Metrohm 930 User Manual

930 Compact IC Flex

930 Compact IC Flex Oven

Manual – Short Instructions

8.930.8111EN

Metrohm AG CH-9100 Herisau Switzerland

Phone [phone] Fax [phone] [e-mail] www.metrohm.com

930 Compact IC Flex

930 Compact IC Flex Oven

2.930.2100

Manual – Short Instructions

8.930.8111EN

11.2013 zst

Teachware Metrohm AG CH-9100 Herisau

[e-mail]

This documentation is protected by copyright. All rights reserved.

Although all the information given in this documentation has been checked with great care, errors cannot be entirely excluded. Should you notice any mistakes please send us your comments using the address given above.

Documentation in additional languages can be found on

http://documents.metrohm.com.

Table of contents

Table of contents

1 About these Short Instructions		1
2 Introduction		2
2.1	Instrument description .........................................................	2
2.2	Intended use .........................................................................	3
2.3	Safety instructions ................................................................	4
2.3.1	General notes on safety ...........................................................	4
2.3.2	Electrical safety ........................................................................	4
2.3.3	Tubing and capillary connections .............................................	5
2.3.4	Flammable solvents and chemicals ...........................................	5
2.3.5	Recycling and disposal .............................................................	5
2.4	Symbols and conventions ....................................................	6

3 Overview of the instrument		7
3.1	Front ......................................................................................	7
3.2	Rear ........................................................................................	8
4 Installation		10
4.1	Setting up the instrument ..................................................	10
4.1.1	Packaging ..............................................................................	10
4.1.2	Checks ..................................................................................	10
4.1.3	Location ................................................................................	10
4.2	Removing transport locking screws .................................	10
4.3	Connecting the drainage tubing and leak sensor ............	12
4.3.1 Installing the drainage tubing ................................................		12
4.3.2 Connecting the leak sensor ....................................................		13
4.4	Column oven .......................................................................	14
4.5	Connecting the eluent bottle .............................................	14
4.6	Installing the high-pressure pump ....................................	16
4.7	Installing an inline filter .....................................................	16
4.8	Installing the pulsation absorber ......................................	16
4.9	Injection valve .....................................................................	16
4.10	Installing the detector ........................................................	16
4.11	Connecting the instrument to a computer .......................	17
4.12	Connecting the instrument to the power supply .............	18
4.13	Initial start-up .....................................................................	19

930 Compact IC Flex Oven (2.930.2100)

III

Table of contents
	4.14	Connecting and rinsing the guard column .......................	20
	4.15	Connecting the separation column	22
	4.16	Conditioning ........................................................................	24
5	Operation		26
6	Warranty (guarantee)		27
7	Accessories		29
	Index		31

IV	930 Compact IC Flex Oven (2.930.2100)

Table of figures

Table of figures
Figure 1	Front .................................................................................................	7
Figure 2	Rear ..................................................................................................	8
Figure 3	Removing the transport locking screws ............................................	11

930 Compact IC Flex Oven (2.930.2100)

V

1 About these Short Instructions

1 About these Short Instructions

This short instruction manual contains important chapters from the comprehensive manual. In addition to an introduction, safety instructions and an overview of the instrument, you will also find information about installing and operating the 930 Compact IC Flex Oven as well as information regarding the warranty. You can download the detailed manual as a PDF file from the Internet.

Downloading the manual

You can find the detailed manual on the Internet under http://documents.metrohm.com.

1.Click on Instruments Ion Chromatography.

2.Select the line of instruments, e.g. 930 Compact IC Flex.

3.Select the instrument.

All available manuals for the instrument will be displayed.

930 Compact IC Flex Oven (2.930.2100)

1

2.1 Instrument description

2 Introduction

2.1Instrument description

The 930 Compact IC Flex is a professional ion chromatograph. It is distinguished by:

Its intelligence: All of the functions are monitored, optimized and documented in an FDA-compatible manner. Intelligent components, such as iColumns, save important data onto a chip.

Its compact design: It has a small footprint.

Its transparency: All components are easily accessible and located for simple visibility and can be monitored during operation through a large window.

Its safety: The wet end and electronics are physically separated, thereby preventing fluids from coming into contact with the electronics to a large extent. A leak sensor is integrated into the wet end.

Its environmental compatibility.

Its low noise emissions.

The intelligent MagIC Net™ software

The 930 Compact IC Flex is operated solely using the MagIC Net software. A USB cable is used to connect the instrument to a computer with

MagIC Net installed. The intelligent software detects the instrument automatically and checks its functionality. The software controls and monitors the instrument, evaluates the measured data and manages it in a database.

The 930 Compact IC Flex Oven consists of the following modules:

Leak sensor

The leak sensor detects leaking liquid that collects in the instrument's base tray. Liquid that leaks in the instrument is routed to the base tray using drainage tubing and detected there.

Column oven

The column oven tempers the separation column and the eluent and thereby provides stable measuring conditions. A column holder with a chip reader is located in the column oven.

High-pressure pump

The intelligent and low-pulsation high-pressure pump pumps the eluent through the system. It is equipped with a chip where its technical specifications and "life history" (operating hours, service data, etc.) are saved.

2	930 Compact IC Flex Oven (2.930.2100)

2 Introduction

Inline filter

Inline filters protect the separation column reliably from potential contamination from the eluent. The small filter pads with 2 µm pore size can be replaced quickly and easily. They remove particles from the solutions, such as bacteria and algae.

Pulsation absorber

The pulsation absorber protects the separation column from damage caused by pressure fluctuations when switching the injection valve, and reduces interfering pulsations during highly sensitive measurements.

Injection valve

The injection valve connects the eluent path to the sample path. By a quick and precise switching of the valve a quantity of sample solution defined by the size of the sample loop is injected and flushed to the separation column with the eluent.

Detector

Metrohm offers a series of different detectors for various analysis tasks. A suitable detector type must be ordered as a separate accessory.

Separation column

The intelligent separation column separates different components according to their interactions with the column. Metrohm separation columns are equipped with a chip where their technical specifications and history (start-up, operating hours, etc) are stored.

2.2Intended use

The 930 Compact IC Flex Oven is used for the determination of cations and anions without suppression using ion chromatography.

The present instrument is suitable for processing chemicals and flammable samples. Usage of the 930 Compact IC Flex therefore requires the user to have basic knowledge and experience in handling toxic and caustic substances. Knowledge with respect to the application of the fire prevention measures prescribed for laboratories is also mandatory.

930 Compact IC Flex Oven (2.930.2100)

3

2.3 Safety instructions

2.3Safety instructions

2.3.1General notes on safety

WARNING

This instrument may only be operated in accordance with the specifications in this documentation.

This instrument has left the factory in a flawless state in terms of technical safety. To maintain this state and ensure non-hazardous operation of the instrument, the following instructions must be observed carefully.

2.3.2Electrical safety

The electrical safety when working with the instrument is ensured as part of the international standard IEC 61010.

WARNING

Only personnel qualified by Metrohm are authorized to carry out service work on electronic components.

WARNING

Never open the housing of the instrument. The instrument could be damaged by this. There is also a risk of serious injury if live components are touched.

There are no parts inside the housing which can be serviced or replaced by the user.

Mains voltage

WARNING

An incorrect mains voltage can damage the instrument.

Only operate this instrument with a mains voltage specified for it (see rear panel of the instrument).

4	930 Compact IC Flex Oven (2.930.2100)