DS600X
Digital Fishfinder
Owner’s Handbook
Document number: 81235-2
Date: April 2004
DS600X Digital Fishfinder |
iii |
This handbook describes the Raymarine DS600X Digital Fishfinder.
Throughout this handbook, the labelled keys are shown in bold capitals; for example, MENU. The software menu names and options are shown in normal capitals; for example, AUTOMATIC.
Operating procedures, which may consist of a single key-press or a sequence of numbered steps, are indicated by a symbol in the margin.
The technical and graphical information contained in this handbook, to the best of our knowledge, was correct as it went to press. However, the Raymarine policy of continuous improvement and updating may change product specifications without prior notice. As a result, unavoidable differences between the product and handbook may occur from time to time, for which liability cannot be accepted by Raymarine.
To register your DS600X Digital Fishfinder ownership, please take a few minutes to fill out the warranty registration card found at the end of this handbook. It is very important that you complete the owner information and return the card to the factory in order to receive full warranty benefits.
iv |
DS600X Digital Fishfinder |
This handbook contains important information on the installation and operation of your new equipment. In order to obtain the best results in operation and performance, please read this handbook thoroughly.
Raymarine’s Product Support representatives, or your authorized dealer, are available to answer any questions you may have.
Raymarine DS600X Digital Fishfinders are intended for recreational fishfinding.
All Raymarine equipment and accessories are designed to the best industry standards for use in the recreational marine environment.
Their design and manufacture conforms to the appropriate Electromagnetic Compatibility (EMC) standards, but correct installation is required to ensure that performance is not compromised. Although every effort has been taken to ensure that they will perform under all conditions, it is important to understand what factors could affect the operation of the product.
The guidelines given here describe the conditions for optimum EMC performance, but it is recognized that it may not be possible to meet all of these conditions in all situations. To ensure the best possible conditions for EMC performance within the constraints imposed by any location, always ensure the maximum separation possible between different items of electrical equipment.
For optimum EMC performance, it is recommended that wherever possible:
•Raymarine equipment and cables connected to it are:
•At least 3 ft (1 m) from any equipment transmitting or cables carrying radio signals, e.g., VHF radios, cables and antennas.
•More than 7 ft (2 m) from the path of a radar beam. A radar beam can normally be assumed to spread 20 degrees above and below the radiating element.
DS600X Digital Fishfinder |
v |
•Raymarine specified cables are used. Cutting and rejoining these cables can compromise EMC performance and must be avoided unless doing so is detailed in the installation manual.
•If a suppression ferrite is attached to a cable, this ferrite should not be removed. If the ferrite needs to be removed during installation it must be reassembled in the same position.
1.PRODUCT INSTALLATION. This equipment must be installed and operated in accordance with the instructions contained in this handbook. Failure to do so could result in poor product performance, personal injury and/or damage to your boat.
2.HIGH VOLTAGE. The display unit, transducer cable, and transducer
contain high voltages. Adjustments require specialized service procedures and tools only available to qualified service technicians - there are no user serviceable parts or adjustments.
3.NAVIGATION AID. This unit is only an aid to navigation. Its accuracy can be affected by many factors, including equipment failure or defects, environmental conditions, and improper handling or use. It is the user’s responsibility to exercise common prudence and navigational judgments. This fishfinder should not be relied upon as a substitute for such prudence and judgment.
4.ULTRASONIC ENERGY. The transducer transmits high frequency energy while in use. The unit should be turned off when swimmers or divers are in close proximity to the transducer. (There is a lack of scientifically sound standards or guidelines for exposure levels and limits to ultrasound. This notice is precautionary only.)
WARNING:
Do not disconnect the transducer cable without first powering off the display unit. Removal of the transducer cable from the DS600X while power is turned on can cause sparks.
