Menu
Using the Configuration Menu ................................................................	23
List of Functions.......................................................................................	24
Image Menu (EMP-83H/822H Only) ..................................................................	24
Image Menu (EMP-X5/S5 Only).........................................................................	25
Signal Menu (EMP-83H/822H Only) ..................................................................	26
Signal Menu (EMP-X5/S5 Only).........................................................................	27
Settings Menu ....................................................................................................	28
Extended Menu..................................................................................................	29
Network Menu (EMP-83H/822H Only) ...............................................................	31
Info Menu (Display Only)....................................................................................	34
Reset Menu........................................................................................................	35
Troubleshooting
Using the Help ..........................................................................................	37
Problem Solving .......................................................................................	38
Reading the Indicators .......................................................................................	38
When the Indicators Provide No Help ................................................................	41

Appendices
Installation Methods ................................................................................	49
Cleaning ....................................................................................................	50
Cleaning the Projector's Surface .......................................................................	50
Cleaning the Lens..............................................................................................	50
Cleaning the Air Filter and Air Intake Vent.........................................................	50
Replacing Consumables .........................................................................	51
Replacing the Remote Control Batteries ...........................................................	51
Replacing the Lamp...........................................................................................	52
Replacing the Air Filter ......................................................................................	56
Saving a User's Logo...............................................................................	57
Screen Size and Distance........................................................................	59
EMP-83H/822H/X5 ............................................................................................	59
EMP-S5 .............................................................................................................	60
Connecting to External Equipment ........................................................	61
Connecting to an External Monitor ....................................................................	61
Connecting to External Speakers (EMP-83H/822H Only) .................................	61
Connecting a LAN Cable (EMP-83H/822H Only)....................................	62
Connecting a USB Cable (EMP-X5/S5 Only)..........................................	63
Optional Accessories and Consumables ..............................................	64
Glossary....................................................................................................	65
ESC/VP21 Commands .............................................................................	67
Command List....................................................................................................	67
Cable Layouts....................................................................................................	67
Connecting a USB (EMP-X5/S5 Only)...............................................................	68
USB Connection Setup......................................................................................	68
PJLink (EMP-83H/822H Only)..................................................................	69
List of Supported Monitor Displays .......................................................	70
Specifications...........................................................................................	71
Appearance...............................................................................................	75
Index..........................................................................................................	76

Projector Features

Ease of use

f The A/V mute slide makes it easy to project and store

You can stop and resume projection easily by opening and closing the A/V mute slide which makes giving clear presentations easier.

f A single foot design means you do not have to make any difficult levelling adjustments

You can easily make height

adjustments with one hand. sQuick Start Guide

4

Enhanced security functions

f Password Protect to restrict and manage users

By setting a password you can restrict who can use the projector. s p.18

f Operation Lock restricts button operation on the control panel

You can use this to prevent people from changing projector settings without permission at events, in schools, and so on. s p.20

f Equipped with various anti-theft devices

The projector is equipped with the following security devices. s p.21

•Security slot

•Security cable installation point

Easy to handle

f Direct power On/Off (EMP-83H/822H only)

In places where power is managed centrally, such as in a conference room, the projector can be set to power on and off automatically when the power source to which the projector is connected is switched on or off.

f No cool down delay

After turning the projector's power off, you can disconnect the projector's power cable without having to wait for the projector to cool down first.

Part Names and Functions

Front/Top

	K
A	J
B	I
C	H
	G
	F
	E
	D
Name	Function
A Control panel	s p.8
B Lamp cover	Open this cover when replacing the projector's
	lamp. s p.53
C Air exhaust vent	Caution
	Do not place objects that may become warped
	or otherwise affected by heat near the air
	exhaust vent and do not put your face or
	hands near the air exhaust vent while
	projection is in progress.

