Beko WMD 66160, WMD 66140, WMD 66120 S, WMD 66140 S, WMD 66120 User Manual [nl]

Washing Machine

Lave-linge

Wasmachine

Waschmaschine

WMD 66160 WMD 66140 S WMD 66140 WMD 66120 S WMD 66120

1 Warnings

General Safety

•Never place your machine on a carpet covered floor. Otherwise, lack of airflow from below of your machine may cause electrical parts to overheat. This may cause problems with your washing machine.

•If the power cable or mains plug is damaged you must call Authorized Service for repair.

•Fit the drain hose into the discharge housing securely to prevent any water leakage and to allow machine to take in and discharge water as required. It is very important that the water intake and drain hoses are not folded, squeezed, or broken when the appliance is pushed into place after it is installed or cleaned.

•Your washing machine is designed to continue operating in the event of a power interruption. Your machine will not resume its program when the power restores. Press the “Start/Pause/Cancel” button for 3 seconds to cancel the program (See, Canceling a Program)

•There may be some water in your machine when you receive it. This is from the quality control process and is normal. It is not harmful to your machine.

•Some problems you may encounter may be caused by the infrastructure. Press "Start/Pause/Cancel" button for 3 seconds to cancel the program set in

your machine before calling the authorized service.

First Use

•Carry out your first washing process without loading your machine and with detergent under “Cottons 90°C” program.

•Ensure that the cold and hot water connections are made correctly when installing your machine.

•If the current fuse or circuit breaker is less than 16 Amperes, please have a qualified electrician install a 16 Ampere fuse or circuit breaker.

•While using with or without a transformer, do not neglect to have the grounding installation laid by a qualified electrician. Our company shall not be liable for

any damages that may arise when the machine is used on a line without grounding.

•Keep the packaging materials out of reach of children or dispose them by classifying according to waste directives.

Intended use

•This product has been designed for home use.

•The appliance may only be used for washing and rinsing of textiles that are marked accordingly.

Safety instructions

•This appliance must be connected to an earthed outlet protected by a fuse of suitable capacity.

•The supply and draining hoses must always be securely fastened and remain in an undamaged state.

•Fit the draining hose to a washbasin or bathtub securely before starting up your machine. There may be a risk of being scalded due to high washing temperatures!

•Never open the loading door or remove the filter while there is still water in the drum.

•Unplug the machine when it is not in use.

•Never wash down the appliance with a water hose! There is the risk of electric shock!

•Never touch the plug with wet hands. Do not operate the machine if the power cord or plug is damaged.

•For malfunctions that cannot be solved by information in the operating manual:

•Turn off the machine, unplug it, turn off the water tap and contact an authorized service agent. You may refer to your local agent or solid waste collection center in your municipality to learn how to dispose of your machine.

If there are children in your house...

•Keep children away from the machine when it is operating. Do not let them tamper with the machine.

•Close the loading door when you leave the area where the machine is located.

2 - EN

2 Installation

Removing packaging reinforcement

Tilt the machine to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon.

Opening the transportation locks

ATransportation safety bolts must be removed before operating the washing machine! Otherwise, the machine will be damaged!

1.Loosen all the bolts with a spanner until they rotate freely (“C”)

2.Remove transportation safety bolts by turning them gently.

3.Fit the covers (supplied in the bag with the Operation Manual) into the holes on the rear panel. (“P”)

seals should be used at the tap and machine connection ends of the hoses. The plain end of the hose fitted with a filter must be attached to the tap and the elbowed end must be attached to the machine. Tighten the nuts of the hose well by hand; never use wrenches to tighten the nuts.

•Models with a single water inlet should not be connected to the hot water tap.

When returning the appliance to its place after maintenance or cleaning, care should be taken not to fold, squeeze or block the hoses.

C Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future.

C Never move the appliance without the transportation safety bolts properly fixed in place!

Adjusting the feet

ADo not use any tools to loosen the lock nuts. Otherwise, they can be damaged.

1.Manually (by hand) loosen the lock nuts on the feet.

2.Adjust them until the machine stands level and firmly.

3.Important: Tighten all lock nuts up again.

Connecting to the water supply.

Important:

•The water supply pressure required to run the machine must be 1-10 bar (0,1 – 1 MPa).

