Bosch D6600 User Manual 3

Conettix Communications Receiver/Gateway

D6600/D6100IPv6

en Installation and Operation Guide

	Conettix Communications Receiver/	Table of Contents | en	3
	Gateway

Table of contents

1	Emergency Procedures	6
2	Introduction	7
2.1	About documentation	7
2.2	Bosch Security Systems, Inc. Product Manufacturing Dates	7
3
	System overview	9
3.1	Parts List	10
4
	Quick Installation	11
4.1	Setting the Time and Date	13
5
	Card Functions and Locations	14
5.1	D6600 Front Panel	14
5.2	Line Cards and Modules	15
5.3	D6600 Rear View	16
5.3.1	D6600 Internal View	17
5.4	D6100IPv6 Front Panel	18
5.5	D6100IPv6 Rear View	18
6
	D6600 Specific Cards	19
6.1	D6640/D6641 Line Cards and D6645 Line Terminator Cards	19
6.1.1	D6640/D6641 LED Descriptions	20
6.2	Card Installation	20
6.3	D6610 CPU Card and D6615 CPU Terminator Card	22
6.4	Card Removal and Replacement	23
7
	Printer Specifications	24
8	Installation	25
8.1	Installation Check List	25
8.2	Rack Mount Instructions	26
8.3	Removing Power to the Receiver	26
9
	Power	27
9.1	Power Supply Modules	27
9.2	Main Power	27
9.3	Standby Power	27
9.4	Connecting External Batteries	27
9.4.1	Minimum Standby Battery	28
9.4.2	Minimum Standby UPS Power	29
9.4.3	Estimated BTU Load	29
10
	Input and Output Ports	30
10.1	Overview of Input and Output Ports	30
10.1.1	UPS Monitoring through CPU Programmable Input Ports	30
10.1.2	Automation Link Monitoring (COM3) through CPU Programmable Output Ports	32
11
	D6600/D6100IPv6 Operation	33
11.1	Process Flow	33
11.1.1	Receiver Handshake and Kiss-Off	33
11.1.2	Message Verification	33
11.1.3	Handshake Tone Compatibility	33
11.1.4	Message is Received	33
11.1.5	How Call Groups Work	34
11.1.6	Buzzer Operation	34
11.1.7	Reporting Devices: Primary and Secondary	34

Bosch Security Systems, Inc.

Installation and Operation Guide

2012.11 | 08 | 4998122704

4	en | Table of Contents		Conettix Communications Receiver/
				Gateway
11.2		Normal Operation Mode		35
11.3		Operating in Manual Mode		35
11.4		Keypad Menu Operation		36
11.4.1		Log In		36
11.4.2		Using the Keypad		36
11.4.3		Event Buffer Display		36
11.4.4		Current System Trouble Display		36
11.4.5		Software Version Display		37
11.4.6		Keypad Functions		37
11.5		Busy Seconds (Line Busy) Reports		38
11.6		Two-Way Audio		39
11.6.1		Enhancements and Changes		40
11.6.2		Two-Way Auto Modes of Operation		40
12
		Network Communications		42
12.1		Conettix D6600/D6100IPv6 Pre-installation Requirements		46
12.1.1		Setting Up the Conettix D6600/D6100IPv6 over an Ethernet Network		46
12.1.2		Host Computer for Conettix D6600/D6100IPv6 System Setup		46
12.2		Operation		46
12.2.1		Setting Up the Host Computer		46
12.2.2		Network Failover Solution (D6600 Only)		51
12.2.3		Conettix Datagram Type Differences		53
12.2.4		Networking and Encryption		54
12.3		Special Conettix D6600 Applications		56
12.4		D6100IPv6 Configuration Setup Instructions		57
12.4.1		Factory Default IP Address		57
12.4.2		Identifying the MAC Hardware Address		58
12.4.3		Obtaining an IP Address		58
12.4.4		Using the D6200 to configure the D6100IPv6		58
12.4.5		Configuring for Network Communication		63
12.5		D6100i Configuration Setup Instructions		64
12.5.1		Identifying the MAC Hardware Address		64
12.5.2		Obtaining an IP Address		64
12.5.3		Initial IP Address Assignment Using ARP.EXE		65
12.5.4		Using Telnet to Finish the Configuration		66
12.5.5		Configuration Using Telnet		67
12.5.6		Configuring for Network Communication		70
13
		No Data Received Reports		72
13.1		No Data Received		72
13.2		Data Error		72
13.3		Wrong Data		72
14
		Central Station Automation System		73
15		Central Station Tips		75
15.1		Back-up Receiver		75
15.2		Computer Interface		75
15.3		D6200 Programming Software		75
15.4		Telephone Lines		75
15.5		Proper Ground		75
15.6		Radio Frequency Interference		76
15.7		Test Communicator		76

2012.11 | 08 | 4998122704

Installation and Operation Guide

Bosch Security Systems, Inc.

