Bosch Universal Aquatak 125, Universal Aquatak 130, Universal Aquatak 135 User Manual

OBJ_DOKU-58312-003.fm Page 1 Tuesday, July 11, 2017 10:21 AM

			Robert Bosch Power Tools GmbH
			70538 Stuttgart
			GERMANY	UniversalAquatak
			www.bosch-do-it.com
			F 016 L81 569 (2017.08) O / 72	125 | 130 | 135

en Original instructions cn tw

ko

th id Petunjuk-Petunjuk untuk

Penggunaan Orisinal

vi Bản gốc hướng dẫn sử dụng

OBJ_BUCH-3065-002.book Page 2 Monday, May 8, 2017 3:20 PM

2 |

English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . Page 3
. . . . . . . . . . . . . . . . . . . .	. .	13
. . . . . . . . . . . . . . . . . . . .	. .	20
. . . . . . . . . . . . . . . . . . . . . . . .	27

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Bahasa Indonesia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Halaman 43

Tiếng Việt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trang 52

	F 016 L81 569 | (8.5.17)				Bosch Power Tools

OBJ_BUCH-3065-002.book Page 3 Monday, May 8, 2017 3:20 PM

English

Safety Notes Explanation of symbols

General hazard safety alert.

Never direct the water jet

at people, animals, the

unit or electric components.

Warning: High pressure jets can be dangerous if subject to misuse.

According to the applicable regulations, the appliance

must never be used on the drinking water network without a system separator. Use a separator as per IEC 61770 Type BA.

Water flowing though a system separator is considered not drinkable.

Safety Notes for pressure washer

Read all safety warnings and

all instructions. Failure to follow the warnings and instruc-

tions may result in electric shock, fire and/or serious injury.

The warning and information signs attached to the unit provide important information for safe operation.

Apart from the information in the operating instructions comply with the general safety regulations and regulations for the prevention of accidents.

English | 3

Connecting to the mains

The voltage indicated on the rating plate must correspond to the voltage of the power source.

We recommend that this equipment is only connected into a socket which is protected by a circuit-breaker that would be actuated by a 30 mA residual current.

Remove the plug from socket whenever the machine is left unattended for any period.

The electric supply installation should comply with IEC 60364-1.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

If the plug is damaged, pay attention to the following:

Plugs and sockets situated near the work site or outdoors should be to class IP 55 of BS 5490 to provide adequate protection against ingress of water, etc. and cable entries require effective sealing. Rubber shrouds should be provided over cable glands. Drip-proof (class IP X2 of

BS 5490) plugs and sockets to

BS 4343 are suitable for use indoors where the plug is away from the water spray area where the appliance is in use.

Never touch the mains plug with wet hands.

Do not pull plug while operating the device.

Do not run over, crush or pull the power supply cord or extension cord,

	Bosch Power Tools				F 016 L81 569 | (8.5.17)

OBJ_BUCH-3065-002.book Page 4 Monday, May 8, 2017 3:20 PM

4 | English

otherwise it may be damaged. Protect the cable from heat, oil and sharp edges.

Do not use the unit, if the power supply cord or important parts, e. g. high-pressure hose, power gun or safety devices are damaged.

Warning: Inadequate extension cords can be dangerous.

If an extension cord is used, the plug and socket must be of watertight construction. The extension cord must have a cross section in accordance with the operating instructions and be protected against splashed water. The connection must not be in water.

When replacing plugs on the power supply cable or extension lead the spray water guard and mechanical stability must remain intact.

Water connection

Comply with the regulations of your water supply company.

All connecting hoses must have properly sealed joints.

Make sure that the supply hose is at least 12.7 mm (1/2") in diameter and is reinforced.

The appliance should never be used on the drinking water supply without a back flow valve. Water which has passed the back flow valve is regarded as undrinkable.

The high-pressure hose must not be damaged (danger of bursting). A damaged high-pressure hose must be replaced immediately. Only use hoses and connections recommended by the manufacturer.

High-pressure hoses, fittings and couplings are important for the safety of the appliance. Use only hoses, fittings and couplings recommended by the manufacturer.

Only clean or filtered water should be used for intake.

Application

Before use, check that the unit and operating equipment are in perfect condition and are safe to operate. Do not use the unit if it is not in perfect condition.

Do not direct the jet against yourself or others in order to clean clothes or footwear.

