Washing Machine |
User Manual |
WMI 81442 |
EN ES PT |
Document Number= 2820525130_EN/12-10-15.(11:35) |
1 Important instructions for safety and environment
This section contains safety instructions that will help protect from risk of personal injury or property damage. Failure to follow these instructions shall void any warranty.
1.1General safety
•This product can be used by children at and above 8 years old and by persons whose physical, sensory or mental capabilities were not fully developed or who lack experience and knowledge provided that they are supervised or trained on the safe usage of the product and the risks it brings out. Children must not play with the product. Cleaning and maintenance works should not be performed by children unless they are supervised by someone. Children of less than 3 years should be kept away unless continuously supervised.
•Never place the product on a carpet-covered floor. Otherwise, lack of airflow beneath the machine will cause electrical parts to overheat. This will cause problems with your product.
•If the product has a failure, it should not be operated unless it is repaired by the
Authorized Service Agent. There is the risk of electric shock!
•This product is designed to resume operating in the event of powering on after a power interruption. If you wish to cancel the programme, see "Cancelling the programme" section.
•Connect the product to a grounded outlet protected by a 16 A fuse. Do not neglect to have the grounding installation made by a qualified electrician. Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations.
•The water supply and draining hoses must be securely fastened and remain undamaged. Otherwise, there is the risk of water leakage.
•Never open the loading door or remove the filter while there is still water in the drum. Otherwise, risk of flooding and injury from hot water will occur.
•Do not force open the locked loading door.The loading door will be ready to open just a few minutes after the washing cycle comes to an end. In case of forcing the loading door to open, the door and the lock mechanism may get damaged.
•Unplug the product when not in use.
•Never wash the product by spreading or pouring water onto it! There is the risk of electric shock!
•Never touch the plug with wet hands! Never unplug by pulling on the cable, always pull out by grabbing the plug.
•Use detergents, softeners and supplements suitable for automatic washing machines only.
This product was manufactured using the latest technology in environmentally friendly conditions.
2 / 68 EN |
Washing Machine / User’s Manual |
|
|
•Follow the instructions on the textile tags and on the detergent package.
•The product must be unplugged during installation, maintenance, cleaning and repairing procedures.
•Always have the installation and repairing procedures carried out by the Authorized Service Agent. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons.
•If the power cable is damaged, it must be replaced by the manufacturer, after sales service or a similarly qualified person (preferably an electrician) or someone designated by the importer in order to avoid possible risks.
•Place the product on a rigid, flat and level surface.
•Do not place it on a long-pile rug or similar surfaces.
•Do not place the product on a high platform or near the edge on a cascaded surface.
•Do not place the product on the power cable.
•Never use sponge or scrub materials. These will damage the painted, chrome plated and plastic surfaces.
1.2Intended use
•This product has been designed for domestic use. It is not suitable for commercial use and it must not be used out of its intended use.
•The product must only be used for washing and rinsing of laundry that are marked accordingly.
•The manufacturer waives any responsibility arisen from incorrect usage or transportation.
1.3Children's safety
•Packaging materials are dangerous to children. Keep packaging materials in a safe place away from reach of the children.
•Electrical products are dangerous for the children. Keep children away from the product when it is in use. Do not let them to tamper with the product. Use child lock to prevent children from intervening with the product.
•Do not forget to close the loading door when leaving the room where the product is located.
•Store all detergents and additives in a safe place away from the reach of the children by closing the cover of the detergent container or sealing the detergent package.
While washing the laundry at high temperatures, the loading door glass becomes hot. Therefore, keep especially the children away from the loading door of the machine while the washing operation is in progress.
3 / 68 EN |
Washing Machine / User’s Manual |
|
|
1.4Package information
•Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities.
1.5Disposing of the waste product
•This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling. Therefore, do not dispose the product with normal domestic waste at the end of its service life. Take it to a collection point for the recycling of electrical and electronic equipment. Please consult your local authorities to learn the nearest collection point. Help protect the environment and natural resources by recycling used products. For children's safety, cut the power cable and break the locking mechanism of the loading door so that it will be non-functional before disposing of the product.
1.6Compliance with WEEE Directive
This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE).
This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling. Do not dispose of the waste product with normal domestic and other wastes at the end of its service life. Take it to the collection center for the recycling of electrical and electronic equipment. Please consult your local authorities to learn about these collection centers.
Compliance with RoHS Directive:
The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain harmful and prohibited materials specified in the Directive.
4 / 68 EN |
Washing Machine / User’s Manual |
|
|
2 Installation
Refer to the nearest Authorised Service Agent for installation of the product. To make the product ready for use, review the information in the user manual and make sure that the electricity, tap water supply and water drainage systems are appropriate before calling the Authorized Service Agent. If they are not, call a qualified technician and plumber to have anyCnecessary arrangements carried out.
B
A
2.1 Appropriate installation location
•Place the machine on a rigid floor. Do not place it on a long pile rug or similar surfaces.
•Total weight of the washing machine and the dryer -with full loadwhen they are placed on top of each other reaches to approx. 180 kilograms. Place the product on a solid and flat floor that has sufficient load carrying capacity!
•Do not place the product on the power cable.
•Do not install the product at places where temperature may fall below 0ºC.
•Place the product at least 1 cm away from the edges of other furniture.
2.2 Removing packaging reinforcement
Tilt the machine backwards to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon.
2.3 Removing the transportation locks
Awarning: Do not remove the transportation locks before taking out the packaging reinforcement.
warning: Remove the transportation safety bolts before operating the washing machine! Otherwise, the product will be damaged.
1.Loosen all the bolts with a suitable spanner until they rotate freely (C).
2.Remove transportation safety bolts by turning them gently.
3.Attach the plastic covers supplied in the User Manual bag into the holes on the rear panel. (P)
C Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future.
Never move the product without the transportation safety bolts properly fixed in place!
2.4 Connecting water supply
C The water supply pressure required to run the product is between 1 to 10 bars (0.1 – 1 MPa). It is necessary to have 10 – 80 liters of water flowing from the fully open tap in one minute to have your machine run smoothly.
Attach a pressure reducing valve if water pressure is higher.
