Samsung CS-21A550, CS-21A550ML, CS-21B860AR, CS-29Z57M5, CS-21A760SL Manual

COLOUR TELEVISION

CS21Z45/21Z47/21Z43/21Z50/

21Z57/21Z55/21Z58/21AF0/

21AE0

Owner’s Instructions

Before operating, please read this manual thoroughly, and retain it for future reference.

Register your product at www.samsung.com/global/register.

Record your Model and Serial number.

▪ Model __________ ▪ Serial No. __________

Control Panel (depending on the model)

Themodel.product colour and shape may vary depending on the

Front (or Side) Panel

1On-screen menu display

2Volume adjustment

3Channel selection

4Remote control sensor

5Standby indicator

6Power on/off

You can use the 3 buttons to switch the TV on when it is in standby mode depending on the model.

The 2 and 3 buttons also have the same function as the

◄/►/▲/▼ buttons on the remote control.

If the remote control no longer works or you have misplaced it, you can use the controls on the panel of the television.

Connection Panel (depending on the model)

The product colour and shape may vary depending on the model.

Rear Panel

or

cable television network

or

cable television network

or

cable television network

or

cable television network

continued...

English -

Whenever you connect an audio or video system to your television, ensure that all elements are switched off.

Please be sure to match the colour coded input terminals and cable jacks.

Connecting to an Aerial or Cable Television Network

Connect the aerial or network input cable to the 1 (75 Ω coaxial socket). To view television channels correctly, a signal must be received by the set from one of the sources: an outdoor aerial, cable television network, or satellite network. If you are using an indoor aerial, you may need to adjust it when tuning your television until you obtain a picture that is both sharp and clear.

Connecting to the RCA Output

The RCA2 connectors are used for equipment, such as a recording VCR or audio system.

Connecting to the RCA Input

The RCA3,4 connectors are used for equipment, such as a VCR, DVD, decoder, satellite receiver, video game device, or video disc player. (When using the mono equipment, connect to the AUDIO-L input connector.) The RCA5 connectors are used for equipment such as a DVD with component output (480i/576i).

continued...

AA68-03996A-00

	Front (or Side) Panel
		1
	1
		2
	2
	3
	1	1
	2	2
	3	3
	1 Audio input	1
	2 Video input
	3 Headphone jack
		2

Connecting to the RCA Input

The 1 (AUDIO-L/R or AUDIO) and 2 (VIDEO) connectors are used for equipment, such as a camcorder, video disc player, or video game device.

Connecting Headphones

The 3 (headphone) jack is used for watching a television programme without disturbing the other people in the room. Prolonged use of headphones at a high volume may damage your hearing.

When both the front (or side) AV and rear connectors are connected to external equipment, the front (or side)AV receives priority.

Remote Control (depending on the model)

Operation of remote control may be affected by bright artificial light near to the TV.

This is a special remote control for the visually impaired, and has Braille points on the POWER, Channel and Volume buttons.

	1 POWER	3 -/--
	Used to switch the TV	Used to select a
	on and off.	channel numbered
	2 Numeric buttons	ten or over. Press this
		button, then “--” symbol
	Used to select channels
		is displayed. Enter
	directly.
		the two-digit channel
		number.

4 /

Used to increase or decrease the volume.

5MENU

Used to display the on-screen menu or return to the previous menu.

6▲/▼/◄/►

Used to control the cursor in the menu.

7S.MENU (option) Used to display the sound menu.

8TURBO (option)

Used to select the turbo sound option.

9DUAL I-II (option)

Used to select the sound mode.

0SOURCE

Used to display all of the available video sources.

!INFO

Used to view the channel information and setting status you selected.

@PRE-CH

Used to switch repeatedly between the last two channels displayed.

Installing Batteries

#P / P

Used to display the next or previous stored channel.

$ EXIT

Used to exit from any display or return to normal viewing.

%MUTE

Used to switch the sound off temporarily. To turn the sound back on, press the MUTE, , or button.

^ENTER

While using the on-screen menus, press the ENTER button to activate (or change) a particular item.