Do not use solvent-containing liquids, undiluted acids, acetone or solvents! This includes petrol, paint thinners, heating oil. The sprayed vapour is highly flammable, explosive and toxic.

The appropriate safety regulations must be observed when using the unit in dangerous areas (e. g. petrol stations). It is forbidden to operate the unit in potentially explosive locations.

The unit must be placed on a solid base.

Take care if using the machine in a confined space ensuring that there is adequate ventilation. Ensure that all vehicles are switched off at all times whilst cleaning.

Operation of this machine requires both hands to be used at all times. Do not operate from a ladder. Take care when using the machine on balconies

	F 016 L81 569 | (8.5.17)				Bosch Power Tools

OBJ_BUCH-3065-002.book Page 5 Monday, May 8, 2017 3:20 PM

or other raised areas ensuring that you can see any edges at all times.

Only use detergents recommended by the manufacturer. Comply with the application, disposal and warning instructions of the detergent manufacturers.

All current-conducting components in the working area must be protected against splashed water.

The gun trigger must not be jammed in position “ON” during operation.

Wear suitable protective clothing to protect against splash water. Do not use the machine in reach of persons, unless these are also wearing protective clothing.

If necessary wear personal protective equipment (PPE) e. g. safety goggles, breathing protection etc to protect against water, particles and/or aerosols sprayed back from parts.

During use of high pressure cleaners, aerosols may be formed. Inhalation of aerosols can be hazardous to health.

High pressure may cause objects to rebound. If necessary wear suitable personnel protective equipment such as safety goggles.

Vehicle tyres/tyre valves may only be cleaned from a minimum distance of 30 cm in order to avoid damages by the high-pressure jet. The first indication of damage is the discolouration of the tyre. Damaged vehicle tyres/ tyre valves are dangerous to life.

Materials containing asbestos and other materials which contain sub-

English | 5

stances which are hazardous to your health must not be sprayed.

Detergents must not be used undiluted. The products are safe to use as they contain no acids, alkalis or substances which are detrimental to the environment. We recommend that the detergents are kept out of the reach of children. If detergent comes into contact with the eyes, wash immediately with plenty of water and if swallowed contact a doctor immediately.

Never use the power washer without water filter, or with a contaminated or damaged water filter. Using the power washer without water filter or with a contaminated or damaged water filter shall void the warranty.

Metal parts may become hot after prolonged usage, if necessary wear protective gloves.

Avoid high pressure washing in bad weather conditions especially when there is a risk of lightning.

Operation

The operator must use the unit in accordance with the regulations. He/she must take local conditions into account and be aware of other people, especially children, when operating the unit.

The unit may only be used by authorised persons who have received training or have demonstrated their ability to operate the unit. The unit must not be operated by children or

	Bosch Power Tools				F 016 L81 569 | (8.5.17)

OBJ_BUCH-3065-002.book Page 6 Monday, May 8, 2017 3:20 PM

6 | English

juveniles (danger of accidents due to incorrect use of the unit).

Never allow children, persons with physical, sensory or mental limitations or a lack of experience and/or knowledge and/or people unfamiliar with these instructions to use the machine. Local regulations may restrict the age of the operator.

Children should be supervised to ensure that they do not play with the machine.

The unit must never be left unsupervised while the unit is switched on.

The water jet from the high-pressure nozzle produces a recoil on the gun. You should therefore hold the gun and spray lance firmly with both hands.

Never use a roto nozzle or pencil jet to clean motor vehicles.

Transport

Switch off the motor and secure the unit before transporting.

Maintenance

Switch off the unit prior to all cleaning and maintenance work and before replacing components. Pull out the mains plug if the unit is mains-operat- ed.

Repairs may only be carried out by authorised Bosch Service Centres.

Accessories and spare parts

Accessories and spare parts which have been approved by Bosch must be used. Original accessories and spare parts guarantee that the unit can be operated safety and without any breakdowns.

Symbols

The following symbols are important for reading and understanding the operating instructions. Please take note of the symbols and their meaning. The correct interpretation of the symbols will help you to use the machine in a better and safer manner.

Symbol	Meaning
	Movement direction
	Reaction direction
	Weight
	On
	Off
	Accessories

Intended Use

The product is intended for cleaning areas and objects outside the house, tools, vehicles and boats, if the appropriate accessories and cleaning agents approved by Bosch are used.