If you are going to use the double water-inlet product as a single (cold) water-inlet unit, you must install the supplied stopper to the hot water valve before operating the product. (Applies for the products supplied with a blind stopper group.)
A warning: Models with a single water inlet should not be connected to the hot water tap. In such a case the laundry will get damaged or the product will switch to protection mode and will not operate.
warning: Do not use old or used water inlet hoses on the new product. It may cause stains on your laundry.
1.Connect the special hoses supplied with the product to the water inlets on the product. Red hose (left) (max. 90 ºC) is for hot water inlet, blue hose (right) (max. 25 ºC) is for cold water inlet.
Awarning: Ensure that the cold and hot water connections are made correctly when installing the product.
Otherwise, your laundry will come out hot at the end of the washing process and wear out.
5 / 68 EN |
Washing Machine / User’s Manual |
2.Tighten all hose nuts by hand. Never use a tool when tightening the nuts.
3.Open the taps completely after making the hose connection to check for water leaks at the connection points. If any leaks occur, turn off the tap and remove the nut. Retighten the nut carefully after checking the seal. To prevent water leakages and damages caused by them, keep the taps closed when the machine is not in use.
2.5 Connecting to the drain
•The end of the drain hose must be directly connected to the wastewater drain or to the washbasin.
Awarning: Your house will be flooded if the hose comes out of its housing during water discharge. Moreover, there is risk of scalding due to high washing temperatures!
To prevent such situations and to ensure smooth water intake and discharge of the machine, fix the end of the discharge hose tightly so that it cannot come out.
•The hose should be attached to a height of at least 40 cm, and 100 cm at most.
•In case the hose is elevated after laying it on the floor level or close to the ground (less than 40 cm above the ground), water discharge becomes more difficult and the laundry may come out excessively wet. Therefore, follow the heights described in the figure.
100cm 40cm
•To prevent flowing of dirty water back into the machine and to allow for easy discharge, do not immerse the hose end into the dirty water or do not drive it in the drain more than 15 cm. If it is too long, cut it short.
•The end of the hose should not be bent, it should not be stepped on and the hose must not be pinched between the drain and the machine.
•If the length of the hose is too short, use it by adding an original extension hose. Length of the hose may not be longer than 3.2 m.To avoid water leak failures, the connection between the extension hose and the drain hose of the product must be fitted well with an appropriate clamp as not to come off and leak.
2.6 Adjusting the feet
Awarning: In order to ensure that the product operates more silently and vibration-free, it must stand level and balanced on its feet. Balance the machine by adjusting the feet. Otherwise, the product may move from its place and cause crushing and vibration problems.
1.Loosen the lock nuts on the feet by hand.
2.Adjust the feet until the product stands level and balanced.
3.Tighten all lock nuts again by hand.
Awarning: Do not use any tools to loosen the lock nuts. Otherwise, they will get damaged.
2.7 Electrical connection
Connect the product to a grounded outlet protected by a 16 A fuse. Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations.
•Connection must comply with national regulations.
•Power cable plug must be within easy reach after installation.
•If the current value of the fuse or breaker in the house is less than 16 Amps, have a qualified electrician install a 16 Amp fuse.
•The voltage specified in the "Technical specifications" section must be equal to your mains voltage.
•Do not make connections via extension cables or multiplugs.
Bwarning: Damaged power cables must be replaced by the Authorized Service Agents.
Transportation of the product
1.Unplug the product before transporting it.
2.Remove water drain and water supply connections.
3.Drain all water that has remained in the product. (SEE 5.5)
4.Install transportation safety bolts in the reverse order of removal procedure; (SEE 2.3)
C Never move the product without the transportation safety bolts properly fixed in place!
Awarning: Packaging materials are dangerous to children. Keep packaging materials in a safe place away from reach of the children.
6 / 68 EN |
Washing Machine / User’s Manual |
|
|
3 Preparation
3.1 Sorting the laundry
•Sort laundry according to type of fabric, colour, and degree of soiling and allowable water temperature.
•Always obey the instructions given on the garment tags.
3.2 Preparing laundry for washing
•Laundry items with metal attachments such as, underwired bras, belt buckles or metal buttons will damage the machine. Remove the metal pieces or wash the clothes by putting them in a laundry bag or pillow case.
•Take out all substances in the pockets such as coins, pens and paper clips, and turn pockets inside out and brush. Such objects may damage the product or cause noise problem.
•Put small size clothes such as infant's socks and nylon stockings in a laundry bag or pillow case.
•Place curtains in without compressing them. Remove curtain attachment items.
•Fasten zippers, sew loose buttons and mend rips and tears.
•Wash “machine washable” or “hand washable” labeled products only with an appropriate programme.
•Do not wash colours and whites together. New, dark coloured cottons release a lot of dye. Wash them separately.
•Tough stains must be treated properly before washing. If unsure, check with a dry cleaner.
•Use only dyes/colour changers and limescale removers suitable for machine wash.Always follow the instructions on the package.
•Wash trousers and delicate laundry turned inside out.
•Keep laundry items made of Angora wool in the freezer for a few hours before washing.This will reduce pilling.
•Laundry that are subjected to materials such as flour, lime dust, milk powder, etc. intensely must be shaken off before placing into the machine. Such dusts and powders on the laundry may build up on the inner parts of the machine in time and can cause damage.
3.3 Things to be done for energy saving
Following information will help you use the product in an ecological and energy-efficient manner.
•Operate the product in the highest capacity allowed by the programme you have selected, but do not overload; see, "Programme and consumption table".
•Always follow the instructions on the detergent packaging.
•Wash slightly soiled laundry at low temperatures.
•Use faster programmes for small quantities of lightly soiled laundry.
•Do not use prewash and high temperatures for laundry that is not heavily soiled or stained.
•If you plan to dry your laundry in a dryer, select the highest spin speed recommended during washing process.
•Do not use detergent in excess of the amount recommended on the detergent package.
3.4 Initial use
Before starting to use the product, make sure that all preparations are made in accordance with the instructions in sections “Important safety instructions” and “Installation”.
