Beko WMD 77127, WMD 77107, WMD 77087, WMD 77127 S, WMD 77107 D User manual

...

0 (0)

Washing Machine	WMD 77127
Пералня машина	WMD 77107
Perilica rublja	WMD 77087
Plně automatická pračka	WMD 77127 S
	WMD 77107 D
	WMD 77147

	1 Warnings	Safety instructions
		• This appliance must be connected to
	General Safety	• This appliance must be connected to
	• Never place your machine on a carpet	an earthed outlet protected by a fuse of
	• Never place your machine on a carpet	suitable capacity.
	covered floor. Otherwise, lack of airflow	suitable capacity.
	covered floor. Otherwise, lack of airflow	• The supply and draining hoses must
	from below of your machine may cause	• The supply and draining hoses must
	from below of your machine may cause	always be securely fastened and remain in
	electrical parts to overheat. This may cause	always be securely fastened and remain in
	electrical parts to overheat. This may cause	an undamaged state.
	problems with your washing machine.	an undamaged state.
	problems with your washing machine.	• Fit the draining hose to a washbasin or
	• If the power cable or mains plug is	• Fit the draining hose to a washbasin or
	• If the power cable or mains plug is	bathtub securely before starting up your
	damaged you must call Authorized Service	bathtub securely before starting up your
	damaged you must call Authorized Service	machine. There may be a risk of being
	for repair.	machine. There may be a risk of being
	for repair.	scalded due to high washing temperatures!
	• Fit the drain hose into the discharge	scalded due to high washing temperatures!
	• Fit the drain hose into the discharge	• Never open the loading door or remove the
	housing securely to prevent any water	• Never open the loading door or remove the
	housing securely to prevent any water	filter while there is still water in the drum.
	leakage and to allow machine to take in	filter while there is still water in the drum.
	leakage and to allow machine to take in	• Unplug the machine when it is not in use.
	and discharge water as required. It is very	• Unplug the machine when it is not in use.
	and discharge water as required. It is very	• Never wash down the appliance with a
	important that the water intake and drain	• Never wash down the appliance with a
	important that the water intake and drain	water hose! There is the risk of electric
	hoses are not folded, squeezed, or broken	water hose! There is the risk of electric
	hoses are not folded, squeezed, or broken	shock!
	when the appliance is pushed into place	shock!
	when the appliance is pushed into place	• Never touch the plug with wet hands. Do
	after it is installed or cleaned.	• Never touch the plug with wet hands. Do
	after it is installed or cleaned.	not operate the machine if the power cord
	• Your washing machine is designed to	not operate the machine if the power cord
	• Your washing machine is designed to	or plug is damaged.
	continue operating when the power	or plug is damaged.
	continue operating when the power	• For malfunctions that cannot be solved by
	restores after a power interruption. The	• For malfunctions that cannot be solved by
	restores after a power interruption. The	information in the operating manual:
	machine will resume its program when the	information in the operating manual:
	machine will resume its program when the	• Turn off the machine, unplug it, turn off
	power restores. Press the “Start/Pause/	• Turn off the machine, unplug it, turn off
	power restores. Press the “Start/Pause/	the water tap and contact an authorized
	Cancel” button for 3 seconds to cancel the	the water tap and contact an authorized
	Cancel” button for 3 seconds to cancel the	service agent. You may refer to your local
	program (See, Canceling a Program)	service agent. You may refer to your local
	program (See, Canceling a Program)	agent or solid waste collection center in
	• There may be some water in your machine	agent or solid waste collection center in
	• There may be some water in your machine	your municipality to learn how to dispose of
	when you receive it. This is from the quality	your municipality to learn how to dispose of
	when you receive it. This is from the quality	your machine.
	control process and is normal. It is not	your machine.
	control process and is normal. It is not	If there are children in your
	harmful to your machine.	If there are children in your
	• Some problems you may encounter may	house...
	be caused by the infrastructure. Press	• Keep children away from the machine
	“Start/Pause/Cancel” button for 3 seconds	when it is operating. Do not let them
	to cancel the program set in your machine	tamper with the machine.
	before calling the authorized service.	• Close the loading door when you leave the
	First Use	area where the machine is located.
	• Carry out your first washing process
	without loading your machine and with
	detergent under “Cottons 90°C” program.
	• Ensure that the cold and hot water
	connections are made correctly when
	installing your machine.
	• If the current fuse or circuit breaker is less
	than 16 Amperes, please have a qualified
	electrician install a 16 Ampere fuse or
	circuit breaker.
	• While using with or without a transformer,
	do not neglect to have the grounding
	installation laid by a qualified electrician.
	Our company shall not be liable for any
	damages that may arise when the machine
	is used on a line without grounding.
	• Keep the packaging materials out of reach
	of children or dispose them by classifying
	according to waste directives.
	Intended use
	• This product has been designed for home
	use.
	• The appliance may only be used for
	washing and rinsing of textiles that are
	marked accordingly.

