K0022V3 3/09 Rev. A
ADEMCO 6150V & 6160V
Voice Remote Keypads
INSTALLATION AND SETUP GUIDE
GENERAL INFORMATION
The ADEMCO 6150V and ADEMCO 6160V are addressable remote keypads designed for use with ADEMCO control panels and provide the following features:
• Backlit Display |
• Voice Chime |
• Programmable Function Keys |
• Voice Status |
• Built-in Sounder |
• Message Center |
• Supervised by control panel (if supported)
Notes:
•When used with the ADEMCO VISTA-15P/VISTA- 20P control panels, address 16 must be assigned to the first keypad. Additional keypads must be assigned to address 17 – 23. Refer to Setting The Keypad Options.
•Keypad keys are continuously backlit for convenience.
•Permanent display backlighting is an option on some controls (refer to control panel’s instructions for details).
•Voice Chime should only be enabled when used with control panels that support the "chime by zone" mode (e.g., VISTA-15P/VISTA-20P). This mode must be enabled at the control panel. Refer to the control panel's installation and setup guide for information on how to program the chime mode.
•Use only zone descriptors supported by this keypad. If using zone descriptors not supported by this keypad, you must turn voice status and voice chime off. Table 1 is a list of applicable zone descriptors and index entries. Refer to the control panel’s installation and setup guide for information about how to program zone descriptors.
•For the 6160V ONLY, supervision must be enabled for commercial fire installations.
UL NOTE: ADEMCO 6150V cannot be used for commercial fire applications.
KEYPAD DISPLAYS AND LEDS
The keypads have the following display features:
Model |
Fixed |
2-Line |
2-Digit |
Custom |
|
Word |
Alpha |
Zone |
Zone |
|
Display |
Display |
Identifier |
Descriptors |
6150V |
X |
|
X |
|
6160V |
|
X |
|
X |
The following table identifies the keypad’s LEDs and associated functions:
LED |
Function |
ARMED |
Lights red when the system is armed in any mode. |
READY |
Lights green when the system is "ready" to be |
|
armed. |
MESSAGE |
Flashes red when message waiting or lights red |
|
(steady) when in record mode. |
PROGRAMMABLE FUNCTION KEYS
The keypad's programmable function keys [A, B, C] are normally used for keypad panic functions, but they can be programmed for other special functions instead. If they are programmed for other special functions, the associated keypad key pairs still provide the respective panic alarm (if programmed). Refer to the control panel’s Installation & Setup Guide for details.
Function |
Equivalent Key Pairs |
Keys |
|
A |
[1] and [*] |
B |
[*] and [#] |
C |
[3] and [#] |
D |
NONE |
•Function keys must be held down for at least 2 seconds to activate the programmed function.
•If functions other than panics are assigned to the programmable function keys, programmed panics must be initiated by pressing the programmed key pair.
FUNCTION KEY LABELS
A set of adhesive-backed labels with some typical function symbols (i.e., fire, police, personal emergency, etc.) is provided. These labels can be placed on or next to the keys to identify each key's function for the end user (as determined by the capability and programming of the control panel; refer to the installation and setup guide for the control panel).
A |
|
|
|
|
|
|
B |
|
RECORD |
VOLUME |
PLAY |
|
|
|
ARMED |
1 OFF |
2 AWAY |
3 STAY |
|
|
|
|
|
|
|||
|
READY |
4 MAX |
5 TEST |
6 BYPASS |
SIDE |
|
|
|
7 INSTANT |
8 CODE |
9 CHIME |
VIEW |
|
|
MESSAGE |
|
|
|||
C |
MIC |
READY |
0 |
# |
|
|
|
|
STATUS |
VOICE |
FUNCTION |
|
|
D |
|
|
|
|
|
|
|
|
MOUNTING RELEASE SNAPS |
|
-V1 |
||
|
|
|
001 |
|||
|
(Remove case back by pushing up the 2 "snaps" along |
|||||
|
6160V- |
|||||
|
the keypad's bottom edge and pulling the case apart.) |
WIRING AND INSTALLATION
Keypads can be surface mounted using drywall anchors or to a singleor double-gang electrical box.
1.Remove the case back by pushing up the two "snaps" along the keypad’s bottom edge and pulling the case apart. See diagram above.
2.Route wiring from the control panel through the opening in the case back.
3.Mount the case back to a wall or electrical box.
4.Wire directly from the keypad’s terminal block to the terminal block on the control board. (See Wiring Table that follows.) Use only 16-24 AWG wire.
Wiring Table (All Keypads)
Keypad |
Control Panel |
Wire Color |
G |
Data In |
Green |
– |
– Aux Pwr (GND) |
Black |
+ |
+ Aux. Pwr |
Red |
Y |
Data Out |
Yellow |
5.Re-attach the keypad to the case back.
6.Remove clear protective film from LEDs (6160V only).