Conettix Communications Receiver/		Table of Contents | en	5
Gateway
16
	Troubleshooting Guide		77
17
	Specifications		80
18
	Service Information		84

Bosch Security Systems, Inc.

Installation and Operation Guide

2012.11 | 08 | 4998122704

	6	en | Emergency Procedures	Conettix Communications Receiver/
			Gateway

1 Emergency Procedures

Notice!

Throughout this document references to D6100IPv6 also apply to the D6100IPv6 unless otherwise noted.

The Service Information, page 84 section of this guide contains a Service Information form. Keep this form current and accessible to central station personnel at all times in case of emergency.

If your D6600/D6100IPv6 becomes inoperable or experiences trouble receiving signals:

1.Notify your supervisor.

2.Refer to Troubleshooting Guide, page 77.

3.Contact Bosch Security Systems, Inc. at [phone] for assistance if you have a receiver spares package and need to replace a circuit card or module.

Notice!

The AC/DC Power Supply Module and DC/DC Power Supply Module for the D6600 are not field serviceable. Contact Bosch Security Systems, Inc. for service.

Caution!

Disconnect power to the receiver before removing the CPU or CPU terminator card.

Before Calling

1.Have this guide nearby and opened to Troubleshooting Guide, page 77.

2.Have your spares package, the D6200 Programming Software, and the D6600/D6100IPv6 Program Entry Guide (P/N: 4998122702) nearby.

3.Know the location of the telephone line jacks for the receiver.

4.Know the telephone numbers to the receiver’s telephone line cards.

5.Know the exact nature of the problem you are experiencing such as reports received, LEDs lit, or Operator Alert Buzzer sounded.

6.Have the service information form nearby (refer to Service Information, page 84).

2012.11 | 08 | 4998122704

Installation and Operation Guide

Bosch Security Systems, Inc.

	Conettix Communications Receiver/	Introduction | en	7
	Gateway

2	Introduction
2.1	About documentation
	Document Terminology
	Action buttons for the D6600/D6100IPv6 are described using the following terminology:
	D6600		D6100IPv6	Terminology
	[M/E]		[ENTER]	Enter
	[∆]		[∆]	Up (a level)
	[ ]		[ ]	Down (a level)
	[CAN]		[CANCEL]	Cancel
	[ ]		[ACKNOWLEDGE]	Acknowledge
	[F]		[FUNCTION]	Function
	Copyright
	This document is the intellectual property of Bosch Security Systems, Inc. and is protected by
	copyright. All rights reserved.
	Trademarks
	All hardware and software product names used in this document are likely to be registered
	trademarks and must be treated accordingly.
	Conettix Documentation
	Conettix DX4020 Installation Guide – F01U045288
	Conettix D6600/D6100IPv6 Quick Start (this document) – 4998122701
	Conettix D6600/D6100IPv6 Program Entry Guide – 4998122702
	Conettix D6600/D6100IPv6 Computer Interface Manual – 4998122703
	Conettix D6600/D6100IPv6 Release Notes – 4998122709
	D6202 Operation and Installation Guide – 4998122713
	Conettix D6201 Installation Instructions – 4998122717
	C900TTL-E Installation Guide – 4998122718
	DeviceInstaller Operation and Installation Guide – 4998138688
	Conettix D6680 Installation Guide – 4998138732
	Conettix ITS-D6686 Installation Guide – F01U078049
	Conettix D6600 Card Insertion Installation Guide – 4998141059
	Conettix D6200 Operation and Installation Guide – 4998154991
	Conettix C900V2 Installation Guide – F01U003472
	Ethernet Communication Module B420 Operation and Installation Guide – F01U215236
	Ethernet Communication Module B426 Operation and Installation Guide – F01U266226
2.2	Bosch Security Systems, Inc. Product Manufacturing Dates

Use the serial number located on the product label and refer to the Bosch Security Systems, Inc. web site at http://www.boschsecurity.com/datecodes.

The following image shows an example of a product label and highlights where to find the manufacturing date within the serial number.

Bosch Security Systems, Inc.

Installation and Operation Guide

2012.11 | 08 | 4998122704

8

en | Introduction

Conettix Communications Receiver/

Gateway

2012.11 | 08 | 4998122704

Installation and Operation Guide

Bosch Security Systems, Inc.