&S.MODE (option) Used to select the sound effect.

*P.MODE

Used to select the picture effect.

( TV

Used to return to the TV mode when it is in external input mode.

) SLEEP

Used to select a preset time interval for automatic turn off.

Remove the cover. Install two AAA size batteries, then replace the cover.

When the remote control does not operate

normally, check that the “+” and “–” ends of the batteries are inserted correctly or the batteries are drained.

Do not mix battery types, i.e. alkaline and manganese.

English -

Switching the Television On and Off

The mains lead is attached to the rear of the television

1Plug the mains lead into an appropriate socket.

The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.

2Press the “ I ” button (On/Off) on the front (or side) of the television.

3Press the POWER button on the remote control to switch the television on. The programme that you were watching last is re-selected automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Channel - Auto Store” on page 3 or “Channel - Manual Store” on page 4.

If the television is initially powered on, several basic customer settings proceed automatically.

Refer to “Setup - Plug & Play” on page 3.

4To switch the television off, press the “ I ” button (On/Off) on the front (or side) of the television.

Placing the Television in Standby Mode

The television can be placed in standby mode, in order to reduce power consumption and wear of the cathode ray tube. Standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).

1Press the POWER button on the remote control while viewing.

The television is in standby mode.

2To switch the television back on, simply press it again.

You can also switch on by pressing the TV, P / P , or numeric button.

Do not leave the television in standby mode for long periods of time (when you are away on holiday, for example). Turn the television off by pressing the “ I ” button (On/Off) on the front (or side) of the television. It is best to unplug the set from the mains and aerial.

Viewing the Menus

1Press the MENU button.

The main menu is displayed on the screen. Its left side has five icons: Input, Picture, Sound, Channel, and Setup.

2Press the ▲ or ▼ button to select one of the icons.

Press the ENTER button to access the icon’s sub-menu.

3Press the ▲ or ▼ button to move to items in the menu.

Press the ENTER button to enter items in the menu.

4Press the ▲/▼/◄/► button to change the selected items.

Press the MENU button to return to the previous menu.

5Press the EXIT button to exit from the menu.

Setup - Plug & Play (depending on the model)

When the television is initially powered on, several basic customer settings proceed automatically and subsequently. The following settings are available.

1If the television is in standby mode, press the POWER button on the remote control. The message Start Plug & Play. is displayed.

To start Plug & Play, press the ENTER button.

The Language menu is displayed.

The Language menu will automatically appear after several seconds, even if the ENTER button is not pressed.

2Select the appropriated language by pressing the

▲ or ▼ button. Press the

ENTER button.

The Check antenna input. is displayed.

Plug & Play

Start Plug & Play.

OK

Enter Exit

Plug & Play

Language

English

Français

Indonesia

Melayu

Türkçe	Enter	Skip
Move
Plug & Play
Check	antenna	input.
	OK
Enter		Skip

If any language is not selected, the language menu will disappear about 30 seconds later.

continued...

3To search the channels, press the ENTER button.

To stop the search, press the ENTER button.

When the channel searching has finished, the Clock Set menu is displayed.

4Press the ◄ or ► button to move to the hour or minute. Set the hour or minute by pressing the ▲ or ▼ button.

5When you have finished, press the MENU button. The Enjoy your watching. is displayed, and then the channel which has been stored will be activated.

Re-setting the Plug & Play

Method:

MENU  ▲/▼ (Setup)  ENTER  ▲/▼ (Plug & Play)

 ENTER

					Plug	&	Play
	Auto			Store
					Start
				Enter				Skip
					Plug	&	Play
	Auto			Store				102MHz
	P 1
								7	%
					Stop
				Enter				Skip
					Plug	&	Play
		Clock Set
							1 2 : 0 0 a m
				Move				Enter
				Adjust				Skip
				Enjoy your watching.
						OK
	TV							Setup
			Plug		& Play				►
			Language			: English			►
			Time						►
			Child		Lock				►
			Blue		Screen		: Off		►
			Move			Enter		Return

English -