Samsung CLX 8640, CLX 8650 Service Manual

Color Laser MFP

CLX-8640/8650 series

CLX-8640ND, CLX-8650ND

(Ver1.0)

SERVICEMANUAL

Color Laser MFP

Contents

1. Precautions

2. Product specifications and Description

3. Disassembly and Reassembly

4. Troubleshooting

5. System Diagram

6. Reference Information

Refer to the service manual in the GSPN (see the rear cover) for more information.

Contents

Contents

1. Precautions ........................................................................................................................................				1 − 1
1.1.	Safety warning ..........................................................................................................................			1 − 1
1.2.	Caution for safety ......................................................................................................................			1 − 2
	1.2.1.	Toxic material...............................................................................................................		1 − 2
	1.2.2.	Electric shock and fire safety precautions ...........................................................................		1 − 2
	1.2.3.	Handling precautions .....................................................................................................		1 − 3
	1.2.4.	Assembly and Disassembly precautions.............................................................................		1 − 3
	1.2.5.	Disregarding this warning may cause bodily injury ..............................................................		1 − 4
1.3.	ESD precautions........................................................................................................................			1 − 5
2. Product specifications and Description ....................................................................................................				2 − 1
2.1.	Product Overview......................................................................................................................			2 − 1
2.2.	Specifications............................................................................................................................			2 − 2
	2.2.1.	General .......................................................................................................................		2 − 2
	2.2.2.	Print............................................................................................................................		2 − 3
	2.2.3.	Controller and Software..................................................................................................		2 − 4
	2.2.4.	Scan............................................................................................................................		2 − 8
	2.2.5.	Copy...........................................................................................................................		2 − 9
	2.2.6.	Fax ...........................................................................................................................		2 − 11
	2.2.7.	Paper Handling ...........................................................................................................		2 − 14
	2.2.8.	Consumables ..............................................................................................................		2 − 17
	2.2.9.	Maintenance Parts .......................................................................................................		2 − 18
	2.2.10.	Options .....................................................................................................................		2 − 19
2.3.	System Configuration ...............................................................................................................			2 − 20
2.4.	Feeding System.......................................................................................................................			2 − 25
	2.4.1.	Cassette.....................................................................................................................		2 − 25
	2.4.2.	Pick-Up Unit ..............................................................................................................		2 − 26
	2.4.3.	Registration Unit.........................................................................................................		2 − 27
	2.4.4.	MPF(Multi-Purpose Feeder) Unit ...................................................................................		2 − 28
	2.4.5.	Exit Unit....................................................................................................................		2 − 29
	2.4.6.	Duplex Unit ...............................................................................................................		2 − 30
2.5.	Fuser unit...............................................................................................................................			2 − 31
2.6.	Image Creation........................................................................................................................			2 − 32
	2.6.1.	Printing process overview .............................................................................................		2 − 32
	2.6.2.	Imaging Unit ..............................................................................................................		2 − 33
		2.6.2.1.	Imaging Unit Overview..................................................................................	2 − 33
		2.6.2.2.	Drum drive ..................................................................................................	2 − 34
		2.6.2.3.	Developer Unit .............................................................................................	2 − 35
	2.6.3.	ITB (Intermediate Transfer Belt) Unit..............................................................................		2 − 37

i	Copyright© 1995-2013 SAMSUNG. All rights reserved.

				Contents
		2.6.3.1.	ITB Unit overview ........................................................................................	2 − 37
		2.6.3.2.	Transfer belt drive .........................................................................................	2 − 38
		2.6.3.3.	Transfer belt cleaning.....................................................................................	2 − 39
2.7.	Laser scanning unit (LSU).........................................................................................................			2 − 40
	2.7.1.	LSU overview.............................................................................................................		2 − 40
	2.7.2.	Laser Scanning Optical path ..........................................................................................		2 − 41
	2.7.3.	Laser synchronizing detectors ........................................................................................		2 − 42
2.8.	Drive System ..........................................................................................................................			2 − 43
	2.8.1.	Drive Motors..............................................................................................................		2 − 43
	2.8.2.	Main Drive Unit (OPC, DEVE, ITB, T1 DIS_ENG)...........................................................		2 − 45
	2.8.3.	PH(Paper Handling) Drive ............................................................................................		2 − 46
	2.8.4.	Fuser_Exit Drive.........................................................................................................		2 − 47
	2.8.5.	Cst Lift Drive .............................................................................................................		2 − 48
	2.8.6.	Toner Supply Drive......................................................................................................		2 − 48
	2.8.7.	Waste Toner Container Drive.........................................................................................		2 − 49
	2.8.8.	ITB Auger Drive .........................................................................................................		2 − 49
2.9.	Duplex Automatic Document Feeder(DADF)................................................................................			2 − 50
	2.9.1.	DADF overview..........................................................................................................		2 − 50
	2.9.2.	Electrical parts location ................................................................................................		2 − 51
	2.9.3.	DADF Drive System....................................................................................................		2 − 53
2.10.	Hardware Configuration............................................................................................................			2 − 55
	2.10.1.	Main Controller ..........................................................................................................		2 − 58
	2.10.2.	OPE controller............................................................................................................		2 − 62
	2.10.3.	ADF PBA	..................................................................................................................	2 − 65
	2.10.4.	TCF(Triple Cassette Feeder) PBA...................................................................................		2 − 69
	2.10.5.	SMPS board ...............................................................................................................		2 − 70
	2.10.6.	Fuser Drive Board (FDB)..............................................................................................		2 − 72
	2.10.7.	HVPS board ...............................................................................................................		2 − 73
	2.10.8.	Eraser PBA ................................................................................................................		2 − 75
	2.10.9.	Fuser PBA .................................................................................................................		2 − 75
	2.10.10.	CRUM PBA...............................................................................................................		2 − 76
	2.10.11.	Deve CRUM Joint PBA ...............................................................................................		2 − 76
	2.10.12.	Toner CRUM Joint PBA ..............................................................................................		2 − 76
	2.10.13.	ITB Encoder PBA .......................................................................................................		2 − 77
	2.10.14.	Toner Connector PBA ..................................................................................................		2 − 77
	2.10.15.	Connector PBA...........................................................................................................		2 − 78
	2.10.16.	Side Joint PBA ...........................................................................................................		2 − 78
	2.10.17.	Finisher IF PBA .........................................................................................................		2 − 79
	2.10.18.	Paper Size PBA ..........................................................................................................		2 − 79
	2.10.19.	Sensor locations ..........................................................................................................		2 − 80

Copyright© 1995-2013 SAMSUNG. All rights reserved.