5

	Name	Function
D	Front adjustable	Extend and adjust the position of the projected
	feet	image when the projector is placed on a
		surface such as a desk. s Quick Start Guide
E	Foot adjust lever	Pull out the foot lever to extend and retract the
		front foot. s Quick Start Guide
F	A/V mute slide	Slide shut when not using the projector to
		protect the lens. By closing during projection
		you can hide the image and the sound (A/V
		Mute). s Quick Start Guide, p.15
G	Remote receiver	Receives signals from the remote control.
		s Quick Start Guide
H	Focus ring	Adjusts the image focus. s Quick Start Guide
I	Zoom ring	Adjusts the image size. s Quick Start Guide
	(EMP-83H/822H/
	X5 only)
J	A/V mute slide	Slide the knob to open and close the A/V mute
	knob	slide.
K	Security slot (j)	The security slot is compatible with the
		Microsaver Security System manufactured by
		Kensington. s p.21

Part Names and Functions

Rear (EMP-83H/822H Only)

A H G F

B C

D E

Name

Function

A

Remote receiver

Receives signals from the remote control.

s Quick Start Guide

B

Speaker

C

Monitor Out port

Outputs the image signal from the computer

connected to the Computer1 input port to an

external monitor. This is not available for

component videog signals or other signals

being input to any port other than the

Computer1 input port.s p.61

Audio Out port

Outputs the sound of the image currently being

projected to external speakers. s p.61

D Power inlet

Connects to the power cable.

s Quick Start Guide

6

	Name	Function
E	RS-232C port	When controlling the projector from a
		computer, connect it to the computer with an
		RS-232C cable. This port is for control use and
		should not normally be used. s p.67
F	Computer1 input	For video signals from a computer and
	port	component videog signals from other video
		sources.
	Audio1 input port	Connect to the audio out port of the computer
		connected to the Computer1 input port.
	Computer2 input	For video signals from a computer and
	port	component videog signals from other video
		sources.
	Audio2 input port	Connect to the audio out port of the computer
		connected to the Computer2 input port.
		s Quick Start Guide
G S-Video input		For S-videog signals from video sources.
	port
	Video input port	For composite videog signals from video
		sources.
	Audio-L/R input	Connects to the audio out port of the
	port	equipment connected to the S-Video port or
		Video input port. s Quick Start Guide
H LAN port		When a LAN cable is connected, you can
		monitor and control the projector over a LAN.
		s p.62

Part Names and Functions

Rear (EMP-X5/S5 Only)

A I H G F E D

B

C

Name

Function

A

Remote receiver

Receives signals from the remote control.

s Quick Start Guide

B

Speaker

C

Power inlet

Connects to the power cable.

s Quick Start Guide

D

Monitor Out port

Outputs the image signal from the computer

connected to the Computer input port to an

external monitor. This is not available for

component videog signals or other signals

being input to any port other than the

Computer input port.s p.61

7

	Name	Function
E	Computer input	For video signals from a computer and
	port	component videog signals from other video
		sources.
F	Audio-L/R input	Connects to the audio output port for the
	port	equipment you want to project from and inputs
		the audio. s Quick Start Guide
G	Video input port	For composite videog signals from video
		sources.
H	S-Video input	For S-videog signals from video sources.
	port
I	USB port (Type B)	When showing a slide show in PowerPoint,
		you can use the projector's remote control to
		move to the next slide/previous slide if it is
		connected to a computer by a USB cable.*
		Also, you can use it as a control port when the
		projector is controlled by a computer.
		Even if the projector is connected to a
		computer by a USB cable, you cannot project
		the image on the computer. s p.63

*Limited to computers with the following operating systems installed. Windows 98/98SE/2000/Me/XP Home Edition/XP Professional Macintosh: OS 8.6 to 9.2/10.1 to 10.3

Part Names and Functions

Control Panel

f EMP-83H/822H/X5

A I H G

B C D E F

fEMP-S5

Buttons without numbers operate in the same way as in the figure above. See the numbers in the table for the figure above.

J

8

	Name	Function
A	[Power] button	Turns the projector power on or off.
		s Quick Start Guide
B	Status indicators	The color of the indicators and whether they
		are flashing or lit indicates the status of the
		projector. s p.38
C	[Source Search]	Changes to the next input source that is
	button	connected to the projector and is sending an
		image.s p.13
D	[Enter] button	If pressed during projection of computer signal
		images, it automatically adjusts the tracking,
		synchronization, and position to project the
		optimum image.
		When a configuration menu or a help screen is
		displayed, it accepts and enters the current
		selection and moves to the next level.s p.23
E [v] [w] buttons		Corrects keystone distortion.
		If pressed when a configuration menu or a help
		screen is displayed, these buttons select menu
		items and setting values.
		s Quick Start Guide, p.23
F	[Help] button	Displays and closes the help screen which
		shows you how to deal with problems if they
		occur.s p.37
G	[Esc] button	Stops the current function.
		If pressed when a configuration menu is
		displayed, it moves to the previous menu
		level.s p.23

H [a] [b] buttons

(EMP-83H/822H/ X5 only)

Press to adjust the volume.