To prepare the product for washing laundry, perform first operation in Drum Cleaning programme. If your product is not equipped with Drum Cleaning programme, perform the Initial Use procedure in accordance with the methods described under “5.2 Cleaning the loading door and the drum” section of the user manual.
C Use an anti-limescale suitable for the washing machines.
C Some water might have remained in the product due to the quality control processes in the production. It is not harmful for the product.
3.5 Correct load capacity
The maximum load capacity depends on the type of laundry, the degree of soiling and the washing programme desired. The machine automatically adjusts the amount of water according to the weight of the loaded laundry.
Awarning: Follow the information in the “Programme and consumption table”.When overloaded, machine's washing performance will drop. Moreover, noise and vibration problems may occur.
Laundry type |
Weight (g) |
Bathrobe |
1200 |
Napkin |
100 |
Duvet cover |
700 |
Bed Sheet |
500 |
Pillowcase |
200 |
Tablecloth |
250 |
Towel |
200 |
Hand towel |
100 |
Evening gown |
200 |
Underclothing |
100 |
Men’s overalls |
600 |
Men’s shirt |
200 |
Men’s pajamas |
500 |
Blouses |
100 |
3.6 Loading the laundry
1.Open the loading door.
2.Place laundry items loosely into the machine.
3.Push the loading door to close until you hear a locking sound. Ensure that no items are caught in the door.
7 / 68 EN |
Washing Machine / User’s Manual |
|
|
C The loading door is locked while a programme is running.
The door can only be opened a while after the programme comes to an end.
Awarning: In case of misplacing the laundry, noise and vibration problems may occur in the machine.
3.7 Using detergent and softener
C When using detergent, softener, starch, fabric dye, bleach or limescale remover read the manufacturer's instructions on the package carefully and follow the suggested dosage values. Use measuring cup if available.
Detergent Drawer
Detergent drawer of your washing machine consists of four different compartments for powder main wash detergent, liquid main wash detergent, liquid softener and powder pre-wash detergent. Each of these laundry additives are dispensed automatically in the relevant time during the washing Programme.
Do not place the laundry additives directly into the drum.
Always use the detergent drawer.
Do not close the drawer too fast after putting the laundry additives.This may cause the additives be dispensed early, creating unsatisfactory washing results and fabric damage.
C Do not open the drawer during washing Programme.
The detergent drawer compartments are indicated below:
1)Left compartment with number “II” (Main wash compartment for powder detergent or powder bleach/ stain remover)
2)Left compartment with number “II 
” (Main wash compartment for liquid detergent or liquid stain remover)
3)Middle compartment with number “I” (pre-wash compartment for powder detergent, powder stain remover or liquid bleach - liquid bleach must be added either during the pre-wash or during the first rinsing step of
the washing Programme). Liquid bleach must be added manually while the machine takes in water.
4)Right compartment with “
” symbol (liquid softener compartment)
2
1
3 4
(II) Main Wash Compartment
Before starting the washing Programme, put powder detergent into the left compartment with number “II”. Use the detergent manufacturer’s measuring cup and follow the instructions on the package. Powder bleach/stain remover must also be put into this compartment.
Put the liquid detergent into the main wash compartment with number “II 
” before starting the washing Programme. Liquid stain remover must be put into this compartment. Put the suggested amount of liquid detergent into the
left compartment with “II 
” symbol and dilute it to the maximum filling level line (max. II 
) with warm water. Particularly the concentrated detergents must be diluted with warm water; otherwise, the siphon may get clogged in time.
Do not fill the detergent above the maximum filling level line; otherwise the excess amount of detergent will reach the laundry without water and may cause stains on the garments.In this case you will need to refill the compartment. Do not pour the detergent onto the laundry
directly since this may cause stains on the garments.
Liquid Softener Compartment
Put the suggested amount of liquid softener into the right compartment with “
” symbol and dilute it to the maximum filling level line (max. 
) with warm water.
Particularly the concentrated softeners must be diluted with warm water; otherwise, the siphon may get clogged in time.
Do not fill the softener above the maximum filling level line; otherwise the excess amount of softener will get mixed with the washing water and you will need to refill the compartment. Do not pour the softener onto the laundry directly since this may cause stains on the garments.
Liquid softener will be dispensed automatically at the final
rinsing step of the washing Programme.
(I) Pre-Wash Compartment
Put the powder pre-wash detergent or powder stain remover into the middle compartment with number “I”.
You can also put liquid bleach into this compartment while the machine takes in water during pre-wash or first rinsing step.Adding the liquid bleach while the machine takes in water allows it to be diluted before it is poured onto the laundry.
You must select extra rinsing option if you use liquid bleach in a washing Programme. Bleach must be removed from the laundry with rinsing; otherwise it may cause itching on the skin.
C Read the dosage instructions and label of your garments carefully before using the liquid bleach.
Starch
•Add liquid starch, powder starch or the dyestuff into the softener compartment as instructed on the package.
•Never use fabric softener and starch together in the same washing cycle.
•Wipe the inside of the drum after using starch.
8 / 68 EN |
Washing Machine / User’s Manual |
|
|
Bleaches
If you are going to use regular bleach in your machine, it is suggested to select a Programme with pre-wash step and add the bleach at the beginning of the pre-wash without putting detergent into the pre-wash compartment.
Alternatively, it is suggested to select a Programme with extra rinsing and add the bleach while the machine takes in water from the detergent drawer in the first rinsing step.
Bleach should not be mixed with detergent. Since the bleach may cause irritation on skin, little amounts must be used and rinsed thoroughly. Do not pour bleach directly onto the laundry and do not use it with colour laundry.
When using oxygen based bleach, follow the instructions on the package and select a Programme at low temperature. Oxygen based bleach can be used together with the detergent. However, if it is not at the same thickness with the detergent, then it must be added from the compartment number “II” right after the detergent foams with water.
Eliminating lime formation
•When required, use only appropriate lime removers developed specifically for washing machines and always follow the instructions on the package.