Mount unit where it is well ventilated and free from gasoline fumes.
vi |
DS600X Digital Fishfinder |
Raymarine products are supported by a network of Authorized Service Representatives. Raymarine’s Technical Services representatives or your local dealer will be available to answer any questions you may have. For information on Raymarine products and services, contact either of the following:
United States |
Raymarine, Incorporated |
|
|
22 Cotton Road, Unit D |
|
|
Nashua, New Hampshire |
|
|
03063-4219 USA |
|
|
Telephone:1-603-881-5200 |
|
|
|
1-800-539-5539 |
|
Fax: |
1-603-864-4756 |
Europe |
Raymarine Limited |
|
|
Anchorage Park |
|
|
Portsmouth, Hampshire |
|
|
PO3 5TD England |
|
|
Telephone: +44 (0) 23 9269 3611 |
|
|
Fax: |
+44 (0) 23 9269 4642 |
Or, you may contact us on the World Wide Web at:
www.raymarine.com
© Raymarine Limited 2004
|
|
vii |
Contents |
|
|
Preface ................................................................................................................... |
|
iii |
Conventions Used ................................................................................... |
iii |
|
Technical Accuracy ................................................................................. |
iii |
|
Warranty .................................................................................................. |
iii |
|
Important Information ........................................................................................ |
iv |
|
Intended Use ............................................................................................ |
iv |
|
EMC Conformance ................................................................................. |
iv |
|
Safety Notices ........................................................................................... |
v |
|
Raymarine Products and Services ........................................................... |
vi |
|
Chapter 1: Overview ............................................................................................ |
1 |
|
1.1 |
Introduction ...................................................................................... |
1 |
|
Features ......................................................................................... |
2 |
|
General .......................................................................................... |
3 |
|
Transducer .............................................................................. |
3 |
Chapter 2: Installation ......................................................................................... |
5 |
|
2.1 |
Introduction ...................................................................................... |
5 |
2.2 |
Unpacking and Inspecting the Components ..................................... |
5 |
2.3 |
Selecting the Equipment Location ................................................... |
6 |
|
Mounting Location ....................................................................... |
6 |
2.4 |
Cable Runs ....................................................................................... |
7 |
2.5 |
Mounting the Fishfinder ................................................................... |
9 |
|
Bracket Mounting ......................................................................... |
9 |
|
Console Mounting (optional) ....................................................... |
9 |
2.6 |
System Connections ....................................................................... |
11 |
|
DC Power and NMEA Connection ............................................. |
11 |
|
Transducer Connection ............................................................... |
13 |
Chapter 3: Getting Started ................................................................................ |
15 |
|
3.1 |
Introduction .................................................................................... |
15 |
3.2 |
Powering on the Fishfinder ............................................................ |
15 |
3.3 |
Simulator Mode .............................................................................. |
15 |
3.4 |
LCD Display .................................................................................. |
16 |
3.5 |
Interpreting the Sounder Image ...................................................... |
17 |
|
Target Indications ....................................................................... |
18 |
3.6 |
Keypad Operation .......................................................................... |
19 |
3.7 |
Using the Variable Range Marker (VRM) ..................................... |
20 |
3.8 |
Selecting the Display Page ............................................................. |
21 |
3.9 |
Menu Operation ............................................................................. |
23 |
|
Menu Structure ........................................................................... |
23 |
viii |
|
DS600 Digital Fishfinder |
|
Chapter 4: Main Menu ....................................................................................... |
|
25 |
|
4.1 |
Introduction .................................................................................... |
|
25 |
|
Selecting MENU Items ............................................................... |
|
25 |
4.2 |
Fishfinder Operation Controls ........................................................ |
|
29 |
|
Scroll Speed ................................................................................ |
|
30 |
|
Range .......................................................................................... |
|
30 |
|
Frequency ................................................................................... |
|
32 |
|
A-Scope ...................................................................................... |
|
33 |
|
GAIN MODE... .......................................................................... |
|
34 |
|
GAIN .................................................................................... |
|
35 |
|
Color Gain ............................................................................. |
|
35 |
|
Time Variable Gain (TVG) ................................................... |
|
36 |
|
Sounder Interference Rejection (Int. Rej.) ............................ |
36 |
|
|
Second Echo Rejection ......................................................... |
|
37 |
|
Power .................................................................................... |
|
37 |
|
Max. Ping Rate ...................................................................... |
|
37 |
|
ZOOM... ..................................................................................... |
|
37 |
|
View ...................................................................................... |
|
38 |
|
Zoom x2, x3, x4 Magnification ............................................. |
|
39 |
|
Mode ..................................................................................... |
|
39 |
|
TRIP RESET... ............................................................................ |