•Connect the special hoses supplied with the machine to the water intake valves on the machine.

•In order to prevent water leakage that may occur at the connection points, there are rubber seals (4 seals for the models with double water inlet and 2 seals for other models) attached to the hoses. These

Connecting to the drain

The water discharge hose can be attached to the edge of a washbasin or bathtub. The drain hose should be firmly fitted into the drain as to not get out of its housing.

Important:

•The end of the drain hose must be directly connected to the wastewater drain or to the washbasin.

•The hose should be attached to a height of at least 40 cm, and 100 cm at most.

•In case the hose is elevated after laying it on the floor level or close to the ground (less than 40 cm above the ground), water discharge becomes more difficult and the laundry may come out wet.

•The hose should be pushed into the drainage for more than 15 cm. If it is too long you may have it shortened.

•The maximum length of the combined hoses must not be longer than 3.2 m.

Electrical connection

Connect the machine to an earthed outlet protected by a fuse of suitable capacity. Important:

• Connection should comply with national

3 - EN

regulations.

• The voltage and the allowed fuse protection are specified in the section “Technical Specifications”.

• The specified voltage must be equal to your mains voltage.

• Connection via extension cords or multiplugs should not be made.

BA damaged power cable must be replaced by a qualified electrician.

BThe appliance must not be operated unless it is repaired! There is the risk of electric shock!

3 Initial preparations for washing

Preparing clothes for washing

Laundry items with metal attachments such as, bras, belt buckles and metal buttons will damage the machine. Remove metal attachments or place the items in a clothing bag, pillow case, or something similar.

•Sort the laundry according to type of fabric, color, and degree of soiling and permissible water temperature. Always follow the advice on the garment labels.

•Place small items like infants’ socks and nylon stockings, etc. in a laundry bag, pillow case or something similar. This will also save your laundry from getting lost.

•Wash “machine washable” or “hand washable” labeled products only with an appropriate program.

•Do not wash colors and whites together. New, dark colored cottons may release a lot of dye. Wash them separately.

•Use only dyes/color changers and lime removers suitable for machine wash. Always follow the instructions on the packaging.

•Wash trousers and delicate clothes turned inside out.

Correct load capacity

C Please follow the information in the "Program Selection Table". Washing results will degrade when the machine is overloaded.

Loading door

The door locks during program operation and the Door Locked Symbol (Figure 3-13i) lights up. The door can be opened when the symbol fades out.

Detergents and softeners

Detergent Drawer

The detergent drawer is composed of three compartments:

The detergent dispenser may be in two different types according to the model of your machine.

–(I) for prewash

–(II) for main wash - (III) siphon

–() for softener

Detergent, softener and other cleaning agents

Add detergent and softener before starting the washing program.

Never open the detergent dispenser drawer while the washing program is running!

When using a program without pre-wash, no detergent should be put into the pre-wash compartment (Compartment no. I).

Detergent quantity

The amount of washing detergent to be used depends on the amount of laundry, the degree of soiling and water hardness.

•Do not use amounts exceeding the quantities recommended on the package to avoid problems of excessive foam, poor rinsing, financial savings and finally, environmental protection.

•Never exceed the (> max <) level marking; otherwise, the softener will be wasted without being used.

•Do not use liquid detergent if you want to wash using the time delay feature.

4 - EN

4 Selecting a Program and Operating Your Machine

Control panel

9

8

7

6

5

Deur

Synthetisch

Katoen

openen

Synthétique

60° 90° 60° Coton

Ouverture Wassen

Spoelen

Centrifugeren

de Porte Lavage

Rinçage

Essorage

40°

40°

Start/Pause

30°

30°

Départ/Pause

Sport 40

Super 40

Hemden

Chemise

Mini30

40

Delicaat

60°

Start

Reset

Délicat

Voorwas

Lavage

Rincage

Babycare

30°

Stop

3 sec

Prélavage

Express

Plus

40°

40°

Marche

Annulation

3 sec.