If pressed when a configuration menu or a help screen is displayed, these buttons select menu items and setting values.

s Quick Start Guide, p.23

Part Names and Functions	9

Name	Function
I [Menu] button	Displays and closes the configuration
	menu.s p.23

J [Wide] [Tele] buttons (EMP-S5 only)

Adjusts the image size.

If pressed when a configuration menu or a help screen is displayed, these buttons select menu items and setting values.

s Quick Start Guide, p.23

Part Names and Functions

Remote Control

		P
	A	O
		N
	B
		M
	C
		L
	D	K
	E	J

	F	I
		H
	G

		Illustrations show EMP-X5/S5.
	Name	Function
A	[Power] button	Turns the projector power on or off.
		s Quick Start Guide
B	[Source Search]	Changes to the next input source that is
	button	connected to the projector and is sending an
		image.s p.13

			10
	Name	Function
C	[Menu] button	Displays and closes the configuration menu.
		s p.23
D	[Enter/Auto]	If pressed during projection of computer signal
	button	images, it automatically adjusts the tracking,
		synchronization, and position to project the
		optimum image. s p.26
		When a configuration menu or a help screen is
		displayed, it accepts and enters the current
		selection and moves to the next level.s p.23
E	[Color Mode]	Each time the button is pressed, the color
	button	mode changes.s p.14
F	[Page] button	When showing a slide show in PowerPoint,
	(Down) (Up)	you can use the projector's remote control to
	(EMP-X5/S5 only)	move to the next slide/previous slide if it is
		connected to a computer by a USB cable.*
		s p.63
G	[E-Zoom] button	(+) Enlarges the image without changing the
	(+) (-)	projection size.
		(-) Reduces parts of the image that have been
		enlarged using the [+] button.s p.17
H	[A/V Mute] button	Turns the video and audio on or off. s p.15
I [Freeze] button		Images are paused or unpaused.s p.16
J	[Aspect] button	The aspect ratiog changes each time the
		button is pressed.s p.16
K Numeric buttons		Use these buttons when entering a password.

sp.19

*Limited to computers with the following operating systems installed. Windows 98/98SE/2000/Me/XP Home Edition/XP Professional Macintosh: OS 8.6 to 9.2/10.1 to 10.3

Part Names and Functions

Name	Function

L [Volume -] button

[Volume +] button

Press [Volume -] to lower the volume and press [Volume +] to raise the volume.

If pressed when a configuration menu or a help screen is displayed, these buttons select menu items and setting values.

s Quick Start Guide , p.23

M [Esc] button Stops the current function. If pressed when a configuration menu is displayed, it moves to the previous level. s p.23

N [Help] button Displays and closes the help screen which shows you how to deal with problems if they occur.s p.37

O [u] [d] buttons If pressed when a configuration menu or a help screen is displayed, these buttons select menu items and setting values. s p.23

P Remote control Outputs remote control signals.

light-emitting s Quick Start Guide area

11

Base

D

A

B

C	B

	Name	Function
A	Suspension	Attach the optional ceiling mount here when
	bracket fixing	suspending the projector from a ceiling.
	points (3 points)	s p.49, 64
B	Rear foot	Turn to extend and retract to adjust the
	(2 points)	horizontal tilt. s Quick Start Guide
C	Security cable	Pass a commercially available anti-theft wire
	installation point	lock through here when you want to secure the
		projector to a fixed object. s p.21
D	Air filter (Air	This prevents dust and other foreign particles
	intake vent)	from getting inside the projector when air is
		drawn in. The projector displays a warning
		message when it is time to clean or replace the
		air filter.s p.50, 56

Useful Functions

This chapter explains useful functions for giving presentations and so on, and the security functions.

Changing the Projected Image
(Source Search) ..................................................	13
Functions for Enhancing Projection.................	14
• Selecting the Projection Quality
(Selecting Color Mode) .....................................................	14
• Hiding the Image and Sound Temporarily
(A/V Mute) .........................................................................	15
• Freezing the Image (Freeze).............................................	16
• Changing the Aspect Ratio (Aspect)................................	16
• Enlarging Part of the Image (E-Zoom) ...........................	17

Security Functions..............................................	18
• Managing Users (Password Protect)...............................	18
Type of Password Protect ..............................................................	18
Setting Password Protect................................................................	19
Entering the Password....................................................................	20
• Restricting Operation (Operation Lock)........................	20
• Anti-Theft Lock ................................................................	21
Installing the wire lock...................................................................	21

Changing the Projected Image (Source Search)	13

The projector automatically detects signals being input from connected equipment, and the image being input from the equipment is projected.

