WMI 81341 |
Washing Machine |
User's Manual |
Document Number |
2820524011/ 05-05-14.(16:25) |
Please read this user manual first!
Dear Customer,
Thank you for prefering an Beko product. We hope that you get the best results from your product which has been manufactured with high quality and state-of-the-art technology. Therefore, please read this entire user manual and all other accompanying documents carefully before using the product and keep it as a reference for future use. If you handover the product to someone else, give the user manual as well. Follow all warnings and information in the user manual.
Remember that this user manual is also applicable for several other models. Differences between models will be identified in the manual.
Explanation of symbols
Throughout this user manual the following symbols are used:
C Important information or useful hints about usage.
A Warning for hazardous situations with regard to life and property.
B Warning for electric shock.
Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations.
Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities.
This product was manufactured using the latest technology in environmentally friendly conditions.
TABLE OF CONTENTS
1 Important instructions for safety and |
|
environment |
4 |
1.1 General safety . . . . . . . . . . . . . . . . . . . . . . . 4 1.2 Intended use . . . . . . . . . . . . . . . . . . . . . . . . 5 1.3 Children's safety . . . . . . . . . . . . . . . . . . . . . 6 1.4 Package information . . . . . . . . . . . . . . . . . . 6 1.5 Disposing of the waste product . . . . . . . . . . 6 1.6 Compliance with WEEE Directive . . . . . . . . . 7
2 Your washing machine |
8 |
2.1 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.2 Package Contents . . . . . . . . . . . . . . . . . . . . 9 2.3 Technical specifications . . . . . . . . . . . . . . . 10
3 Installation |
11 |
3.1 Appropriate installation location . . . . . . . . . 11 3.2 Removing packaging reinforcement . . . . . . 11 3.3 Removing the transportation locks . . . . . . . 11 3.4 Connecting water supply . . . . . . . . . . . . . . 12 3.5 Connecting to the drain . . . . . . . . . . . . . . . 12 3.6 Adjusting the feet . . . . . . . . . . . . . . . . . . . 13 3.7 Electrical connection . . . . . . . . . . . . . . . . . 13
4 Preparation |
15 |
4.1 Sorting the laundry . . . . . . . . . . . . . . . . . . 15 4.2 Preparing laundry for washing . . . . . . . . . . 16 4.3 Things to be done for energy saving . . . . . . 16 4.4 Initial use . . . . . . . . . . . . . . . . . . . . . . . . . 17 4.5 Correct load capacity . . . . . . . . . . . . . . . . . 17 4.6 Loading the laundry. . . . . . . . . . . . . . . . . . 17 4.7 Using detergent and softener . . . . . . . . . . . 18 4.8 Tips for efficient washing . . . . . . . . . . . . . . 20
5 Operating the product |
21 |
5.1 Control panel. . . . . . . . . . . . . . . . . . . . . . . 21 5.2 Display symbols . . . . . . . . . . . . . . . . . . . . 21 5.3 Preparing the machine . . . . . . . . . . . . . . . .22 5.4 Programme selection. . . . . . . . . . . . . . . . . 22 5.5 Main programmes . . . . . . . . . . . . . . . . . . 22 5.6 Additional programmes . . . . . . . . . . . . . . . 23 5.7 Special programmes . . . . . . . . . . . . . . . . . 24
5.8 Temperature selection . . . . . . . . . . . . . . . . 24 5.9 Spin speed selection . . . . . . . . . . . . . . . . . 24 5.10 Programme and consumption table . . . . . 25 5.11 Auxiliary function selection. . . . . . . . . . . . 27 5.12 Time display . . . . . . . . . . . . . . . . . . . . . . 28 5.13 Starting the programme. . . . . . . . . . . . . . 29 5.14 Progress of programme. . . . . . . . . . . . . . 29 5.15 Loading door lock . . . . . . . . . . . . . . . . . . 29
5.16 Changing the selections after programme has started . . . . . . . . . . . . . . . . . . . . . . . 29
5.17 Child Lock. . . . . . . . . . . . . . . . . . . . . . . . 30 5.18 Cancelling the programme. . . . . . . . . . . . 30 5.19 Machine is in Rinse Hold mode . . . . . . . . 30 5.20 End of programme . . . . . . . . . . . . . . . . . .31
5.21 Your machine is equipped with a “Standby Mode” . . . . . . . . . . . . . . . . . . . . . . . . . . 31
6 Maintenance and cleaning |
32 |
6.1 Cleaning the detergent drawer . . . . . . . . . . 32 6.2 Cleaning the loading door and the drum . . . 32 6.3 Cleaning the body and control panel. . . . . . 33 6.4 Cleaning the water intake filters . . . . . . . . . 33
6.5 Draining remaining water and cleaning the pump filter . . . . . . . . . . . . . . . . . . . . . . . 33
7 |
Troubleshooting |
35 |
|
|
|
8 |
BUILT-IN INSTALLATION |
41 |
|
|
|
3 / EN
1 Important instructions for safety and environment
This section contains safety instructions that will help protect from risk of personal injury or property damage. Failure to follow these instructions shall void any warranty.
