Miele KM 460, KM 461, KM 463, KM 464, KM 465 Installation Instruction

Installation instructions

Ceramic hobs

KM 460 / KM 461 / KM 463

KM 464 / KM 465 / KM 466

KM 468 / KM 469

To avoid the risk of accidents	GiZHWOr
or damage to the machine
it is essential to read these
instructions before it is installed
or used for the first time.	M.-Nr. 05 397 194

Contents

Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety distance above the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation of appliance on wall with additional niche cladding . . . . . . . . . . . . . . . 5

Appliance dimensions and worktop cut-out . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 KM 460 / KM 461 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 KM 463. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 KM 464. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 KM 465 / KM 466 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 KM 468. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 KM 469. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Fitting the spring clamps and safety brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Installing the appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Granite worktops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Installing the appliance in granite worktops . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Important . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Electrical connection AUS/NZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Wiring diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

2

Safety instructions

Installation

Fit wall units and extractor hood before fitting the hob, to avoid damaging the ceramic surface.

The veneer or laminate coating of worktops (or adjacent kitchen

units) must be treated with 100°C heat-resistant adhesive which will not dissolve or distort.

Any backmoulds must be of heat-resis- tant material.

Ideally the hob should be installed with plenty of space on either side.

There may be a wall at the rear and a tall unit or wall at one side. On the other side, however, no unit or divider should stand higher than the hob (see illustrations).

This equipment is not designed for maritime use or for use in mobile

installations such as caravans, aircraft etc. However it may be suitable for such usage subject to a risk assessment of the installation being carried out by a suitably qualified engineer.

aMinimum distance between cut-out and tall unit/wall = 50 mm, unless they are made from a non-combustible material.

See: Installation of appliance on wall with additional niche cladding.

recommended

possible, but not recommended

not allowed

3

Safety instructions

Spray canisters, aerosols and other inflammable substances should not be stored in a drawer under the hob un-

less there is a shelf separating the drawer from the hob. If cutlery inserts are to be placed in the drawer, these must be made of a suitable heat-resis- tant material.

The hob may not be built in over a fridge, fridge-freezer, freezer, dish-

washer, washing machine or tumble dryer.

After installing the hob, ensure that the connection cable cannot come

into contact with the underside of the appliance. Make sure that there is no mechanical obstruction, such as a drawer, which could damage it.

Keep these instructions in a safe place and pass them on to any future owner of the appliance.

All dimensions in this instruction booklet are given in mm.

Safety distance above the appliance

bA minimum safety distance must be maintained between the hob and a cooker hood above it. See the manufacturer’s operating and installation instructions for details. For any flammable objects, e.g. utensil rails etc. a minimum safety distance of 760 mm should be maintained between it and the hob below.

When two or more appliances are installed together below a cooker hood, e.g. an electric hob and a gas wok combiset, which have different safety distances given in their installation instructions you should select the greater distance of the two.

4

Safety instructions

Installation of appliance on wall with additional niche cladding

c
b
d
e
min. 50	f
g

c
b
d
ee
min. 50	f
g

Hob with frame/bevel edge

Flush fit hob

aMasonry

bNiche cladding

cUpstand

dWorktop

eWorktop cut-out

f50 mm minimum distance between niche cladding and the worktop cut-out. This distance is only necessary for niche cladding made of wood or any other combustible material. For non-combustible materials (metal, ceramic tiles or similar), this dimension can be reduced by the thickness of the niche cladding material. The materials can warp or distort when subjected to high temperatures.

5

Appliance dimensions and worktop cut-out

KM 460 / KM 461

aSpring clamps

^Make the worktop cut-out following the dimensions shown above.

^Remember to maintain a minimum safety distance of 50 mm between the hob and the back wall and a side wall to the right or left of the hob. See "Warning and Safety instructions".

^Seal the cut surfaces with a suitable sealant to avoid swelling caused by moisture.

The materials used must be heat resistant.

bDepth for building in including the electrical connection box located at the rear on the right hand side approx. 48 mm.

If during installation the corners of the frame are not flush with the worktop surface, the corner radius, Max R4 can be carefully scribed to suit.

6

Appliance dimensions and worktop cut-out

KM 463

aSpring clamps

^Make the worktop cut-out following the dimensions shown above.

^Remember to maintain a minimum safety distance of 50 mm between the hob and the back wall and a side wall to the right or left of the hob. See "Warning and Safety instructions".

^Seal the cut surfaces with a suitable sealant to avoid swelling caused by moisture.

The materials used must be heat resistant.

bDepth for building in including the electrical connection box located at the rear on the right hand side approx. 48 mm.

If during installation the corners of the frame are not flush with the worktop surface, the corner radius, Max R4 can be carefully scribed to suit.

7

Appliance dimensions and worktop cut-out

KM 464

36	5
	a
max.R4

44	-	1
560
	+

75

e

75

aSpring clamps

590	c
	5
		51
		b
	50

+ 1 -

490

a

bDepth for building in including the electrical connection box located at the rear on the right hand side approx. 51 mm.

cHeight above worktop

eSafety bracket

^Make the worktop cut-out following the dimensions shown above.

^Remember to maintain a minimum safety distance of 50 mm between the hob and the back wall and a side wall to the right or left of the hob. See "Warning and Safety instructions".

^Seal the cut surfaces with a suitable sealant to avoid swelling caused by moisture.

The materials used must be heat resistant.

8