Wassen

Spoelen

Wol

30°

Arrêt

Lavage

Rinçage

Uitgestelde

Centrifugeren

Laine

Spoelen

Express

Plus

start

Essorage

Départ Différé

Rinçage

4

3

2

1

1 - Spin Speed Adjustment Button

7 - Child-proof Lock Indicator*

2 - Time Delaying Button

8 - Program Follow-up Indicators

3

- Auxiliary Function Keys

9 - On/Off Button

4 - Start/Pause/Cancel Button

5 - Program Selection Knob

* According to your machine’s model

6

- Display

Turning the machine on

Plug in your machine. Turn the tap on completely. Check if the hoses are connected tightly. Place the laundry in the machine. Add detergent and softener. Press the “On/Off” button.

Program selection

Select the appropriate program from the program table and the following washing temperature table according to type, amount and degree of soiling of the laundry. Select the desired program with the program selection button.

C Programs are limited with the highest spin speed appropriate for that particular type of cloth.

Main programs

Depending on the type of textile, the following main programs are available:

•Cottons

You can wash your durable clothes with this program. Your laundry will be washed with vigorous washing movements during a longer washing cycle.

•Synthetics/Mix

You can wash your less durable clothes on this program. Lighter washing movements

and shorter washing cycle is used compared to “Cottons” program. It is recommended for your synthetic clothes (such as shirts, blouses, synthetic/cotton blended garments, etc.). For

curtains and lace, the “Synthetic(mix)40” program with pre-wash and anti-creasing functions selected is recommended.

•Woolens

You can wash your machine-washable woolen garments on this program. Wash by selecting the proper temperature according to the labels of your clothes. It is recommended to use appropriate detergents for woolens.

Additional programs

For special cases, there are also extra programs available:

• Delicates

You can wash your delicate clothes on this program. It has more sensitive washing movements and does not make intermediate spinning compared to “Synthetic” program.

• Shirt

You can use this program to wash cottons and synthetics together. There is no need to sort them.

5 - EN

• Sport

This program is suitable for clothes that are normally worn for a short time such as

sportswear. It is used to quickly wash a small amount of cotton/synthetic blended clothes.

• Super

This program washes for a longer period at 40°C and gives the same result as the “Cottons 60°C” program, thus it saves energy. It is suitable for clothes for which you cannot use the “Cottons 60°C” program.

• Mini

This program is used to quickly wash (30 minutes) a small amount of lightly soiled cotton garments.

• Babycare

Increased hygiene is provided by a longer heating period and an additional rinse cycle. It is recommended for baby clothes and clothes worn by allergic people.

• Hand Wash

You can wash your woolen/delicate clothes that bear “not machinewashable” labels for which hand wash is recommended on this program.

It washes the laundry with very tender washing movements without damaging your clothes. C Sort the laundry according to type

of fabric, color, degree of soiling and permissible water temperature when choosing a program.

Special programs

For specific applications, you can select any of the following programs:

• Rinse

This program is used when you want to rinse or starch separately.

• Spin and Pump

This program is used to apply an additional spin cycle for the laundry or to drain the water in the machine.

Before starting this program, select the desired spin sped and press “Start/Pause/Cancel” button. Your machine drains the water after spinning at the set spin speed.

If you only want to drain the water without spinning your laundry, select “Spin and Pump” program, and then select no spin function with spin speed selection button. Press “Start/Pause/ Cancel” button.

AYou should use a lower spin speed for delicate laundries.

Spin Speed selection

Whenever a new program is selected, the maximum spin speed of the selected program is displayed on the spin speed indicator.

To decrease the spin speed, press the “Spin” button. Spin speed decreases gradually. Then, rinse hold and no spin options are shown respectively.

Rinse hold is shown with “” and no spin is shown with “ ” symbols.

If you do not want to unload your clothes

immediately after the program, you may use rinse hold function in order to prevent your clothes become wrinkled in anhydrous conditions. With this function, your laundry is kept in the final rinsing water. If you want to spin your laundry that you left in water:

-Adjust the spin speed.

-Press “Start/Pause/Cancel” button.

Program resumes. Your machine drains the water and spins your laundry.

You can use no spin function in order to drain the water without spinning at the end of the program.