2 - EN

2 Installation

Removing packaging reinforcement

Tilt the machine to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon.

Opening the transportation locks

ATransportation safety bolts must be removed before operating the washing machine! Otherwise, the machine will be damaged!

1.Loosen all the bolts with a spanner until they rotate freely (“C”)

2.Remove transportation safety bolts by turning them gently.

3.Fit the covers (supplied in the bag with the Operation Manual) into the holes on the rear panel. (“P”)

C Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future.

C Never move the appliance without the transportation safety bolts properly fixed in place!

Adjusting the feet

ADo not use any tools to loosen the lock nuts. Otherwise, they can be damaged.

1.Manually (by hand) loosen the lock nuts on the feet.

2.Adjust them until the machine stands level and firmly.

3.Important: Tighten all lock nuts up again.

•If you are going to use your double waterinlet machine as a single (cold) water-inlet unit, you must install the stopper*, supplied with your machine to the hot water valve.

•If you want to use both water inlets of the product, you can connect the hot water hose after removing the stopper and gasket group from the hot water valve.

* Applies for the products supplied with a blind stopper group.

•Models with a single water inlet should not be connected to the hot water tap.

When returning the appliance to its place after maintenance or cleaning, care should be taken not to fold, squeeze or block the hoses.

Connecting to the drain

The water discharge hose can be attached to the edge of a washbasin or bathtub. The drain hose should be firmly fitted into the drain as to not get out of its housing.

Important:

•The end of the drain hose must be directly connected to the wastewater drain or to the washbasin.

•The hose should be attached to a height of at least 40 cm, and 100 cm at most.

•In case the hose is elevated after laying it on the floor level or close to the ground (less than 40 cm above the ground), water discharge becomes more difficult and the laundry may come out wet.

Connecting to the water supply.

Important:

•The water supply pressure required to run the machine must be 1-10 bar (0,1 – 1 MPa).

•Connect the special hoses supplied with the machine to the water intake valves on the machine.

•The hose should be pushed into the drainage for more than 15 cm. If it is too long you may have it shortened.

•The maximum length of the combined hoses must not be longer than 3.2 m.

3 - EN

Electrical connection

Connect the machine to an earthed outlet protected by a fuse of suitable capacity.

Important:

•Connection should comply with national regulations.

•The voltage and the allowed fuse protection are specified in the section “Technical Specifications”.

•The specified voltage must be equal to your mains voltage.

•Connection via extension cords or multi-

plugs should not be made.

BA damaged power cable must be replaced by a qualified electrician.

BThe appliance must not be operated unless it is repaired! There is the risk of electric shock!

3 Initial preparations for

washing

Preparing clothes for washing

Laundry items with metal attachments such as, bras, belt buckles and metal buttons will damage the machine. Remove metal attachments or place the items in a clothing bag, pillow case, or something similar.

•Sort the laundry according to type of fabric, color, and degree of soiling and permissible water temperature. Always follow the advice on the garment labels.

•Place small items like infants’ socks and nylon stockings, etc. in a laundry bag, pillow case or something similar. This will also save your laundry from getting lost.

•Wash “machine washable” or “hand washable” labeled products only with an appropriate program.