You can project the target image quickly because it skips input ports where no image is being input.

Computer1

Computer2*

S-Video

Video

The input port where no image signal is being input is skipped.

* EMP-83H/822H only

Procedure

When your video equipment is connected, start playback before beginning this operation.

Using the remote control

Using the control panel

When two or more pieces of equipment are connected, press the [Source Search] button until the target image is projected.

The following screen showing the status of image signals is q displayed when only the image that the projector is

currently displaying is available, or when no image signal can be found. You can select the input port where the connected equipment you want to use is projecting. If no operation is performed after about 10 seconds, the screen closes.

For EMP-83H/822H

Functions for Enhancing Projection	14

Selecting the Projection Quality (Selecting Color

Mode)

You can easily obtain the optimum image quality simply by selecting the setting that best corresponds to your surroundings when projecting. The brightness of the image varies depending on the mode selected.

Mode	Application
Game	Ideal for use in a bright room. This is the brightest
	mode and reproduces shadow tones well.
Presentation	Ideal for making presentations using color materials
	in a bright room.
Text	Ideal for making presentations using black-and-
	white materials in a bright room.
Theatre	Ideal for watching films in a dark room. This gives
	images a natural tone.
Photo	(When computer images are input)
	Ideal for projecting still pictures, such as photos, in a
	bright room. This makes images vivid and brings
	them into contrast.
Sports	(When component video, S-video, or composite
	video images are input)
	Ideal for watching TV programmes in a bright room.
	This makes images vivid and brings them to life.
sRGBg	Ideal for images that conform to the sRGB color
	standard.
Blackboard	Even if you are projecting onto a blackboard
	(greenboard), this setting gives your images a natural
	tint, just like when projecting onto a screen.

Procedure

Remote control

Each time you press the button, the color mode name is displayed on the screen and the color mode changes.

If you press the button while the color mode name is displayed on the screen, it changes to the next color mode.

q The color mode can also be set using "Color Mode" from the "Image" menu in the configuration menu. s p.24, 25

Functions for Enhancing Projection

Hiding the Image and Sound Temporarily (A/V Mute)

You can use this when you want to focus the audience's attention on what you are saying, or if you do not want to show details such as when you are changing between files during presentations from a computer.

Procedure

Remote control

Projector

Each time you press the button, or the A/V mute slide is opened or closed, A/V Mute turns on or off.

15

• If you use this function when projecting moving images, q the images and sound continue to be played back by the

source, and you cannot return to the point where A/V Mute was activated.

•From the remote control you can choose to display black, blue, or logo* as the A/V mute display using the "Extended" - "Display" - "A/V Mute" setting in the configuration menu. s p.29

•When the A/V mute slide is closed and A/V Mute begins, the power supply can be set to automatically turn off after about 30 minutes by setting "Extended" - "Operation" - "Lens Cover Timer" in the configuration menu. s p.30

*Depending on the area of purchase, the User's Logo function may not be available for EMP-X5/S5.

Functions for Enhancing Projection	16

Freezing the Image (Freeze)

When the moving image on the screen is frozen, the image continues to project, so you can project a moving image one frame at a time like a still photo. Also, you can perform operations such as changing between files during presentations from a computer without projecting any images if the Freeze function is activated beforehand.

Procedure

Remote control

Each time you press the button, Freeze turns on or off.

q	• Audio does not stop.
	• The image source continues to play back the moving
	images even while the screen is frozen, so it is not possible
	to resume projection from the point where it was paused.
	• If the [Freeze] button is pressed while the configuration
	menu or a help screen is displayed, the menu or help
	screen being displayed is cleared.
	• Freeze still works while E-Zoom is being used.

Changing the Aspect Ratio (Aspect)

When video equipment is connected, images that have been recorded in digital video or onto DVDs can be viewed in 16:9 wide-screen format. You can change the aspect ratiog for images in squeeze modeg as follows.

4:3

16:9

16:9 (Up)

16:9 (Down)

Procedure

Remote control

Each time you press the button, the aspect name is displayed on the screen and the aspect changes.