Intended use is related to operation within 0 ° C and 40 ° C ambient temperature.

This product should not be used for professional use.

	F 016 L81 569 | (8.5.17)				Bosch Power Tools

OBJ_BUCH-3065-002.book Page 7 Monday, May 8, 2017 3:20 PM

				English | 7
Technical Data
Pressure washer		Universal	Universal	Universal
		Aquatak 125	Aquatak 130	Aquatak 135
Article number		3 600 HA7 A..	3 600 HA7 B..	3 600 HA7 C..
Rated power	kW	1.5	1.7	1.9
Supply temperature max.	° C	40	40	40
Supply rate min.	l/min	6	7	7.5
Allowable pressure	MPa	7.5	9	9.2
Rated pressure	MPa	12.5	13	13.5
Rated Flow	l/min	5.3	6	6.4
Maximum inlet pressure	MPa	1	1	1
Autostop function		●	●	●
Weight according to EPTA-Procedure 01:2014	kg	6.8	7.8	7.9
Protection class		/ II	/ II	/ II
Serial number		See serial number (rating plate) on pressure washer.

The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.

Starting cycles generate brief voltage drops. Interference with other equipment/machines may occur in case of unfavourable mains system conditions. Malfunctions are not to be expected for system impedances below 0.153 ohm. If in doubt please contact your Supply Authority.

Mounting and Operation

Action	Figure	Page
Delivery Scope	1	61
Fold down handle operation	2	62
Adjusting the Handle	3	62
Connecting to the water supply	4	63
Connecting/Disconnecting high
pressure gun to lance	5	63
Connecting high pressure water supply
hose/nozzle	6	64
Disconnecting high pressure water
supply hose/nozzle	7	64
Switching On and Off	8	65
Attaching Nozzles
Adjust water jet	9 – 10	66 – 67
Connect detergent bottle	11	68
Clean nozzle	12	69
Clean the water filter	13	69
Hose into the hose holder	14	70
Storage	15	70
Gun/lance/nozzle is stored in action	16	70
Selecting Accessories	17	71

Starting

Electrical Safety

Warning! Switch off, remove plug from mains before adjusting, cleaning or if cable is cut, damaged or entangled.

Your machine is double insulated for safety and requires no earth connection. The operating voltage is 230 V AC, 50 Hz (for non-EU countries 220 V, 240 V as applicable).

For increased electrical safety use a Residual Current Device (RCD) with a tripping current of not more than 30 mA. Always check your RCD every time you use it.

The supply cables must be inspected for signs of damage at regular intervals and may only be used if in perfect condition.

If the replacement of the supply cord is necessary, this has to be done by Bosch or an authorized Bosch service agent in order to avoid a safety hazard.

Only use approved extension cables.

WARNING! Inadequate extension cables can be dangerous. Extension cable, plug and socket must be of watertight construction and intended for outdoor use.

Extension cords, cables, leads, reels should only be used if they comply with EN 61242/IEC 61242 or

IEC 60884-2-7.

If you want to use an extension cable when operating your product, only the following cable dimensions should be used:

–Nominal Conductor Area of 1.5mm2 to a max. cable length of 20m for a Cord Extension Set

The connections (plugs and sockets) should be kept dry and off the ground.

It is recommended that this is accomplished by means of a cord reel which keeps the socket at least 60 mm above the ground.

Note: If an extension cable is used it must be earthed and connected through the plug to the earth cable of your supply network in accordance with prescribed safety regulations.

Refer to the instruction manual of the extension cord, lead, reel manufacturer and your local wiring regulations.

	Bosch Power Tools				F 016 L81 569 | (8.5.17)

OBJ_BUCH-3065-002.book Page 8 Monday, May 8, 2017 3:20 PM

8 | English

If in doubt contact a qualified electrician or the nearest Bosch Service Centre.

For products not sold in GB:

WARNING: For your safety, it is required that the plug attached to the product is connected with the extension cord. The coupling of the extension cord must be protected against splash water, be made of rubber or coated with rubber. The extension cord must be used with a cable strain relief.

Products sold in GB only: Your product is fitted with a BS 1363/A approved electric plug with internal fuse (ASTA approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place by an authorised customer service agent. The replacement plug should have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible shock hazard and should never be inserted into a mains socket elsewhere.