	Conettix Communications Receiver/	System overview | en	9
	Gateway

3 System overview

Notice!

The D6600/D6100IPv6 Installation and Operation Guide covers the general installation and operation of the products.

Refer to the appropriate Installation Supplement included with your product for the specifics of your particular installation.

Customers ordering a D6100IPv6-01 receive a Model D6100IPv6 Communications Receiver/ Gateway, and should refer to the UL864 & UL1610 Installation Supplement (P/N: F01U134241) included with the product.

The Conettix D6600/D6100IPv6 Communications Receiver/Gateway offers several unique features:

–Modular construction with plug-in circuit boards for quick, easy service

–Open-structure PC platform for future development

–Programmable formatting for receiving data from most major brands of digital communicators

–Easy and inexpensive updating using modular cards (D6600 only)

–Convenient software downloads

–Superior digital signal processing to reduce noise and signal loss

–User interface module with LED indicators

–Front panel keypad

–Alphanumeric liquid crystal display (LCD The D6600 metal enclosure contains several modular cards:

–Conettix D6610 Central Processing Unit (CPU) Card

–Conettix D6615 CPU Terminator Card

–Conettix D6640 or D6641 Telephone Line Card that supports four telephone line interfaces

–Conettix D6645 Telephone Line Terminator Card

Up to seven additional telephone line cards along with seven additional line terminator cards can be installed in the D6600 to expand the receiver’s capacity to 32 receiving lines.

D6600/D6100IPv6 Supported Communication Formats

Acron Super Fast	ROBOFON*
Ademco Slow	Scantronics Scancom*
Ademco Express	Seriee FSK/DTMF*
Ademco High Speed	Sescoa Super Speed
Ademco Contact ID	SIA 8/20/300
CFSK Bell/V.21*	SIA ADT*
FBI Superfast	SIA V.21*
Franklin/Sescoa	Silent Knight Fast
ITI*	Silent Knight FSK
Radionics BFSK	Standard Pulse Formats
Radionics Hex	Sur-Gard DTMF

Bosch Security Systems, Inc.

Installation and Operation Guide

2012.11 | 08 | 4998122704

	10 en | System overview	Conettix Communications Receiver/
		Gateway

Radionics Modem II	Telim*
Bosch Modem4/ModemIIIa²/ModemIIe	Veritech FSK
RB2000 (D6641 only)*	VONK (D6641 only)*
* Not investigated by UL.

– Use a printer to permanently record date, time, group number or transmission format and line number, account number, receiver number, and event by area, zone, and point. The printer tape and the D6600/D6100IPv6 LCD display show other receiver status messages such as software revision levels of the CPU Card.

– Program the D6600/D6100IPv6 using the front panel keypad or through the COM4 port with the D6200 Programming Software package.

– The Conettix D6600/D6100IPv6 support data network communications including an

	account database capacity of up to 3200 accounts with the optional Conettix D6201 IP
	Security Key.
	– The D6600/D6100IPv6 works with the following Bosch Security Systems, Inc. control
	panels (referred to throughout this manual as “Bosch control panels”): D9412GV3/
	D7412GV3/D7212GV3, D9412GV2/D7412GV2/D7212GV2, D9412G/D7412G/D7212G/
	D9412/D7412/D7212, and D911.
3.1	Parts List

Conettix D6600 System Components

–One Conettix D6600 Communications Receiver/Gateway

–One AC power cord

–One Battery cable P6601

–I/O cable P6602

–Two rack mount brackets

–Four 8/32 phillips-head screws

–One CD-ROM D6200CD

The D6X00 README.TXT file on the CD lists the installation files contained on the CD.

Conettix D6100IPv6 System Components

–Conettix D6100IPv6 Communications Receiver/Gateway

–18 VAC transformer

–Battery cable P6601

–I/O cable P6602

–CD-ROM D6200CD

The D6X00 README.TXT file on the CD lists the installation files contained on the CD.

2012.11 | 08 | 4998122704

Installation and Operation Guide

Bosch Security Systems, Inc.

	Conettix Communications Receiver/	Quick Installation | en 11
	Gateway

4 Quick Installation

D6600

1.Place the D6600 in a secure location.

2.Remove the tie wrap from the receiver door handle. Open the door and remove the packaging foam from the front of the CPU Card.

3.Gently push the CPU and line cards into their slots until they connect securely.

4.Ensure that the D6600 power switch is in the OFF position.

5.Plug the AC power cord into the rear of the D6600.

6.Plug the other end into an unswitched 100 to 120 VAC (or 220 to 230 VAC), 50 to 60 Hz line.