3.8 Tips for efficient washing
Soiling Level
|
|
Clothes |
|
|
|
|
Light colours and whites |
Colours |
Dark colours |
Delicates/ |
|
|
Woolens/Silks |
||||
|
|
|
|
||
|
(Recommended temperature |
(Recommended temperature |
(Recommended |
(Recommended |
|
|
temperature range |
temperature range |
|||
|
range based on soiling level: |
range based on soiling level: |
based on soiling level: |
based on soiling level: |
|
|
40-90ºC) |
cold-40ºC) |
cold-40ºC) |
cold-30ºC) |
|
|
|
|
|||
|
It may be necessary to pre- |
Powder and liquid |
|
|
|
|
|
|
|||
|
treat the stains or perform |
|
|
||
|
detergents recommended |
|
|
||
|
prewash. Powder and liquid |
|
Prefer liquid |
||
|
for colours can be used at |
Liquid detergents |
|||
Heavily Soiled |
detergents recommended |
detergents produced |
|||
dosages recommended for |
suitable for colours |
||||
|
for whites can be used at |
for delicate clothes. |
|||
|
heavily soiled clothes. It is |
and dark colours can |
|||
(difficult stains such |
dosages recommended for |
Woolen and silk |
|||
recommended to use powder |
be used at dosages |
||||
as grass, coffee, |
heavily soiled clothes. It is |
detergents to clean clay and |
recommended for |
clothes must be |
|
recommended to use powder |
washed with special |
||||
fruits and blood.) |
soil stains and the stains that |
heavily soiled clothes. |
|||
detergents to clean clay and |
woolen detergents. |
||||
|
are sensitive to bleaches. Use |
|
|||
|
soil stains and the stains that |
|
|
||
|
are sensitive to bleaches. |
detergents without bleach. |
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
Powder and liquid detergents |
Liquid detergents |
Prefer liquid |
|
Normally Soiled |
Powder and liquid detergents |
detergents produced |
|||
|
recommended for whites |
recommended for colours |
suitable for colours |
for delicate clothes. |
|
|
can be used at dosages |
and dark colours can |
|||
(For example, stains |
can be used at dosages |
Woolen and silk |
|||
recommended for normally |
be used at dosages |
||||
caused by body on |
recommended for normally |
soiled clothes. Use detergents |
recommended for |
clothes must be |
|
collars and cuffs) |
soiled clothes. |
without bleach. |
normally soiled clothes. |
washed with special |
|
|
woolen detergents. |
||||
|
|
|
|
||
|
|
|
|
|
|
|
|
Powder and liquid detergents |
Liquid detergents |
Prefer liquid |
|
Lightly Soiled |
Powder and liquid detergents |
detergents produced |
|||
recommended for colours |
suitable for colours |
||||
|
recommended for whites |
can be used at dosages |
and dark colours can |
for delicate clothes. |
|
|
can be used at dosages |
Woolen and silk |
|||
(No visible stains |
recommended for lightly |
be used at dosages |
|||
recommended for lightly soiled |
clothes must be |
||||
soiled clothes. Use detergents |
recommended for lightly |
||||
exist.) |
clothes. |
washed with special |
|||
|
|
without bleach. |
soiled clothes. |
woolen detergents. |
|
|
|
|
|
||
|
|
|
|
|
9 / 68 EN |
Washing Machine / User’s Manual |
|
|
4 Operating the product
4.1 Control panel
1 |
|
2 |
|
3 |
4 |
5 |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
6 |
|
7 |
|
8 |
|
|
|
|
|
1 |
- Spin Speed Adjustment button |
|
5 |
- On / Off button |
|
|
||||
2 |
- Display |
|
|
|
|
6 |
- Delayed Start buttons (+ / -) |
|
|
|
3 |
- Temperature Adjustment button |
|
7 |
- Auxiliary Function buttons |
|
|
||||
4 |
- Programme Selection knob |
|
8 |
- Start / Pause / Cancel button |
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Indicative values for Synthetics programmes (EN) |
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
(kg)Load |
Water Consumption(l) |
|
Energy Consumption (kWh) |
Programme Duration(min) * |
Remaining Moisture Content |
Remaining Moisture Content |
|
|
|
|
|
≤ 1000 rpm |
> 1000 rpm |
|
|||||
|
|
|
|
|
|
|
|
(%) ** |
(%) ** |
|
|
|
|
|
|
|
|
|
|
|
|
|
Synthetics 60 |
3 |
45 |
|
1.00 |
90 / 120 |
45 |
40 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Synthetics 40 |
3 |
45 |
|
0.45 |
70 / 100 |
45 |
40 |
|
|
|
|
|
|
|
|
|
|
|
||
|
* You can see the washing time of the programme you have selected on the display of the machine. It is normal that small differences may occur |
|
||||||||
|
between the time shown on the display and the real washing time. |
|
|
|
|
|
||||
|
|
|
|
|
||||||
|
** Remaining moisture content values may differ according to the selected spin speed. |
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
Dark wash Dark wash (Darkcare) (Darkcare)
Synthetics
Cottons Pre-wash |
Main |
|
wash |
Rinse |
Wash |
Spin |
Delicate Pet hair Door Ready |
|
|
|
removal |
Drain |
Anti- |
Duvet |
Child- |
Hand |
BabyProtect |
Cotton |
Woollens expres 14 |
Daily |
mini 30 |
On/Off |
|
|
|
|
|
|
|
|
|
|
|
(Pump) |
creasing |
(Bedding) proof lock |
Wash |
|
Eco |
Super short |
|
|
|
|
|
|
|
|
|
|
|
express |
|
|
|
Daily |
Rinse hold |
Start/ |
No spin |
Quick |
Finished |
Cold |
Temperature Self |
Lingerie |
Eco Clean BabyProtect + |
|
express |
|
Pause |
|
wash |
|
|
Clean |
|
|
|
Mixed 40 |
Super 40 |
Extra rinse |
Freshen |
Shirts |
Jeans |
Sport |
Time delay Intensive |
Fasihon |
Anti- |
PHR + |
(Mix40) |
|
(Rinse Plus) up |
|
|
|
|
care |
allergic |
|
|
10 / 68 EN |
Washing Machine / User’s Manual |
|
|
4.2 Display symbols
F1 |
F2 |
F3 |
F4 |
a - Spin Speed indicator b - Temperature indicator c - Spin symbol
d - Temperature symbol
e - Remaining Time and Delayed Start indicator
f - Programme Indicator symbols (Prewash / Main Wash / Rinse / Softener / Spin)
g - Economy symbol
h - Delayed Start symbol i - Door Locked symbol j - Start symbol
k - Pause symbol
l - Auxiliary Function symbols m - No Water symbol
4.3 Preparing the machine
Make sure that the hoses are connected tightly. Plug in your machine. Turn the tap on completely. Place the laundry in the machine. Add detergent and fabric softener.