6 - EN

Program and consumption table

		LoadMax.(kg)	800-	rpm	ConsumptionWater (l)	ConsumptionEnergy (kWh)	Prewash	WashQuick	PlusRinse	Creasing-Anti	HoldRinse	HeatNo
			speedSpin 1400	rpm1600 classA(For efficiency)
			(rpm)	1400
Programme				spin
Cottons	90	6	130	136	49	2.18	•	•	•	•	•	•
Cottons	60**	6	135	139	49	1.14	•	•	•	•	•	•
Cottons	40	6	125	136	49	0.66	•	•	•	•	•	•
Super	40	6	161	171	49	0.87					•
Babycare	60	6	164	174	69	1.29			*	•	•	•
Sports	40	3	75	75	47	0.56	•	•	•	•	•	•
Synthetics	60	3	103	103	50	0.95	•	•	•	•	•	•
Synthetics(mix)	40	3	96	96	50	0.73	•	•	•	•	•	•
Shirts	40	3	91	91	48	0.34	•	•	•	•		•
Delicate	30	2	65	65	63	0.28			•	•	•	•
Woollens	40	1.5	60	60	56	0.27			•		•	•
Hand wash	30	1	39	39	41	0.15						•
Mini	30	2.5	30	30	38	0.25						•

• : Selectable

* : Automatically selected, not cancellable. **: Energy Label programme (EN 60456)

Water and power consumption and programme duration may differ from the table shown, subject to changes in water pressure, water hardness and temperature, ambient temperature, type and amount of laundry, selection of auxiliary functions, and fluctuations in the supply voltage.

“Super 40” programme may be selected instead of “Cotton 60*” programme during winter in areas where the input water temperature is low and/or in areas with low supply voltage.

C The auxiliary functions in the table may differ according to the model of your machine.

7 - EN

Auxiliary functions

Auxiliary Function Selection Buttons

Select the required auxiliary functions before starting the program.

C Some combinations cannot be selected together. (Ex.: Pre-wash and Quick Wash.

Warning signal on the selected auxiliary function will light up.

Auxiliary function selection

If an auxiliary function that should not be selected together with a previously selected function

is chosen, the first selected function will be cancelled and the last auxiliary function selection will remain active.

(Ex.: If you want to select pre-wash first and then quick wash, pre-wash will be cancelled and quick wash will remain active.

Auxiliary function that is not compatible with the program cannot be selected. (see, “Program Selection Table”)

C Auxiliary function buttons may differ according to the model of your machine.

Pre-wash

A pre-wash is only worthwhile for heavily soiled laundry. Without pre-wash you save energy, water, detergent and time.

C Pre-wash without detergent is recommended for lace and curtains.

Quick wash

This function can be used for “Cottons” and “Synthetics” programs. It decreases the washing times for lightly soiled laundries and also the number of rinsing steps.

Rinse Plus

With this function, you can increase the number of current rinsing steps. Thus, sensitive skins’ risk of being affected by the remainder detergent on the clothes will be decreased.

Anti-creasing

With this function, drum movement will be lessened to prevent creasing and spinning speed is limited. In addition, washing is carried out at a higher water level.

C Whenever you select this auxiliary function, load your machine with half of the maximum laundry specified in the program table.

No Heat

If you wish to wash your clothes in cold water, you can use this program.

Time display

The display shows the time remaining for the program to complete while a program is running. Program duration may differ from the values in the consumption table subject to the changes in the water pressure, water hardness and temperature, ambient temperature, type and amount of laundry, auxiliary functions selected, and changes in the supply voltage.

Time delay

With the “Time delay” function you can delay the program start up to 24 hours. Time delay can be set with steps of one hour for the first three hours and with steps of three hours for the remainder (1, 2, 3, 6, 9, …24).

1.Pres “Time Delay” button to adjust the desired time.

2.Press “Start/Pause/Cancel” button. The time delay will start to count down.

C More laundry may be loaded during the

time delay period.

Changing the delay time

If you want to change the time during the countdown:

1.Press “Start/Pause/Cancel” button.

2.Pres “Time Delay” button to adjust the desired time delay.

3.Press “Start/Pause/Cancel” button.

Canceling the time delay

If you want to cancel the time delay countdown and start the program:

1.Press “Start/Pause/Cancel” button.

2.Pres “Time Delay” button to decrease the time delay.

3.Press “Start/Pause/Cancel” button to start the program.

Starting the Program

1.Press “Start/Pause/Cancel” button to start the program.

2.Program follow-up lamp showing the startup of the program will light up.