•Do not wash colors and whites together. New, dark colored cottons may release a lot of dye. Wash them separately.

•Use only dyes/color changers and lime removers suitable for machine wash. Always follow the instructions on the packaging.

•Wash trousers and delicate clothes turned inside out.

Correct load capacity

C Please follow the information in the "Program Selection Table". Washing results will degrade when the machine is overloaded.

Loading door

The door locks during program operation and the Door Locked Symbol lights up. The door can be opened when the symbol fades out.

Detergents and softeners

Detergent Drawer

The detergent drawer is composed of three compartments:

The detergent dispenser may be in two different types according to the model of your machine.

–(I) for prewash

–(II) for main wash - (III) siphon

–() for softener

Detergent, softener and other cleaning agents

Add detergent and softener before starting the washing program.

Never open the detergent dispenser drawer while the washing program is running!

When using a program without pre-wash, no detergent should be put into the pre-wash compartment (Compartment no. I).

Detergent quantity

The amount of washing detergent to be used depends on the amount of laundry, the degree of soiling and water hardness.

•Do not use amounts exceeding the quantities recommended on the package to avoid problems of excessive foam, poor rinsing, financial savings and finally, environmental protection.

•Never exceed the (> max <) level marking; otherwise, the softener will be wasted without being used.

•Do not use liquid detergent if you want to wash using the time delay feature.

4 - EN

5 Selecting a Program and Operating Your Machine

Control panel

Figure 1

1	2	3	4	5

Spin Speed Adjustment Button

On/Off Button

Display

Time Delaying Button (+/-)

Temperature Adjustment Button

Auxiliary Function Buttons

Program Selection Knob

Start/Pause/Cancel Button

Display symbols

Figure 2

2.a

- Spin Speed Indicator

2.b- Temperature Indicator

2.c

- Spin Symbol

2.d- Temperature Symbol

2.e

- Remaining Time and Delaying Time

Indicator

2.f

- Program Indicator Symbols (pre-wash/

main wash/rinse/softener/spin)

2.g

- Economy Symbol

2.h

- Time Delaying Symbol

2.i

- Door Locked Symbol

2.j

- Start Symbol

2.k

- Standby Symbol

2.l

- Auxiliary Function Symbols

Turning the machine on

speed for the selected program appear. Press

Plug in your machine. Turn the tap on

"Start/Pause/Cancel" button to start the

completely. Check if the hoses are connected

program.

tightly. Place the laundry in the machine. Add

Main programs

detergent and softener. Press the “On/Off”

Depending on the type of textile, the following

button.

main programs are available:

Program selection

• Cottons

You can wash your durable clothes with this

Select the appropriate program from the

program. Your laundry will be washed with

program table according to type, amount and

vigorous washing movements during a longer

degree of soiling of the laundry and washing

washing cycle. It is recommended for your

temperatures.

cotton items (such as bed sheets, duvet and

Turn the Program Selection Knob to the

pillowcase sets, bathrobes, underclothing,

program mode that you wish to wash your

etc.).

laundry.

• Synthetics

The recommended temperature and spin

You can wash your less durable clothes on this

5 - EN

program. Gentler washing movements and a shorter washing cycle is used compared to the “Cottons” program. It is recommended for your synthetic clothes (such as shirts, blouses, synthetic/cotton blended garments, etc.). For curtains and lace, the “Synthetic 40” program with pre-wash and anti-creasing functions selected is recommended. Detergent should not be put in the pre-wash compartment. Less detergent should be put in the main wash compartment as loose knit fabrics (lace) foam too much due to its meshed structure.

• Woollens

You can wash your machine-washable woolen garments on this program. Wash by selecting the proper temperature according to the labels of your clothes. It is recommended to use appropriate detergents for woolens.

Additional programs

For special cases, there are also extra programs available:

C Additional programs may differ according to the model of your machine.

• Babycare

Increased hygiene is provided by a longer heating period and an additional rinse cycle. It is recommended for baby clothes and clothes worn by allergic people.