4.4 Programme selection
Select the programme suitable for the type, quantity and soiling degree of the laundry in accordance with the
"Programme and consumption table" and the temperature table below.
90˚C |
Heavily soiled white cottons and linens. (coffee table |
|
covers, tableclothes, towels, bed sheets, etc.) |
||
|
Normally soiled, coloured, fade proof linens, cottons or
60˚C synthetic clothes (shirt, nightgown, pajamas, etc.) and lightly soiled white linens (underwear, etc.)
40˚C- |
Blended laundry including delicate textile (veil curtains, |
30˚C- Cold |
etc.), synthetics and woolens. |
Select the desired programme with the Programme
Selection button.
C
4.5 Main programmes
Depending on the type of fabric, use the following main
programmes.
• Cottons
Use this programme for your cotton laundry (such as bed sheets, duvet and pillowcase sets, towels, bathrobes, underwear, etc.).Your laundry will be washed with vigorous
washing action for a longer washing cycle.
• Synthetics
Use this programme to wash your synthetic clothes (shirts, blouses, synthetic/cotton blends, etc.). It washes with a gentle action and has a shorter washing cycle compared to the Cottons programme.
For curtains and tulle, use the Synthetic 40˚C programme with prewash and anti-creasing functions selected. As their meshed texture causes excessive foaming, wash the veils/ tulle by putting little amount of detergent into the main wash compartment. Do not put detergent in the prewash
compartment.
• Woollens
Use this programme to wash your woolen clothes. Select the appropriate temperature complying with the tags of your clothes. Use appropriate detergents for woolens.
4.6 Additional programmes
For special cases, additional programmes are available in
the machine.
C
• Cotton Economic
You may wash your normally soiled durable cotton and linen laundry in this programme with the highest energy and water saving compared to all other wash programmes suitable for cottons.Actual water temperature may differ from the declared cycle temperature. Programme duration may automatically be shortened during later stages of the programme if you wash less amount (e.g. ½ capacity or less) of laundry. In this case energy and water consumption will be further decreased giving you the opportunity for a more economical wash.This feature is available for certain
models having remaining time display.
• BabyProtect
Use this programme to wash baby laundry, and the laundry that belongs to allergic persons. Longer heating time and an
additional rinsing step provide a higher level of hygiene.
• Hand wash
Use this programme to wash your woolen/delicate clothes that bear “not machinewashable” tags and for which hand wash is recommended. It washes laundry with a very gentle washing action to not to damage clothes.
• Daily Express
Use this programme to wash your lightly soiled cotton
clothes in a short time.
• Super Short Express
Use this programme to wash your little amount of lightly soiled cotton clothes in a short time.
11 / 68 EN |
Washing Machine / User’s Manual |
|
|
4.8 Temperature selection
Whenever a new programme is selected, the maximum temperature for the selected programme appears on the temperature indicator.
To decrease the temperature, press the Temperature
Adjustment button.Temperature decreases with increments of 10° and finally,“-” symbol indicating the cold wash option
appears on the display.
C
Economy symbol
Indicates the programmes and temperatures that provide
energy savings.
C
4.9 Spin speed selection
Whenever a new programme is selected, the recommended spin speed of the selected programme is displayed on the spin speed indicator.
To decrease the spin speed, press the Spin Speed
Adjustment button. Spin speed decreases gradually.Then, depending on the model of the product, "Rinse Hold" and "No Spin" options appear on the display. See "Auxiliary function selection" section for explanations of these options.
C Rinse Hold option is indicated with “
” symbol and No Spin option is indicated with “ ” symbol.
Rinse Hold
If you are not going to unload your clothes immediately after the programme completes, you may use rinse hold function to keep your laundry in the final rinsing water in order to prevent them from getting wrinkled when there is no water in the machine. Press Start / Pause /Cancel button after this process if you want to drain the water without spinning your laundry. Programme will resume and complete after draining the water.
If you want to spin the laundry held in water, adjust the Spin Speed and press Start / Pause / Cancel button.
The programme resumes. Water is drained, laundry is spun and the programme is completed.