Progress of program

Progress of a running program is shown through the program follow-up indicator. At the beginning of every program step, the relevant indicator lamp will light up and light of the completed step will turn off. The symbol that is lit up at the far right of the series of symbols indicates the step that is being carried out.

C If the machine is not spinning, the program may be in rinse hold mode or the automatic spin correction system has been activated due to an excessive unbalanced distribution of laundry in the machine.

Changing the selections after the program has started

Turning the program knob while the program is in a normal flow will not change the program.

Switching the machine to standby mode

Press “Start/Pause/Cancel” button momentarily to switch your machine to the standby mode. Auxiliary functions can be cancelled or selected in accordance with the step the program is at. The

8 - EN

door can be opened if the water level is suitable. Laundry may be added / taken out by opening the door.

Door lock

The loading door can not be opened yet due to safety reasons while the “Ready” lamp is flashing. The loading door can be opened once the “Ready” lamp starts lighting up continuously.

5 Maintenance and cleaning

Detergent Drawer

Remove any powder residue buildup in the drawer. To do this;

1.Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine.

Child-proof lock

You can protect the appliance from being tampered by children by means of the child-proof lock. In this case, no change can be made in the running program.

The machine is switched to child-lock by pressing the 1st and 2nd auxiliary functions for 3 sec. “C on” (Child lock is activated) label appears on the screen. The same symbol will also be displayed whenever any button is pressed while the machine is child-locked.

Child-proof lock lamp on the program follow-up indicator will light up when the child-proof lock is activated.

To deactivate the child-proof lock, press the 1st and 2nd auxiliary function buttons for 3 sec. “C OFF” (Child-proof lock is deactivated) symbol appears on the screen. Child-proof lock lamp on the program follow-up indicator will go off when the child-proof lock is deactivated.

Ending the program through canceling

“Start/Pause/Cancel” button is pressed for 3 seconds to cancel the program. “Ready” warning lamp flashes during canceling and “End” will appear on the display.

C If more than a normal amount of water and softener mixture starts to gather in the softener compartment, the siphon must be cleaned.

2.Wash the dispenser drawer and the siphon with plenty of lukewarm water in a washbasin.

3.Replace the drawer into its housing after cleaning. Check if the siphon is in its original location.

Inlet water filters

There is a filter at the end of each water intake valve at the back side of the machine and also at the end of each water intake hose where they are connected to the tap. These filters prevent the foreign substances and dirt in the water to enter into the machine. Filters should be cleaned as they get dirty.

• Close the taps.

•Remove the nuts of the water intake hoses to clean the surfaces of the filters on the water intake valves with an appropriate brush.

•If the filters are very dirty, you can pull them out by means of pliers and clean them.

•Take out the filters on the flat ends of the water intake hoses together with the gaskets and clean thoroughly under streaming water.

•Replace the gaskets and filters carefully to their places and tighten the hose nuts by hand.

9 - EN

Draining any remaining water and cleaning the pump filter

Your product is equipped with a filter system which ensures a cleaner water discharge that extends pump life by preventing solid items such as buttons, coins and fabric fibers from clogging the pump propeller during discharge of the washing water.

•If your machine fails to drain the water, the pump filter may be clogged. You may have to clean it every 2 years or whenever it is plugged. Water must be drained off to clean the pump filter.

In addition, water may have to be drained off completely in the following cases:

•before transporting the machine (e.g. when moving house)

•when there is the danger of frost

In order to clean the dirty filter and discharge the water;

1- Unplug the machine to cut off the supply power.

AThere may be water at 90°C in the machine. Therefore, the filter must be cleaned only after the inside water is cooled down to avoid hazard of scalding.

2- Open the filter cap. The filter cap may be composed of one or two pieces according to the model of your machine.

If it is composed of two pieces, press the tab on the filter cap downwards and pull the piece out towards yourself.

If it is composed of one piece, hold it from both sides and open it by pulling out.

3- An emergency drain hose is supplied with some of our models. Others are not supplied with this item.

If your product is supplied with an emergency drain hose, do the following as shown in the figure below:

•Pull out the pump outlet hose from its housing.

•Place a large container at the end of the hose. Drain the water off into the container

by pulling out the plug at the end of the hose. If the amount of water to be drained off is greater than the volume of the container, replace the plug, pour the water out, then resume the draining process.

