Yamaha MSH-9150, MSH-9150S, MSH-8250 Manual

CARRYING HOLDER for MARCHING SNARE DRUM

MSH-9150(S)/8250

OWNER’S MANUAL

Thank you for purchasing the Yamaha Carrying Holder for Marching Snare Drum.

Please read this Owner’s Manual throughly before use.

MSH-9150

MSH-8250

Accessories

Hexagonal Wrench

Wrench

4mm

2500410 R1

Printed in Japan

■			■

AA B

B

CAUTION

Tighten all screws securely once adjustments have been made. If any screw is loose there is a danger that the drum may slip during performances or extraneous noises may be produced.

To tighten the arm section screws, use the hexagonal wrench provided. Tighten the wing nuts with your hands.

Be extra careful when removing the carrier with drum. Never drop or throw the instrument.

Avoid using the instrument in the rain whenever possible. If the instrument does get wet, wipe it with a soft, dry cloth as soon as possible.

Use a soft, dry cloth to wipe the instrument regularly. Never use thinners, benzene, or other similar solvents to clean the instrument.

When tilting the multi toms, be careful that the drum heads or hoops do not hit the holder when doing so.

Always take suitable breaks when playing the instrument for a long period of time.

When lifting the snare drum, always use

your hands to support and hold onto
the drum so that it does not fall		A
forward, hitting the person in
front of you and causing
injury. When returning
the drum to its normal
playing position, never
hold onto the drum at
the positions marked
“A” or “B” in the
illustration on the right.
Hands or fingers can	B
become pinched.

MSH-9150(S)

Snare Drum Mounting

				1.
			Slide-attachment
	Snare Drum
				2.
			Clamp Screw	3.
	Slide Base
		1	3	(
				( C
				))
	Frame Assembly		1
				( B )

3

3

Arm Bracket

Arm Bracket

B

Bolt

Arm

	3	1.	Mount the snare drum to the
			slide-at-tachment on the carrying holder
			slide base. Tighten the clamp screw to
		2.	secure the snare drum.
	2		Adjust the height and width of the carrying
			holder arms, and then tighten the screws
		3.	to secure.
			Insert the arms into the arm brackets on
		Carrying Holder	the frame assembly. (Position the
			instrument so that it is facing the holder
			(refer to diagram C).) Once the position is
	Notch for	Arm
			determined, tighten the screws on the arm
	securing
		C	brackets to secure the arms. When the
			instrument is properly positioned the
			screws lock into the notches.
		A
		The snare drum can be flipped up as shown
		at left to transport it or when changing
		marching formations. Be careful that the
		drum head or hoop does not come into
		contact with the holder. Be sure to hold the
		drum with your hand when flipped up.

WARNING

When tilting the drum up or returning it to its playing position, keep your hands

A away from the areas marked A as shown in the diagram on the left. Hands and/or fingers can get caught in this area resulting in injury.

	■	■ Removing the Snare Drum from
		the Carrying Holder
		When removing the snare drum from the carrying
		holder, the frame assembly is attached to the snare
		drum so loosen the screws on the arm bracket and
		remove the frame assembly from the arms.
		Also, when the placing the snare drum back on
		the carrying holder, make sure that the screws on
		the arm brackets are tightened to secure.
	■	■ Adjust the Height of the Drum
	●	●
	● Adjust the arm support	● Repositioning of the arm support brackets
	Tighten
		3
		3 positions
	Loosen
		9150S 2
		* 9150S: 2 positions
	■	■ Snare Head Angle Adjustment

●The angle of the snare drum head can be adjusted by using the angle adjustment nut.

Before proceeding, place the instrument on a flat surface.

1.Fold the carrying holder.

付属のスパナで緩めます。

2. Use the supplied wrench to loosen the angle adjustment nuts, located on the left and right sides.

Loosen

Angle Adjustment Nut

3.

3.To determine the angle, tilt the carrying holder.

4.Use the supplied wrench to tighten and secure the angle adjustment nuts making sure both sides are level.