7.Refer to the figure AC Power and Telephone Connections, page 12. Plug the telephone lines into the connectors on the first line terminator card.

8.If you need a network automation connection, skip this step and continue with the remainder of the installation. For additional instructions on connecting automation software to the network, refer to Network Communications, page 42. Refer to the figure

Automation PC and External Parallel Printer Connections, page 12. Connect the automation computer (callout 1) to COM3 the center DB-9 connector on the CPU terminator card, using a null-modem cable (callout 2).

9.Refer to the figure Automation PC and External Parallel Printer Connections, page 12. Connect an external parallel printer, with the power off (callout 4), to the lower 25-pin connector on the CPU terminator card (callout 5).

10.Turn the power switch on the D6600 to the ON position.

11.Press the UP button to increase display contract. Press the Down button to decrease display contrast.

12.Press the Menu button to enter the menu.

13.On the Enter Password screen, type 6600 (default password).

14.Press the Enter button to enter the menu. Use these keys to operate the D6600 menus: Enter – Enter a menu level

Cancel– Return to the previous menu level UP/Down arrow – Scroll through the menus

15.Set the Time and Date on the D6600 (refer to Setting the Time and Date, page 13).

16.The D6600 is ready to accept calls.

D6100IPv6

1.Place the D6100IPv6 in a secure location (such as a rack mount or desktop).

2.Refer to the figure AC Power and Telephone Connections, page 12. Plug telephone lines into the connectors on the back of the D6100IPv6.

3.If you need a network automation connection, skip this step and continue with the remainder of the installation. For additional instructions on connecting automation software to the network, refer to Network Communications, page 42. Refer to the figure

Automation PC and External Parallel Printer Connections, page 12. Connect the automation computer (callout 1) to COM3, the DB-9 connector using a null-modem cable (callout 2).

4.Refer to the figure Automation PC and External Parallel Printer Connections, page 12. Connect an external parallel printer (callout 4), with the power off, to the 25-pin connector (callout 6).

5.Connect the transformer leads to the 18 VAC terminals and plug the other end into the power source.

Bosch Security Systems, Inc.

Installation and Operation Guide

2012.11 | 08 | 4998122704

	12 en | Quick Installation	Conettix Communications Receiver/
		Gateway

6.Press the Up to increase the display contrast. Press the Down arrow to decrease the display contrast.

7.Press the Menu button to enter the menu.

8.On the Enter Password screen, type 6100 (default password).

9.Press the Menu button to enter the menu.

Use these keys to operate the D6100IPv6 menus: Menu – Enter a menu level

Cancel – Return to the previous menu level Up/Down arrow – Scroll through the menus

10.Set the Time and Date on the D6100IPv6 (refer to Setting the Time and Date, page 13).

11.The D6100IPv6 is ready to accept calls.

AC Power and Telephone Connections

D6600

D6100IPV6

Figure 4.1: AC Power and Telephone Connections

Callout Description

1 Telephone connection

2 AC power terminals

3 AC power connector

Automation PC and External Parallel Printer Connections

D6100IPV6

D6600

Figure 4.2: Automation PC and External Parallel Printer Connections

2012.11 | 08 | 4998122704

Installation and Operation Guide

Bosch Security Systems, Inc.

	Conettix Communications Receiver/	Quick Installation | en 13
	Gateway

Callout Description

1 Automation PC

2 COM3 9-pin port (D6600)

3 COM3 9-pin port (D6100IPv6)

4 Parallel printer

5 25-pin parallel port (D6600)

6 25-pin parallel port (D6100IPv6)

4.1	Setting the Time and Date

Notice!

The Time and Date display format is determined by the programming for Menu Item 2.2.3 Set Country.

Time Setup D6600/D6100IPv6

1.Press the Enter button to go to the log in screen.

2.Enter the password (6600 – default password).

3.Press the Enter button to go to the 1 Event Database

4.Press the Down button to go to 2 CPU Configuration.

5.Press the Enter button to go to 2.2 Global.

6.Press the Enter button to go to 2.2.1 Time Setup.

7.Press the Enter button to go to Set Time.

8.Enter the current time.

9.Press the Enter button to go to 2.2.1 Time Setup/New Time Set…

10.Press the Cancel button to return to the previous level.

Date Setup D6600/D6100IPv6

1.Press the Enter button to go to the log in screen.

2.Enter the password (6600 – default password).

3.Press the Enter button to go to the 1 Event Database.

4.Press the Down button to go to 2 CPU Configuration.

5.Press the Enter button to go to 2.2 Global.