Products sold in AUS and NZ only: Use a residual current device (RCD) with a rated residual current of 30 mA or less.

Operation

Starting

Attach water supply hose (not supplied) to the mains water supply and machine.

Connect the product to the mains supply ensuring that the mains switch is in the off position.

Open water tap.

Press the safety lock (back button on the gun handle) to release the trigger. Fully press the trigger until there is a constant flow of water to clear the air from the machine and water supply hose. Release trigger. Press the safety lock (front button on the gun handle).

Turn button on main switch. Point the power gun downwards. Press the trigger safety lock to release the trigger. Fully press the trigger.

Autostop function

The machine is designed to switch off the motor when the trigger is released on the gun.

Working Advice

General

Ensure that the pressure washer is on level ground.

Do not overreach with the high pressure hose or move the pressure washer by pulling the hose, this could cause the machine to become unstable and fall over.

Do not kink or drive a motor vehicle over the high pressure hose. Do not expose the high pressure hose to sharp edges or corners.

Never use a roto nozzle or pencil jet to clean motor vehicles.

Working advice for cleaning with detergents

Only use cleaning agents suitable specifically for high pressure washers.

We recommend that you use detergent sparingly for the sake of the environment. Observe the recommended dilution on the detergent label.

The high-pressure foam nozzle supplied with this product includes a regulator to control detergent use. Adjust as required.

Recommended cleaning method

Step 1: Select the fan jet setting on the 3 in 1 nozzle and remove the heavy dirt.

Step 2: Attach the foam bottle and spray on the detergent sparingly.

Step 3: Rinse off the loosened dirt and detergent using the fan jet setting on the 3 in 1 nozzle.

Note: When cleaning vertical surfaces, apply the detergent from bottom to top. When rinsing off, work from top to bottom.

Use with alternative water sources

The power washer is self-priming and enables water to be drawn in from containers or natural water sources. It is IMPORTANT that the water filter is in clean condition when inserting it at the water inlet, and that only clean water is drawn in.

Open tanks/containers and natural water sources

Use the Self Priming accessory kit comprising:

–Inlet strainer with non return valve

–3 m reinforced supply hose

–Universal coupling to the pressure washer

This enables the pressure washer to draw water up to 0.5 m above the water level in the source in approximately 15 seconds.

Fully immerse the 3 m hose into the water to displace the air in the hose. Connect the 3 m hose to the power washer and make sure that the inlet strainer remains under water.

With the spray gun removed, switch the power washer on and operate it until water flows uniformly out of the high-pressure hose. If no water is coming out of the high-pressure hose after 25 seconds, switch the power washer off and check all connections. As soon as water flows out of the high-pressure hose, switch the power washer off and connect the spray gunand spray lance to begin with the work.

It is important that hose and couplings are of good quality and are tightly connected, and that the seals are undamaged and properly inserted. Loose connections can impede the priming (drawing in).

Water Tanks with outlet connections

When connecting the pressure washer to a water tank with a suitable tap outlet, first connect the supply hose (not provided) to the tank outlet, open the tap to allow the water to displace all the air in the hose and then connect to the pressure washer.

	F 016 L81 569 | (8.5.17)				Bosch Power Tools

OBJ_BUCH-3065-002.book Page 9 Monday, May 8, 2017 3:20 PM

English | 9

Troubleshooting

Problem	Possible Cause	Corrective Action
Motor refuses to start	Plug not connected	Connect plug
	Mains socket faulty	Use another socket
	Fuse faulty / blown	Replace fuse
	Extension cable damaged	Try without extension cable
	Motor protector has activated	Allow to cool for 15 minutes
	Frozen	Wait for pump/water supply hose/accessory to
		thaw
Motor stops	Fuse faulty / blown	Replace fuse
	Wrong mains voltage	Check that mains voltage corresponds to
		specifications on the model tag
	Motor protector has activated	Allow to cool for 15 minutes
	Wrong mains voltage	Check that mains voltage corresponds to
		specifications on the model tag
Fuses blow	Fuses incorrectly rated	Change to a mains supply higher than the pressure
		washer amp consumption
Motor starts but no pressure	Nozzle partly blocked	Clean nozzle
Motor “sounds” but fails to start	Insufficient power supply	Check that the voltage of the mains power supply
		line is the same as that on the plate
	Voltage loss due to use of extension	Check characteristics of extension cable
	cable
	Appliance not used for a long period	Contact your Bosch Service Centre
	of time
	Problems with TSS (Total Stop	Contact your Bosch Service Centre
	System) device
	Problems with TSS (Total Stop	Contact your Bosch Service Centre
	System) device

