Samsung CS-29Z45MH, CS-29Z50MH, CS-29Z40MH, CS-29Z57MV, CS-21M40ML Manual

COLOR TELEVISION

CS-29Z40/29Z45/29Z50/29Z57/29Z58 29U50/29U57

Owner’s Instructions

Before operating, please read this manual thoroughly, and retain it for future reference.

Register your product at

www.samsung.com/global/register

Control Panel(depending on the model)

The actual configuration of your TV may be different, depending on your model.

Front (or Side) Panel

1 Remote control sensor

2 Standby indicator

3 Power on/off

4 On-screen menu display

5 Volume adjustment

6Channel selection

You can use the 6 buttons to switch the TV on when it is in standby mode depending on the model.

The 5 and 6 buttons also have the same function as the œ/√/†/… buttons on the remote control.

If the remote control no longer works or you have misplaced it, you can use the controls on the panel of the television.

Connection Panel(depending on the model)

The actual configuration of your TV may be different, depending on your model.

Rear Panel

or

cable television network

Whenever you connect an audio or video system to your television, ensure that all elements are switched off. Please be sure to match the color coded input terminals and cable jacks.

Connecting to an Aerial or Cable Television Network

Connect the aerial or network input cable to the 1 (75 Ω coaxial socket).

To view television channels correctly, a signal must be received by the set from one of the sources: an outdoor aerial, cable television network, or satellite network.

If you are using an indoor aerial, you may need to adjust it when tuning your television until you obtain a picture that is both sharp and clear.

Connecting to the SCART Input/Output

The SCART2 and SCART3 connectors are used for equipment, such as a VCR, DVD, decoder, satellite receiver, video game device, or video disc player.

The SCART2 is also used for equipment with an RGB output, such as a video game device or video disc player.

continued...

English - 1

Connecting to the RCA Output

The RCA6 connectors are used for equipment, such as a recording VCR or audio system.

Connecting to the RCA Input

The RCA4 and RCA5 connectors are used for equipment, such as a VCR, DVD, decoder, satellite receiver, video game device, or video disc player. (When using the mono equipment, connect to the AUDIO-L input connector.)

The RCA7 connectors are used for equipment such as a DVD with component output.

Front (or Side) Panel

3 S-Video input

2 Video input

1 Audio input

Please be sure to match the color coded input terminals and cable jacks.

Connecting to the RCA Input

The 1 (AUDIO-L/R) and 2 (VIDEO) connectors are used for equipment, such as a camcorder, video disc player, or video game device.

Connecting to the S-VIDEO Input

The 3 (S-VIDEO IN) and 1 (AUDIO-L/R) connectors are used for equipment with an S-Video output, such as a camcorder or VCR.

AA68-03867A-06

Remote Control(depending on the model)

Operation of remote control may be affected by bright artificial light near to the TV.

1POWER

Used to switch the TV on and off.

2Numeric buttons

Used to select channels directly.

3-/--

Used to select a channel numbered ten or over. Press this button, then “--” symbol is displayed. Enter the two-digit channel number.

4 /

Used to increase or decrease the volume.

5MENU

Used to display the onscreen menu or return to the previous menu.

6… / † / œ / √

Used to control the cursor in the menu.

7S.MENU

Used to display the sound menu.

8TURBO

Used to select the turbo sound option.

9P.SIZE

Used to change the screen size.

0DUAL I-II

Used to select the sound mode.

!SOURCE

Used to display all of the available video sources.

@INFO

Used to view the channel information and setting status you selected.

#PRE-CH

Used to switch repeatedly between the last two channels displayed.

$P /

Used to display the next or previous stored channel.

%EXIT

Used to exit from any display or return to normal viewing.

^MUTE

Used to switch the sound off temporarily. To turn the sound back on, press the MUTE, , or button.

&ENTER

While using the onscreen menus, press the ENTER button to activate (or change) a particular item.

*S.MODE

Used to select the sound effect.

(P.MODE

Used to select the picture effect.

)TV

Used to return to the TV mode when it is in external input mode.

aSLEEP

Used to select a preset time interval for automatic turn off.

Installing Batteries

Remove the cover. Install two AAA size batteries, then replace the cover. When the remote control does not operate normally, check that the “+”

and “-” ends of the batteries are inserted correctly or the batteries are drained.

Do not mix battery types, i.e. alkaline and manganese.

Switching theTelevision On and Off

The mains lead is attached to the rear of the television.