1.1 General safety
•This product can be used by children at and above 8 years old and by persons whose physical, sensory or mental capabilities were not fully developed or who lack experience and knowledge provided that they are supervised or trained on the safe usage of the product and the risks it brings out. Children must not play with the product. Cleaning and maintenance works should not be performed by children unless they are supervised by someone.
•Never place the product on a carpet-covered floor. Otherwise, lack of airflow beneath the machine will cause electrical parts to overheat. This will cause problems with your product.
•If the product has a failure, it should not be operated unless it is repaired by the Authorized Service Agent. There is the risk of electric shock!
•This product is designed to resume operating in the event of powering on after a power interruption. If you wish to cancel the programme, see "Cancelling the programme" section.
•Connect the product to a grounded outlet protected by a 13 A fuse. Do not neglect to have the grounding installation made by a qualified electrician. Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations.
•The water supply and draining hoses must be securely fastened and remain undamaged. Otherwise, there is the risk of water leakage.
•Never open the loading door or remove the filter while there is still water in the drum. Otherwise, risk of flooding and injury from hot water will occur.
•Do not force open the locked loading door. The loading door will be ready to open just a few minutes after the washing cycle comes to an end. In case of forcing the loading door to open, the door and the lock mechanism may get damaged.
•Unplug the product when not in use.
•Never wash the product by spreading or pouring water onto it! There is the risk of electric shock!
•Never touch the plug with wet hands! Never unplug by pulling on the cable, always pull out by grabbing the plug.
4 / EN |
Washing Machine /User’s Manual |
|
|
Important instructions for safety and environment
•Use detergents, softeners and supplements suitable for automatic washing machines only.
•Follow the instructions on the textile tags and on the detergent package.
•The product must be unplugged during installation, maintenance, cleaning and repairing procedures.
•Always have the installation and repairing procedures carried out by the Authorized Service Agent. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons.
•If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similary qualified persons in order to avoid a hazard.
•If the power cable is damaged, it must be replaced by the manufacturer, after sales service or a similarly qualified person (preferably an electrician) or someone designated by the importer in order to avoid possible risks.
•Place the product on a rigid, flat and level surface.
•Do not place it on a long-pile rug or similar surfaces.
•Do not place the product on a high platform or near the edge on a cascaded surface.
•Do not place the product on the power cable.
•Never use sponge or scrub materials. These will damage the painted, chrome plated and plastic surfaces.
1.2 Intended use
•This product has been designed for domestic use. It is not suitable for commercial use and it must not be used out of its intended use.
•The product must only be used for washing and rinsing of laundry that are marked accordingly.
•The manufacturer waives any responsibility arisen from incorrect usage or transportation.
•The service life of your product is 10 years. During this period, original spare parts will be available to operate the appliance properly.
Washing Machine /User’s Manual |
5 / EN |
|
|
Important instructions for safety and environment
1.3 Children's safety
•Packaging materials are dangerous to children. Keep packaging materials in a safe place away from reach of the children.
•Electrical products are dangerous for the children. Keep children away from the product when it is in use. Do not let them to tamper with the product. Use child lock to prevent children from intervening with the product.
•Do not forget to close the loading door when leaving the room where the product is located.
•Store all detergents and additives in a safe place away from the reach of the children by closing the cover of the detergent container or sealing the detergent package.