ii

Contents

3. Disassembly and Reassembly ................................................................................................................			3 − 1
3.1. Precautions when replacing parts ..................................................................................................			3 − 1
3.1.1.	Precautions when assembling and disassembling .................................................................		3 − 1
3.1.2.	Precautions when handling PBA.......................................................................................		3 − 1
3.1.3.	Releasing Plastic Latches................................................................................................		3 − 2
3.2. Replacing the maintenance part ....................................................................................................			3 − 3
3.2.1.	Drum Unit....................................................................................................................		3 − 3
3.2.2.	Developer Unit .............................................................................................................		3 − 4
3.2.3.	ITB Unit......................................................................................................................		3 − 6
3.2.4.	Fuser Unit	....................................................................................................................	3 − 7
3.2.5.	Transfer Roller..............................................................................................................		3 − 7
3.2.6.	Pick-Up_Reverse_Forward roller......................................................................................		3 − 8
3.2.7.	DADF Pick-up roller Assy ..............................................................................................		3 − 9
3.2.8.	DADF Reverse roller Assy............................................................................................		3 − 10
3.2.9.	MP Rollers.................................................................................................................		3 − 10
3.3. Replacing the main SVC part .....................................................................................................			3 − 15
3.3.1.	Left Cover..................................................................................................................		3 − 15
3.3.2.	Rear Cover.................................................................................................................		3 − 15
3.3.3.	HVPS........................................................................................................................		3 − 16
	3.3.3.1.	HVPS board1 ...............................................................................................	3 − 16
	3.3.3.2.	HVPS board2 ...............................................................................................	3 − 16
3.3.4.	Temperature Sensor .....................................................................................................		3 − 17
3.3.5.	ITB Waste Auger Drive Unit .........................................................................................		3 − 17
3.3.6.	LSU..........................................................................................................................		3 − 18
3.3.7.	Main board.................................................................................................................		3 − 19
3.3.8.	SMPS board ...............................................................................................................		3 − 19
3.3.9.	Main Drive Unit..........................................................................................................		3 − 20
3.3.10.	SMPS shield...............................................................................................................		3 − 20
3.3.11.	CST Lift Drive unit......................................................................................................		3 − 21
3.3.12.	Fuser Drive Board .......................................................................................................		3 − 21
3.3.13.	Paper Size Sensor........................................................................................................		3 − 22
3.3.14.	PH(Paper Handling) Drive Unit......................................................................................		3 − 22
3.3.15.	Fuser Drive Unit .........................................................................................................		3 − 23
3.3.16.	Toner Supply Drive Unit...............................................................................................		3 − 24
3.3.17.	Side Unit ...................................................................................................................		3 − 25
	3.3.17.1. MP Pick Up Unit...........................................................................................		3 − 26
	3.3.17.2.	Duplex Exit Sensor........................................................................................	3 − 29
	3.3.17.3.	Duplex Motor...............................................................................................	3 − 30
	3.3.17.4.	Duplex Fan ..................................................................................................	3 − 30
3.3.18.	Exit Unit....................................................................................................................		3 − 31

iii	Copyright© 1995-2013 SAMSUNG. All rights reserved.

				Contents
	3.3.19.	Pick Up Unit ..............................................................................................................		3 − 32
	3.3.20.	OPE Unit...................................................................................................................		3 − 33
	3.3.21.	DADF Unit ................................................................................................................		3 − 34
		3.3.21.1.	DADF Hinge................................................................................................	3 − 34
		3.3.21.2.	DADF Cover................................................................................................	3 − 35
		3.3.21.3.	DADF Board................................................................................................	3 − 37
		3.3.21.4.	DADF Stacker..............................................................................................	3 − 37
		3.3.21.5.	DADF COVER-OPEN...................................................................................	3 − 38
		3.3.21.6.	DADF GUIDE-PICK UP ASSY ......................................................................	3 − 39
		3.3.21.7.	DADF-EXIT UP...........................................................................................	3 − 40
		3.3.21.8. HOLDER-HARNESS....................................................................................		3 − 40
		3.3.21.9. COVER-FAN DUCT and COVER-FAN............................................................		3 − 41
		3.3.21.10. DADF-CCDM..............................................................................................		3 − 41
		3.3.21.11. DADF Drive ................................................................................................		3 − 42
	3.3.22.	Scanner .....................................................................................................................		3 − 43
		3.3.22.1.	Scan Glass ...................................................................................................	3 − 43
		3.3.22.2.	APS Sensor..................................................................................................	3 − 44
		3.3.22.3.	Filter...........................................................................................................	3 − 44
		3.3.22.4.	COVER-GLASS ADF ...................................................................................	3 − 45
		3.3.22.5.	Scan Joint Board ...........................................................................................	3 − 45
		3.3.22.6.	Fan.............................................................................................................	3 − 46
		3.3.22.7.	CCDM........................................................................................................	3 − 47
		3.3.22.8.	Scanner Assy................................................................................................	3 − 48
	3.3.23.	SCF (Second Cassette Feeder) with Stand ........................................................................		3 − 49
		3.3.23.1.	SCF Main Board ...........................................................................................	3 − 49
		3.3.23.2. SCF Lift Motor Assy .....................................................................................		3 − 50
		3.3.23.3. SCF Feed Motor Assy....................................................................................		3 − 51
		3.3.23.4.	FOOT .........................................................................................................	3 − 53
	3.3.24.	TCF (Triple Cassette Feeder).........................................................................................		3 − 55
		3.3.24.1.	TCF Main Board...........................................................................................	3 − 55
		3.3.24.2. TCF Lift Motor Assy .....................................................................................		3 − 55
		3.3.24.3. TCF Feed Motor Assy....................................................................................		3 − 56
		3.3.24.4.	FOOT .........................................................................................................	3 − 58
	3.3.25.	Finisher .....................................................................................................................		3 − 60
	3.3.26.	HDD (Hard Disk Drive)................................................................................................		3 − 64
4. Troubleshooting..................................................................................................................................				4 − 1
4.1.	Control Panel............................................................................................................................			4 − 1
	4.1.1.	Introducing the display screen and useful buttons ................................................................		4 − 2
4.2. Understanding the status LED ......................................................................................................				4 − 6
4.3.	Updating Firmware		....................................................................................................................	4 − 7

Copyright© 1995-2013 SAMSUNG. All rights reserved.