Pressure pulsating	Air in the inlet water supply
	hose/pump

Allow pressure washer to run with open spray handle and nozzle at low pressure until regular working pressure is obtained

				Inadequate water supply			Check that the water supply corresponds to
							specifications. The minimum specification for the
							water supply hose is 1/2" or 13 mm diameter
				Water filter blocked			Clean water filter
				Water supply hoses squeezed			Straighten out kinked water supply hoses
				High pressure hose too long			Remove high pressure extension hose. Retry
							(extension hose max. 7 m)
		Pressure too low, but steady		Nozzle worn			Change the nozzle
		Note: Several types of accessory		Start/stop valve worn			Activate trigger five times in quick succession
		will normally deliver a lower
		pressure
		Motor starts up but with restricted		No water supply			Connect water supply
		or no working pressure
				Water filter clogged up			Clean the water filter
				Nozzle clogged up			Clean nozzle
		The pressure washer starts		Pump/ spray gun leaky			Contact your Bosch Service Centre
		irregularly by itself
		Water leaks from machine		Leaking pump			A slight water leak is permissible; in case of
							excessive leak, contact Bosch Service Centre
		Bosch Power Tools					F 016 L81 569 | (8.5.17)

OBJ_BUCH-3065-002.book Page 10 Monday, May 8, 2017 3:20 PM

10 | English

Problem	Possible Cause	Corrective Action
No detergent taken in	Detergent too dense	Dilute with water

Residue or restriction in cleaningagent nozzle

Flush with clean water and eliminate any restrictions. If the problem persists, contact your Bosch Service Centre.

Maintenance and Service

Maintenance

Stop, remove plug from the power supply and disconnect from water supply.

Note: To ensure long and reliable service, carry out the following maintenance regularly.

Regularly check for obvious defects such as loose fixings, and worn or damaged components.

Check that covers and guards are undamaged and correctly fitted. Carry out necessary maintenance or repairs before using.

If the replacement of the supply cord is necessary, this has to be done by Bosch or an authorized Bosch service agent in order to avoid a safety hazard.

After use/Storage

Turn the main switch off and operate the trigger to drain the water from the high pressure hose.

Clean the exterior of the machine thoroughly using a soft brush or cloth. Do not use water, solvents or polishes. Remove all debris, especially from the ventilation slots.

End of season storage: Drain water out of pump running motor for a few seconds. Pull trigger to release all water.

Do not place other objects on top of the machine. Store in a frost-free area.

Ensure cables are not trapped when storing. Do not kink high pressure hose.

After-sales Service and Application Service www.bosch-do-it.com

In all correspondence and spare parts orders, please always include the 10-digit article number given on the type plate of the machine.

Cambodia

Robert Bosch (Cambodia) Co., Ltd

Unit 8BC, GT Tower, 08th Floor, Street 169,

Czechoslovakia Blvd, Sangkat Veal Vong

Khan 7 Makara, Phnom Penh

VAT TIN: 100 169 511

Tel.: [phone]

Tel.: [phone]

www.bosch.com.kh

People’s Republic of China China Mainland

Bosch Power Tools (China) Co., Ltd. 567, Bin Kang Road

Bin Jiang District 310052 Hangzhou, P. R. China Tel.: [phone]

Fax: [phone]

E-Mail: [e-mail] www.bosch-pt.com.cn

HK and Macau Special Administrative Regions

Robert Bosch Co. Ltd.