|
39 |
|
DISPLAY SET UP... ................................................................... |
|
39 |
|
SOUNDER SET UP... ................................................................. |
|
39 |
Chapter 5: Display Set Up .................................................................................. |
|
41 |
|
5.1 |
Introduction .................................................................................... |
|
41 |
|
Brightness ................................................................................... |
|
44 |
|
Target Depth ID .......................................................................... |
|
44 |
|
Depth Digit Size .......................................................................... |
|
45 |
|
Transparent Menu ....................................................................... |
|
45 |
|
PALETTE... ................................................................................ |
|
46 |
|
Selection ............................................................................... |
|
46 |
|
Background Color ................................................................. |
|
47 |
|
DATA ITEMS... .......................................................................... |
|
47 |
|
NAV. SET UP... (Navigation Data) ............................................. |
|
48 |
Chapter 6: Sounder Set Up ................................................................................ |
|
51 |
|
6.1 |
Introduction .................................................................................... |
|
51 |
|
ALARMS... ................................................................................ |
|
55 |
|
Target Depth ID ..................................................................... |
|
55 |
|
Fish Alarm ............................................................................ |
|
56 |
|
Shallow Alarm ...................................................................... |
|
56 |
|
Shallow Range ...................................................................... |
|
56 |
|
Deep Alarm ........................................................................... |
|
57 |
|
|
ix |
|
Deep Range ........................................................................... |
57 |
|
Temp. Alarm ......................................................................... |
57 |
|
Temp. Rng. High ................................................................... |
58 |
|
Temp. Rng. Low ................................................................... |
58 |
|
ALARM CLOCK... .............................................................. |
58 |
|
UNITS... ..................................................................................... |
59 |
|
Depth Units ........................................................................... |
59 |
|
Temp. Units ........................................................................... |
59 |
|
Speed Units ........................................................................... |
59 |
|
Distance Units ....................................................................... |
59 |
|
Bearing Mode ....................................................................... |
60 |
|
Date Format .......................................................................... |
60 |
|
Time Format .......................................................................... |
60 |
|
NMEA-OUT SET UP... .............................................................. |
60 |
|
Language .................................................................................... |
61 |
|
Key Beep .................................................................................... |
61 |
|
Key Help ..................................................................................... |
61 |
|
Depth Offset ................................................................................ |
62 |
|
Speed Calibrate ........................................................................... |
62 |
|
Temp Calibrate ............................................................................ |
62 |
|
Sounder Simulator ...................................................................... |
62 |
|
SW Version and Serial Number (read only) ................................ |
62 |
Chapter 7: Maintenance and Problem Solving ............................................... |
63 |
|
7.1 |
Maintenance ................................................................................... |
63 |
|
Routine Checks ........................................................................... |
63 |
|
Cleaning Instructions .................................................................. |
63 |
|
Cleaning the Unit .................................................................. |
63 |
|
Cleaning the Transducer ....................................................... |
63 |
|
Cleaning the Hull .................................................................. |
64 |
|
EMC Servicing and Safety Guidelines ....................................... |
64 |
7.2 |
Problem Solving ............................................................................. |
65 |
|
Common Problems and Their Solutions ..................................... |
65 |
7.3 How to Contact Raymarine ............................................................ |
66 |
|
|
On the Internet ............................................................................ |
66 |
|
Customer Support ................................................................. |
66 |
|
In the US ..................................................................................... |
66 |
|
Accessories and Parts ............................................................ |
66 |
|
Technical Support ................................................................. |
67 |
|
Product Repair and Service ................................................... |
67 |
|
In Europe ..................................................................................... |
68 |
|
Technical Support ................................................................. |
68 |
|
Accessories and Parts ............................................................ |
68 |
x |
DS600 Digital Fishfinder |
Worldwide Support |
..................................................................... 68 |
Appendix A: Specifications ................................................................................ |
69 |
Index ...................................................................................................................... |
71 |
Chapter 1: Overview |
1 |
Chapter 1: Overview
This handbook describes the DS600X Digital Fishfinder. The DS600X features state-of-the-art High Definition Fish Imaging (HDFI) technology. Constantly adjusting transmitter and receiver parameters throughout the water column, the DS600X intelligently analyzes fish and bottom echoes and automatically produces a crystal clear echo sounder display.