Washing Machine / User’s Manual
4.10 Programme and consumption table
EN |
|
2 |
|
|
|
|
Programme (°C) |
|
|
(kg)LoadMax. |
ConsumptionWater(l) |
ConsumptionEnergy(kWh) |
Speed***Max. |
|
|
|
|
|
|
|
|
|
|
8 |
74 |
2,40 |
1400 |
|
90 |
|
||||
Cottons |
60 |
|
8 |
72 |
1,70 |
1400 |
|
40 |
|
8 |
72 |
0,95 |
1400 |
BabyProtect |
90 |
|
8 |
100 |
2,25 |
1400 |
|
60** |
|
8 |
58 |
1,07 |
1400 |
Cotton Economic |
60** |
|
4 |
44 |
0,70 |
1400 |
40** |
|
4 |
44 |
0,68 |
1400 |
|
|
|
|||||
|
40 |
|
8 |
72 |
0,77 |
1400 |
Intensive |
60 |
|
8 |
72 |
1,60 |
1400 |
Synthetics |
60 |
|
3 |
45 |
1,00 |
1200 |
40 |
|
3 |
45 |
0,45 |
1200 |
|
|
|
|||||
Eco Clean |
20 |
|
3,5 |
39 |
0,16 |
1400 |
Mix 40 |
40 |
|
3,5 |
45 |
0,55 |
1200 |
Super short express |
30 |
|
2 |
35 |
0,10 |
1400 |
|
90 |
|
8 |
55 |
1,95 |
1400 |
Daily express |
60 |
|
8 |
55 |
1,10 |
1400 |
|
30 |
|
8 |
65 |
0,22 |
1400 |
Woollens |
40 |
|
1,5 |
45 |
0,30 |
1200 |
Hand wash |
30 |
|
1 |
35 |
0,20 |
1200 |
Darkcare |
40 |
|
3 |
82 |
0,55 |
1200 |
Self Clean |
70 |
|
- |
95 |
2,15 |
800 |
Freshen Up |
- |
|
2 |
30 |
0,03 |
1200 |
|
|
|
|
|
|
|
Auxiliary functions
|
|
|
|
Selectable temperature range |
|
|
|
Anti-Creasing |
°C |
Prewash |
Quick Wash |
Rinse Plus |
|
|
• |
• |
• |
• |
90-Cold |
• |
• |
• |
• |
90-Cold |
• |
• |
• |
• |
90-Cold |
|
|
* |
|
90-30 |
|
|
|
|
60-Cold |
|
|
|
|
60-Cold |
|
|
|
|
60-Cold |
|
|
|
|
60-Cold |
|
|
* |
• |
60-40 |
• |
• |
• |
• |
60-Cold |
• |
• |
• |
• |
60-Cold |
|
|
|
|
20 |
• |
• |
• |
• |
40-Cold |
|
|
• |
|
30-Cold |
|
|
• |
|
90-Cold |
|
|
• |
|
90-Cold |
|
|
• |
|
90-Cold |
|
|
• |
|
40-Cold |
|
|
|
|
30-Cold |
|
|
* |
|
40-Cold |
|
|
* |
|
70 |
|
|
|
|
- |
|
|
|
|
|
• : Selectable
* :Automatically selected, no cancelling.
**: Energy Label programme (EN 60456 Ed.3)
***If maximum spin speed of the machine is lower then this value, you can only select up to the maximum spin speed.
-: See the programme description for maximum load.
**“Cotton eco 40°C and Cotton eco 60°C are standard cycles.”These cycles are known as ‘40°C cotton standard cycle’ and ‘60°C cotton standard cycle’ and indicated with the 
symbols on the panel.
C The auxiliary functions in the table may vary according to the model of your machine.
Water and power consumption may vary subject to the changes in water pressure, water hardness and temperature, ambient temperature, type and amount of laundry, selection of auxiliary functions and spin speed, and changes in electric voltage.
You can see the washing time of the programme you have selected on the display of the machine. It is normal that small differences may occur between the time shown on the display and the real washing time.
“Selectability of auxiliary functions might be changed by the manufacturer. New selectabilities might be added or existing ones might be removed.”
“The spin speed of your machine may vary among the programmes, however this speed cannot exceed the max. spin speed of your machine.”
13 / 68 EN |
Washing Machine / User’s Manual |
|
|
4.12 Time display
Remaining time to complete the programme appears on the display while the programme is running. Tim is displayed as
“01:30” in hours and minutes format.
C
Delayed start
With the Delayed Start function the startup of the programme may be delayed up to 24 hours. Delayed start timeCcan be increased by increments of 30 minutes.
Open the loading door, place the laundry and put detergent, etc. Select the washing programme, temperature, spin speed and, if required, the auxiliary functions. Set the desired delayed start time by pressing the Delayed Start + or - buttons. Delayed Start symbol flashes. Press Start / Pause / Cancel button. Delayed start countdown starts. Delayed Start symbol illuminates steadily. Start symbol appears.“:” sign in the middle of the delayed start time on the display
starts flashing.
C
Changing the delayed start period
If you want to change the time during countdown:
Press Start / Pause / Cancel button.“:” sign in the middle of the delayed start time on the display stops flashing. Pause symbol appears. Delayed Start symbol flashes. Start symbol disappears. Set the desired delayed start time by pressing the Delayed Start + or - buttons. Press Start / Pause / Cancel button. Delayed Start symbol illuminates steadily. Pause symbol disappears. Start symbol appears.“:” sign in the middle of the delayed start time on the display starts flashing.
Cancelling the Delayed Start function
If you want to cancel the delayed start countdown and start the programme immediately:
Press Start / Pause / Cancel button.“:” sign in the middle of the delayed start time on the display stops flashing. Start symbol disappears. Pause symbol and Delayed Start symbol flashes. Decrease the delayed start time by pressing the Delayed Start - button. Programme duration appears after 30 minutes. Press Start / Pause / Cancel button to start the programme.
Washing Machine / User’s Manual
4.13 Starting the programme
Press Start / Pause / Cancel button to start the programme. Start symbol showing the startup of the programme will turn on. Loading door is locked and Door Locked symbol appears on the display.The symbol of the step from which the programme has started appears on the display (Prewash, Main Wash, Rinse, Softener and Spin).
4.14 Progress of programme
Progress of a running programme is indicated on the display with a set of symbols.
Relevant symbol appears on the display at the beginning of each programme step and all symbols remain lit at the end of the programme.The farthermost right symbol indicates
the current programme step.
Prewash
If the Prewash auxiliary function is selected, Prewash symbol appears on the display indicating that the prewash step has
started.
Main Wash
Main Wash symbol indicating that the main wash step has
started appears on the display.
Rinse
Rinse symbol indicating that the rinsing step has started
appears on the display.
Softener
Softener symbol indicating that the softener step has started
appears on the display.
Spin
Appears at the beginning of the final spin step and remains
lit during Spin and Pump special programmes.
C
4.15 Loading door lock
There is a locking system on the loading door of the machine that prevents opening of the door in cases when the water level is unsuitable.
Door Locked symbol appears when the loading door is locked.This symbol will flash until the loading door becomes ready to open when programme completes or the machine is paused. Do not force to open the loading door in this step. Symbol disappears when the door is ready to open.You can open the door when the symbol disappears.
4.16 Changing the selections after programme has started
Switching the machine to pause mode
Press the Start / Pause / Cancel button to switch the machine to pause mode. Pause symbol appears on the display indicating that the machine is paused. Start symbol disappears.