• Hand wash

You can wash your woolen/delicate clothes that bear “not machinewashable” labels for which hand wash is recommended on this program. It washes the laundry with very tender washing movements without damaging your clothes.

• Daily Xpress

You can use this program to quickly wash a small number of lightly soiled and unstained cotton garments. E.g.: bathrobes, duvet covers, sport wear, daily clothes and etc. used only once.

• Super 40

This program washes for a longer period at 40°C and gives the same result as the

“Cottons 60°C” program, thus it saves energy. It is suitable for clothes for which you cannot use the “Cottons 60°C” program.

• Darkcare

Use this programme to wash your dark coloured laundry, or the coloured laundry that you do not want them get faded. This programme washes your laundry with low mechanical movements and at low temperature. We recommend you to use

liquid detergent or woolen shampoo for dark coloured laundry.

• Mix 40

You can use this program to wash cottons and synthetics together. There is no need to sort them.

• Intensive

You can wash your durable and heavily soiled clothes on this program. In this program, your clothes will be washed for a longer time and an extra rinse cycle will be made compared to the “Cottons” program. You can use it for your heavily soiled clothes that you wish to be rinsed gently.

Economy Symbol

Shows energy saving programs and temperature selections.

As "Intensive" and "Hygiene" programs are long programs with higher temperature selections to ensure hygiene, “Economy” Symbol will not light up.

Special programs

For specific applications, select any of the following programs:

• Rinse

This program is used when you want to rinse or starch separately.

• Spin + Drain

This program spins with maximum possible rpm in the default setting after the water drains from the machine.

C Use a lower spin speed for delicate laundries.

Temperature selection

Whenever a new program is selected, the temperature anticipated for that program appears on the temperature indicator (7b).

To change the temperature, press the temperature button. Temperature decreases in 10° increments.

Cold selection is shown with “-” symbol.

		Normally soiled, white cottons and
	90˚C	linens. (Ex.: coffee table covers,
		tablecloths, towels, bed sheets)
		Normally soiled, fade proof colored
		linens, cottons or synthetic clothes
	60˚C	(Ex.: shirts, nightgowns, pajamas)
		and lightly soiled white linen clothes
		(Ex.: underwear)
	40˚C	Blended clothes including
	40˚C	synthetics and woolens as well as
	30˚C Cold	synthetics and woolens as well as
	30˚C Cold	delicates.
		delicates.

Spin Speed selection

Whenever a new program is selected, the maximum spin speed of the selected program is displayed on the spin speed indicator.

To decrease the spin speed, press the “Spin” button. Spin speed decreases gradually. Then, rinse hold and no spin options are shown respectively.

Rinse hold is shown with “” and no spin is

shown with “” symbols.

If you are not going to unload your clothes

6 - EN

immediately after the cycle, you may use rinse hold function in order to prevent your clothes become wrinkled when there is no water in the machine. With this function, your laundry is kept in the final rinsing water. If you want to spin your laundry after the rinse hold function:

-Adjust the spin speed.

Program and consumption table

-Press “Start/Pause/Cancel” button. Program resumes. Your machine drains the water and spins your laundry.

You can use no spin function in order to drain the water without spinning at the end of the program.

Programme

Cottons

Intensive

Babycare

Synthetics

Mix 40

Woollens

Super 40

Hand wash

Daily Xpress

Darkcare

	<![if ! IE]> <![endif]>Max. Load (kg)
90	7
60**	7
40	7
60	7
90	7
60	3
40	3
40	3.5
40	1.5
40	7
30	1
90	7
60	7
30	7
40	3