D6454-1
Figure 1-1: DS600X Digital Fishfinder
The DS600X employs a very high transmission repetition or “ping” rate which, along with the digital adaptive high sample rate receiver, ensures that fish and bottom structure are presented in superb detail and optimal color allocation. The DS600X digital bandwidth adaptation adjusts the receiver band width dynamically from very wide to very narrow, as required by the actual water conditions. This provides superior fish and bottom detection in all water conditions.
2 |
DS600X Digital Fishfinder |
|
|
•5.7" Transmissive High Brightness TFT Color LCD
•¼ VGA 76,800 Pixel Display Resolution
•Patented Digital HDFI Technology
•Hands-Off Adaptive Auto Adjustments
•Dual Frequency 200/50 kHz 500W RMS
•Depth/Temp/Speed transducer included with some models, which can measure water depth, water temperature and speed
•Speedometer-style digital data screen overlay
•NMEA 0183 compliant
•Easy Bracket or Flush mounting
•Waterproof to IPX7
D6458-1
Fishfinder
Transducer
Figure 1-2: Basic Fishfinder System using the DS600X
Chapter 1: Overview |
3 |
The DS600X system, illustrated below, is comprised of the digital fishfinder, transducer and associated cables.
The DS600X is waterproof to IPX7 and can be installed either above or below deck.
The unit includes connections to:
•Power/NMEA
•the transducer
The DS600X requires a transducer for measuring water depth, water temperature, distance traveled, and speed. A transducer is included with some fishfinder models. It is important to position your transducer correctly. Details on your transducer, including location and installation instructions, are included in the transducer box.
4 |
DS600X Digital Fishfinder |
|
|
Chapter 2: Installation |
5 |
Chapter 2: Installation
This chapter provides installation instructions for your DS600X.
Note: If you wish to practice using the unit before installation, connect the power cable and use the simulator mode as described in Chapter 3. For power, connect a 12VDC power supply, attaching the red wire to positive and the black wire to negative. See Section 3.3 for details.
Unpack your system carefully, to prevent damage to the equipment. Save the carton and packing, in case you need to return a unit for service.
Check that you have all the correct system components. These depend on your system package, as follows:
:
Table 2-1: Supplied Parts
Item |
Part No. |
|
|
One of the following units: |
|
DS600X Digital Fishfinder without Transducer, US version |
E63065 |
DS600X Digital Fishfinder without Transducer, CE version |
E63066 |
|
|
Sun Cover |
E32050 |
|
|
Mounting Bracket |
E35005 |
|
|
Mounting Bracket Knobs |
W145 |
|
|
Power/NMEA cable |
R69074 |
|
|
Handbook, DS600X |
81235 |
|
|
Mounting hardware |
N/A |
|
|
The following accessories are available for your A Series Fishfinder:
Table 2-2: Optional Accessories
Item |
Part No. |
|
|
Flush Mount Kit |
E32051 |
|
|
6 |
DS600X Digital Fishfinder |
Transducers are supplied with some models and optional with others. The following transducer options are available:
:
Table 2-3: Transducer Parts
Item |
Part No. |
|
|
Transducer Adapter Cable for L365/L470 Style Transducers |
E66070 |
|
|
Transducer Adapter Cable for hsb2/DSM250 Style Transducers |
E66066 |
|
|
Transom Mount Transducer for DS400X/DS500X/DS600X (P58)1 |
E66062 |
|
|
Bronze Thru-hull Transducer for DS400X/DS500X/DS600X (B744V)1 |
E66061 |
1supplied with some models
The DS600X is waterproof to IPX7 is and designed to be mounted either above or below deck. The unit should be protected from physical damage and excessive vibration.
When planning the installation, the following should be considered to ensure reliable and trouble free operation:
•Access: There must be sufficient space below the unit to enable cable connections to the panel connectors, avoiding tight bends in the cable.
•Interference: The selected location should be far enough away from devices that may cause interference, such as motors, generators, and radio transmitter/receivers. (See the EMC guidelines in the Preface.)