6.Press the Enter button to go to 2.2.2 Date Setup.

7.Press the Enter button to go to Set Date.

8.Enter the current time.

9.Press the Enter button to go to 2.2.2 Date Setup/Current Setting…

10.Press the Cancel button to return to the previous level.

Bosch Security Systems, Inc.

Installation and Operation Guide

2012.11 | 08 | 4998122704

	14 en | Card Functions and Locations	Conettix Communications Receiver/
		Gateway

5	Card Functions and Locations
5.1	D6600 Front Panel
	1	2

Figure 5.1: D6600 Communications Receiver/Gateway (Front View)

Callout Description

1 LCD – shows up to 80 characters of information (two lines of up to 40 characters each).

2 Keypad – the D6600 has a 20-button keypad.

The table below shows and defines the D6600/D6100IPv6 Power LEDs.

	2.234		Present	Power LED Status
	Battery	A	Battery	Green	Clear
	Supervision
		C
			Solid	Blinking
	On	X	X
		X
			X
	Off	X	X
		X

2012.11 | 08 | 4998122704

Installation and Operation Guide

Bosch Security Systems, Inc.

	Conettix Communications Receiver/	Card Functions and Locations | en 15
	Gateway

X

Table 5.1: Power LED Indications

The figure below shows and defines the D6600/D6100IPv6 System Trouble LEDs.

System Trouble LED Status

Solid Red or Yellow

Clear

No System Trouble

Any System Trouble*

* Refer to Appendix B: D6600/D6100IPv6 Internal Messages in the D6600/D6100IPv6 Computer Interface Manual (P/N: 4998122703). The following items cause system trouble. The items indicated by ** can be enabled or disabled. If they are disabled, they will not cause a system trouble condition.

	Battery Missing**		External Printing Error**
	UPS AC Fail**		Line Fault**
	Battery Bad**		COM# Error**
	UPS Battery Low**		Line Card Trouble**
	AC Fail		COM3 Trouble**
	System Temperature High
	Table 5.2: System Trouble LED
5.2	Line Cards and Modules
	Name	Model		Description
	Telephone line card	D6640		Legacy Card:
				Up to eight line cards can be installed in
				one D6600 Receiver, for up to 32
				telephone line connections.
	Telephone line card	D6641		Functions like the D6640. Includes
				improved Public Switched Telephone
				Network (PSTN) processing, additional
				memory for future enhancements such as
				VoIP Compensation, and single firmware
				upgrade package.
	CPU card	D6610		The D6600 uses one CPU card. The CPU
				card takes the incoming information from
				the line card and routes the information
				to an automation port, the LCD on the
				front of the receiver, and an external
				printer.

Bosch Security Systems, Inc.

Installation and Operation Guide

2012.11 | 08 | 4998122704

	16 en | Card Functions and Locations	Conettix Communications Receiver/
		Gateway

	Power supply modules	D6630 and	The power supply modules regulate the
		D6631	power used by the D6600. These are not
			field serviceable.
	Telephone line terminator	D6645	Located behind the line card, the
	card		telephone line terminator card isolates
			and protects the line card against outside
			voltage surges that might come over the
			telephone line. Each line card must have a
			line terminator card.
	CPU terminator card	D6615	Located behind the CPU card, the CPU
			terminator card provides the D6600 with
			two serial ports (COM3 and COM4), a
			parallel port (parallel printer), and a
			general I/O port (I/O). The serial ports
			can be used for computer automation, PC
			connection for programming, or a network
			connection with a Network Ethernet
			Module (see specific installation guide
			supplied with your product).
	Table 5.3: D6600 Line Cards and Modules
5.3	D6600 Rear View

The D6600 has input and output pin connector sockets for up to eight line cards, network option (if installed), and one CPU card. It also has slots for connecting these cards to their corresponding terminator cards.

	1	2	3
Bosch Security Systems
Fairport, NY	USA
			1
			2
			3
			4
	B
	A
	T
	T
	E
	R
	Y
	Input:
	100 - 120/
	220 - 240V~
	50 - 60 Hz
	2.5 Amps

Figure 5.2: D6600 Communications Receiver/Gateway (Rear View)

Callout Description

1 Blank plate and location of optional Conettix D6672 COM1 Expansion Kit

2 Conettix D6615 CPU Terminator Card

3 Card slot covers

4 Conettix D6645 Line Terminator Card

2012.11 | 08 | 4998122704

Installation and Operation Guide

Bosch Security Systems, Inc.