21st Floor, 625 King’s Road North Point, Hong Kong

Customer Service Hotline: [phone] Fax: [phone]

E-Mail: [e-mail] www.bosch-pt.com.hk

India

Bosch Service Center

69, Habibullah Road, (Next to PSBB School), T. Nagar Chennai – 600077

Phone: [phone]

Bosch Service Center Rishyamook

85A, Panchkuin Road

New Delhi – 110001

Phone: [phone]

Bosch Service Center

79, Crystal Bldg., Dr. Annie Besant Road, Worli Mumbai – 400018

Phone: [phone]

Indonesia

PT Robert Bosch

Palma Tower 10th Floor

Jalan RA Kartini II-S Kaveling 6

Pondok Pinang, Kebayoran Lama

Jakarta Selatan 12310

Tel.: [phone]

www.bosch-pt.co.id

	F 016 L81 569 | (8.5.17)				Bosch Power Tools

OBJ_BUCH-3065-002.book Page 11 Monday, May 8, 2017 3:20 PM

Malaysia

Robert Bosch Sdn. Bhd.(220975-V) PT/SMY No. 8A, Jalan 13/6

46200 Petaling Jaya Selangor

Tel.: [phone] Toll-Free: 1800 880188 Fax: [phone]

E-Mail: [e-mail] www.bosch-pt.com.my

Pakistan

Robert Bosch Middle East FZE – Pakistan Liaison Office 2nd Floor Plaza # 10, CCA Block, DHA Phase 5

Lahore, 54810

Phone: [phone] Email: [e-mail]

Philippines

Robert Bosch, Inc.

28th Floor Fort Legend Towers, 3rd Avenue corner 31st Street, Fort Bonifacio, Global City, 1634 Taguig City

Tel.: [phone]

Fax: [phone] www.bosch-pt.com.ph

Singapore

Powerwell Service Centre Ptd Ltd

Bosch Authorised Service Centre (Power Tools) 4012 Ang Mo Kio Ave 10, #01-02 TECHplace Singapore 569628

Tel.: [phone]

Fax: [phone]

E-Mail: [e-mail] www.powerwellsc.com www.bosch-pt.com.sg

Thailand

Robert Bosch Ltd.

Liberty Square Building

No. 287, 11 Floor

Silom Road, Bangrak

Bangkok 10500

Tel.: [phone]

Fax: [phone]

Robert Bosch Ltd., P. O. Box 2054

Bangkok 10501

www.bosch.co.th

Bosch Service – Training Centre

La Salle Tower Ground Floor Unit No.2

10/11 La Salle Moo 16

Srinakharin Road

Bangkaew, Bang Plee

Samutprakarn 10540

Tel.: [phone]

Fax: [phone]

English | 11

Vietnam

Branch of Bosch Vietnam Co., Ltd in HCMC Floor 10, 194 Golden Building

473 Dien Bien Phu Street

Ward 25, Binh Thanh District, Ho Chi Minh City Tel.: [phone]

Fax: [phone] Hotline: [phone] www.bosch-pt.com.vn

Armenia, Azerbaijan, Georgia, Kyrgyzstan, Mongolia, Tajikistan, Turkmenistan, Uzbekistan

TOO “Robert Bosch” Power Tools, After Sales Service Rayimbek Ave., 169/1

050050, Almaty, Kazakhstan

Service Email: [e-mail]

Official Website: www.bosch.com, www.bosch-pt.com

Bahrain

Hatem Al Juffali Technical Equipment Establishment. Kingdom of Bahrain, Setra Highway, Al Aker Area Phone: [phone]

Fax: [phone]

Email: [e-mail]

Egypt

Unimar

20 Markaz kadmat

El tagmoa EL Aoul – New Cairo Phone: + 20 2224 76091-95 Phone: + 20 2224 78072-73 Fax: + 20 2224 78075

Email: [e-mail]

Iran

Robert Bosch Iran

3rd Floor, No 3, Maadiran Building Aftab St., Khodami St., Vanak Sq. Tehran 1994834571

Phone: [phone]

Iraq

Sahba Technology Group

Al Muthana airport road

Baghdad

Phone: [phone]

Phone Dubai: [phone]

Email: [e-mail]

Jordan

Roots Arabia – Jordan

Nasser Bin Jameel street, Building 37 Al Rabiah 11194 Amman

Phone: [phone] Email: [e-mail]

	Bosch Power Tools				F 016 L81 569 | (8.5.17)

OBJ_BUCH-3065-002.book Page 12 Monday, May 8, 2017 3:20 PM

12 | English

Kuwait

Al Qurain Automotive Trading Company

Shuwaikh Industrial Area, Block 1, Plot 16, Street 3rd P.O. Box 164 – Safat 13002

Phone: [phone] Fax: [phone]

E-mail: [e-mail]

Lebanon

Tehini Hana & Co. S.A.R.L.