iv

Contents

4.3.1. Updating from the Printer Control Panel			............................................................................4 − 7
4.3.2. Updating from the Network ............................................................................................			4 − 9
4.4. JAM removal..........................................................................................................................			4 − 12
4.4.1. Clearing original document jams ....................................................................................			4 − 12
4.4.2.	Clearing paper jams .....................................................................................................		4 − 18
4.5. Service Mode (Tech Mode)........................................................................................................			4 − 33
4.5.1. Entering and Exiting Service Mode.................................................................................			4 − 33
4.5.2. Service Mode Menu Tree .............................................................................................			4 − 34
4.5.3.	Information ................................................................................................................		4 − 38
	4.5.3.1.	General .......................................................................................................	4 − 38
	4.5.3.2.	Supply Status ...............................................................................................	4 − 38
	4.5.3.3.	Software Version...........................................................................................	4 − 39
	4.5.3.4.	Service Hours...............................................................................................	4 − 39
	4.5.3.5.	Fault Log.....................................................................................................	4 − 39
	4.5.3.6.	Print Reports ................................................................................................	4 − 40
	4.5.3.7.	Export Reports..............................................................................................	4 − 41
4.5.4.	Maintenance Counts.....................................................................................................		4 − 42
	4.5.4.1.	Fault Count .................................................................................................	4 − 42
	4.5.4.2.	Jam Count ...................................................................................................	4 − 42
	4.5.4.3.	Part Replacement Count .................................................................................	4 − 43
	4.5.4.4.	Finisher Handling Count.................................................................................	4 − 44
4.5.5.	Diagnostics ................................................................................................................		4 − 45
	4.5.5.1.	Engine Diagnostics........................................................................................	4 − 45
	4.5.5.2.	Fax Diagnostics ............................................................................................	4 − 51
	4.5.5.3.	Scanner Diagnostics.......................................................................................	4 − 53
	4.5.5.4.	Adjustment ..................................................................................................	4 − 55
	4.5.5.5. ACS (Auto Color Sensing) .............................................................................		4 − 62
	4.5.5.6.	Image Management ......................................................................................	4 − 63
	4.5.5.7.	Print Test Patterns .........................................................................................	4 − 67
4.5.6.	Service Functions ........................................................................................................		4 − 68
	4.5.6.1.	Main Memory Clear ......................................................................................	4 − 68
	4.5.6.2.	Hard Disk Maintenance..................................................................................	4 − 68
	4.5.6.3.	Toner Save ..................................................................................................	4 − 68
	4.5.6.4.	Port ............................................................................................................	4 − 68
	4.5.6.5.	Debug Log...................................................................................................	4 − 69
	4.5.6.6.	Capture Log .................................................................................................	4 − 69
	4.5.6.7.	System Recovery ..........................................................................................	4 − 70
	4.5.6.8.	TR Control Mode .........................................................................................	4 − 73
	4.5.6.9.	User Data Management .................................................................................	4 − 74
4.6. Error Code and Troubleshooting .................................................................................................			4 − 75

v	Copyright© 1995-2013 SAMSUNG. All rights reserved.

			Contents
		4.6.1. Ax-xxxx type error code ...............................................................................................	4 − 84
		4.6.2. Cx-xxxx type error code .............................................................................................	4 − 116
		4.6.3. H1-xxxx type (Optional Cassette) error code...................................................................	4 − 158
		4.6.4. H2-xxxx type (Finisher) error code ...............................................................................	4 − 175
		4.6.5. Mx-xxxx type error code.............................................................................................	4 − 202
		4.6.6. Sx-xxxx type error code..............................................................................................	4 − 219
		4.6.7. U1-xxxx type (Fuser) error code...................................................................................	4 − 239
		4.6.8. U2-xxxx type (LSU) error code....................................................................................	4 − 249
		4.6.9. U3-xxxx type(DADF) error code..................................................................................	4 − 251
	4.7. Image quality problems and solutions ........................................................................................		4 − 262
	4.8.	Other errors ..........................................................................................................................	4 − 271
5.	System Diagram..................................................................................................................................		5 − 1
6.	Reference Information..........................................................................................................................		6 − 1
	6.1.	Tools for Troubleshooting............................................................................................................	6 − 1
	6.2.	Glossary...................................................................................................................................	6 − 3

Copyright© 1995-2013 SAMSUNG. All rights reserved.

vi

1. Precautions

1. Precautions

In order to prevent accidents and damages to the equipment please read the precautions listed below carefully before servicing the product and follow them closely.

1.1. Safety warning

1)Only to be serviced by a factory trained service technician.

High voltages and lasers inside this product are dangerous. This product should only be serviced by a factory trained service technician.

2)Use only Samsung replacement parts.

There are no user serviceable parts inside the product. Do not make any unauthorized changes or additions to the product as these could cause the product to malfunctions and create an electric shocks or fire hazards.

3)Laser Safety Statement

The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR, chapter 1 Subchapter J for Class I(1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 60825-1. Class I laser products are not considered to be hazardous. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance or prescribed service condition.

•Wavelength: 800 nm

•Beam divergence

-Paraller: 11 degrees

-Perpendicular: 35 degrees

•Maximum power of energy output: 12 mW

WARNING

Never operate or service the product with the protective cover removed from Laser/Scanner assembly. The reflected beam, although invisible, can damage your eyes.

When using this product, these basic safety precautions should always be followed to reduce risk of fire, electric shock, and personal injury.

1-1	Copyright© 1995-2013 SAMSUNG. All rights reserved.

1. Precautions

1.2. Caution for safety

1.2.1. Toxic material

This product contains toxic materials that could cause illness if ingested.

1)Please keep imaging unit and toner cartridge away from children. The toner powder contained in the imaging unit and toner cartridge may be harmful, and if swallowed, you should contact a doctor.

1.2.2. Electric shock and fire safety precautions

Failure to follow the following instructions could cause electric shock or potentially cause a fire.

1)Use only the correct voltage, failure to do so could damage the product and potentially cause a fire or electric shock.

2)Use only the power cable supplied with the product. Use of an incorrectly specified cable could cause the cable to overheat and potentially cause a fire.

3)Do not overload the power socket, this could lead to overheating of the cables inside the wall and could lead to a fire.

4)Do not allow water or other liquids to spill into the product, this can cause electric shock. Do not allow paper clips, pins or other foreign objects to fall into the product, these could cause a short circuit leading to an electric shock or fire hazard.

5)Never touch the plugs on either end of the power cable with wet hands, this can cause electric shock. When servicing the product, remove the power plug from the wall socket.

6)Use caution when inserting or removing the power cord. When removing the power cord, grip it firmly and pull. The power cord must be inserted completely, otherwise a poor contact could cause overheating leading to a fire.

7)Take care of the power cable. Do not allow it to become twisted, bent sharply around corners or power cable may be damaged. Do not place objects on top of the power cable. If the power cable is damaged it could overheat and cause a fire. Exposed cables could cause an electric shock. Replace the damaged power cable immediately, do not reuse or repair the damaged cable. Some chemicals can attack the coating on the power cable, weakening the cover or exposing cables causing fire and shock risks.

8)Ensure that the power sockets and plugs are not cracked or broken in any way. Any such defects should be repaired immediately. Take care not to cut or damage the power cable or plugs when moving the machine.

9)Use caution during thunder or lightning storms. Samsung recommends that this machine be disconnected from the power source when such weather conditions are expected. Do not touch the machine or the power cord if it is still connected to the wall socket in these weather conditions.

10)Avoid damp or dusty areas, install the product in a clean well ventilated location. Do not position the machine near a humidifier or in front of an air conditioner. Moisture and dust built up inside the machine can lead to overheating and cause a fire or cause parts to rust.

11)Do not position the product in direct sunlight. This will cause the temperature inside the product to rise possibly leading to the product failing to work properly and in extreme conditions could lead to a fire.

12)Do not insert any metal objects into the machine through the ventilator fan or other part of the casing, it could make contact with a high voltage conductor inside the machine and cause an electric shock.

13)When replacing the SMPS board, please wait 5 minutes after unplugging the power cord, then replace it. You can get a shock by the electric discharge.

Copyright© 1995-2013 SAMSUNG. All rights reserved.

1-2

1. Precautions

1.2.3. Handling precautions

The following instructions are for your own personal safety to avoid injury and so as not to damage the product.

1)Ensure the product is installed on a level surface, capable of supporting its weight. Failure to do so could cause the product to tip or fall.