•After draining process is completed, replace the plug into the end of the hose and fit the hose back into its place.

If your product is not supplied with an emergency drain hose, do the following as shown in the figure below:

•Place a large container in front of the filter to receive water flowing from the filter.

•Loosen pump filter (anticlockwise) until water starts to flow out of it. Direct the flowing water into the container you have placed in front of the filter. You can use a piece of cloth to absorb any spilled water.

•When there is no water left, turn the pump filter until it is completely loose and remove it.

•Clean any residues inside the filter as well as fibers, if any, around the propeller region.

•If your product has a water jet feature, be sure to fit the filter into its housing in the pump. Never force the filter while replacing it into its housing. Fit the filter fully into its housing; otherwise, water may leak from the filter cap.

4- Close the filter cap.

Close the two-piece filter cap of your product by pushing the tab on it.

Close the one-piece filter cap of your product by fitting the tabs on the bottom into their positions and pushing the upper part of it.

10 - EN

6 Solution suggestions for problems

	Problem	Cause	Explanation / Suggestion
		Machine may have switched to
	Program cannot be	self protection mode due to an	Reset your machine by pressing “Start/Pause/Cancel”
	started or selected.	infrastructure problem (such as	button for 3 seconds. (see, Canceling a Program)
		line voltage, water pressure, etc.).
	There is water		Be sure the seals of the water inlet hoses are securely
	coming from the	There might be problems with	fitted.
	bottom of the	hoses or the pump filter.	Tightly attach the drain hose to the tap.
	machine.		Make sure that the pump filter is completely closed.
	Machine stopped	Machine can stop temporarily	It will resume operating when the voltage is back to the
	shortly after the
		due to low voltage.	normal level.
	program started.
			The automatic spin correction system might have been
			activated due to the unbalanced distribution of the
	It continuously		laundry in the drum.
	spins.	There may be an imbalance of	The laundry in the drum may be clustered (bundled
	Remaining time		laundry in a bag). Laundry should be rearranged and
		laundry in the machine.
	does not count		re-spun.
	down.		No spinning is performed when the laundry is not evenly
			distributed in the drum to prevent any damage to the
			machine and to its environment.
		In the case of a paused
		countdown while taking in water:	The machine will wait until there is a sufficient amount of
		Timer will not countdown until the	water to avoid poor washing results due to lack of water.
		machine is filled with the correct	Then the timer will start to count down.
		amount of water.
		In the case of a paused
		countdown at the heating step:
		Time will not count down until
	It continuously	the selected temperature for the
	washes.	program is reached
	Remaining time
	does not count		The automatic spin correction system might have been
	down.
			activated due to the unbalanced distribution of the
		In the case of a paused	laundry in the drum.
			The laundry in the drum may be clustered (bundled
		countdown at the spinning step:
			laundry in a bag). Laundry should be rearranged and
		There may be an imbalance of	re-spun.
		laundry in the machine.
			No spinning is performed when the laundry is not evenly
			distributed in the drum to prevent any damage to the
			machine and to its environment.

11 - EN

7 Specifications

Models	WMD 66160	WMD 66140 S	WMD 66140	WMD 66120 S	WMD 66120
Maximum dry laundry capacity (kg)	6	6	6	6	6
Height (cm)	84	84	84	84	84
Width (cm)	60	60	60	60	60
Depth (cm)	54	54	54	54	54
Net Weight (kg)	76	76	76	74	74
Electricity (V/Hz.)	230 V / 50hz	230 V / 50hz	230 V / 50hz	230 V / 50hz	230 V / 50hz
Total Current (A)	10	10	10	10	10
Total Power (W)	2200	2200	2200	2200	2200
Spinning cycle (rpm max.)	1600	1400	1400	1200	1200

Specifications of this appliance may change without notice to improve the quality of the product. Figures in this manual are schematic and may not match your product exactly.

Values stated on the machine labels or in the documentation accompanying it are obtained in laboratory in accordance with the relevant standards. Depending on operational and environmental conditions of the appliance, values may vary.