P.O. Box 90-449

Jdeideh

Dora-Beirut

Phone: [phone]

Email: [e-mail]

Libya

El Naser for Workshop Tools

Swanee Road, Alfalah Area

Tripoli

Phone: [phone]

Oman

Malatan Trading & Contracting LLC

P.O. Box 131

Ruwi, 112 Sultanate of Oman

Phone: [phone]

Email: [e-mail]

Qatar

International Construction Solutions W L L P. O. Box 51, Doha

Phone: [phone] Fax: [phone] Email: [e-mail]

Saudi Arabia

Juffali Technical Equipment Co. (JTECO) Kilo 14, Madinah Road, Al Bawadi District Jeddah 21431

Phone: [phone] Ext. 1528 Fax: [phone]

Email: [e-mail]

Syria

Dallal Establishment for Power Tools

P.O. Box 1030

Aleppo

Phone: [phone]

Email: [e-mail]

United Arab Emirates

Central Motors & Equipment LLC, P.O. Box 1984 Al-Wahda Street – Old Sana Building

Sharjah

Phone: [phone] Fax: [phone]

Email: [e-mail]

Yemen

Abualrejal Trading Corporation

Sana’a Zubiery St. Front to new Parliament Building Phone: [phone]

Fax: [phone]

Email: [e-mail]

Ethiopia

Forever plc

Kebele 2,754, BP 4806,

Addis Ababa

Phone: [phone]

Email: [e-mail]

Ghana

C.WOERMANN LTD.

Nsawam Road/Avenor Junction, P.O. Box 1779

Accra

Phone: [phone]

Kenya

Robert Bosch East Africa Ltd

Mpaka Road P.O. Box 856

00606 Nairobi

Nigeria

Robert Bosch Nigeria Ltd.

52 – 54 Isaac John Street P.O. Box

GRA Ikeja – Lagos

Republic of South Africa

Customer service

Hotline: [phone]

Gauteng – BSC Service Centre

35 Roper Street, New Centre Johannesburg

Tel.: [phone]

Fax: [phone] E-Mail: [e-mail]

KZN – BSC Service Centre

Unit E, Almar Centre

143 Crompton Street Pinetown

Tel.: [phone]

Fax: [phone]

E-Mail: [e-mail]

Western Cape – BSC Service Centre

Democracy Way, Prosperity Park

Milnerton

Tel.: [phone]

Fax: [phone]

E-Mail: [e-mail]

Bosch Headquarters

Midrand, Gauteng

Tel.: [phone]

Fax: [phone]

E-Mail: [e-mail]

	F 016 L81 569 | (8.5.17)				Bosch Power Tools

OBJ_BUCH-3065-002.book Page 13 Monday, May 8, 2017 3:20 PM

Tanzania

Diesel & Autoelectric Service Ltd.

117 Nyerere Rd., P.O. Box 70839

Vingunguti 12109, Dar Es Salaam

Phone: [phone]

Australia, New Zealand and Pacific Islands

Robert Bosch Australia Pty. Ltd.

Power Tools

Locked Bag 66

Clayton South VIC 3169

Customer Contact Center

Inside Australia:

Phone: [phone]

Fax: [phone]

Inside New Zealand:

Phone: [phone]

Fax: [phone]

Outside AU and NZ:

Phone: [phone]

www.bosch-pt.com.au

www.bosch-pt.co.nz

Environmental Protection

Chemicals dangerous to the environment must not be allowed to enter the ground, ground water or ponds, streams, etc.

For the use of cleaning agents, observe the instructions on the package and the prescribed concentration exactly.

For the cleaning of motor vehicles the local regulations should be observed: Do not allow oil sprayed off to enter into the ground water. Recycle raw materials instead of waste disposal.

Disposal

The pressure washer, accessories and packaging should be sorted for environmental-friendly recycling.

Do not dispose of pressure washers into household waste!

Only for EC countries:

According to the European directive 2012/19/EU for Waste Electrical and Electronic Equipment and its implementation into national law, electrical and electronic equipment that are no longer usable must be collected separately and disposed of in an environmentally correct manner.