	Conettix Communications Receiver/	Card Functions and Locations | en 17
	Gateway

5.3.1 D6600 Internal View

Figure 5.3: Receiver Card Placement

Callout Description

1 Conettix D6645 Telephone Line Terminator Card

2 Backplane

3 Conettix D6615 CPU Terminator Card

4 D6630 AC/DC Power Supply (not serviceable)

5 Conettix D6610 CPU Card

6 D6631 AC/DC Power Supply (not serviceable)

7 Card guides

8 Conettix D6640/D6641 Telephone Line Card

9 Direction of receiver front

Bosch Security Systems, Inc.

Installation and Operation Guide

2012.11 | 08 | 4998122704

	18 en | Card Functions and Locations	Conettix Communications Receiver/
		Gateway

5.4	D6100IPv6 Front Panel
	1	2

POWER

SYSTEM

TROUBLE

COMMUNICATIONS RECEIVER/GATEWAY

Figure 5.4: D6100IPv6 Communications Receiver/Gateway (Front View)

Callout Description

1 Liquid crystal display (LCD) - Displays up to 80 characters of information (two lines of up to 40 characters each).

2 23-button keypad.

5.5	D6100IPv6 Rear View
	Line Cards and Modules
	The D6100IPv6 does not use the same line cards and modules as the D6600. These functions
	are built in.
																		1
																1		2

7

6

5

4

3

2

Figure 5.5: D6100IPv6 Communications Receiver/Gateway (Rear View)

Callout Description

1 Telephone line connections

2 Input/output ports

3 COM RS-232 port

4 COM3 auxiliary RS-232 port

5 Parallel port connection

6 Ethernet port (D6100IPv6 only)

7 USB port

8 Power connection terminal block

2012.11 | 08 | 4998122704

Installation and Operation Guide

Bosch Security Systems, Inc.

	Conettix Communications Receiver/	D6600 Specific Cards | en 19
	Gateway

6	D6600 Specific Cards
6.1	D6640/D6641 Line Cards and D6645 Line Terminator Cards
	Notice!

Starting with D6200 v2.0 the D6640 Line Card is no longer be supported. Information about the D6640 is provided in this section for legacy support only.

Figure 6.1: D6640/D6641 Line Card

Callout Description

1 48-pin connection to D6645 Line Termination Card

2 40-pin connection to D6600 Back Plate

3 LEDs (Refer to D6640/D6641 LED Descriptions, page 20)

Bosch Security Systems, Inc.

Installation and Operation Guide

2012.11 | 08 | 4998122704

	20 en | D6600 Specific Cards	Conettix Communications Receiver/
		Gateway

Figure 6.2: D6645 Line Terminator Card

Callout Description

1 48-pin connection to D6640/D6641 Line Card.

2 Alignment Guide - Stabilizes the connection and acts as a guide for connecting the terminator card to the line card.

3 Telco Line Jacks - Standard telephone lines connect to the RJ11C jacks.

6.1.1	D6640/D6641 LED Descriptions
	Each LED represents a line. For example, LED 1 is for line 1. The LED is active until the system
	acknowledges the entire transmission and the telephone line is ready to receive signals. The
	following table describes LED patterns and colors, and their indications.
		Flash Pattern (Color)					Function
		Flashes (green)					An incoming call is ringing.

The receiver is online.

ON Steady (green)

ON Steady (red or yellow)

The line card detects a line fault condition.

The line card is ready to receive signals, or is

disabled.

OFF

Table 6.1: LED Descriptions

6.2

Card Installation

Warning!

!Discharge static electricity from your body by touching the receiver’s internal frame (unpainted section) before handling any circuit card.

2012.11 | 08 | 4998122704

Installation and Operation Guide

Bosch Security Systems, Inc.

	Conettix Communications Receiver/	D6600 Specific Cards | en 21
	Gateway

Installing Terminator Cards

Refer to D6640/D6641 Line Cards and D6645 Line Terminator Cards, page 19 when performing the following steps:

1.Remove the two bracket screws that secure the terminator card (or card slot cover, if this is a new terminator card installation) to the back of the D6600 chassis.

2.If you are removing an existing terminator card, open the display door on the front of the D6600 and pull the line card slightly out, then re-insert. This will push the existing terminator card out the back of the D6600 chassis.

3.Remove the existing terminator card. Insert the new terminator card in the same slot by aligning the top and bottom of the terminator card with the card guides in the D6600 chassis.

4.Slide the card into the D6600 chassis, wiggling the card as you push until the card is flush with the back of the chassis.

5.Secure the bracket screws at the top and bottom of the terminator card. Ensure that the screws are tight.

6.Repeat this process for all additional terminator cards.