Changing the speed and temperature settings for auxiliary functions
Depending on the step the programme has reached, you may cancel or activate the auxiliary functions; see, "Auxiliary function selection".
You may also change the speed and temperature settings; see, "Spin speed selection" and "Temperature selection".
Adding or taking out laundry
Press the Start / Pause / Cancel button to switch the machine to pause mode. The programme follow-up light of the relevant step during which the machine was switched into the pause mode will flash.Wait until the Loading Door can be opened. Open the Loading Door and add or take out the laundry. Close the Loading Door. Make changes in auxiliary functions, temperature and speed settings if necessary. Press Start / Pause / Cancel button to start the
machine.
C
4.17 Child Lock
Use Child Lock function to prevent children from tampering with the machine. Thus you can avoid any changes in a
running programme.
C
To activate the Child Lock:
Press and hold 2nd and 4th Auxiliary Function buttons for 3 seconds.“Con” appears on the display.
C Same phrase will appear on the display if you press any button when Child Lock is enabled.
15 / 68 EN
4.19 Machine is in Rinse Hold mode
Spin symbol flashes and Pause symbol illuminates when the machine is in Rinse Hold mode.
If you want to spin your laundry when the machine is in this mode:
Adjust the spin speed and press Start / Pause / Cancel button. Pause symbol disappears and Start symbol appears. Programme resumes, discharges the water and spins the laundry.
If you only want to drain the water without spinning: Just press Start / Pause / Cancel button. Pause symbol
disappears. Start symbol appears. Programme resumes and discharges the water only.
4.20 End of programme
“End” appears on the display at the end of the programme. Symbols of the programme steps remain lit.Auxiliary function, spin speed and temperature that were selected at the beginning of the programme remain selected.
4.21 Your machine is equipped with a “Standby Mode”
In case of not starting any programme or waiting without making any other operation when the machine is turned on by On/Off button and while it is in selection step or if no other operation is performed approximately 2 minutes after the programme you selected has come to an end, your machine will automatically switch to energy saving mode. Brightness of indicator lights will decrease. Also, if your product is equipped with a display showing the
programme duration, this display will completely turn off. In case of rotating the Programme Selection knob or pressing any button, lights and display will restore to their previous condition. Your selections made while exiting the energy saving mode may change. Check the appropriateness of your selections before starting the programme. Readjust if necessary. This is not a fault.
16 / 68 EN |
Washing Machine / User’s Manual |
|
|
5 Maintenance and cleaning
Service life of the product extends and frequently faced problems decrease if cleaned at regular intervals.
5.1 Cleaning the detergent drawer
Remove any powder residue buildup in the drawer.To do this;
2
1
3 4
You can remove the detergent drawer by pulling it towards yourself strongly.
C If more than a normal amount of softener and liquid detergent mixture starts to remain in the softener compartment, the siphon must be cleaned.
Wash the drawer and the siphon with plenty of lukewarm water in a washbasin.Wear protective gloves or use an appropriate brush to avoid touching the residues in the drawer when cleaning. Replace the drawer into its housing after cleaning. Check if the siphon is in its original location.
5.2 Cleaning the loading door and the drum
For products with drum cleaning programme, please see
Operating the product - Programmes.
For products without drum cleaning, follow the below steps to clean the drum:
Select Additional Water or Extra Rinse auxiliary functions. Use a Cottons programme without pre-wash. Set the temperature to the level recommended on the drum cleaning agent which can be provided from authorized services. Apply this procedure without any laundry in the product. Before starting the programme, put 1 pouch of special drum cleaning agent (if the special agent could not be supplied, put max. 100 g of powder anti-limescale) into the main wash detergent compartment (compartment no. “2”). If the anti-limescale is in tablet form, put only one tablet into the main wash compartment no.“2”. Dry the inside of the bellow with a clean piece of cloth after the programme has come to an end.
C Repeat Drum Cleaning process in every 2 months.
C Use an anti-limescale suitable for the washing machines.
After every washing make sure that no foreign substance is left in the drum.
If the holes on the bellow shown in the figure is blocked, open the holes using a toothpick.
C Foreign metal substances will cause rust stains in the drum. Clean the stains on the drum surface by using cleaning agents for stainless steel. Never use steel wool or wire wool.
Awarning: Never use sponge or scrub materials.These will damage the painted and plastic surfaces.
5.3 Cleaning the body and control panel
Wipe the body of the machine with soapy water or noncorrosive mild gel detergents as necessary, and dry with a soft cloth.
Use only a soft and damp cloth to clean the control panel.
5.4 Cleaning the water intake filters
There is a filter at the end of each water intake valve at the rear of the machine and also at the end of each water intake hose where they are connected to the tap. These filters prevent foreign substances and dirt in the water to enter the washing machine. Filters should be cleaned as they do get dirty.
1.Close the taps.
2.Remove the nuts of the water intake hoses to access the filters on the water intake valves. Clean them with an
appropriate brush. If the filters are too dirty, take them out by means of pliers and clean them.
3.Take out the filters on the flat ends of the water intake hoses together with the gaskets and clean thoroughly under running water.
4.Replace the gaskets and filters carefully in their places and tighten the hose nuts by hand.
17 / 68 EN |
Washing Machine / User’s Manual |
|
|
5.5 Draining remaining water and cleaning the pump filter
The filter system in your machine prevents solid items such as buttons, coins and fabric fibers clogging the pump impeller during discharge of washing water. Thus, the water will be discharged without any problem and the service life of the pump will extend.
If the machine fails to drain water, the pump filter is clogged. Filter must be cleaned whenever it is clogged or in every 3 months.Water must be drained off first to clean the pump filter.
In addition, prior to transporting the machine (e.g., when moving to another house) and in case of freezing of the water, water may have to be drained completely.
Awarning: Foreign substances left in the pump filter may damage your machine or may cause noise problem.
In order to clean the dirty filter and discharge the water: 1. Unplug the machine to cut off the supply power.
Awarning: Temperature of the water inside the machine may rise up to 90 ºC.To avoid burning risk, filter must be cleaned after the water in the machine cools down.
2.Some of our products have emergency draining hose and some does not have. Follow the steps below to discharge the water.
