TWK86103GB
TWK86104GB
en Operating instructions de Gebrauchsanweisung
TWK861.indd 1 |
30.08.2011 16:45:17 |
en |
English |
2 |
|
|
|
de |
Deutsch |
5 |
|
|
|
TWK861.indd 2 |
30.08.2011 16:45:17 |
2 |
3 |
5 |
6 |
7 
4
8
1
10
9
|
|
|
a |
b |
max.
|
|
|
|
|
|
c |
d |
||||
|
|
e |
|
|
|
|
|
|
|
f |
|
|
|
g |
h |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TWK861.indd 3 |
30.08.2011 16:45:18 |
2
Congratulations on purchasing this BOSCH appliance. You have acquired a high-quality product that will bring you a lot of enjoyment.
Please read the operating instructions carefully and keep them for future reference!
Safety instructions
This appliance is designed for domestic use or for use in non-commercial, householdlike environments, such as staff kitchens in shops, offices, agricultural and other small businesses or for use by guests at bed-and- breakfast establishments, small hotels and similar residential facilities.
! Risk of electric shock
Connect and operate the appliance only in accordance with the specifications on the rating label.
Do not use if either the power cord or the appliance is damaged.
Keep children away from the appliance. Children should be supervised to ensure that they do not play with the appliance. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Unplug after every use or if defective. Repairs to the appliance, such as replacing
a damaged power cord, may only be carried out by our customer service in order to avoid risks.
The power cord should not ––touch hot parts,
––be pulled over sharp edges, ––be used as a carrying handle.
Do not place the base or the kettle on or near hot surfaces such as a cooker or hob.
en
Never leave the kettle unattended while it is in use!
! Risk of scalding
The kettle gets hot during use. Therefore use only the handle to pick it up and open the lid 2 only after the kettle has cooled down.
Do not use near water contained in bathtubs, sinks, or in other containers.
Parts and operating controls
1 Kettle (with water level indicator)
2 Lid
3 Lid release button
4 ON/OFF O switch
5 Temperature indicator (illuminated)
6 + – button (temperature setting)
7 U button (keep warm)
8 Limescale filter (removable)
9 Base
10 Cable tidy
Important
Use the kettle 1 only with its included base 9.
●●Only fill the kettle with water. Milk and instant beverages will burn and damage the appliance. Never operate the kettle 1 without water and do not overfill it; observe the min and max markings. If the kettle is too full, the water will boil over!
Robert Bosch Hausgeräte GmbH
TWK861.indd 2 |
30.08.2011 16:45:19 |
en
Before using for the first time
●●Remove any stickers or film.
●●Unroll the right amount of cable from the cable tidy 10 and plug it in.
●●Fill the kettle 1 with water. Bring the water to a boil and discard it. Repeat the procedure. This will make sure that the kettle is clean for normal use.
●●When the water comes to a boil for the first time, add a tablespoon of white vinegar.
Boiling water
●●Fill the kettle with fresh water through the spout or the open lid 2 (press lid release button 3).
●●Check the amount by reading the water level indicator markings (min and max).
●●Close the lid 2 until it locks and place the kettle 1 on the base 9.
●●Press the O ON/OFF switch 4. The kettle emits a signal, and the factory-set temperature (100°C) lights up. The water is being heated.
●●By pressing button 6 + or – you can set the temperature to ca. 70°C, ca. 80°C, ca. 90°C or ca. 100°C.
●●When the water has reached the selected temperature, the kettle will switch off automatically, the temperature indicator 5 goes off, and a signal sounds.
Note: The selected temperature can be changed at any time while the kettle is heating up. While the kettle heats up, the current temperature lights up; the preset temperature flashes until it has been reached.
If the temperature cannot be set, this indicates that the water in the kettle is hotter than the desired temperature. The current temperature will light up.
3
You can turn off the kettle at any time by pressing the O ON/OFF switch 4 again.
Warning: If you remove the kettle 1 from the base and replace it before the heating process is over, the kettle will not continue to heat the water. The selected settings will be lost (reset to factory setting).
N.B.: Use the kettle only while the lid 2 is closed and the limescale filter 8 is in place. For physical reasons, the base 9 may collect some condensation water. This is normal; it does not mean that the kettle 1 leaks.
When you set the temperature to 100°C, the kettle will turn off only after the water has reached the boiling point, i.e. it will bubble for a short period of time.
After boiling, let the kettle cool down for 5 minutes before refilling it with water.
Do not turn on the appliance if the kettle 1 is empty, otherwise the overheat control will engage and the appliance will switch itself off automatically.
Keep warm setting
You can turn on the keep warm with any temperature setting.
Press button 7 U lights up, and the function is activated.
To turn it off, press button 7 again. The U indicator goes off.
Note: The keep warm feature switches off automatically after 30 minutes. The kettle emits a signal.
TWK8610... 09/2011
TWK861.indd 3 |
30.08.2011 16:45:19 |
Loading...