While washing the laundry at high temperatures, the loading door glass becomes hot. Therefore, keep especially the children away from the loading door of the machine while the washing operation is in progress.
1.4 Package information
• Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other
wastes. Take them to the packaging material collection points designated by the local authorities.
1.5 Disposing of the waste product
•This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling. Therefore, do not dispose the product with normal domestic waste at the end of its service life. Take it to a collection point for the recycling of electrical and electronic equipment. Please consult your local authorities to learn the nearest collection point. Help protect the environment and natural resources by recycling used products. For children's safety, cut the power cable and break the locking mechanism of the loading door so that it will be non-functional before disposing of the product.
6 / EN |
Washing Machine /User’s Manual |
|
|
Important instructions for safety and environment
1.6 Compliance with WEEE Directive
This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE).
This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling. Do not dispose of the waste product with normal domestic and other wastes at the end of its service life. Take it to the collection center for the recycling of electrical and electronic equipment. Please consult your local authorities to learn about these collection centers.
Compliance with RoHS Directive:
The product you have purchased complies with EU RoHS Directive (2011/65/ EU). It does not contain harmful and prohibited materials specified in the Directive.
Washing Machine /User’s Manual |
7 / EN |
|
|
2 Your washing machine
2.1 Overview
1 8 
2
3 7 
6
4
5
1- Power cable |
5- Adjustable feet |
2- Top panel |
6- Loading door |
3- Control panel |
7- Detergent drawer |
4- Filter cap |
8- Drain hose |
8 / EN |
Washing Machine /User’s Manual |
|
|
Your washing machine
2.2 Package Contents
3 |
4 |
2 |
|
1 |
|
|
5 |
|
6 |
a |
b |
c |
7
1- Power cable
2- Drain hose
3- Transportation safety bolts *
4- Mains water inlet hose (One of the following filter types is used for the mains hose connection.) a- Electronical water shut-off
b- Mechanical water shut-off c- Standard
5- User Manual
6- Blind plug**
7- Plastic plug group
*Number of transportation safety bolts may change depending on the model of your machine.
**This is supplied if your machine is equipped with double water inlet.
Washing Machine /User’s Manual |
9 / EN |
|
|
Your washing machine
2.3 Technical specifications
Complying Commission Delegated Regulation (EU) No 1061/2010
Supplier name or trademark |
|
Beko |
Model name |
|
WMI81341 |
Rated capacity (kg) |
|
8 |
Energy efficiency class / Scale from A+++ (Highest Efficiency) to D (Lowest Efficiency) |
A+ |
|
Annual Energy Consumption (kWh) (1) |
|
248 |
Energy consumption of the standard 60°C cotton programme at full load (kWh) |
1.389 |
|
Energy consumption of the standard 60°C cotton programme at partial load |
(kWh) |
0.968 |
Energy consumption of the standard 40°C cotton programme at partial load |
(kWh) |
0.784 |
Power consumption in ‘off-mode’ (W) |
|
0.200 |
Power consumption in ‘left-on mode’ (W) |
|
1.000 |
Annual Water Consumption (l) (2) |
|
11000 |
Spin-drying efficiency class / Scale from A (Highest Efficiency) to G (Lowest Efficiency) |
B |
|
Maximum spin speed (rpm) |
|
1300 |
Remaining moisture Content (%) |
|
53 |
Standard cotton programme (3) |
|
Cotton Eco 60°C and 40°C |
Programme time of the standard 60°C cotton programme at full load (min) |
|
178 |
Programme time of the standard 60°C cotton programme at partial load (min) |
149 |
|
Programme time of the standard 40°C cotton programme at partial load (min) |
123 |
|
Duration of the left-on mode (min) |
|
N/A |
Airborne acoustical noise emissions washing/spinning (dB) |
|
50/68 |
Built-in |
|
Yes |
Rated capacity (kg) |
|
8 |
Height (cm) |
|
82 |
Width (cm) |
|
60 |
Depth (cm) |
|
54 |
Net weight (±4 kg.) |
|
71 |
Single Water inlet / Double Water inlet |
|
• / - |
• Available |
|
|
|
|
|
Electrical input (V/Hz) |
|
230 V / 50Hz |
Total current (A) |
|
10 |
Total power (W) |
|
2200 |
Main model code |
|
8811 |
(1)Energy Consumption based on 220 standard washing cycles for cotton programmes at 60°C and 40°C at full and partial load, and the consumption of the low-power modes. Actual energy consumption will depend on how the appliance is used.