<![if ! IE]> <![endif]>Water Consumption (l)	<![if ! IE]> <![endif]>Energy Consumption (kWh)	<![if ! IE]> <![endif]>Spin speed (rpm)		Auxiliary functions
				Auxiliary functions
			<![if ! IE]> <![endif]>Prewash		<![if ! IE]> <![endif]>Quick Wash	<![if ! IE]> <![endif]>Rinse Plus	<![if ! IE]> <![endif]>Anti-Creasing	<![if ! IE]> <![endif]>Plus water	<![if ! IE]> <![endif]>Rinse Hold
54	2.70	max.	•		•	•	•	•	•
52	1.19	max.	•		•	•	•	•	•
64	0.72	max.	•		•	•	•	•	•
66	1.40	max.				*	•		•
66	2.70	max.				*			•
45	1.00	1000	•		•	•	•	•	•
45	0.45	1000	•		•	•	•	•	•
45	0.55	1000	•		•	•	•	•	•
56	0.30	600				•		•	•
52	0.90	max.							•
40	0.25	600
60	2.00	max.				•			•
		***
60	1.15	max.				•			•
		***
70	0.20	max.				•			•
		***
82	0.55	800				*			•

Selectable temperature range °C

90-Cold

60-40

90-30

60-Cold

40-Cold

30-Cold

90-Cold

40-Cold

• : Selectable

* : Automatically selected, not cancellable.

**: Energy Label program (EN 60456)

***: 1400 rpm in machines with a spin speed higher than 1400 rpm. It spins with max. rpm in machines with a spin speed lower than 1400 rpm.

- : See program description for maximum load.

C The auxiliary functions in the table vary according to the model of your machine.

C Water and power consumption and program duration differ from the table subject to changes in water pressure, water hardness and temperature, ambient temperature, type and amount of laundry, selection of auxiliary functions, and changes in supply voltage.

C Program duration will be displayed on the screen of your machine according to your selection.

7 - EN

Auxiliary functions

Auxiliary function selection

If an auxiliary function that should not be selected together with a previously selected function is chosen, the first selected function will be cancelled and the last auxiliary function selection will remain active.

Ex.: If you want to select pre-wash first and then quick wash, pre-wash will be cancelled and quick wash will remain active.

Auxiliary function that is not compatible with the program cannot be selected. (see, “Program Selection Table”)

• Prewash

When you select this function, the display will indicate "F1" symbol.

•A pre-wash is only worthwhile for heavily soiled laundry. Without pre-wash you save energy, water, detergent and time.

•Pre-wash without detergent is recommended for lace and curtains.

•Quick Wash

With this function, the wash time is shortened. "F2” symbol lights up on the display.

•Use this function for smaller amounts or slightly soiled laundries.

•Rinse Plus

When this function is selected, washing and rinsing is performed with plenty of water. "F3” symbol lights up on the display.

• Plus water

When this function is selected, washing and rinsing is made with plenty of water in “Cottons”, “Synthetics”, “Delicates” and “Woolens” programs.

C Use this function for delicate laundries that crease easily.

C Whenever you select this auxiliary function, load your machine with half of the maximum laundry specified in the program table.

• Anti-Creasing

With this function, drum movement will be lessened to prevent creasing and spinning speed is limited. In addition, washing is carried out at a higher water level. "F4” symbol lights up on the display.

• Use this function for delicate laundries that crease easily.

C Whenever you select this auxiliary function, load your machine with half of the maximum laundry specified in the program table.

Time display

The display shows the time remaining for the program to complete while a program is running. Time is displayed in hours and minutes as “01:30”.

Time delay

With the “Time delay” function you can delay the program start up to 24 hours. Setting can be made in intervals of 30 minutes.

Open the loading door, place the laundry inside and fill detergent drawer. Set the washing program, temperature, spin speed and, if required, select the auxiliary functions. Press “Time delaying” buttons “+” and “-” to set your desired time delay. The Time delaying symbol will flash. Press “Start/Pause/Cancel” button. Then the time delay starts to count down. The Time delaying symbol will light up. The Start symbol will light up.

The “:” in the middle of the displayed time delay will start to flash.

•More laundry may be loaded or taken out during the time delay period. At the end of the time delay countdown process, time delaying symbol fades and the washing starts as the program duration is displayed.

Changing the delay time

If you want to change the time during the countdown:

Press “Start/Pause/Cancel” button. “ : “ in the middle of the screen will stop flashing. The Standby symbol will light up. The Time delaying symbol will flash. The Start Symbol will fade. Press “Time delaying” buttons “+” or “-” to set your desired time delay. Press “Start/ Pause/Cancel” button. The Time delaying symbol will light up. The Standby symbol will fade. The Start symbol will light up.The “:” in the middle of the displayed time delay will start to flash.