Discharging the water when the product does not have an emergency draining hose:
a.Place a large container in front of the filter to catch water from the filter.
b.Loosen pump filter (anticlockwise) until water starts to flow. Fill the flowing water into the container you have placed in front of the filter. Always keep a piece of cloth handy to absorb any spilled water.
c.When the water inside the machine is finished, take out
the filter completely by turning it.
3.Clean any residues inside the filter as well as fibers, if any, around the pump impeller region.
4.Install the filter.
18 / 68 EN |
Washing Machine / User’s Manual |
|
|
6 Technical specifications
Complying Commission Delegated Regulation (EU) No 1061/2010
Supplier name or trademark |
|
Beko |
Model name |
|
WMI 81442 |
Rated capacity (kg) |
|
8 |
Energy efficiency class / Scale from A+++ (Highest Efficiency) to D (Lowest Efficiency) |
A+++ |
|
Annual Energy Consumption (kWh) (1) |
|
192 |
Energy consumption of the standard 60°C cotton programme at full load (kWh) |
1,069 |
|
Energy consumption of the standard 60°C cotton programme at partial load |
(kWh) |
0,700 |
Energy consumption of the standard 40°C cotton programme at partial load |
(kWh) |
0,680 |
Power consumption in ‘off-mode’ (W) |
|
0,200 |
Power consumption in ‘left-on mode’ (W) |
|
1,000 |
Annual Water Consumption (l) (2) |
|
11000 |
Spin-drying efficiency class / Scale from A (Highest Efficiency) to G (Lowest Efficiency) |
B |
|
Maximum spin speed (rpm) |
|
1400 |
Remaining moisture Content (%) |
|
53 |
Standard cotton programme (3) |
|
Cotton Eco 60°C and 40°C |
Programme time of the standard 60°C cotton programme at full load (min) |
|
200 |
Programme time of the standard 60°C cotton programme at partial load (min) |
175 |
|
Programme time of the standard 40°C cotton programme at partial load (min) |
175 |
|
Duration of the left-on mode (min) |
|
N/A |
Airborne acoustical noise emissions washing/spinning (dB) |
|
50/72 |
Built-in |
|
Yes |
Height (cm) |
|
82 |
Width (cm) |
|
60 |
Depth (cm) |
|
54 |
Net weight (±4 kg.) |
|
71 |
Single Water inlet / Double Water inlet |
|
• / - |
• Available |
|
|
|
|
|
Electrical input (V/Hz) |
|
230 V / 50Hz |
Total current (A) |
|
10 |
Total power (W) |
|
2200 |
Main model code |
|
8811 |
(1)Energy Consumption based on 220 standard washing cycles for cotton programmes at 60°C and 40°C at full and partial load, and the consumption of the low-power modes. Actual energy consumption will depend on how the appliance is used.
(2)Water consumption based on 220 standard washing cycles for cotton programmes at 60°C and 40°C at full and partial load. Actual water consumption will depend on how the appliance is used.
(3)“Standard 60°C cotton programme” and the “standard 40°C cotton programme” are the standard washing programmes to which the information
in the label and the fiche relates and these programmes are suitable to clean normally soiled cotton laundry and that they are the most efficient programmes in terms of combined energy and water consumption.
Technical specifications may be changed without prior notice to improve the quality of the product.
19 / 68 EN |
Washing Machine / User’s Manual |
|
|
7 Troubleshooting
Program does not start after closing the door.
• Start / Pause / Cancel button was not pressed. >>> *Press the Start / Pause / Cancel button.
Programme cannot be started or selected.
• Washing machine has switched to self protection mode due to a supply problem (line voltage, water pressure, etc.). >>> Press and hold Start / Pause button for 3 seconds to reset the machine to factory settings. (See "Cancelling the programme")
Water in the machine.
• Some water might have remained in the product due to the quality control processes in the production. >>> This is not a failure; water is not harmful to the machine.
Machine vibrates or makes noise.
•Machine might be standing unbalanced. >>> Adjust the feet to level the machine.
•A hard substance might have entered into the pump filter. >>> Clean the pump filter.
•Transportation safety bolts are not removed. >>> Remove the transportation safety bolts.
•Laundry quantity in the machine might be too little. >>> Add more laundry to the machine.
•Machine might be overloaded with laundry. >>> Take out some of the laundry from the machine or distribute the load by hand to balance it homogenously in the machine.
•Machine might be leaning on a rigid item. >>> Make sure that the machine is not leaning on anything.
Machine stopped shortly after the programme started.
• Machine might have stopped temporarily due to low voltage. >>> It will resume running when the voltage restores to the normal level.
Programme time does not countdown. (On models with display)
•Timer may stop during water intake. >>> Timer indicator will not countdown until the machine takes in adequate amount of water. The machine will wait until there is sufficient amount of water to avoid poor washing results due to lack of water. Timer indicator will resume countdown after this.
•Timer may stop during heating step. >>> Timer indicator will not countdown until the machine reaches the selected temperature.
•Timer may stop during spinning step. >>> Automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the drum.
•Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its surrounding environment. Laundry should be rearranged and re-spun.
Foam is overflowing from the detergent drawer.
•Too much detergent is used. >>> Mix 1 tablespoonful softener and ½ l water and pour into the main wash compartment of the detergent drawer.
•Put detergent into the machine suitable for the programmes and maximum loads indicated in the “Programme and consumption table”. When you use additional chemicals (stain removers, bleachs and etc), reduce the amount of detergent.
Laundry remains wet at the end of the programme
•Excessive foam might have occurred and automatic foam absorption system might have been activated due to too much detergent usage.
>>> Use recommended amount of detergent.
•Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its surrounding environment. Laundry should be rearranged and re-spun.
A |
warning: If you cannot eliminate the problem although you follow the instructions in this section, consult your dealer or the |
Authorized Service Agent. Never try to repair a nonfunctional product yourself. |
|
|
|
20 / 68 EN |
Washing Machine / User’s Manual |
|
|
Lavadora |
|
Manual del usuario |
|
WMI 81442 |
|
ES |
PT |
Número del documento= 2820525130_ES/12-10-15.(11:41) |
|
Loading...