(2)Water consumption based on 220 standard washing cycles for cotton programmes at 60°C and 40°C at full and partial load. Actual water consumption will depend on how the appliance is used.
(3)“Standard 60°C cotton programme” and the “standard 40°C cotton programme” are the standard washing programmes to which the information
in the label and the fiche relates and these programmes are suitable to clean normally soiled cotton laundry and that they are the most efficient programmes in terms of combined energy and water consumption.
Technical specifications may be changed without prior notice to improve the quality of the product.
10 / EN |
Washing Machine /User’s Manual |
|
|
3 Installation
Refer to the nearest Authorised Service Agent for installation of the product. To make the product ready for use, review the information in the user manual and make sure that the electricity, tap water supply and water drainage systems are appropriate before calling the Authorised Service Agent. If they are not, call a qualified technician and plumber to have any necessary arrangements carried out.
C Preparation of the location and electrical, tap water and waste water installations at the place of installation is under customer's responsibility.
Make sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or crushed while pushing the product into its place after installation or cleaning procedures.
B warning: Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorised persons.
A warning: Prior to installation, visually check if the product has any defects on it. If so, do not have it installed. Damaged products cause risks for your safety.
3.1 Appropriate installation location
•Place the machine on a rigid floor. Do not place it on a long pile rug or similar surfaces.
•Total weight of the washing machine and the dryer -with full loadwhen they are placed on top of each other reaches to approx. 180
kilograms. Place the product on a solid and flat floor that has sufficient load carrying capacity!
•Do not place the product on the power cable.
•Do not install the product at places where temperature may fall below 0ºC.
•Place the product at least 1 cm away from the edges of other furniture.
3.2 Removing packaging reinforcement
Tilt the machine backwards to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon.
3.3 Removing the transportation locks
A warning: Do not remove the transportation locks before taking out the packaging reinforcement.
warning: Remove the transportation safety bolts before operating the washing machine! Otherwise, the product will be damaged.
1.Loosen all the bolts with a suitable spanner until they rotate freely (C).
2.Remove transportation safety bolts by turning them gently.
3.Attach the plastic covers supplied in the User Manual bag into the holes on the rear panel. (P)
Washing Machine /User’s Manual |
11 / EN |
|
|
Installation
CKeep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future.
Never move the product without the transportation safety bolts properly fixed in place!
3.4 Connecting water supply
CThe water supply pressure required to run the product is between 1 to 10 bars (0.1 – 1 MPa). It is necessary to have 10 – 80 liters of water flowing from the fully open tap in one minute to have your machine run smoothly. Attach a pressure reducing valve if water pressure is higher.
If you are going to use the double water-inlet product as a single (cold) water-inlet unit, you must install the supplied stopper to the hot water valve before operating the product. (Applies for the products supplied with a blind stopper group.)
Awarning: Models with a single water inlet should not be connected to the hot water tap. In such a case the laundry will get damaged or the product will switch to protection mode and will not operate.
warning: Do not use old or used water inlet hoses on the new product. It may cause stains on your laundry.
1.Connect the special hoses supplied with the product to the water inlets on the product. Red hose (left) (max. 90 ºC) is for hot water inlet, blue hose (right) (max. 25 ºC) is for cold water inlet.
Awarning: Ensure that the cold and hot water connections are made correctly when installing the product. Otherwise, your laundry will come out hot at the end of the washing process and wear out.
2.Tighten all hose nuts by hand. Never use a tool when tightening the nuts.
3.Open the taps completely after making the hose connection to check for water leaks at the connection points. If any leaks occur, turn off the tap and remove the nut. Retighten the nut carefully after checking the seal. To prevent water leakages and damages caused by them, keep the taps closed when the machine is not in use.
3.5 Connecting to the drain
•The end of the drain hose must be directly connected to the wastewater drain or to the washbasin.
•Drain hose shall be attached to a wall drain, stand pipe or sink siphon connected to the foul water drain, do not connect to surface water drains.
