Philips GC4444, GC4440, GC4430, GC4425, GC4422 User Manual [ar]

Steam Iron

GC4444, GC4440, GC4430, GC4425, GC4422, GC4420, GC4415, GC4412, GC4411, GC4410

1

English 6 Français 19 43

55

GC4444, GC4440, GC4430, GC4425, GC4422,

GC4420, GC4415, GC4412, GC4411, GC4410

English

Introduction

Congratulations on your purchase and welcome to Philips!To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome.

General description (Fig. 1)

ASpray nozzle

BCap of filling opening

CSteam boost

DSpray button

ESteam control

FIonic DeepSteam button (GC4444, GC4440, GC4430)

GIonic DeepSteam light (GC4444, GC4440, GC4430)

HTemperature dial

IGC4425, GC4422, GC4420, GC4412: Amber temperature light with red automatic shut-off (AUTO/OFF) indication. GC4415, GC4411, GC4410: Amber temperature light

JGC4444, GC4440, GC4430: Amber temperature light with red automatic shut-off (AUTO/OFF) indication

KMains cord

LType plate

MSoleplate

NCalc-Clean button

Not shown: Heat-resistant protective cover (GC4444, GC4440 only) Not shown: Delicate fabric protector (GC4425, GC4415 only)

Important

Read this user manual carefully before you use the appliance and save it for future reference.

Danger

-Never immerse the iron in water.

Warning

-Check if the voltage indicated on the type plate corresponds to the local mains voltage before you connect the appliance.

English

-Do not use the appliance if the plug, the mains cord or the appliance itself shows visible damage, or if the appliance has been dropped

or leaks.

-If the mains cord is damaged, you must have it replaced by Philips, a service centre authorised by Philips or similarly qualified persons in order to avoid a hazard.

-Never leave the appliance unattended when it is connected to the mains.

-This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

-Children should be supervised to ensure that they do not play with the appliance.

-Do not let the mains cord come into contact with the hot soleplate of the iron.

Caution

-Check the mains cord regularly for possible damage.

-The soleplate of the iron can become extremely hot and may cause burns if touched.

-When you have finished ironing, when you clean the appliance, when you fill or empty the water tank and also when you leave the iron even for a short while: set the steam control to position 0, put the iron on its heel and remove the mains plug from the wall socket.

-Always place and use the iron on a stable, level and horizontal surface.

-Do not put perfume, vinegar, starch, descaling agents, ironing aids or other chemicals in the water tank.

-This appliance is intended for household use only.

Electromagnetic fields (EMF)

This Philips appliance complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user manual, the appliance is safe to use based on scientific evidence available today.

English

Before first use

1Remove any sticker, protective foil or plastic from the soleplate.

2Rinse and dry the filling cup.

Preparing for use

Filling the water tank

1Make sure the appliance is unplugged.

2Set the steam control to position 0 (= no steam) (Fig.2).

3Open the cap of the filling opening.

4Tilt the iron backwards and use the filling cup to fill the water tank with tap water up to the maximum. (Fig.3)

Do not fill the water tank beyond the MAX indication.

Do not put perfume,vinegar, starch, descaling agents,ironing aids or other chemicals in the water tank.

,If the tap water in your area is very hard,we advise you to mix it with an equal portion of distilled water, or to use distilled water only.

5Close the cap of the filling opening (‘click’) (Fig. 4).

Setting the temperature

1GC4444, GC4440 only: Remove the heat-resistant protective cover (Fig.5).

Do not leave the heat-resistant protective cover on the soleplate during ironing.

2Put the iron on its heel.

3To set the required ironing temperature, turn the temperature dial to the appropriate position (Fig.6).

Check the laundry care label for the required ironing temperature:

-1 for synthetic fabrics (e.g. acrylic, nylon, polyamide, polyester)

- 1

for silk

English

-2 for wool

-3 for cotton

-MAX for linen

If you do not know what kind or kinds of fabric an article is made of, determine the right ironing temperature by ironing a part that will not be visible when you wear or use the article.

Silk, woollen and synthetic materials: iron the reverse side of the fabric to prevent shiny patches.To prevent stains, do not use the spray function. Start ironing the articles that require the lowest ironing temperature, such as those made of synthetic fibres.

4Put the mains plug in a wall socket.

,The amber temperature light goes on.

5When the amber temperature light has gone out, wait a while before you start ironing.

The temperature light goes on from time to time during ironing.

Using the appliance

Note:The iron may give off some smoke when you use it for the first time. This stops after a short while.

Steam ironing

1Make sure that there is enough water in the water tank.

2Set the required ironing temperature (see chapter‘Preparing for use’,section‘Setting the temperature).

3Set the appropriate steam setting.Make sure that the steam setting

you select is suitable for the set ironing temperature: (Fig.7)

-1 - 3 for moderate steam (temperature settings 2to 3)

-4 - 6 for strong steam (temperature settings 3to MAX)

Note:The iron starts to produce steam as soon as it reaches the set temperature.

