Quick start guide
CS6120-2/CS6124
Introduction
This quick start guide provides you with the basic installation instructions. A limited set of features are described in abbreviated form.
Please refer to the online user’s manual for complete installation and operation instructions.
Telephone base and charger installation
Install the telephone base and charger as shown below.
Telephone wall jack |
|
|
|
Electrical outlet |
|
A DSL filter |
(not controlled by |
|
a wall switch) |
|
|
(not included) |
|
|
is required if |
Telephone base |
|
you have DSL |
|
|
high-speed |
power adapter |
Charger |
Internet service |
|
|
|
adapter |
|
|
|
Telephone line cord
Charger
Telephone base
Use only the power adapters and batteries supplied with this product.
Battery installation and charging
Install the battery as shown below. Once you have installed the battery, you may be able to make and receive short calls. For best performance, charge the handset battery continuously for at least 16 hours.
1Plug the battery connector securely into the socket.
3Slide the battery compartment cover towards the center of the handset until it clicks into place.
2Place the battery with the wires inside the battery compartment.
4Charge the handset in the telephone base or charger.
Charge light remains on when charging.
Enter the handset menu
1.Press MENU when the phone is not in use.
2.Press 
CID or 
until the screen displays the desired feature menu.
3.Press SELECT to enter that menu.
•To return to the previous menu, press CANCEL.
•To return to idle mode, press and hold CANCEL.
Set date and time
1.Press MENU when the handset is not in use.
2.Scroll to 
Settings then press SELECT.
3.Scroll to 
Set date/time then press SELECT.
4.Use the dialing keys (0-9) to enter the current month, date and year. Then press SELECT.
5.Use the dialing keys (0-9) to enter the hour and minute. Then press 
CID or 
to select AM or PM.
6.Press SELECT to save.
Set number of rings
You can set the answering system to answer an incoming call after 2, 3, 4, 5 or 6 rings; or toll saver. If you choose toll saver, the answering system answers a call after 2 rings when you have new messages, or after 4 rings when you have no
new messages.
1.Press MENU when the handset is not in use.
2.Scroll to 
Answering sys then press SELECT.
3.Scroll to 
Ans sys setup then press SELECT.
4.Scroll to 
# of rings then press SELECT.
5.Press 
CID or 
to choose 6, 5, 4, 3, 2 or Toll saver and then press SELECT to save.
Record your own announcement
You can use the preset announcement to answer calls, or replace it with your own recorded announcement. The announcement can be up to 90 seconds in length.
1.Press MENU when the handset is not in use.
2.Scroll to 
Answering Sys then press SELECT twice.
3.Press 7 to record.
4.After the handset announces, “Record after the tone. Press 5 when you are done,” speak towards the handset microphone.
5.Press 5 when done.
6.Press 2 to play the recorded announcement; or 7 to record again if desired. Press 3 to delete the recorded announcement. Press 5 to stop the playback at any time.
IMPORTANT!
Refer to the online user’s manual for a full set of installation and operation instructions. For manual download or customer service, visit our website at www.vtechphones.com or call
1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.
Copyright © 2011 for VTECH TELECOMMUNICATIONS LTD. All rights reserved. Printed in China.
96-007701-050-100
Loading...