A warning: Your house will be flooded if the hose comes out of its housing during water discharge. Moreover, there is risk of scalding due to high washing temperatures! To prevent such situations and to ensure smooth water intake and discharge of the machine, fix the end of the discharge hose tightly so that it cannot come out.
•The hose should be attached to a height of at least 40 cm, and 100 cm at most.
•In case the hose is elevated after laying it on the floor level or close to the ground (less than 40 cm above the ground), water discharge becomes more difficult and the laundry may come out excessively wet. Therefore, follow the heights described in the figure.
12 / EN |
Washing Machine /User’s Manual |
Installation
2. Adjust the feet until the product stands level and balanced.
100cm 40cm
•To prevent flowing of dirty water back into the machine and to allow for easy discharge, do not immerse the hose end into the dirty water or do not drive it in the drain more than 15 cm. If it is too long, cut it short.
•The end of the hose should not be bent, it should not be stepped on and the hose must not be pinched between the drain and the machine.
•If the length of the hose is too short, use it by adding an original extension hose. Length of the hose may not be longer than 3.2 m. To avoid water leak failures, the connection between
the extension hose and the drain hose of the product must be fitted well with an appropriate clamp as not to come off and leak.
3.6 Adjusting the feet
A warning: In order to ensure that the product operates more silently and vibrationfree, it must stand level and balanced on its feet. Balance the machine by adjusting the feet. Otherwise, the product may move from its place and cause crushing and vibration problems.
1. Loosen the lock nuts on the feet by hand.
3. Tighten all lock nuts again by hand.
A warning: Do not use any tools to loosen the lock nuts. Otherwise, they will get damaged.
3.7 Electrical connection
Connect the product to a grounded outlet protected by a 13 A fuse. Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations.
•Connection must comply with national regulations.
•Power cable plug must be within easy reach after installation.
•If the current value of the fuse or breaker in the house is less than 13 Amps, have a qualified electrician install a 13 Amp fuse.
•The voltage specified in the "Technical specifications" section must be equal to your mains voltage.
•Do not make connections via extension cables or multi-plugs.
B warning: Damaged power cables must be replaced by the Authorised Service Agents.
Washing Machine /User’s Manual |
13 / EN |
|
|
Installation
Electrical requirements
Before you insert the plug into the wall socket make sure that the voltage and the frequency shown in the rating label corresponds to your electricity supply.
We recommend that this appliance be connected to the mains supply via a suitable switched and fused socket in a readily accessible position. Should the mains lead of the appliance become damaged or need replacing at any time, it must be replaced by a special purpose made mains lead which can only be obtained from a Authorised Service Agent.
B warning: This appliance must be earthed
If the fitted moulded plug is not suitable for your socket, then the plug should be cut off and an appropriate plug fitted.
Destroy the old plug, which is cut off as a plug with a bared cord could cause a shock hazard if inserted into a socket elsewhere in the house. The moulded plug on this appliance incorporates a 13A fuse. Should the fuse need to be replaced an ASTA approved BS1362 fuse of the same rating must be used. Do not forget to refit the fuse cover. In the event of losing the fuse cover, the plug must not be used until a replacement fuse cover has been fitted. Colour of the replacement fuse cover must be the same colour as that visible on the pin face of the plug. Fuse covers are available from any good electrical store.
Important
Fitting a different plug
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals on your plug, proceed as follows:
1Connect the green - yellow or green (earth) wire to the terminal in the plug marked ‘E’ or with the symbol f or coloured green and yellow or green.
2Connect the blue (neutral) wire to the terminal in the plug marked ‘N’ or coloured black.
3Connect the brown (live) wire to the terminal in the plug marked ‘L’ or coloured red.
With the alternative plugs a 13A fuse must be fitted either in the plug or adaptor or in the main fuse box. If in doubt contact a qualified electrician.
Transportation of the product
1. Unplug the product before transporting it.
2. Remove water drain and water supply connections.
3. Drain all water that has remained in the product. See 6.5
4. Install transportation safety bolts in the reverse
order of removal procedure; see 3.3.
C
A warning: Packaging materials are dangerous to children. Keep packaging materials in a safe place away from reach of the children.
14 / EN |
Washing Machine /User’s Manual |
|
|
4 Preparation
4.1 Sorting the laundry
•Sort laundry according to type of fabric, colour, and degree of soiling and allowable water temperature.