Note: If the set ironing temperature is too low (MIN to 2), water may drip from the soleplate (see chapter‘Features,section‘Drip stop’).

10 English

Ironing with Ionic DeepSteam (GC4444, GC4440, GC4430 only)

When you use the Ionic DeepSteam function during steam ironing, the steam produced is finer than during regular steam ironing. Fine steam reaches deeper, especially into thick fabrics.This helps you to remove stubborn creases easily.

1Follow steps 1 to 3 in section‘Steam ironing’.

2Press and hold the Ionic DeepSteam button (Fig.8).

,The Ionic DeepSteam light goes on and you hear a humming sound (Fig. 9).

3The iron now produces Ionic DeepSteam to help you remove even the toughest creases.

Note:The Ionic DeepSteam function is only effective when it is used in combination with a steam setting and a temperature setting between 2 and MAX.

Note: Do not use the Ionic DeepSteam function when you iron without steam and/or at low temperature settings.However,ironing at low temperatures without steam with the Ionic DeepSteam function switched on will not damage the iron.

Note:The Ionic DeepSteam output may vary from time to time, depending on the ironing temperature.

Ironing without steam

1 Set the steam control to position 0 (= no steam) (Fig.2).

Do not use the Ionic DeepSteam function,as this function has no effect when you iron without steam.

2Set the required ironing temperature (see chapter‘Preparing for use’,section‘Setting the temperature’).

After ironing

1 Remove the mains plug from the wall socket.

English 11

2If you have been steam ironing,empty the water tank.

3Let the iron cool down in a safe place.

Features

Spray function

You can use the spray function at any temperature to moisten the article to be ironed.This helps remove stubborn creases.

1Make sure that there is enough water in the water tank.

2Press the spray button several times to moisten the article to be ironed (Fig.10).

Steam boost function

A steam boost from the special Steam Tip soleplate helps remove stubborn creases.The steam boost enhances the distribution of steam into every part of your garment.

The steam boost function can only be used at temperature settings between 3and MAX.

1Press and release the steam boost button (Fig.11).

Vertical steam boost

1You can also use the steam boost function when you hold the iron in vertical position (Fig.12).

This is useful for removing creases from hanging clothes, curtains etc.

Never direct the steam at people.

Drip stop

This iron is equipped with a drip-stop function: the iron automatically stops producing steam when the temperature is too low, to prevent water from dripping out of the soleplate.When this happens, you may hear a sound.

12 English

Automatic shut-off function (GC4444, GC4440, GC4430, GC4425, GC4422, GC4420, GC4412 only)

The automatic shut-off function automatically switches off the iron if it has not been moved for a while.

,The redAUTO/OFF indication of the temperature light flashes to indicate that the iron has been switched off by the automatic shutoff function.

To let the iron heat up again:

1Pick up the iron or move it slightly.

,The redAUTO/OFF indication goes out.

,If the temperature of the soleplate has dropped below the set ironing temperature, the amber temperature light goes on.

2If the amber temperature light goes on after you have moved the iron,wait for it to go out before you start ironing.

Note: If the amber temperature light does not go on after you move the iron, the soleplate still has the right temperature and the iron is ready for use.

Delicate fabric protector (GC4425, GC4415 only)

The delicate fabric protector protects delicate fabrics from heat damage and shiny patches.

With the delicate fabric protector you can iron delicate fabrics (silk, wool and nylon) at temperature settings 3to MAX in combination with all steam functions available on the iron.

The delicate fabric protector reduces the soleplate temperature instantly, thus allowing you to iron delicate fabrics safely.

If you do not know what kind or kinds of fabric an article is made of, determine the right ironing temperature by ironing a part that will not be visible when you wear or use the article.

1 Put the iron on the delicate fabric protector (‘click’) (Fig. 13).

English 13

Cleaning and maintenance

Cleaning

1Wipe flakes and any other deposits off the soleplate with a damp cloth and a non-abrasive (liquid) cleaning agent.

To keep the soleplate smooth, avoid hard contact with metal objects.

Never use a scouring pad,vinegar or other chemicals to clean the soleplate.

2Clean the upper part of the iron with a damp cloth.

3Regularly rinse the water tank with water. Empty the water tank after you have rinsed it.

Double-Active Calc System

The Double-Active Calc System consists of an Anti-Calc tablet inside the water tank combined with the Calc-Clean function.

1The Anti-Calc tablet prevents scale from clogging the steam vents. This tablet is constantly active and does not need to be replaced.

2The Calc-Clean function removes the scale particles from the iron.

Using the Calc-Clean function

Use the Calc-Clean function once every two weeks. If the water in your area is very hard (i.e. when flakes come out of the soleplate during ironing), use the Calc-Clean function more frequently.

1Make sure the appliance is unplugged.

2Set the steam control to position 0.

3Fill the water tank to the maximum level.

Do not put vinegar or other descaling agents in the water tank.