2)The product contains many rollers, gears and fans. Take great care to ensure that you do not catch your fingers, hair or clothing in any of these rotating devices.

3)Do not place any small metal objects, containers of water, chemicals or other liquids close to the product which if spilled could get into the machine and cause damage or a shock or fire hazard.

4)Do not install the machine in areas with high dust or moisture levels, beside on open window or close to a humidifier or heater. Damage could be caused to the product in such areas.

5)Do not place candles, burning cigarettes, etc on the product, These could cause a fire.

1.2.4. Assembly and Disassembly precautions

1)Replace parts carefully and always use Samsung parts. Take care to note the exact location of parts and also cable routing before dismantling any part of the machine. Ensure all parts and cables are replaced correctly. Please carry out the following procedures before dismantling the product or replacing any parts.

2)Ensure that power is disconnected before servicing or replacing any electrical parts.

3)Disconnect interface cables and power cables.

4)Only use approved spare parts. Ensure that part number, product name, any voltage, current or temperature rating are correct.

5)When removing or re-fitting any parts do not use excessive force, especially when fitting screws into plastic.

6)Take care not to drop any small parts into the machine.

7)Handling of the OPC Drum

•The OPC Drum can be irreparably damaged if it exposed to light. Take care not to expose the OPC Drum either to direct sunlight or to fluorescent or incandescent room lighting. Exposure for as little as 5 minutes can damage the surface of the photoconductive properties and will result in print quality degradation. Take extra care when servicing the product. Remove the OPC Drum and store it in a black bag or other lightproof container. Take care when working with the Covers (especially the top cover) open as light is admitted to the OPC area and can damage the OPC Drum.

•Take care not to scratch the green surface of OPC Drum Unit. If the green surface of the Drum Cartridge is scratched or touched the print quality will be compromised.

1-3	Copyright© 1995-2013 SAMSUNG. All rights reserved.

1. Precautions

1.2.5. Disregarding this warning may cause bodily injury

1)Be careful with the high temperature part.

The fuser unit works at a high temperature. Use caution when working on the printer. Wait for the fuser unit to cool down before disassembly.

2)Do not put fingers or hair into the rotating parts.

When operating a printer, do not put hand or hair into the rotating parts (Paper feeding entrance, motor, fan, etc.). If do, you can get harm.

3)When you move the printer, use safe lifting and handling techniques.

This printer is heavy. Use the lifting handles located on each side of the machine. Back injury could be caused if you do not lift carefully.

4)Ensure the printer is installed safely.

Ensure the printer is installed on a level surface, capable of supporting its weight. Failure to do so could cause the printer to tip or fall possibly causing personal injury or damaging the printer.

5)Do not install the printer on a sloping or unstable surface. After installation, double check that the printer is stable.

Copyright© 1995-2013 SAMSUNG. All rights reserved.

1-4

1. Precautions

1.3. ESD precautions

Certain semiconductor devices can be easily damaged by static electricity. Such components are commonly called “Electrostatically Sensitive (ES) Devices” or ESDs. Examples of typical ESDs are: integrated circuits, some field effect transistors, and semiconductor “chip” components. The techniques outlined below should be followed to help reduce the incidence of component damage caused by static electricity.

CAUTION

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

1)Immediately before handling a semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, employ a commercially available wrist strap device, which should be removed for your personal safety reasons prior to applying power to the unit under test.

2)After removing an electrical assembly equipped with ESDs, place the assembly on a conductive surface, such as aluminum or copper foil, or conductive foam, to prevent electrostatic charge buildup in the vicinity of the assembly.

3)Use only a grounded tip soldering iron to solder or desolder ESDs.

4)Use only an “anti-static” solder removal device. Some solder removal devices not classified as “anti-static” can generate electrical charges sufficient to damage ESDs.

5)Do not use Freon-propelled chemicals. When sprayed, these can generate electrical charges sufficient to damage ESDs.

6)Do not remove a replacement ESD from its protective packaging until immediately before installing it. Most replacement ESDs are packaged with all leads shorted together by conductive foam, aluminum foil, or a comparable conductive material.

7)Immediately before removing the protective shorting material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed.

8)Maintain continuous electrical contact between the ESD and the assembly into which it will be installed, until completely plugged or soldered into the circuit.

9)Minimize bodily motions when handling unpackaged replacement ESDs. Normal motions, such as the brushing together of clothing fabric and lifting one’s foot from a carpeted floor, can generate static electricity sufficient to damage an ESD.

1-5	Copyright© 1995-2013 SAMSUNG. All rights reserved.

2. Product specifications and Description

2. Product specifications and Description

2.1. Product Overview

•Printing Speed (Mono/Color)

•CLX-8650 series : Up to 48 ppm in A4 (51 ppm in Letter)

•CLX-8640 series : Up to 38 ppm in A4 (40 ppm in Letter)

•Processor

•Dual Core 1GHz

•Memory

•1GB DDR3 SDRAM

•320 GB HDD

Copyright© 1995-2013 SAMSUNG. All rights reserved.

2-1

2. Product specifications and Description

2.2. Specifications

Product Specifications are subject to change without notice.

2.2.1. General

	Item		Specification
	Temperature	Operating	10 to 32 °C (50 to 90 °F)
		Storage	-20 to 40 °C (-4 to 104 °F)
	Humidity	Operating	20 to 80% RH
		Storage	10 to 90% RH
	Acoustic Noise Level	Ready mode	43 dB(A)
	(Sound Power /	Printing mode	55 dB(A)
	Pressure)
		Copying mode	59 dB(A)
			Europe : AC 220-240V(-10%~6%)
	Power Supply	Input Voltage	USA : AC 110~127V (-10%~6%)
			Korea : AC 220-240V(-10%~6%)
		Rated Frequency	50 / 60 Hz
		Ready	< 80 Watt
		AVG. (Normal	< 1000 Watt
	Power Consumption	Operation)
		Sleep/Power Off	< 1.5 Watt / < 0.1 Watt
		TEC	•	CLX-8640ND : 3.6 KWh
			•	CLX-8650ND : 3.7 KWh
	Dimension (W x D x	Set	550 x 523 x 776 mm (21.7 x 20.6 x 30.6 inches)
	H)
	Weight	Set	70.4 Kg (155.21 lbs)
		(with consumables)
	Reliability & Service	Recommended Printing	7,000 sheets/month (60% Color ratio)
		Volume (AMPV)
		Max Monthly Duty	200,000 sheets/month

2-2	Copyright© 1995-2013 SAMSUNG. All rights reserved.