Functions for Enhancing Projection

If you press the button while the aspect name is displayed on the screen, it changes to the next aspect mode.

q This can also be set using "Aspect" from the "Signal" menu in the configuration menu. s p.26

Enlarging Part of the Image (E-Zoom)

This is useful when you want to expand images such as graphs and tables to see them in greater detail.

Procedure

A Start E-Zoom.

Remote control

17

B Move the cross to the area of the image that you want to enlarge.

Remote control

Cross

C Enlarge.

Remote control

Each time the button is pressed, the area is expanded. You can expand quickly by holding the button down.

You can reduce the enlarged image by pressing the [-] button. Press the [Esc] button to cancel.

• The enlargement ratio appears on the screen. The q selected area can be enlarged to between 1 to 4 times in 25

incremental steps.

• You can scroll the image by pressing [u], [d], [l], or [r].

Security Functions

The projector has the following enhanced security functions.

•Password Protect

You can limit who can use the projector.

•Operation Lock

You can prevent people from changing the settings on the projector without permission.

•Anti-Theft Lock

The projector is equipped with various types of anti-theft security devices.

Managing Users (Password Protect)

When the Password Protect function is activated, people who do not know the password cannot use the projector to project images even if the projector power is on. Furthermore, the user's logo that is displayed when you turn on the projector cannot be changed. This acts as an anti-theft device as the projector cannot be used even if it is stolen. At the time of purchase the Password Protect function is not activated.

fType of Password Protect

The following three kinds of password protect settings can be made according to how the projector is being used.

1."Power On Protect"

When "Power On Protect" is "On", the password must be entered whenever the projector is turned on after it has been disconnected from the power supply to which it was connected the last time the password was entered. If the correct password is not entered, projection does not start.

2"User's Logo Protect"*

When "User's Logo Protect" is set to "On" the following setting changes are prohibited.

• Capturing a user's logo

18

•Settings for "Display Background", "Startup Screen", and "A/V Mute" are changed from "Display" in the configuration menu.

3"Network Protect" (EMP-83H/822H only)

When "Network Protect" is set to "On" setting changes for "Network" in the configuration menu are prohibited.

*Depending on the area of purchase, the User's Logo function may not be available for EMP-X5/S5. In that case, "User's Logo Protect" is not displayed.

Security Functions

fSetting Password Protect

Use the following procedure to set Password Protect.

Procedure

A Holdseconds.down the [Freeze] button for about five

The password protect setting menu is displayed.

Remote control

• If Password Protect is already activated, you must enter q theIf thepassword.password is entered correctly, the password protect

setting menu is displayed.

s "Entering the Password" p.20

•When the password is set, stick the password protect sticker in a visible position on the projector as a further theft deterrent.

B Turn on "Power On Protect".

(1)Select "Power On Protect", and then press the [Enter] button.

(2)Select "On", and then press the [Enter] button.

(3)Press the [Esc] button.

C

D

E

19

Turn on "User's Logo Protect"*.

(1)Select "User's Logo Protect", and then press the [Enter] button.

(2)Select "On", and then press the [Enter] button.

(3)Press the [Esc] button.

Turn on "Network Protect".

(1)Select "Network Protect", and then press the [Enter] button.

(2)Select "On", and then press the [Enter] button.

(3)Press the [Esc] button.

Set the password.

(1)Select "Password", and then press the [Enter] button.

(2)When the message "Change the password?" is displayed, select "Yes" and then press the [Enter] button. The default setting for the password is "0000". Change this to your own desired password. If you select "No", the screen shown in step 1 is displayed again.

(3)Enter a four digit number using the numeric buttons. The number entered is displayed as "* * * *". When you enter the fourth digit, the confirmation screen is displayed.

Remote control

Numeric buttons

(4)Re-enter the password.

The message "Password accepted." is displayed.

If you enter the password incorrectly, a message is displayed prompting you to re-enter the password.

Security Functions

*Depending on the area of purchase, the User's Logo function may not be available for EMP-X5/S5. In that case, "User's Logo Protect" is not displayed.

fEntering the Password

When the password entry screen is displayed, enter the password using the numeric buttons on the remote control.

Procedure

Enter the password by using the numeric buttons.

When you enter the correct password, projection begins.

Attention

•If an incorrect password is entered three times in succession, the message "The projector's operation will be locked." is displayed for about five minutes, and then the projector switches to standby mode. If this happens, disconnect the power plug from the electrical outlet and then reinsert it and turn the projector's power back on. The projector displays the password entry screen again so that you can enter the correct password.