Canceling the time delay

If you want to cancel the time delay countdown and start the program immediately:

Press “Start/Pause/Cancel” button. The “:” in the middle of the displayed time delay will stop flashing. Start symbol will fade. The standby symbol and the time delaying symbol will flash. Press time delaying button “-” to decrease the desired time delay. Program duration after 30 minutes shall be displayed. Press Start/Pause/ Cancel Button to start the program.

Starting the Program

Press Start/Pause/Cancel button to start the program. The start symbol which indicates that the program has started will light up.

The door locks and the door locked symbol will light up. The Symbol of the relevant step (prewash, main wash, rinse, softener and spin) that the program has started from will light up.

8 - EN

Changing the selections after the program has started

The selected spin speed and program temperature fade out. An empty frame appears.

When the “Program selection” button is brought to the appropriate position, rpm and temperature data reappear.

Switching the machine to standby mode

The machine is switched to standby mode by pressing “Start/Pause/Cancel” button momentarily. The Standby symbol which indicates the machine is in standby mode lights up and the start symbol that shows the program has started and is still continuing fades out.

Selecting or canceling an auxiliary function in pause mode

Auxiliary functions can be cancelled or selected in accordance with the step the program is at.

Adding/removing laundry in pause mode

The door can be opened if the water level is suitable. The door locked symbol will light up until the door is suitable for opening. This symbol will fade out as soon as the door is allowed to open. Laundry may be added / taken out by opening the door.

Door lock

The Door Locked Symbol lights up when the loading door is locked. This symbol will flash until the door is allowed to open. Do not force the door at this stage. This symbol will fade out as soon as the door is allowed to open. You may open the door after the symbol fades out.

Child-proof lock

Protect the appliance from being tampered by children by means of the child-proof lock. In this case, no change can be made in the running program.

C Your machine can be turned on and off with On/Off button while the child-proof lock is activated. In this case, your machine will resume its program with child-proof lock activated.

The machine is switched to child-lock by pressing the 2nd and 4th auxiliary functions for 3 sec. “C:on” (Child-proof lock is activated) label appears on the display.

The same symbol will also be displayed whenever any button is pressed while the machine is child-locked.

To deactivate the child-proof lock, press the 2nd and 4th auxiliary function buttons for 3

sec.

“C:OFF” (Child-proof lock is deactivated) label appears on the screen.

Ending the program through canceling

“Start/Pause/Cancel” button (Figure 2-10) is pressed for 3 seconds to cancel the program. Start symbol (Figure 3-7j) will flash during cancellation. After cancellation, the symbol of the corresponding step at which the

cancellation was made will remain lit and “End” will appear on the screen.

End of program

When the program is finished, the symbols of the relevant steps will remain lit up and the auxiliary function, spin and temperature data selected at the start-up of the program will remain selected. “End” will appear on the display.

9 - EN

5 Maintenance and cleaning

Detergent Drawer

Remove any powder residue buildup in the drawer. To do this;

1.Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine.

CIf more than a normal amount of water and softener mixture starts to gather in the softener compartment, the siphon must be cleaned.

2.Wash the dispenser drawer and the siphon with plenty of lukewarm water in a washbasin.

3.Replace the drawer into its housing after cleaning. Check if the siphon is in its original location.

Inlet water filters

There is a filter at the end of each water intake valve at the back side of the machine and also at the end of each water intake hose where they are connected to the tap. These filters prevent the foreign substances and dirt in the water to enter into the machine. Filters should be cleaned as they get dirty.

•Close the taps.

•Remove the nuts of the water intake hoses to clean the surfaces of the filters on the water intake valves with an appropriate brush.

•If the filters are very dirty, you can pull them out by means of pliers and clean them.

•Take out the filters on the flat ends of the water intake hoses together with the gaskets and clean thoroughly under streaming water.

•Replace the gaskets and filters carefully to their places and tighten the hose nuts by hand.