1Plug the mains lead into an appropriate socket.

The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.

2Press the “I ” button (On/Off) on the front (or side) of the television.

3Press the POWER button on the remote control to switch the television on. The programme that you were watching last is re-selected automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Channel - Auto Store” or “Channel - Manual Store” on page 4.

If the television is initially powered on, several basic customer settings proceed automatically. Refer to “Setup - Plug & Play” on page 3.

4To switch the television off, press the “I ” button (On/Off) on the front (or side) of the television.

Placing theTelevision in Standby Mode

The television can be placed in standby mode, in order to reduce power consumption and wear of the cathode ray tube. Standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).

1Press the POWER button on the remote control while viewing.

The television is in standby mode.

2To switch the television back on, simply press it again.

Do not leave the television in standby mode for long periods of time (when you are away on holiday, for example). Turn the television off by pressing the “ I ” button (On/Off) on the front (or side) of the television. It is best to unplug the set from the mains and aerial.

English - 2

Check antenna input.

Enjoy your watching

Viewing the Menus

1Press the MENU button.

The main menu is displayed on the screen. Its left side has five icons: Input, Picture, Sound, Channel, and Setup.

2Press the … or † button to select one of the icons. Press the ENTER button to access the icon’s sub-menu.

3Press the … or † button to move to items in the menu. Press the ENTER button to enter items in the menu.

4Press the …/†/œ/√ button to change the selected items. Press the MENU button to return to the previous menu.

5Press the EXIT button to exit from the menu.

Setup - Plug & Play

When the television is initially powered on, several basic customer settings proceed automatically and subsequently. The following settings are available.

1If the television is in standby mode, press the POWER button on the remote control. The Plug & Play is displayed. It flickers for a little while, and then Language menu is displayed.

Plug & Play

Language

English

Français

Türkçe

Move Enter

continued...

2 Select the appropriated

language by pressing the Enter Exit … or † button. Press the

ENTER button.

The Check antenna input. is displayed.

If any language is not selected, the language menu will disappear about 30 seconds later.

3Make sure that the antenna is connected to the television (refer to page 1). Press the ENTER button. The Auto Store menu is displayed with Area selected.

TV	Auto Store
Area	: BelgieASIA W/EUROPE		√
Search	CIS E/EUROPE		√
	CHINA
	HONGKONG	U/K
	AUSTRALIA
	NZ/INDONESIA
	SOUTH AFRICA
	AMERICA
Move	Enter	Return

4Press the ENTER button again.

5Press the … or † button to select your area. Press the ENTER button.

6 To search the channels,	Search
select Search by pressing
the … or † button. Press	Start
the ENTER button.	Enter	Return

7Press the ENTER button again to start search channels. To stop the search, press the ENTER button. When the channel searching has finished, the Time menu is displayed with Clock selected.

8Press the œ or √ button to move to the hour or minute. Set the hour or minute by pressing the … or † button.

Search

	P 1					102MHz
							7 %
			Stop
			Enter				Return
	TV						Time
		Clock		--:--		am
		Sleep	Timer		: Off
		On Timer		--:--		am Off
		Off Timer		--:--		am Off
		On Timer Volume : 10
		Move	Enter				Return

continued...

9 When you have finished, press the MENU button.

The Enjoy your watching is displayed, and then the channel which has been stored will be activated.

Re-setting the Plug & Play	TV				Setup
Method: MENU …/†		Plug	& Play		√
(Setup) ENTER …/†		Language :		English
		Time			√
(Plug & Play) ENTER		Child Lock			√
		Blue	Screen	: Off	√
		Melody		: On	√
		Demonstration			√
	Move		Enter		Return

Input (depending on the model) -

Source List / Edit Name

Source List	TV			Source List
You can switch between		TV
viewing signal from		AV1	----
		AV2	----
connected equipment, such		S-Video	----
as a VCR, DVD, set-top box,		Component ----
and the TV source
(broadcast or cable).	Move		Enter		Return

You can change the required external source simply by pressing the SOURCE button on the remote control. It might take a short period of time for pictures to be switched. To return to the TV mode, press the TV button on the remote control.

Edit Name
	TV			Edit Name
You can give a name to the		AV1	:	Belgie			√
				----
external source.		AV2	:	DVDVCR			√
		S-Video	:	Cable STB			√
		Component	:	Sat. STB
				AV	Recv.
				DVD	Recv.
				Game
				Camcorder
				DVD	Combo
	Move		Enter			Return

English - 3