Subject to change without notice.

| 13

电动零件。

能造成危险。

IEC 61770

BA

/

和意外防范规定。



 30 mA

	Bosch Power Tools				F 016 L81 569 | (8.5.17)

OBJ_BUCH-3065-002.book Page 14 Monday, May 8, 2017 3:20 PM

14 |





IEC 60364-1



 











 

 12,7

1/2"





















	F 016 L81 569 | (8.5.17)				Bosch Power Tools

OBJ_BUCH-3065-002.book Page 15 Monday, May 8, 2017 3:20 PM







 "ON"



 PSA /





 30 /

| 15















 //

	Bosch Power Tools				F 016 L81 569 | (8.5.17)

OBJ_BUCH-3065-002.book Page 16 Monday, May 8, 2017 3:20 PM

16 |

















0 40

		Universal	Universal	Universal
		Aquatak 125	Aquatak 130	Aquatak 135
		3 600 HA7 A..	3 600 HA7 B..	3 600 HA7 C..
	kW	1,5	1,7	1,9
	°C	40	40	40
	/	6	7	7,5
	MPa	7,5	9	9,2
	MPa	12,5	13	13,5
	/	5,3	6	6,4
	MPa	1	1	1

230 V

0,153

F 016 L81 569 | (8.5.17) Bosch Power Tools

OBJ_BUCH-3065-002.book Page 17 Monday, May 8, 2017 3:20 PM

				| 17
		Universal	Universal	Universal
		Aquatak 125	Aquatak 130	Aquatak 135
		●	●	●
EPTA-Procedure 01:2014		6,8	7,8	7,9
		/II	/II	/II
		( )

230 V

0,153

	1	61
	2	62
	3	62
	4	63
/
	5	63
/	6	64
/	7	64
/	8	65
	9–10	66–67
	11	68
	12	69
	13	69
	14	70
	15	70
/ /	16	70
	17	71

以上措施。

工作电压为230 AC 50

220 240

30 mA(RCD)

安全性能。

长线、插头和联结装置。

EN61242/ IEC61242 IEC60884-2-7

面

– 1,5 2 20

面至少要有60

是由橡胶制成或者覆盖着橡胶套。延长线上必须有防拉 扯装备。

上。

"0"

的锁定。将扳机按到底直到水流均匀并且机器和高压软

	Bosch Power Tools				F 016 L81 569 | (8.5.17)

OBJ_BUCH-3065-002.book Page 18 Monday, May 8, 2017 3:20 PM

18 |

达。

保护高压软管免被锋利的边缘或尖锐的凸角割损。





容器上所标示的有关稀释清洁剂的建议说明。

关。您可以根据需要调整清洁剂的排量。

1 :

2

3 :

接着再从上端朝下冲洗。

器清洁。只能吸汲干净的水。

/

–3

, 0,5 15

3 3

清洁机流出的水稳定且均匀为止。如果过了25 ,,

的插入联结器中。如果连接不紧密会影响吸力。

洁机上。

							15
							15
		F 016 L81 569 | (8.5.17)					Bosch Power Tools

OBJ_BUCH-3065-002.book Page 19 Monday, May 8, 2017 3:20 PM

		| 19
	TSS- (Total Stop System
	)
		1/2 13
		- 7
:	/	5

命和确保操作安全。

和磨损的机件等。

时得在使用机器前执行维护或修理的工作。

/

马达的通气缝隙。

行数秒并扣动扳机。

安全性能。

	Bosch Power Tools				F 016 L81 569 | (8.5.17)

OBJ_BUCH-3065-002.book Page 20 Monday, May 8, 2017 3:20 PM

20 |

www.bosch-do-it.com

10

询。

滨江区滨康路567

3100524008268484(0571) [e-mail] www.bosch-pt.com.cn

· 625 21

[phone]+852 2590 [e-mail]

Robert Bosch Power Tools GmbH

·

70538 Stuttgart / GERMANY

70538 /

规定的使用浓度。

来的油垢流入地下水中。

2012/19/EU

電動零件。

能造成危險。

IEC 61770

BA

/

和意外防範規定。



 30 mA

	F 016 L81 569 | (8.5.17)				Bosch Power Tools

OBJ_BUCH-3065-002.book Page 21 Monday, May 8, 2017 3:20 PM





IEC 60364-1



 











 

 12,7

1/2"

| 21





















	Bosch Power Tools				F 016 L81 569 | (8.5.17)

OBJ_BUCH-3065-002.book Page 22 Monday, May 8, 2017 3:20 PM

22 |







 "ON"



 PSA /





 30 /















 //

	F 016 L81 569 | (8.5.17)				Bosch Power Tools