2. Product specifications and Description

2.2.2. Print

	Item		Specification
			•	CLX-8640ND
				• B&W : Up to 38 ppm in A4 (40 ppm in Letter)
		Simplex		• Color : Up to 38 ppm in A4 (40 ppm in Letter)
			•	CLX-8650ND
				• B&W : Up to 48 ppm in A4 (51ppm in Letter)
	Engine Speed			• Color : Up to 48 ppm in A4 (51ppm in Letter)
			•	CLX-8640ND
				• B&W : Up to 31 ppm in A4 (33 ppm in Letter)
		Duplex		• Color: Up to 31 ppm in A4 (33 ppm in Letter)
			•	CLX-8650ND
				• B&W : Up to 40 ipm in A4 (42 ipm in Letter)
				• Color: Up to 40 ipm in A4 (42 ipm in Letter)
		From Ready	Less than 9 sec
	FPOT (B&W and	From Sleep	Less than 15 sec
	Color)	From Coldboot	• Less than 64 sec @ Panel Soft Power
			• Less than 90 sec @ Mechanical Power
	Resolution	Optical	1200 x 600 dpi
		Enhanced	Up to 9,600 x 600 dpi effective output
	Printer Languages		PCL5C, PCL6, PostScript Level3, PDF 1.7
	Fonts		• PCL : 93 scalable, 1 bitmap
			•	PS : 136
	Downloadable Fonts		Yes (PCL & PS3 S/W Font)
	USB Memory Direct Print		Jpeg, Tiff, PDF

Copyright© 1995-2013 SAMSUNG. All rights reserved.

2-3

2. Product specifications and Description

2.2.3. Controller and Software

Item		Specification
Processor		1GHz Dual Core
Memory	Std.	1GB DDR3
Memory Expansion		N/A
Storage		320GB HDD Standard
		[Windows]
		• Windows 2000, XP 32/64bits, Vista 32/64bits, Windows 7
		32/64bits, Windows 2003 Server 32/64bits, Windows Server 2008
		32/64bits, Windows Server 2008 R2 64bits
		[Linux]
		• RedHat Enterprise Linux WS 4, 5 (32/64 bit)
		• Fedora 5, 6, 7, 8, 9, 10, 11, 12, 13 (32/64 bit)
		• SuSE Linux 10.1 (32 bit)
	Supporting OS	• OpenSuSE 10.2, 10.3, 11.0, 11.1, 11.2 (32/64 bit)
		• Mandriva 2007, 2008, 2009, 2009.1, 2010 (32/64 bit)
		• Ubuntu 6.06, 6.10, 7.04, 7.10, 8.04, 8.10, 9.04, 9.10, 10.04 (32/64
		bit)
		• SuSE Linux Enterprise Desktop 10, 11 (32/64 bit)
		• Debian 4.0, 5.0 (32/64 bit) - Sun Solaris 9,10 (x86, SPARC)
		• HP-UX 11.0, 11i v1, 11i v2, 11i v3 (PA-RISC, Itanium)
		• IBM AIX 5.1, 5.2, 5.3, 5.4
Printer driver
		[Mac]
		• Mac OS X 10.4 ~ 10.6
	Default Driver	• PCL6 (for Windows)
		• PS (for Mac, Linux)
		[Windows]
		• Watermark, Overlay, N-up printing, Poster printing
		• Duplex, Quality, Color mode (Color, Gray scale)
	Driver feature	• Support Color spec., Device color, color management
		[Mac/Linux]
		• N-up printing, Duplex, Quality
		• Color mode (Color, Gray scale)
	WHQL	Windows 2000/XP(include 64bit)/ 2003/ Vista/ 2008/ Win7/ 2008 R2 (64bit
		only)
	Language Localization	English, French, German, Italian, Spanish, Korean, Russian, Brazilian
		Portuguese
	UPD (SSPD)	Yes

2-4	Copyright© 1995-2013 SAMSUNG. All rights reserved.

2. Product specifications and Description

	Item		Specification
		TWAIN	Yes
		WIA	Yes (N/W, USB2.0 only)
			[Windows]
			• Windows 2000, XP 32/64bits, Vista 32/64bits, Windows 7
				32/64bits, Windows 2003 Server 32/64bits, Windows Server 2008
				32/64bits, Windows Server 2008 R2 64bits
			[Linux]
			• RedHat Enterprise Linux WS 4, 5 (32/64 bit)
	Scan driver		• Fedora 5, 6, 7, 8, 9, 10, 11, 12, 13 (32/64 bit)
			• SuSE Linux 10.1 (32 bit)
		Supporting OS
			• OpenSuSE 10.2, 10.3, 11.0, 11.1, 11.2 (32/64 bit)
			• Mandriva 2007, 2008, 2009, 2009.1, 2010 (32/64 bit)
			• Ubuntu 6.06, 6.10, 7.04, 7.10, 8.04, 8.10, 9.04, 9.10, 10.04 (32/64
				bit)
			• SuSE Linux Enterprise Desktop 10, 11 (32/64 bit)
			• Debian 4.0, 5.0 (32/64 bit)
			[Mac]
			• Mac OS X 10.4 ~ 10.6
			Yes (Windows, Mac)
		Scan Manager	•	Status Monitoring feature
			•	Scan2PC / Fax2PC
			•	Device Setting
		PC-FAX	Yes
		NW-FAX	Yes
	Application	OCR	ReadIRIS
		Smart Panel	Yes (Linux) EPM is provided for Windows/Mac
		Network Management	Set IP, SWAS 4.0 & SWS SWAS Plug-In
			- Job Accounting, Storage management, Cloning, Remote Install
		HDD File Management	SWS2.0 (Document Box)
		S/W
		AnyWeb Print	Yes
		SmarThru	Smarthru Office, SmarThru Workflow(Optional)

■ Interface

	Item		Specification
	Parallel (IEEE 1284)		No
	USB	Type A	High-Speed USB 2.0 Host (2 Ports)
		Type B	Hi-Speed USB 2.0 Peripheral (1Port)
	Wired LAN		Ethernet 10/100/1000 Base TX
	Wireless LAN		No
	Foreign Device Interface		Optional

Copyright© 1995-2013 SAMSUNG. All rights reserved.

2-5

2. Product specifications and Description

■ Network Interface

	Item		Specification
			[Windows]
			• Microsoft Windows 2000/ XP(32/64bits)/ 2003(32/64bits)/
			Vista(32/64bits)2008/ Win7/ 2008 R2(64 only)
			[Mac]
			• Mac OS 10.4 ~10.6
			[Linux]
	Network OS		• RedHat 8 ~ 9
			• Fedora Core 1~4
			• Madrake 9.2 ~ 10.1
			• SuSE 8.2 ~ 9.2
			[Novell]
			• Netware 5.x, 6.x(TCP/IP Only)
			[Others]
			• Unix(HP-UX,Solaris,SunOS, SCO)
		TCP/IP	TCP/IPv4, HTTP, SNMPv1/v2c/v3, LDAP, SMTP, SSL/TLS, IPSec,
			DNS,WINS, SLP, Bonjour, SSDP,DDNS, DHCP/BOOTP,IPv6
	NW Protocols	IPX/SPX	No
		Ether Talk	No
		NetBIOS over TCP/IP	Yes
		Others	HTTPS,LDAPS,SMTPS,802.1x,IPSec
		Static IP	Yes
	IP Addressing	Auto IP	Yes
		BOOTP	Yes
		DHCP	Yes
		MIB-2(RFC 1213)	Yes
		Host Resource MIB	Yes
		(RFC 2790)
		Printer MIB (RFC	Yes
		3805)
	SNMP/MIB Access
		Finisher MIB (RFC	Yes
		3806)
		Samsung Private MIB	Yes
		HP Compatibility	Yes - Patially
		SNMP Trap	Yes
		Window Printing	No
		(SMB)
		LPR/LPD	Yes
	Printing Protocols	IPP	Yes
		Netware I-Print	Yes
		Netware NDPS	No
		Ether Talk	No
		Port 9100	Yes

2-6	Copyright© 1995-2013 SAMSUNG. All rights reserved.