•Magnetic compass: Mount the unit at least 3 ft (1m) away from a magnetic compass.
•Cable runs: The unit must be located near a DC power source. The power cable supplied is 5 ft (1.5 m), but a longer cable can be used if desired. Refer to Section 2.4.
The maximum length of cable between the fishfinder and the transducer unit should not normally exceed 25 ft (8 m).
•Environment: Good ventilation is required to prevent overheating.
Chapter 2: Installation |
7 |
WARNING:
Consider the following before installing the system cables:
•You will need to attach the power and transducer cables to the rear of the unit.
•All cables should be adequately secured, protected from physical damage and exposure to heat.
•Avoid running cables through bilges or doorways, or close to moving or hot objects.
•Avoid sharp bends.
•Where a cable passes through an exposed bulkhead or deckhead, use a watertight feed-through.
•Secure cables in place using tie-wraps or lacing twine. Coil any extra cable and tie it out of the way.
You will need to run the following cables:
•Power/NMEA cable, supplied with the unit. This 5 ft (1.5 m) cable has a connector plug at one end for connecting to the fishfinder, and 3 wires at the other end for connecting the power supply. The power cable may be extended by up to 60 ft (20 m) using a wire gauge of AWG 12 or greater. The DS600X is intended for use on the boat’s DC power systems rated from 10-18 Volts DC (13.8V nominal).
•Transducer cable, supplied with the transducer. This 25 ft (8 m) cable has a connector plug at one end for the display unit.
•Do not cut the transducer cable or remove the connector.
•Do not shorten or splice the cable.
If the transducer cable is cut, it must be replaced—it cannot be repaired. Cutting the cable will also void the warranty.
8 |
DS600X Digital Fishfinder |
5.08in (129 mm)
7.00in (178 mm)
1.38 in 1.38 in
(35 mm) (35 mm)
Figure 2-1:
6.93 in (176 mm) |
7.48 in (190 mm) |
3.74 in (95 mm)
1.26 in (32 mm)
1.57 in
(39.9 mm)
2.52in (64 mm)
5.12in (130 mm) plug clearance
5.28 in (134 mm)
D6455-1
4.72 in (120 mm)
DS600X Unit Dimensions
Chapter 2: Installation |
9 |
The DS600X can be mounted on a dash, chart table, bulkhead or deckhead using the supplied hardware. The unit can also be flush mounted directly into the console.
The fishfinder may also be installed directly into the console. This requires the purchase of an optional Flush Mount kit, Raymarine part number E32051.
2.Check the selected location for the unit. A clear, flat area at least 7¼" (184 mm) wide by 7¼" (184 mm) high, with at least 3½" (89 mm) of clearance behind the panel, is required.
4.Drill a ½ in (12.7 mm) pilot hole in each corner of the cut-out area.
5.Using a suitable saw, cut along the inside edge of the cut-out line.
6.Remove the mounting bracket knobs and bracket from the unit. Make sure that the unit fits in the cut-out area.
10 |
DS600X Digital Fishfinder |
11.Slide the unit into the panel cut-out.
20.02˚ and -35.02˚ |
D6645-1 |
Figure 2-2: DS600X Flush Mounting Arrangement
Chapter 2: Installation |
11 |
The rear of the fishfinder provides the following connection sockets:
•Power/NMEA
•Transducer
D6460-2
Power/NMEA Transducer
Figure 2-3: DS600X Connector Panel
The DS600X is intended for use on boat’s DC power systems rated from 1018 Volts DC (13.8V nominal).
A 5 ft (1.5 m) cable is supplied for connecting the boat’s DC power and NMEA interface to the unit. This Power/NMEA cable can be extended by up to 60 ft (20 m) using a wire gauge of AWG 12 or greater.
The cable’s molded end attaches to the seven-pin Power/NMEA connector on the unit’s connector panel.