7.Connect appropriate telephone line cords to the telephone line jack on the terminator cards.

8.Continue to Installing Line Cards, page 21.

Notice!

Even if you are replacing an existing terminator card, you must proceed to Installing Line Cards.

Figure 6.3: Removing and Installing the Terminator Card

Callout Description

1 Terminator Card (D6645 shown)

2 Bracket screws (top and bottom)

3 Empty slot

4 D6600 chassis

Installing Line Cards

1.Install the terminator card(s) (Refer to Installing Terminator Cards, page 21).

Bosch Security Systems, Inc.

Installation and Operation Guide

2012.11 | 08 | 4998122704

22 en | D6600 Specific Cards			Conettix Communications Receiver/
				Gateway
	2.	Open the display door on the D6600. One telephone line card is installed in the D6600
		when the unit is shipped from the factory.
	3.	Insert the new line card into the slot by aligning the top and bottom of the line card with
		the card guides in the D6600 chassis. Firmly push the card to make sure it is fully
		connected.
	4.	If you are installing a new telephone line card, remove the appropriate snap-in covers
		from the front of the panel.
	5.	Close the front panel.
	6.	Program the line card if necessary.
		When the line card is initialized (as indicated by a printer report), the settings in the line
		card programming section automatically load into the card.
	7.	Connect communication lines to the line card.
	D6640/D6641 Telephone Line Monitoring
	Each line on the line card continuously monitors the telephone line voltage whether on-hook
	or off-hook. If the voltage on a line falls below 1.8 VDC a Line Trouble indication is generated
	and when it rises above 2.5 VDC it generates a restoral for this line.
6.3	D6610 CPU Card and D6615 CPU Terminator Card

The CPU card connects to the user interface on the front of the D6600 using a 50-pin ribbon cable socket.

Figure 6.4: D6615 CPU Terminator Card

Callout Description

1 Alignment Guide - Stabilizes the connection and acts as a guide for connecting the terminator card to the CPU card.

2 COM3 Automation Computer Port - An auxiliary RS-232 port for connecting to a computer terminal or an automation computer. For SIA/6500 Mode Automation Format reporting, use a null-modem cable to connect to a computer.

3 COM4 RS-232 Port - Connection to a computer running the D6200 programming software.*

2012.11 | 08 | 4998122704

Installation and Operation Guide

Bosch Security Systems, Inc.

	Conettix Communications Receiver/	D6600 Specific Cards | en 23
	Gateway

4 Parallel Printer Port.

* Use a null-modem cable to connect directly to the computer. You can also connect this port to a Network Ethernet Module for communicating over a network.

6.4	Card Removal and Replacement

Warning!

!Remove power to the D6600 before removing, replacing, or installing the CPU card (D6610) or CPU terminator card (D6615).

Removing the CPU Card

1.Remove power to the receiver (refer to Removing Power to the Receiver, page 26).

2.Carefully grasp the plastic grip on the CPU card. Slide it 2 in to 3 in (50 mm to 75 mm) out of the enclosure.

3.Unplug the 50-pin ribbon cable connecting the user interface card to the CPU card. Be careful not to bend the board when disconnecting this cable. Grasp the plastic plug connected to the CPU board at the end of the cable and gently pull it away from the circuit board.

4.Pull the CPU card straight out of the card guide.

Replacing the CPU Card

1.Remove power to the receiver (refer to Removing Power to the Receiver, page 26).

2.Remove the defective CPU card from the enclosure.

3.Align the top and bottom of the CPU card with the card guides. Slide the card into the enclosure, leaving 2 to 3 in (50 mm to 75 mm) out to connect the ribbon cable.

4.Connect the ribbon cable to the CPU card. Orient the cable so the red stripe is up, and slide the card the remaining distance into the enclosure.

5.Restore power to the receiver.

Bosch Security Systems, Inc.

Installation and Operation Guide

2012.11 | 08 | 4998122704

	24 en | Printer Specifications	Conettix Communications Receiver/
		Gateway

7 Printer Specifications

Notice!

Refer to the appropriate Installation Supplement included with your product for the specifics of your particular installation.

Use the DB25 port on the back of the D6600/D6100IPv6 rear panel to connect to a standard parallel text printer.

2012.11 | 08 | 4998122704

Installation and Operation Guide

Bosch Security Systems, Inc.

	Conettix Communications Receiver/	Installation | en 25
	Gateway

8	Installation
	Notice!
	Refer to the appropriate Installation Supplement included with your product for the specifics
	of your particular installation.
8.1	Installation Check List

Check each receiver card to see that it is correctly positioned in the card guides at the top and bottom of the enclosure. Also confirm that connections did not loosen during shipment (D6600 only).