This appliance’s packaging material is recyclable. Help recycle it and protect the environment by dropping it off in the municipal receptacles provided for this purpose. Your appliance also contains a great amount of recyclable material. It is marked with this label to indicate the used appliances that should not be mixed with other waste. This way, the appliance recycling organised by your manufacturer will be done under the best possible conditions, in compliance with European Directive 2002/96/EC on Waste Electrical

and Electronic Equipment. Contact your town hall or your retailer for the used appliance collection points closest to your home. We thank you doing your part to protect the environment.

12 - EN

	1 Avertissements	Utilisation prévue
		• Cet appareil est destiné à un usage
	Sécurité générale
		domestique.
	• Ne jamais installer votre appareil sur un	• L’appareil ne peut être utilisé que pour le
	sol en moquette. Dans le cas contraire,	lavage et le rinçage des textiles indiqués
	le manque d’écoulement d'air par-	comme tel.
	dessous votre machine pourrait entraîner	Consignes de sécurité
	la surchauffe des pièces électriques. Ceci	• L’appareil doit être raccordé à une prise de
	pourrait entraîner des problèmes avec votre
		mise à la terre protégée par un fusible de
	lave-linge.
		capacité adaptée.
	• Si le câble d’alimentation ou la prise
		• Les tuyaux d'alimentation et de vidange
	secteur est endommagé, vous devez faire
		doivent toujours être solidement fermés et
	appel au Service agréé pour réparation.
		conservés dans un bon état.
	• Insérer solidement le tuyau de vidange
		• Insérer solidement le tuyau de vidange
	dans le logement approprié pour éviter une
		à un lavabo ou d'une baignoire avant de
	éventuelle fuite d’eau et pour permettre à la
		mettre votre appareil en route. Vous courez
	machine d'absorber et de vidanger de l’eau
		le risque de vous brûler en raison des
	comme souhaité. Il est très important que
		températures de lavage élevées !
	les tuyaux d'arrivée d'eau et de vidange
		• Ne jamais ouvrir la porte ou ouvrir le filtre
	ne soient pas dépliés, coincés, ou cassés
		alors qu’il y a encore de l’eau dans le
	lorsque l’appareil est inséré à l’endroit une
		tambour.
	fois installés ou nettoyés.
		• Débranchez la machine lorsque celle-ci
	• Votre lave-linge a été conçu pour
		n’est pas en cours d’utilisation.
	continuer à fonctionner en cas de coupure
		• Ne jamais nettoyer l’appareil à l’aide d’un
	d’électricité. Votre machine ne reprendra
		tuyau d’arrosage ! Il y a un risque de
	pas son programme une fois le courant
		décharge électrique !
	rétabli. Appuyez sur le bouton « Départ/
		• Ne jamais toucher la prise avec les mains
	Pause/Annulation » pendant 3 secondes
		mouillées. Ne pas mettre la machine en
	pour annuler le programme (voir Annuler un
		marche si le cordon d’alimentation ou la
	programme).
		prise est branchée.
	• Il pourrait rester un peu d’eau dans votre
		• Pour des dysfonctionnements qui ne
	machine après que vous l’avez reçue. Ce
		peuvent être résolus grâce aux informations
	phénomène, qui fait suite au processus
		fournies dans le manuel:
	d’assurance qualité, est tout à fait normal.
		• éteignez la machine, débranchez-la, fermez
	Ceci n’affecte pas votre machine.
		le robinet d’arrivée d’eau et contactez
	• Quelques problèmes que vous pouvez
		un agent du service agrée. Vous pouvez
	rencontrer peuvent être provoqués par
		consulter votre agent local ou le centre
	les infrastructures. Appuyez sur le bouton
		de collecte des déchets solides de
	« Départ/Pause/Annulation » pendant 3
		votre municipalité pour en savoir plus
	secondes pour annuler le programme défini
		sur la procédure à suivre afin de vous
	dans votre machine, avant de contacter le
		débarrasser de votre machine.
	service agrée.
		S’il y a des enfants chez vous…
	Première mise en service
		• Tenez les à l’écart de la machine lorsque
	• Lancez votre premier programme de lavage	celle-ci fonctionne. Ne leur donnez pas la
	pour coton en dessous de 90°C sans
		permission de toucher à la machine.
	charge et avec du détergent.
		• Fermez la porte au moment de quitter
	• Assurez-vous que les raccordements d’eau
		l’endroit où se trouve la machine.
	froide et d’eau chaude sont effectués
	correctement lors de l’installation de votre
	machine.

