User’s manual
Accessory handset for use with
VTech model DS6151
w w w.v t e c h p h o n e s . c o m
Model: DS6101
BC
Congratulations
on purchasing your new VTech product. Before using this telephone, please read Important safety instructions on page 9 of this manual.
This manual has instructions for setup and registration of your new handset. For full instructions on using the handset, see the user’s manual that came with your telephone base.
If you cannot find your user’s manual, you can view or download it at www.vtechphones.com.
For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com. In Canada, please visit www.vtechcanada.com.
Compatible with
Hearing Aid T-Coil
T
TIA-1083
Telephones identified with this logo have reduced noise and interference when used with most T-coil equipped hearing aids and cochlear implants. The TIA-1083 Compliant Logo is a trademark of the Telecommunications Industry Association. Used under license.
Register online to get an additional 3-month warranty!
Visit www.vtechphones.com.
Registration
Register your product online for enhanced warranty support.
Product news
Learn about the latest VTech products.
Table of contents |
|
Getting started.................................... |
1 |
Parts checklist....................................... |
1 |
Battery installation................................ |
2 |
Battery charging.................................... |
2 |
Belt clip and optional headset.............. |
4 |
Add and register a handset................... |
5 |
Replace a handset................................ |
6 |
Handset layout...................................... |
7 |
Appendix.............................................. |
8 |
Important safety instructions................ |
9 |
Operating range.................................. |
11 |
Maintenance....................................... |
11 |
The RBRC® seal................................. |
12 |
FCC, ACTA and IC regulations........... |
13 |
California Energy Commission |
|
battery charging testing |
|
instructions...................................... |
15 |
For C-UL compliance only.................. |
16 |
Limited warranty................................. |
19 |
Technical specifications...................... |
21 |
ii
Your telephone contains the following items. Save your sales receipt and original packaging in the event warranty service is necessary.
Battery compartment cover |
Battery |
Belt clip |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Charger and power adapter |
Handset |
User’s manual |
To purchase a replacement battery or a power adapter, visit our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.
Getting started
Install the battery as shown below.
1Plug the battery connector securely into the socket inside the battery compartment, matching the color-coded label.
3Slide the battery compartment cover towards the center of the handset until it clicks into place.
2Place the battery with the label THIS SIDE UP and the wires inside the battery compartment.
4Charge the handset by placing it in the telephone base.
CHARGE light remains on when charging.
Once you have installed the battery, the screen indicates the battery status (see the table below).
•For best performance, keep the handset in the telephone base or charger when not in use.
•The battery is fully charged after 16 hours of continuous charging.
•If the handset will not be used for a long time, disconnect and remove the battery to prevent any possible leakage.
Battery indicators |
Battery status |
Action |
||||
The screen is blank. |
Battery has no charge and |
Charge without interruption |
||||
|
|
|
|
|
the handset cannot be used. |
(at least 30 minutes). |
The screen shows |
Battery has very little charge |
Charge without interruption |
||||
Place handset in |
and the handset cannot be |
(at least 30 minutes). |
||||
charger and |
|
|
flashes. |
used. |
|
|
|
|
|
|
|
|
|
The screen shows Low |
Battery has enough charge |
Charge without interruption |
||||
battery and |
|
|
flashes. |
to be used for a short time. |
(at least 30 minutes). |
|
The screen shows |
Battery is charged. |
To keep the battery charged, |
||||
HANDSET. |
|
|
|
|
place it in the telephone |
|
|
|
|
|
|
|
base when not in use. |
Getting started
Battery charging
When the battery is fully charged, you can expect the following performance:
Operation |
Operating time |
|
|
While in handset use (talking*) |
Up to 10 hours |
|
|
While in speakerphone mode (talking*) |
Up to 7 hours |
|
|
While not in use (standby**) |
Up to 10 days |
|
|
*Operating times vary depending on your actual use and the age of the battery. **Handset is not charging or in use.
Getting started
Belt clip
To attach the belt clip:
Snap the belt clip into the slots on both sides of the handset.
Headset
To remove the belt clip:
Gently lift either of the belt clip tabs outwards to remove the belt clip from the handset.
For handsfree telephone conversation, you can use any industry standard 2.5mm headset (purchased separately). For best results, use a
VTech 2.5mm headset.
Lift the plastic cover.
Plug a 2.5mm headset into the jack on the side of the handset.
Getting started
Each newly purchased handset (DS6101) must be registered to the telephone base (DS6151) before use. When first purchased, each expansion handset shows Press [HOLD] on base for 4 sec, then press [#] on handset. You may need to charge the handset before registering to the
telephone base. For more details on battery charging, see the table on page 2.
To make registration easier, read all of the instructions on this page before you begin.
To register a handset:
1.Place the unregistered handset in the telephone base. If Press [HOLD] on base for 4 sec, then press [#] on handset does not appear on the handset screen after a few seconds, remove the handset and place it in the telephone base again.
2.Press and hold HOLD on the telephone base for about four seconds until
the telephone base displays Registering handset. While the handset is still in the telephone base, press # (pound key) on the handset. The
handset shows Registering... Please wait and it takes up to 60 seconds to complete the registration. The handset and the telephone base show HANDSET X Registered (X represents the handset number assigned) and you hear a beep when the registration completes.
When the registration is complete, the newly registered handset is assigned the next available handset registration number. For instance, if you already have HANDSET, the next registered handset will be HANDSET 2. Then your first handset will be renamed as HANDSET 1.
#
HOLD
• If the registration fails, the handset shows Registration failed. To reset the handset, remove the handset from the telephone base and place it back in. Try the registration process again.
•You cannot register a handset if any other system handset is in use.
•Only one handset can be registered at a time.