4Set the temperature dial to MAX (Fig. 14).

5Put the plug in a wall socket.

6Unplug the iron when the temperature light goes out.

14 English

7Hold the iron over the sink,press and hold the Calc-Clean button and gently shake the iron to and fro (Fig.15).

,Steam and boiling water come out of the soleplate.Impurities and flakes (if any) are flushed out.

8Release the Calc-Clean button as soon as all the water in the tank has been used up.

Repeat the Calc-Clean process if the iron still contains a lot of impurities.

After the Calc-Clean process

1Put the plug back into the wall socket and let the iron heat up to let the soleplate dry.

2Unplug the iron when it has reached the set ironing temperature.

3Move the hot iron gently over a piece of used cloth to remove any water stains that may have formed on the soleplate.

4Let the iron cool down before you store it.

Storage

1Set the steam control to position 0 and unplug the iron.

2Empty the water tank (Fig.16).

3Let the iron cool down in a safe place.

4Wind the mains cord and fix it with the cord binder (Fig.17).

5Store the iron on its heel on a stable surface.

Heat-resistant protective cover (GC4444, GC4440 only)

You can store the iron on the heat-resistant protective cover immediately after ironing. It is not necessary to let the iron cool down first.

Do not use the heat-resistant protective cover during ironing.

1Put the iron on the heat-resistant protective cover (Fig. 18).

2Insert the tip of the soleplate into the heat-resistant protective cover (1) and then press down the heel of the iron (2).

English 15

Environment

-Do not throw away the appliance with the normal household waste at the end of its life, but hand it in at an official collection point for recycling. By doing this, you help to preserve the

environment (Fig. 19).

Guarantee & service

If you need information or if you have a problem, please visit the Philips website at www.philips.com or contact the Philips Customer Care

Centre in your country (you find its phone number in the worldwide guarantee leaflet). If there is no Customer Care Centre in your country, go to your local Philips dealer or contact the Service Department of Philips Domestic Appliances and Personal Care BV.

Troubleshooting

If the appliance does not work or does not work properly, first check the list below. If the problem is not mentioned in this list, the appliance

Problem	Possible cause	Solution
The iron is	There is a	Check the mains cord, the plug
plugged in,	connection	and the wall socket.
but the	problem.
soleplate is
cold.
	The temperature	Set the temperature dial to the
	dial is set to MIN.	required position.
The iron	There is not	Fill the water tank (see chapter
does not	enough water in	‘Preparing for use’, section ‘Filling
produce any	the water tank.	the water tank’).
steam.

16 English

Problem	Possible cause	Solution
	The steam control	Set the steam control to a
	is set to position 0.	position between 1 and 6 (see
		chapter ‘Using the appliance’,
		section ‘Steam ironing’).
	The iron is not hot	Set an ironing temperature that is
	enough and/or the	suitable for steam ironing (2to
	drip-stop function	MAX). Put the iron on its heel
	has been activated.	and wait until the temperature
		light has gone out before you
		start ironing.
The iron	You have used the	Continue ironing in horizontal
does not	steam boost	position and wait a while before
produce a	function too often	you use the steam boost function
steam boost.	within a very short	again.
	period.
	The iron is not hot	Set an ironing temperature at
	enough.	which the steam boost function
		can be used (3to MAX). Put
		the iron on its heel and wait until
		the temperature light has gone
		out before you use the steam
		boost function.

Water	You have not
droplets drip	closed the cap of
onto the	the filling opening
fabric during	properly.
ironing.

Press the cap until you hear a click.

You have put an additive in the water tank.

Rinse the water tank and do not put any additive in the water tank.

English 17

Problem	Possible cause	Solution
	The set	Set a temperature of or 2
	temperature is too
		higher.
	low for steam
	ironing.
	You have used the	Set the temperature dial to a
	steam boost	setting between 3and MAX.
	function at a
	temperature setting
	below 3.
Water drips	You have put the	Empty the water tank.
from the	iron in horizontal
soleplate	position with water
after the	still left in the water
iron has	tank.
cooled
down or has
been stored.
Flakes and	Hard water forms	Use the Calc-Clean function one
impurities	flakes inside the	or more times (see chapter
come out of	soleplate.	‘Cleaning and maintenance’,
the soleplate		section ‘Using the Calc-Clean
during		function’).
ironing.

18 English

Problem	Possible cause	Solution
The red light	The automatic	Move the iron slightly to
flashes	shut-off function	deactivate the automatic shut-off
(GC4444,	has switched off	function.The red AUTO/OFF light
GC4440,	the iron (see	goes out.
GC4430,	chapter ‘Features’,
GC4425,	section ‘Automatic
GC4422,	shut-off function’).
GC4420,
GC4412
only).

The iron	The Ionic
makes a	DeepSteam
humming	function is on.
sound.

If you hear the humming sound when you iron without steam, stop pressing the Ionic DeepSteam button.The Ionic DeepSteam function has no effect when you iron without steam.