•Si le fusible du courant ou le disjoncteur est inférieur à 16 ampères, veuillez demander

àun électricien qualifié d'installer un fusible de 16 ampères ou un disjoncteur.

•Que vous utilisiez un transformateur ou non, ne négligez pas de demander à un électricien qualifié d'effectuer l’installation de mise à la terre. Notre société ne

sera pas tenue responsable pour tous dommages qui pourraient survenir si la machine est utilisée sur un circuit sans mise

àla terre.

•Mettez les matériaux d’emballage hors de portée des enfants ou débarrassez-vous- en, en les classant conformément aux directives sur les déchets.

14 - FR

2 Installation

Retirer les renforts de conditionnement

Inclinez la machine pour retirer le renfort de conditionnement. Retirer le renfort de conditionnement en tirant sur le ruban.

Ouvrir les sécurités de transport

ALes vis de sécurité réservées au transport doivent être enlevées avant de faire fonctionner le lave-linge ! Dans le cas contraire, la machine sera endommagée !

1.Desserrez toutes les vis à l’aide d’une clé jusqu’à ce que celles-ci tournent librement (« C »)

2.Enlevez les vis de sécurité en les dévissant à la main et en les tournant doucement.

3.Insérez les cache-orifices (fournis dans le sachet avec le manuel) dans les trous à l’arrière du panneau. (« P »)

C Conservez les vis de sécurité soigneusement afin de les réutiliser au cas où vous aurez besoin de transporter le lave-linge ultérieurement.

C Ne jamais déplacer l'appareil sans que les vis de sécurité réservées au transport ne soient correctement fixées!

Ajuster les pieds

AN’utiliser aucun outil pour dévisser les contre-écrous. Sinon, vous pouvez les endommager.

1.Dévissez manuellement (à la main) les contre-écrous sur les pieds.

2.Ajustez-les jusqu’à ce que la machine soit à niveau et équilibré.

3.Important : Resserrez tous les contreécrous.

les modèles à double admission d’eau et 2 joints pour les autres modèles) sont

attachés aux tuyaux. Ces joints doivent être utilisés sur le robinet et aux extrémités de raccordement des tuyaux L’embout mâle du tuyau muni d’un filtre doit être raccordé au robinet et l’embout coudé doit être attaché à la machine. Serrez correctement les écrous du tuyau à la main ; ne jamais utiliser de clé à molette pour le faire.

•Les modèles à simple admission d’eau ne doivent pas être connectés au robinet

d’eau chaude.

Au moment de retourner l’appareil à sa place après entretien ou nettoyage, des précautions doivent être prises afin de ne pas déplier, coincer, ou bloquer les tuyaux.

Raccorder le conduit d’évacuation

Le tuyau de vidange peut être attaché au bord d’un évier ou d’une baignoire. Le tuyau de vidange doit être correctement raccordé au conduit d’évacuation de sorte qu’il ne puisse pas sortir de son logement.

Important :

•L’extrémité du tuyau de vidange doit être directement raccordée au tuyau

d’évacuation des eaux usées ou au lavabo.

•Le tuyau doit être attaché à une hauteur comprise entre 40 et 100 cm.

Raccorder l’arrivée d’eau.

Important:

•La pression d’eau à l’arrivée, requise pour faire fonctionner la machine, doit être de 1-10 bar (0,1 – 10 Mpa).

•Raccordez les tuyaux spéciaux fournis avec la machine aux vannes d’admission d’eau de la machine.

•Pour éviter qu’une fuite d’eau ne se produise aux points de raccordement, des joints en caoutchouc (4 joints pour

•Si le tuyau est élevé après l’avoir posé sur le niveau du sol ou près de celui-ci (moins de 40 cm au-dessus du sol), l’évacuation d’eau devient plus difficile et le linge peut se mouiller.

•Le tuyau doit être inséré dans le conduit d’évacuation à une distance de plus de 15 cm. Si cette distance s’avère trop longue, vous pouvez la faire raccourcir.

•La longueur maximale des tuyaux combinés ne doit pas dépasser 3,2 cm.

15 - FR