VTech CS6709 User Manual

5 (2)
User’s manual
T
Compatible with
Hearing Aid T-Coil
TIA-1083
CS6709/CS6709-15/CS6709-16
DECT 6.0 accessory handset
for use with VTech models CS6719/CS6729/CS6758/CS6759/ CS6829/CS6859
Congratulations
This manual has instructions on how to set up and register your new handset. For abridged instructions on using the handset, see the Abridged user’s manual that came with your telephone base.
You may also view or download the online Complete user’s manual for a full set of installation and operation instructions at www.vtechphones.com. In Canada, visit www.vtechcanada.com.
Telephones identied with this logo have reduced noise and
interference when used with most T-coil equipped hearing aids and cochlear implants. The TIA-1083 Compliant Logo is a trademark of the Telecommunications Industry Association. Used under license.
The ENERGY STAR® program (www.energystar.gov) recognizes and encourages the use of products that save energy and help protect our environment. We are proud to mark this product with the ENERGY STAR® label indicating it meets the latest energy
efciency guidelines.
Register online to get an additional 3-month warranty!
Visit www.vtechphones.com.
Registration
Register your product online for enhanced warranty support.
Product news
Learn about the latest VTech products.
1
Parts checklist
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles : (2.4V Ni-MH) WARNING / AVERTISSEMENT : DO NOT BURN OR PUNCTURE BATTERIES. NE PAS INCINÉRER OU PERCER LES PILES. Made in China / Fabriqué en chine
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
CR1232
Your telephone package contains the following items. Save your sales receipt and original packaging in the event warranty service is necessary.
User’s manual
Handset User’s manual
Charger and charger adapter
Battery compartment cover
Battery
ECO mode
This power conserving technology reduces power consumption for optimal battery performance.
HANDSET 1
The ECO mode activates automatically whenever the handset is synchronized with the telephone base.
The handset shows ECO when the ECO mode activates.
ECO
10:15P M
12/18
ECO
Battery installation
Install the battery as shown below.
Plug the battery connector securely
1. Place the battery with the label into the socket.
2.
THIS SIDE UP facing up and the wires inside the battery compartment.
Slide the battery compartment cover
3. Place the handset in the telephone towards the center of the handset until
4. base or charger to charge.
it clicks into place.
CHARGE light remains on when charging.
If the handset will not be used for a long time, disconnect and remove the battery
• to prevent possible leakage.
To purchase a replacement battery, visit our website at www.vtechphones.com or
• call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or dial 1 (800) 267-7377.
2
Battery charging
Once you have installed the battery, the screen indicates the battery status (see the table below). For best performance, keep the handset in the telephone base or charger when not in use. The battery is fully charged after 11 hours of continuous charging.
Battery indicators Battery status Action
The screen is blank, or displays Put in charger and ashes.
The screen displays Low battery and ashes.
The screen displays HANDSET X.
If you place the handset in the telephone base or charger without plugging in the battery, the screen displays No battery.
The battery has no or very little charge. The handset cannot be used.
The battery has enough charge to be used for a short time.
The battery is charged. To keep the battery
Charge without interruption (at least 30 minutes).
Charge without interruption (about 30 minutes).
charged, place it in the telephone base or charger when not in use.
Add and register a handset
You can add new handsets (CS6709/CS6709-15/CS6709-16, purchased
separately) to your telephone system. Each handset must be registered with the telephone base before use. When rst purchased, each expansion handset displays To register HS... and ...see manual alternately. You may need to charge the handset before registering it to the telephone base.
To register a handset to a CS6719/CS6729/CS6758/CS6759/ CS6829/CS6859 base:
Place the new (non-registered) handset in the telephone base.
1.
CS6729 base CS6829 baseCS6719 base
CS6758/CS6759 base Do not place
CS6859 base
the handset in the charger.
After about 10 seconds, the handset displays Registering... When the
2.
registration process completes, the handset displays Registered and you hear a beep. The registration process takes about 90 seconds to complete.
3
Loading...
+ 5 hidden pages