2. Product specifications and Description

	Item		Specification
		DNS	Yes
		Dynamic DNS	Yes
		Multicast	Yes
		DNS(Bonjoure)
	Device Discovery
		WSD (incl. Print &	NO
		Scan)
		SLP	Yes
		uPNP(SSDP)	Yes

■ Memory (HDD) Management

	Item		Specification
		Type	Public, Private, System
	Box Management	Stored Job Type	Print / Copy / Scan / Fax
		Max. Number of Boxes	Up to 100
		Box Size	Up to HDD Space
		Creation	Folder
		Rename	Folder, File
		Move & Copy	Yes
		Delete	Yes
	Basic Management	Search	Search(Name,Owner)
		Display detail	Name,Owner,Job Type,Size,Page,Date
		information
		Select	Multi File Select
		Auto Delete Time	Yes
		Setting
		Email	Yes
	Memory to	Client	Yes
		Server	Yes
		Copies	Yes
	Memory to Print	Duplex Printing	Yes
		Color Mode	Yes
	Setting
		Autofit	Yes
		Paper Supply	Yes
	Image Overwrite	Immediate	Yes
		On-Demand	Yes
		Supported Job Type	Print / Scan / Fax
	Data Encrytion	Cryptography	AES
		Key length	128bit

Copyright© 1995-2013 SAMSUNG. All rights reserved.

2-7

2. Product specifications and Description

2.2.4. Scan

	Item		Specification
	Scan method		Color CCDM, Dual Scan
	Compatibility		TWAIN(USB & N/W), WIA(Only for USB)
	Color Mode		Mono / Gray / Color
	Scan Speed		• Simplex 50 ipm @ 300 dpi
			• Duplex 70 ipm @ 300 dpi
	Resolution	Optical	600 x 600 ppi
		Enhanced	4,800 x 4,800 ppi
	Halftone		256 levels
		Max. Document Width	Max. 216mm (8.5")
	Scan Size	Effective Scan Width	Max. 208mm (8.2inch)
		Max. Document	Max. 356mm (Legal)
		Length
		Color	24 bits
	Scan Depth
		Mono	• 1bit for Linearity & Halftone
			• 8Bits for Gray scale
	Multi-page Scan		Platen & ADF
		HDD	Yes (Document Box)
		USB	Yes
		Email	Yes
	Scan-to	Client(NetScan)	Yes
		SMB	Yes
		FTP	Yes
		HTTP(S)	No
		Multi Destination	No
		Email, Fax,	User Based Individual (Fax+Email) : 200
			Fax Group : 100, E-mail Group : 200
		Server	10
	Address Book		Searching
			Editing
		Basic Feature	Deleting
			Grouping
			import, export
		Mixed Document	Yes
		Scan Preset	Yes
	Scan Setting	Delayed Send	Yes
		Job Done notice	Yes
		Job Recall	Yes
		OCR	Yes

2-8	Copyright© 1995-2013 SAMSUNG. All rights reserved.

2. Product specifications and Description

2.2.5. Copy

	Item		Specification
			•	CLX-8640ND
				• Color Simplex : up to 38 cpm in A4 (40 cpm in Letter)
				• Mono Simplex: up to 38 cpm in A4 (40 cpm in Letter)
		SDMC (Single		• Color Duplex : up to 31 cpm in A4 (33 cpm in Letter)
	Copy Speed (Dual			• Mono Duplex : up to 31 cpm in A4 (33 cpm in Letter)
		Document Multiple
	Scan)		•	CLX-8650ND
		Copy) @ 300 dpi
				• Color Simplex : up to 48 cpm in A4 (51 cpm in Letter)
				• Mono Simplex: up to 48 cpm in A4 (51 cpm in Letter)
				• Color Duplex : up to 40 cpm in A4 (42 cpm in Letter)
				• Mono Duplex : up to 40 cpm in A4 (42 cpm in Letter)
		From Ready	Less than 9 sec
	FCOT (B&W and	From Sleep	15 sec
	Color)	From Coldboot	• Less than 64 sec @ Panel Soft Power
			• Less than 90 sec @ Mechanical Power
	Zoom Range		• 25% ~ 400% in 1% increments (Platen)
			• 25% ~ 200% in 1% increments (DADF)
	Multi Copy		1~999
		Text	•	Platen: Scan 600 x 600 dpi , Printing 600 x 600 dpi
			• DADF: Scan 300 x 300 dpi, Printing 600 x 600 dpi
		Text/Photo	•	Platen: Scan 600 x 600 dpi, Printing 600 x 600 dpi
			• DADF: Scan 300 x 300 dpi, Printing 600 x 600 dpi
	Original Type
		Megazine	•	Platen: Scan 600 x 600 dpi , Printing 600 x 600 dpi
			• DADF: Scan 300 x 300 dpi, Printing 600 x 600 dpi
		Photo	•	Platen: Scan 600 x 600 dpi, Printing 1200 x 1200 dpi
			• DADF: Scan 300 x 300 dpi, Printing 600 x 600 dpi
	Original Type	Factory Default	Color copy mixed mode
		Auto Color	Yes
		Full Color	Yes
	Color Setting	Twin Color	N/A
		Single Color	N/A
		B&W	Yes
	Max. Original Size	Platen	Legal (8.5" x 14")
		DADF	Legal (8.5" x 14")

Copyright© 1995-2013 SAMSUNG. All rights reserved.

2-9

2. Product specifications and Description

	Item		Specification
		Multi Copy	1~999
		Automatic Paper	Yes - Patially(Legal, A4/Letter, A5 )
		Selection
		Manual Paper Selection	Yes
		Multi-page Copy	Platen & ADF
			Using Platen, DADF
			•	1→1
			•	1→2Book
			•	1→2Calendar
		Duplex Copy	•	2→1Book
			•	2→1Calendar
			•	2→2Book
			•	2Calendar→2Calendar
			•	2Book→2Calendar
			•	2Calendar→2Book
		Darkness Control	11 levels
	Basic Copy
		Automatic Background	Auto, Erase(4 levels), Enhance(2 levels)
		Suppression
		Collation Copy	Yes
			* Zoom Range : 25% to 400% in Platen, 25% to 200% in ADF
			* Preset [Original(100%)]
			[Auto Fit] [A4 → A5(71%)]
			[LGL→LTR(78%)]
		Reduce & Enlarge	[LGL→A4(83%)]
			[A4→LTR(94%)]
			[EXE→LTR(104%)]
			[A5 → A4(141%)] 25%, 50%,150%, 200%, 400%
			[Custom:25-400%)]
			•	Not Collated
			• Collated (This is collated output without Staple)
		Output	• Collated and Offset (This is collated output and offset without
				Staple)
			• Staple (This is staple and Offset)
		Proof Copy	No
		N-Up	2up, 4-up
		ID Card Copy	Yes (Platen only)
		Poster Copy	No
	Other Features	Clone Copy	No
		Booklet	No
		Covers	No
		Transparencies	No
		Book Copy	No
		Interrupt Copy	Yes

2-10	Copyright© 1995-2013 SAMSUNG. All rights reserved.