•Always obey the instructions given on the garment tags.
|
|
|
|
LAUNDRY WASH SYMBOLS |
|
|
|
|
||||
|
Machine |
Normal wash |
|
|
|
|
|
|
|
|
Not washable |
|
|
Wash |
|
|
|
SensitiveDelicate wash |
|
Hand wash |
|
|
|||
|
Symbols |
|
|
No Iron |
|
|
No Spin |
|||||
|
|
|
|
|
|
|||||||
wASH |
Water |
Maximum |
950C |
700C |
600C |
500C |
400C |
300C |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Temperatures |
Symbol(s) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|||
|
Drying |
Suitable for |
No Iron |
Sensitive / |
Do not dry |
Do not dry |
Do not dry- |
|||||
|
Symbols |
|||||||||||
|
dryer |
|
||||||||||
|
|
|
|
|
Delicate dry |
with dryer |
|
|
clean |
|||
|
|
|
|
|
|
|
|
|||||
DRYiNg |
|
|
|
|
|
|
|
|
|
|
|
|
|
Drying |
At any temperature |
At high temperature |
|
At low temperature |
Without heating |
|
|
|
Hang wet to dry |
Lay in shadow to dry |
Dry-cleanable |
|
Settings |
At medium temperature |
|
Hang to dry |
|
|||||||
|
|
|
Lay to dry |
|||||||||
|
Iron - |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Iron at high |
Iron at medium |
Iron at low |
|
|
|
|||
iRON |
Dry or Steam |
|
|
temperature |
temperature |
temperature |
|
Do not iron |
Iron without steam |
|||
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|||
|
Maximum temperature |
|
200 0C |
150 0C |
|
110 0C |
|
|||||
|
|
|
|
|
|
Bleach (sodium |
Bleach is not |
|
Only bleaches without |
|||
|
All bleaches are allowed |
|
hypochlorite) |
|
||||||||
|
|
allowed |
|
chlorine are allowed |
||||||||
BLEACH |
|
|
|
|
|
can be used |
|
|||||
|
|
|
|
|
|
|
|
|
|
|||
Washing Machine /User’s Manual |
15 / EN |
|
|
Preparation
4.2 Preparing laundry for washing
•Laundry items with metal attachments such as, underwired bras, belt buckles or metal buttons will damage the machine. Remove the metal pieces or wash the clothes by putting them in a laundry bag or pillow case.
•Take out all substances in the pockets such as coins, pens and paper clips, and turn pockets inside out and brush. Such objects may damage the product or cause noise problem.
•Put small size clothes such as infant's socks and nylon stockings in a laundry bag or pillow case.
•Place curtains in without compressing them. Remove curtain attachment items.
•Fasten zippers, sew loose buttons and mend rips and tears.
•Wash “machine washable” or “hand washable” labeled products only with an appropriate programme.
•Do not wash colours and whites together. New, dark coloured cottons release a lot of dye. Wash them separately.
•Tough stains must be treated properly before washing. If unsure, check with a dry cleaner.
•Use only dyes/colour changers and limescale removers suitable for machine wash. Always follow the instructions on the package.
•Wash trousers and delicate laundry turned inside out.
•Keep laundry items made of Angora wool in the freezer for a few hours before washing. This will reduce pilling.
•Laundry that are subjected to materials such as flour, lime dust, milk powder, etc. intensely must be shaken off before placing into the machine.
Such dusts and powders on the laundry may build up on the inner parts of the machine in time and can cause damage.
4.3 Things to be done for energy saving
Following information will help you use the product in an ecological and energy-efficient manner.
•Operate the product in the highest capacity allowed by the programme you have selected, but do not overload; see, "Programme and consumption table".
•Always follow the instructions on the detergent packaging.
•Wash slightly soiled laundry at low temperatures.
•Use faster programmes for small quantities of lightly soiled laundry.
•Do not use prewash and high temperatures for laundry that is not heavily soiled or stained.
•If you plan to dry your laundry in a dryer, select the highest spin speed recommended during washing process.
•Do not use detergent in excess of the amount recommended on the detergent package.
16 / EN |
Washing Machine /User’s Manual |
|
|
Loading...