Draining any remaining water and cleaning the pump filter

Your product is equipped with a filter system which ensures a cleaner water discharge that extends pump life by preventing solid items such as buttons, coins and fabric fibers from clogging the pump propeller during discharge of the washing water.

•If your machine fails to drain the water, the pump filter may be clogged. You may have to clean it every 2 years or whenever it is plugged. Water must be drained off to clean the pump filter.

In addition, water may have to be drained off completely in the following cases:

•before transporting the machine (e.g. when moving house)

•when there is the danger of frost

In order to clean the dirty filter and discharge the water;

1- Unplug the machine to cut off the supply power.

AThere may be water at 90°C in the machine. Therefore, the filter must be cleaned only after the inside water is cooled down to avoid hazard of scalding.

2- Open the filter cap. The filter cap may be composed of one or two pieces according to the model of your machine.

If it is composed of two pieces, press the tab on the filter cap downwards and pull the piece out towards yourself.

If it is composed of one piece, hold it from both sides and open it by pulling out.

3- An emergency drain hose is supplied with some of our models. Others are not supplied with this item.

If your product is supplied with an emergency drain hose, do the following as shown in the figure below:

•Pull out the pump outlet hose from its housing.

•Place a large container at the end of the hose. Drain the water off into the container

10 - EN

by pulling out the plug at the end of the hose. If the amount of water to be drained off is greater than the volume of the container, replace the plug, pour the water out, then resume the draining process.

•After draining process is completed, replace the plug into the end of the hose and fit the hose back into its place.

If your product is not supplied with an emergency drain hose, do the following as shown in the figure below:

•Place a large container in front of the filter to receive water flowing from the filter.

•Loosen pump filter (anticlockwise) until water starts to flow out of it. Direct the flowing water into the container you have placed in front of the filter. You can use a piece of cloth to absorb any spilled water.

•When there is no water left, turn the pump filter until it is completely loose and remove it.

•Clean any residues inside the filter as well as fibers, if any, around the propeller region.

•If your product has a water jet feature, be sure to fit the filter into its housing in the pump. Never force the filter while replacing it into its housing. Fit the filter fully into its housing; otherwise, water may leak from the filter cap.

4- Close the filter cap.

Close the two-piece filter cap of your product by pushing the tab on it.

Close the one-piece filter cap of your product by fitting the tabs on the bottom into their positions and pushing the upper part of it.

11 - EN

6 Solution suggestions for problems


Problem	Cause	Explanation / Suggestion
	Machine may have switched
Program cannot	to self protection mode due to	Reset your machine by pressing “Start/Pause/
be started or	an infrastructure problem (such	Cancel” button for 3 seconds. (see, Canceling a
selected.	as line voltage, water pressure,	Program)
	etc.).
There is water		Be sure the seals of the water inlet hoses are
coming from the	There might be problems with	securely fitted.
bottom of the	hoses or the pump filter.	Tightly attach the drain hose to the tap.
machine.		Make sure that the pump filter is completely closed.

Machine stopped	Machine can stop temporarily	It will resume operating when the voltage is back to
shortly after the	due to low voltage.	the normal level.
program started.	due to low voltage.	the normal level.
		The automatic spin correction system might have
It continuously		been activated due to the unbalanced distribution of
spins.		the laundry in the drum.
Remaining time	There may be an imbalance of	The laundry in the drum may be clustered (bundled
does not count	There may be an imbalance of	laundry in a bag). Laundry should be rearranged and
down.	laundry in the machine.	re-spun.
(For models with		No spinning is performed when the laundry is
a display)		not evenly distributed in the drum to prevent any
		damage to the machine and to its environment.