The cable connector (viewed from the outside) is shown in the following drawing.
pin1
D6462-2
Figure 2-4: Power Cable Connector
The exposed wires on the open end of the cable should be connected as follows:
12 |
|
|
DS600X Digital Fishfinder |
|
|
|
|
|
|
|
Pin No. |
Function |
Color |
|
|
|
|
|
|
1 |
Battery negative – |
Black |
||
|
|
|
|
|
2 |
Battery positive + (10.0VDC to 18.0VDC) |
Red |
||
|
|
|
|
|
3 |
NMEA Input + |
White |
||
|
|
|
|
|
4 |
NMEA Input – |
Green |
||
|
|
|
|
|
5 |
CGND |
Gray |
||
|
|
|
|
|
6 |
NMEA Output + |
Yellow |
||
|
|
|
|
|
7 |
NMEA Output – |
Brown |
||
|
|
|
|
|
The red wire connects to the feed from the positive (+) battery terminal and the black wire connects to the feed from the negative (–) battery terminal. The shield wire (drain) connects to the boat’s RF ground. If your boat does not have an RF system, you can trim off the drain wire.
A fast blow 2 amp fuse is attached (in-line) to the red (positive) wire.
D6891-1
Figure 2-5: Installing the Fuse
Chapter 2: Installation |
13 |
A 25ft (8m) cable is supplied with the transducer. The transducer cable connector has a nut that has been removed to aid installation. To enable you to complete the installation without cutting the cable, ensure that any holes you drill are large enough to accept the connector, with the nut removed (approximately 13/16" or 21 mm).
Before attaching the transducer cable, you will need to attach the connector nut, which is included in the transducer packaging.
The transducer cable is attached to the 7 pin male TRANSDUCER connector on the connector panel of the DS600X. (See Figure 2-3 .)
•Do not pull on the cable. This can damage the transducer wires.
•Do not cut the transducer cable or remove the connector.
•Do not try to shorten or splice the cable. Cutting the transducer cable will severely reduce sonar performance.
•If the cable is cut, it must be replaced—it cannot be repaired. Cutting the cable will also void the warranty.
WARNING:
If the transducer cable is accidentally removed while the DS600X is powered on, remove power from the fishfinder, replace the transducer cable, and then restore power. As a safety feature, the DS600X only recognizes that the transducer is connected at power-up.
14 |
DS600X Digital Fishfinder |
Chapter 3: Getting Started |
15 |
Chapter 3: Getting Started
This chapter provides basic instructions to get you started using the DS600X Digital Fishfinder. It describes Simulator mode and can help you to become familiar with the basic functions of the fishfinder’s operation controls. More detailed information on using the menu items and display controls is provided in Chapter 4 and Chapter 5, respectively.
Connect the power cord to boat’s power source and plug into the power port
POWER |
on the connector panel. Press the POWER button on the DS600X. |
|
|
|
Details on setting up your DS600X and display are given in Chapter 6. |
If you have not fully installed the fishfinder, you can still operate in Simulator mode by connecting the fishfinder to a 12VDC power supply.
Figure 3-1 demonstrates how to setup the DS600X for Simulator mode. Attach the red wire from the power lead to positive (+) and the black wire to negative (–).
When you power up the DS600X without connecting the transducer, the unit enters Demo mode. This provides a preprogrammed demonstration highlighting the fishfinder’s main features. This function enables you to practice operating the fishfinder without data from the transducer, using simulated data.
If the transducer is connected, you can enter Simulator Mode by following instructions outlined on page 62.
16 |
DS600X Digital Fishfinder |
Fishfinder |
Red |
Black |
DC Volts
D6646-1
Figure 3-1: Demo/Simulator Mode Setup
When you first switch on the fishfinder, the scrolling bottom graph, or Fishfinder Page, is displayed. This is a graphical representation of the echoes seen by the DS600X. As time passes, this display scrolls from right to left and becomes a record of the echoes seen. A typical display is shown in Figure 3- 2 .
The images at the right hand side of the display are the most recent echoes. Some echoes indicate fish, and others show the bottom. It can also indicate bottom structures, such as a reef or shipwreck. The upper and lower depth range limits are shown.
You can customize the sounder by choosing what is displayed and how it is displayed (including language and units). For example, you can set whether the bottom graph display scrolls and you can select the range to adjust the depth displayed.
You can view the cursor position and a variety of data (such as speed and depth) from the transducer and other equipment in user-selectable data boxes. These data boxes can be moved around the screen and they can be switched on or off.
Chapter 5 includes details on adjusting the display, other set up options are described in Chapter 6.