2. Product specifications and Description

Item		Specification
	Erase Edge	No
	Save to File	Yes
	Margin Shift	No
	Book Center Erase	Yes
	Form Copy	No
Image	Watermark Copy	Yes
	Page Numbering	No
	Time & Date Stamp	Yes
	ID Stamp	Yes

2.2.6. Fax

	Item		Specification
	Compatibility		ITU-T G3, Super G3
	Communication System		PSTN/PABX
	Modem Speed		33.6Kbps
	TX Speed		3sec (Mono/Standard/ECM-MMR, ITU-T G3 No.1 Chart)
	Compression		MH/MR/MMR/JBIG/JPEG
	Color Fax		Yes
	ECM		Yes
		Std	203*98dpi
	Resolution (Mono)	Fine	203*196dpi
		S.Fine Photo	No
		S.Fine	300*300dpi
		Std	200*200dpi
	Resolution (Color)	Fine	200*200dpi
		S.Fine	200*200dpi
		Std	1.5sec/LTR
	Scan speed	Fine	4sec/LTR
		S.Fine	Depends on Document
		Handset	No
		On hook Dial	Yes
		Search	Yes(Phone Book)
		Speed Dial	200 locations
	Telephone Features	Group Dial	Max. 100 Groups (Max. locations per 1 Group : 200 locations)
		TAD I/F	Yes
		Tone/Pulse	Yes
		Pause	Yes
		Auto Redial	Yes
		Last Number Redial	Yes

Copyright© 1995-2013 SAMSUNG. All rights reserved.

2-11

2. Product specifications and Description

	Item		Specification
		Distinctive Ring	No
		Caller ID	Yes
		External Phone	Yes
		Interface
		Mail Box	No
		Voice Request	No
		TTI	Yes
		RTI	Yes
		Polling	No
		Earth/Recall	No
		Auto Reduction	Yes
		SMS	No
	Functions	Multi-send	Same as Group Dial Capacity.
		Delayed Send	Yes
		Memory RX	Yes
		Secure Rx (<-secure	Yes
		TX)
		Time Secured Fax	No
		Relay Transmission	No
		(ITU-T Mail Box)
		Priority Transmission	Yes
		Batch Transmission	No
		Searching	Yes
		Storing	Yes
	Address Book Basic	Editing	Yes
		Deleting	Yes
	Feature
		Grouping	Yes
		Chaining	No
		import, export	Yes
		Search condition	No
	Address Book	Favorites Button	No
		Curent Sending ,
	Advanced		Yes(Curent Sending )
		Receiving Tel number
		LDAP	Yes
		Check the Success or	Yes
		Fail & Error
		Re-Faxing from
	Sending fax	memory in case of	Yes
		failed Fax
	Management
		Re-Faxing in case of	Yes
		failed page.
		Delete in memory after	Yes
		sending completely

2-12	Copyright© 1995-2013 SAMSUNG. All rights reserved.

			2. Product specifications and Description
	Item		Specification
		Separator Sheet	No
	Fax Receiving Feature/	Insert the stamp	Yes(Option -On,Off) Rx Time ,ID, Page
		Number of Printing	No
	Printing the Rx	Copies
	Document
		Revers order printing	No
		tray selection	Yes
		Tx/Rx Journal	Yes
	Report & List Print out	Confirmation	2 types available (with Image TCR, w/o image TCR,Mono Only)
		Auto Dial List	Yes
		System Data List	List all user setting
		Ring Volume	Yes(Off,Low,MED,HIGH)
	Sound Control	Key Volume	Yes(On,Off)
		Speaker	Yes(On,Off)
		Alarm Volume	Yes(On,Off)
	Junk Fax barrier		Yes
	Security Receive		Yes
	Battery Backup		Permanently stored on HDD
	Duplex	Send	Yes
		Receive	Yes
	Receive Mode		Fax, TEL, Ans/Fax
	Battery Backup		HDD Store, 500 jobs
	Fax Forward to FAX		Yes(On/Off), both Sent and Received
	Fax Forward to e-mail		Yes
	Broadcasting		up to 209 locations
	Cover page		No
		HDD	Yes
		USB	No
		Fax	Yes
		Email	Yes
	Fax-to	Client	No
		SMB	Yes
		FTP	Yes
		HTTP(S)	No
		Multi-destination	No

Copyright© 1995-2013 SAMSUNG. All rights reserved.

2-13

2. Product specifications and Description

2.2.7. Paper Handling

Item		Specification
Standard Capa.		• 520-sheet cassette Tray (20 lb or 80g/m²),
		• 100-sheet MP tray (20 lb or 80g/m²)
Max. Input Capa.	MP + 4 Tray	2,180 sheets @ 20lb or 80g/m²
	Max. Size	216 x 1200 mm (8.5" x 47.2"), Banner size
Printing	Min. Size	98 x 148 mm (3.85" x 5.83")
	Margin(T/B/L/R)	4 mm, 4 mm, 4 mm, 4 mm
		• Plain paper : 100 sheets
	Capacity	•	Envelopes : 10 sheets
		•	Labels : 10 sheets
	Media sizes	98 x 148 mm (3.85" x 5.83") ~ 216 x 356 mm (8.5" x 14")
		Banner Size Printing : 216mm x 1200mm
		Printer Default, Plain Paper, Thick Paper, Thin Paper, Bond Paper, Color
	Media type	Paper, CardStock, Labels, Envelope, Preprinted, Letterhead, Recycled
		Paper, Cotton, Archive, User set
		•	Thin: 60-75 g/m²
		•	Colored 1: 75-84 g/m²
		•	Coloerd 2: 85-10 5 g/m²
		•	Pre-Printed 1: 75-84 g/m²
		•	Pre-Printed 2: 85-105 g/m²
		•	Cotton: 75-90 g/m²
		•	Plain Paper: 76-84 g/m²
		•	Thick 1: 85-110 g/m²
		•	Thick 2: 111-130 g/m²
MP Tray		•	Recycle: 60-80 g/m²
		•	Envelope: 75-90 g/m²
		•	Gloss 1: 105-130 g/m²
	Media weight	•	Gloss 2: 131-220g/m²
		•	Extra Thick 1: 111-130 g/m²
		•	Extra Thick 2: 131-170g/m²
		•	Cardstock: 171-220 g/m²
		•	Bond 1: 84 g/m²
		•	Bond 2: 85-110 g/m²
		•	Bond 3: 111-130 g/m²
		•	Bond 4: 131-220 g/m²
		•	Archive 1: 84 g/m²
		•	Archive 2: 85-110 g/m²
		•	Archive 3: 111-130 g/m²
		•	Archive 4: 131-220 g/m²
		•	Transparency: 138-146 g/m²
		•	Label: 120-150 g/m²
	Sensing	Paper empty sensor

2-14	Copyright© 1995-2013 SAMSUNG. All rights reserved.

