SMARTPILOT CONTROLLER |
|
|
|
INSTALLATION GUIDE |
|
www.raymarine.com |
|
Parts supplied |
|
|
|
ST6001+ |
ST7001+ or ST8001+ |
|
|
Gasket |
|
Gasket |
|
SmartPilot ST6001 |
|
|
SmartPilot Controller |
Controller |
|
|
(ST8001 shown) |
Sun Cover |
|
Sun Cover |
|
|
|
|
Screw |
|
|
|
(x2 ST6001) |
and / or |
|
|
(x4 ST7/8001) |
|
|
|
|
|
|
Stud |
|
SeaTalk Cables |
|
(x2 ST6001) |
Connector (x2) |
|
|
(x4 ST7/8001) |
|
Tools required |
|
|
|
|
|
5mm (3/16 in) Drill |
|
|
Measure |
|
|
Power Drill |
Pencil |
90 mm (3½ in) Hole Cutter |
|
|
|
|
|
|
|
|
D6354-1 |
Raymarine Ltd, Portsmouth, Hampshire, UK PO3 5TD |
+44 (0) 23 9269 3611 |
|
Raymarine Inc. Nashua, NH 03063-4219, USA |
Toll Free: 800-539-5539 |
-1 |
Recyclable Material - Please dispose of responsibly. |
+1 603-881-5200 |
87014 |
|
||
|
|
|
ST6001 controller template - ST7001 and ST8001 template on reverse
Control Unit: |
|
Drill 5 mm (3/16 in) |
|||
Surface mount template |
TOP |
diameter hole |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Machine hole 90 mm (3.55 in) diameter
Remove shaded areas only
Site requirements |
Check |
Check |
Min 0.8m (2ft 6in) |
Check |
D6355-1 |
2. ST6001 Controller |
Step 1 |
Control |
|
|
Surface Unit: |
|
|
mount |
template |
|
|
TOP
|
|
|
|
|
Drill |
|
|
|
|
|
|
5 |
mm |
|
|
|
|
|
|
|
|
|
|
|
|
diameter(3/16 |
|
|
Machine |
|
|
|
holein) |
|
90 |
mm (3.hole |
|
|
|||
Remove |
|
|
|
|||
|
diameter |
|
|
|
||
|
|
55 |
in) |
|
|
|
|
shaded |
|
|
|
||
|
areas |
|
|
|||
|
|
|
only |
|
||
|
|
|
|
|
|
x2
Drill |
|
5 |
mm |
diameter(3/16 |
|
|
holein) |
x2
Step 2
Sun cover edge
Instrument edge
Drill 5 mm (3/16 in) diameter hole
Control |
|
|
|
|
|
|
|
|
|
Surface Unit: |
|
|
|
|
|
|
|
|
|
|
mount |
template |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TOP |
|
|
Drill5 |
|
|
|
|
|
|
|
|
|
mm |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
diameter(3/16 |
|
|
|
|
|
Machine |
|
|
|
holein) |
|
|
|
|
90 |
mm (3.hole |
|
|
|||
|
|
|
Remove |
|
|
|
|||
|
|
|
|
diameter |
|
|
|
||
inch) |
|
|
|
|
55 |
in) |
|
|
|
|
|
|
shaded |
|
|
|
|||
(3.56 |
|
|
|
areas |
|
|
|||
mm |
|
|
|
|
|
only |
|
||
|
|
|
|
|
|
|
|
||
90.6 |
|
|
|
|
|
|
|
|
|
|
Drill5 |
mm |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
diameter(3/16 |
|
|
|
|
|
|
||
|
|
|
holein) |
|
|
|
|
|
|
D6360-1 |
D6356-1 |