Check each receiver card to see that it is correctly positioned in the card guides at the top and bottom of the enclosure. Also confirm that connections did not loosen during shipment (D6600 only).

Ensure that the earth ground is connected and grounded through the AC inlet.

If you are installing additional line cards, install the terminator cards now (D6600 only).

After installing additional line terminator cards, install the line cards (refer to Card Installation, page 20).

Install the line terminator card(s) from your spares package(s). If there is a malfunction, you can quickly switch over to the replacement card (refer to Card Installation, page 20).

Notice!

You can install spare line terminator cards. Do not install spare line cards.

Connect four or six conductor telephone cord(s) to the RJ11C jack(s) of the desired telephone line(s). Plug the other end of the modular telephone cord(s) into the telephone jack on the appropriate line terminator card(s).

Connect the supplied AC transformer wiring leads to the AC terminals on the rear of the D6100IPv6.

Plug the AC cord (D6600 only) into a correctly wired 120 VAC, 60 Hz or 220 VAC, 50 Hz outlet (standard AC outlet).

Notice!

Maintain a 6.5 mm (0.25 in) gap, or greater, between power limited and non-power limited circuit wiring.

Plug the AC transformer into the correctly wired wall receptacle that matches the voltage of the transformer.

Bosch Security Systems, Inc.

Installation and Operation Guide

2012.11 | 08 | 4998122704

	26 en | Installation	Conettix Communications Receiver/
		Gateway

Notice!

Ensure that a switch does not control the outlet.

Turn the D6600 power switch on. The D6100IPv6 starts as soon as you plug in the AC

	Transformer.
			Set the calendar and clock to the correct date and time and program the necessary
	options.
			Ensure that the communication formats are correct by having communicators send test
	reports to each line connected to the receiver.
8.2	Rack Mount Instructions
	Refer to the specific installation guide supplied with your product.
8.3	Removing Power to the Receiver
	1.		Remove the battery power connection.
	2.		Turn off the AC power on the D6600 or unplug the D6100IPv6 AC transformer.
	3.		Unplug the AC cord from the outlet.

Warning!

Do not try to restart the D6600/D6100IPv6 with a fully discharged battery. Reconnect after

!you apply power. To prevent deep battery discharge, use a D135A Low Battery Cutoff Module. Refer to the D135A Installation Guide (P/N: 74-06499-000) for more information.

Notice!

If programmable Output 1 or 2 is activated by automation failure, you cannot clear Output 1 or 2 by pressing the Acknowledge key.

2012.11 | 08 | 4998122704

Installation and Operation Guide

Bosch Security Systems, Inc.

	Conettix Communications Receiver/	Power | en 27
	Gateway

9	Power
9.1	Power Supply Modules
9.2	Main Power
	D6600 Power Input
	AC Nominal Operating Range		120 V or 230 V
	AC maximum Operating Range		100 VAC to 120 VAC, 220 VAC to 240 VAC, 50–60 Hz
			2.5 A maximum
	Power Cord		IEC 60320 C13 type
	Replaceable Fuse		2.5A F250V Fast blow 5x20mm
	D6100IPv6 Power Input
	AC Nominal Operating Range		18VAC (Refer to the specific Installation Supplement
			supplied with your product for your application for
			supplied transformer specifics)
9.3	Standby Power
	Notice!
	Refer to the appropriate Installation Supplement included with your product for the specifics
	of your particular installation.
	During a loss of AC power, the receiver automatically switches to standby power. External
	batteries or an uninterruptible power supply (UPS) provides standby power. As long as there
	is adequate standby power, the receiver’s operation is not interrupted, even if the power loss
	occurs during signal processing. When power supervision is enabled and a loss of AC power
	occurs, the primary reporting devices (such as printers and computers) show AC FAIL and the
	D6600/D6100IPv6 power indicator starts blinking. When AC power restores, the power
	indicator stops blinking and reporting devices show AC RESTORE.
9.4	Connecting External Batteries

Notice!

Do not connect an external battery charger to the D6600/D610IPv6 or its battery. There is a risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.

Use the terminal on the rear panel to connect an external DC power source. During AC power outages, the external DC source supplies power to the receiver. Use a 12 VDC, 7 to 18 Ah lead-acid battery for external backup power.

	Battery Voltage	Display during AC power	Display if no battery when
		outage	AC power is restored
	Above 11.5 V	Battery OK

Bosch Security Systems, Inc.

Installation and Operation Guide

2012.11 | 08 | 4998122704