2. Product specifications and Description

	Item		Specification
		Capacity	520 sheets @ 20lb (80g/m²)
		Media sizes	Tentative Letter, Legal, Oficio, Folio, A4, JIS B5, ISO B5, Executive, A5,
			Envelope C5, Custom
		Media types	Tentative Plain Paper, Thin Paper, Bond, Pre-Printed, Recycled, Envelope,
			CardStock, Thick, Cotton, Colored, Archive
			•	Thin: 60-75 g/m²
			•	Colored 1: 75-84 g/m²
			•	Coloerd 2: 85-105 g/m²
			•	Pre-Printed 1: 75-84 g/m²
			•	Pre-Printed 2: 85-105 g/m²
			•	Cotton: 75-90 g/m²
			•	Plain Paper: 76-84 g/m²
			•	Thick 1: 85-110 g/m²
			•	Thick 2: 111-130 g/m²
			•	Recycle: 60-80 g/m²
			•	Envelope: 75-90 g/m²
	Standard Cassette Tray	Media weight	•	Gloss 1: 105-130 g/m²
			•	Gloss 2: 131-163 g/m²
			•	Extra Thick 1: 111-130 g/m²
			•	Extra Thick 2: 131-163 g/m²
			•	Cardstock: 171-163 g/m²
			•	Bond 1: 84 g/m²
			•	Bond 2: 85-110 g/m²
			•	Bond 3: 111-130 g/m²
			•	Bond 4: 131-163 g/m²
			•	Archive 1: 84 g/m²
			•	Archive 2: 85-110 g/m²
			•	Archive 3: 111-130 g/m²
			•	Archive 4: 131-163 g/m²
			• H/W Install Detect: Yes
		Sensing	• Paper Empty & Low Level Detect: Yes
			• Paper Type Detect: No
			• Paper Size Detect: Legal, Letter, A4, B5, A5, Folio and others
		Capacity	520 sheets @ 20lb (80 g/m²), drawer type
		Media sizes	Letter, Legal, Oficio, Folio, A4, JIS B5, ISO B5, Executive, A5, Envelope
	Optional Cassette Tray		C5, Custom
		Media types	Plain Paper, Thin Paper, Bond, Pre-Printed, Recycled, Envelope, CardStock,
			Thick, Cotton, Colored, Archive

Copyright© 1995-2013 SAMSUNG. All rights reserved.

2-15

2. Product specifications and Description

Item		Specification
		•	Thin: 60-75 g/m²
		•	Colored 1: 75-84 g/m²
		•	Coloerd 2: 85-105 g/m²
		•	Pre-Printed 1: 75-84 g/m²
		•	Pre-Printed 2: 85-105 g/m²
		•	Cotton: 75-90 g/m²
		•	Plain Paper: 76-84 g/m²
		•	Thick 1: 85-110 g/m²
		•	Thick 2: 111-130 g/m²
		•	Recycle: 60-80 g/m²
		•	Envelope: 75-90 g/m²
	Media weight	•	Gloss 1: 105-130 g/m²
		•	Gloss 2: 131-163 g/m²
		•	Extra Thick 1: 111-130 g/m²
		•	Extra Thick 2: 131-163 g/m²
		•	Cardstock: 171-163 g/m²
		•	Bond 1: 84 g/m²
		•	Bond 2: 85-110 g/m²
		•	Bond 3: 111-130 g/m²
		•	Bond 4: 131-163 g/m²
		•	Archive 1: 84 g/m²
		•	Archive 2: 85-110 g/m²
		•	Archive 3: 111-130 g/m²
		•	Archive 4: 131-163 g/m²
		• H/W Install Detect: Yes
	Sensing	• Paper Empty & Low Level Detect: Yes
		• Paper Type Detect: No
		• Paper Size Detect: Legal, Letter, A4, B5, A5, Folio and others
	Capacity	• 500 sheets @ 20lb (80g/m²)
	(FaceDown)
Output Stacking
	Offset Stacking	N/A
	Output Full sensing	Yes
	Capacity	•	Main tray : 500 sheets @ 20lb (80g/m²)
	(FaceDown)	•	Top tray : 100 sheets @ 20lb (80g/m²)
2-bin Finisher	Offset Stacking	Yes
	Stapling Method	1 Position
	Sensing	Output Full sensing: Yes Cartridge Empty Detect : Yes
	Supporting	Yes
	Throughput	85% from Cassette, 30% from MP tray
Automatic Duplex	Media sizes	148.5 x 210 mm - 215.9 x 355.6 mm
	Media types	Plain/Thick Paper
	Media weight	60 to 163 g/m²

2-16	Copyright© 1995-2013 SAMSUNG. All rights reserved.

2. Product specifications and Description

Item		Specification
	Capacity	100 sheets ( 20lb, 80 g/m²)
	2-sided Document	Yes (Reversing) -> Dual scan
	Scanning
		•	Width: 145 ~ 216 mm (5.7"~8.5")
		•	Length :
ADF	Document Size		• 145 ~ 356 mm (5.7" ~ 14.0") for Single page scan
			• 145 ~ 400 mm (5.7" ~ 15.7") for Multi pages scan
		• Bank Check Scan : 69.6 mm x 152.4 mm
	Document Weight	12.5~28 lb
		• Paper empty detect : Yes
	Sensing	•	Paper width detect : Yes
		• Paper length detect : Yes

2.2.8. Consumables

Items			Model Name	Life
Toner Cartridge		Black	CLT-K659S	20,000 standard pages
		Yellow	CLT-Y659S	20,000 standard pages
		Magenta	CLT-M659S	20,000 standard pages
		Cyan	CLT-C659S	20,000 standard pages
Drum Unit		Black	CLT-R659K	40,000 pages (3 sheets/job)
		Yellow	CLT-R659Y	40,000 pages (3 sheets/job)
		Magenta	CLT-R659M	40,000 pages (3 sheets/job)
		Cyan	CLT-R659C	40,000 pages (3 sheets/job)
Waste Toner Container			CLT-W659	20,000 pages

Copyright© 1995-2013 SAMSUNG. All rights reserved.

2-17

2. Product specifications and Description

2.2.9. Maintenance Parts

Items		Part Code		Life
Developer Unit	Black	JC96-06327A		300,000 impressions (3 sheets/ job)
	Yellow	JC96-06324A		300,000 impressions (3 sheets/ job)
	Magenta	JC96-06325A		300,000 impressions (3 sheets/ job)
	Cyan	JC96-06326A		300,000 impressions (3 sheets/ job)
Fuser Unit		•	JC91-01121A (220V)	150,000 impressions
		•	JC91-01120A (110V)
ITB Unit		JC96-06322A		150,000 impressions
Transfer roller Assy		JC95-01622A		150,000 impressions
Pick up/ Reverse/ Forward roller (Tray		JC93-00616A		150,000 impressions
1,2,3,4)
DADF Pick-Up roller Assy		JC97-04098A		150,000 impressions
DADF Retard roller Assy		JC97-04135A		150,000 impressions

NOTE

Depending on the print patterns and job mode used, the lifespan may differ.

2-18	Copyright© 1995-2013 SAMSUNG. All rights reserved.