•If you have forgotten the password, make a note of the "Request Code: xxxxx" number that appears on the screen and contact the nearest address provided in the Support and Service Guide. sEpson Projector Contact List

•If you continue to repeat the above operation and input the wrong password thirty times in succession, the following message is displayed and the projector does not accept any more password entries. "The projector's operation will be locked. Contact Epson as described in your documentation." sEpson Projector Contact

List

20

Restricting Operation (Operation Lock)

Do one of the following to lock the operation buttons on the control panel.

•Full Lock

All of the buttons on the control panel are locked. You cannot perform any operations from the control panel, including turning the power on or off.

•Operation Lock

All of the buttons on the control panel, except for the [Power] button, are locked.

This is useful at events or shows when you want to deactivate all buttons and only project, or at schools when you want to limit button operation. The projector can still be operated using the remote control.

Procedure

A Press the [Menu] button and select "Settings" -

"Operation Lock" in the configuration menu. s "Using the Configuration Menu" p.23

Using the remote control

Using the control panel

Security Functions	21

Check the buttons you can use and the operations they perform in the guide under the menu.

B Select either "Full Lock" or "Operation Lock".

C Selectdisplayed."Yes" when the confirmation message is

The control panel buttons are locked according to the setting you chose.

You can release the control panel lock by one of the q following two methods.

•From the remote control, select "Off" from "Settings" - "Operation Lock" in the configuration menu.

Anti-Theft Lock

As the projector is often setup on ceiling mounts and left in rooms unattended, it is possible that someone may try and take the projector, so the projector includes the following security devices.

•Security slot

The security slot is compatible with the Microsaver Security System manufactured by Kensington. You can find details about the Microsaver Security System on the Kensington homepage http://www.kensington.com/.

•Security cable installation point

A commercially available theft-prevention wire lock can be passed through the installation point to secure the projector to a desk or pillar.

fInstalling the wire lock

Pass an anti-theft wire lock through the installation point. See the documentation supplied with the wire lock for locking instructions.

•When you press and hold down the [Enter] button on the control panel for about seven seconds, a message is displayed and the lock is released.

Configuration Menu

This chapter explains how to use the configuration menu and its functions.

Using the Configuration Menu ..........................		23
List of Functions.................................................		24
• Image Menu (EMP-83H/822H Only) ..............................		24
• Image Menu (EMP-X5/S5 Only) .....................................		25
• Signal Menu (EMP-83H/822H Only) ..............................		26
• Signal Menu (EMP-X5/S5 Only) .....................................		27
•	Settings Menu ....................................................................	28
•	Extended Menu .................................................................	29
• Network Menu (EMP-83H/822H Only) ..........................		31
• Info Menu (Display Only).................................................		34
•	Reset Menu ........................................................................	35

Using the Configuration Menu

A Selecting from the				B Selecting from the
		top menu		sub menu
			Top menu

Guide

Sub menu (Settings)

Buttons used

Using the control panel

For EMP-83H/ For EMP-S5 822H/X5

Using the remote control

23

C Changing the	D Exit
selected item

For EMP-83H/822H/X5

For EMP-S5

Select the setting to change

List of Functions	24

Image Menu (EMP-83H/822H Only)

Items that can be set vary depending on the image signal currently being projected as shown in the following screen shots. Setting details are saved for each image signal.

Computer image

Component videog/Composite videog/S-videog

Sub Menu			Function
Color Mode		You can select the quality of the image to suit your surroundings. s p.14
Brightness		You can adjust the image brightness.
Contrastg		You can adjust the difference between light and shade in the images.
Color Saturation		You can adjust the color saturation for the images.
Tint		(Adjustment is only possible when NTSC signals are being input if you use composite video/S-video.)
		You can adjust the image tint.
Sharpness		You can adjust the image sharpness.
Color Adjustment		You can make adjustments by choosing one of the following
		Abs. Color Temp.: You can adjust the overall tint of the image. You can adjust tints in 10 stages from 5000 K to 10000 K. When a high value is
		selected the image becomes tinged with blue, and when a low value is selected the image becomes tinged with red.
		Red, Green, Blue: You can adjust the saturation of each color individually.
		(This item cannot be selected if "sRGBg" is selected as the "Color Mode" setting in the "Image" menu.)
Reset		You can reset all adjustment values in the "Image" menu to their default settings. To return all menu items to their default settings, see s p.35