	In the case of a paused
	countdown while taking in	The machine will wait until there is a sufficient
	water:	amount of water to avoid poor washing results due
	Timer will not countdown until	to lack of water. Then the timer will start to count
	the machine is filled with the	down.
	correct amount of water.
	In the case of a paused
It continuously	countdown at the heating step:
It continuously	Time will not count down until
washes.	Time will not count down until
washes.	the selected temperature for
Remaining time	the selected temperature for
Remaining time	the program is reached
does not count	the program is reached
does not count
down.		The automatic spin correction system might have
(For models with		The automatic spin correction system might have
a display)	In the case of a paused	been activated due to the unbalanced distribution of
	In the case of a paused	the laundry in the drum.
	countdown at the spinning	The laundry in the drum may be clustered (bundled
	step:	laundry in a bag). Laundry should be rearranged and
	There may be an imbalance of	re-spun.
	laundry in the machine.	No spinning is performed when the laundry is
		not evenly distributed in the drum to prevent any
		damage to the machine and to its environment.

12 - EN

Beko WMD 77127, WMD 77107, WMD 77087, WMD 77127 S, WMD 77107 D User manual

7 Specifications

Models	<![if ! IE]> <![endif]>WMD 77127	<![if ! IE]> <![endif]>WMD 77107	<![if ! IE]> <![endif]>WMD 77087	<![if ! IE]> <![endif]>WMD 77127 S	<![if ! IE]> <![endif]>WMD 77107 D	<![if ! IE]> <![endif]>WMD 77147

Maximum dry laundry capacity (kg)	7	7	7	7	7	7

Height (cm)	84	84	84	84	84	84

Width (cm)	60	60	60	60	60	60

Depth (cm)	54	54	54	54	54	54

Net Weight (kg)	72	72	71	72	72	70
Electricity (V/Hz.)			230 V / 50Hz
Total Current (A)	10	10	10	10	10	10
Total Power (W)			2200
Spinning cycle (rpm max.)	1200	1000	800	1200	1000	1400

Specifications of this appliance may change without notice to improve the quality of the product. Figures in this manual are schematic and may not match your product exactly.

Values stated on the machine labels or in the documentation accompanying it are obtained in laboratory in accordance with the relevant standards. Depending on operational and environmental conditions of the appliance, values may vary.

This appliance’s packaging material is recyclable. Help recycle it and protect the environment by dropping it off in the municipal receptacles provided for this purpose. Your appliance also contains a great amount of recyclable material. It is marked with this label to indicate the used appliances that should not be mixed with other waste. This way, the appliance recycling organised by your manufacturer will be done under the best possible conditions, in compliance with European Directive 2002/96/EC on Waste Electrical and Electronic Equipment. Contact your town hall or your retailer for the used appliance collection points closest to your home. We thank you doing your part to protect the environment.

On/Off

Start

Reset

Cottons

Synthetics

Woollens

Delicate

Babycare

Sport

Shirt

Hand

Pet hair

Daily

Pause

3 sec.

wash

removal

Xpress

Intensive

Rinse

Quick

Duvet

Anti

Rinse

Time

Temperature

Cold

Cotton

Darkcare

hold

wash

creasing

plus

delay

heat

Economic

Prewash

Main

Rinse

Drain

Spin

Door

Wash

End

Child

Conditioner

Fasion

wash

spin

ready

proof lock

Care

<![if ! IE]>

<![endif]>2820520982_EN/180809.0920

13 - EN

1 Предпазни мерки

Обща безопасност

•Никога не поставяйте пералнята на под, покрит с килим. В противен случай

възпрепятстването на достъпа на въздух отдолу може да доведе до прегряване на електрическите части и проблеми с пералната Ви машина.

•Ако захранващият кабел или шепсел са повредени, се свържете с оторизирания сервиз за ремонт.

•Наместете внимателно маркуча за източване в отводното гнездо за да избегнете изтичане на вода, като същевременно позволите на пералнята правилно да вкарва и изкарва вода. Много е важно маркучите за входяща и изходяща вода да не се прегънат, притиснат или пречупят при преместването на пералнята след нейното инсталиране или почистване.

•Вашата перална машина е настроена да продължи работата си след прекъсване на електрическото захранване. Пералнята няма да започне програмата отначало след възобновяване на захранването. Натиснете бутона Старт/Пауза/Отказ за 3 секунди за да откажете програмата (Виж “Отказ на програма”)

•Възможно е, при получаването на пералнята Ви, в нея да има известно количество вода, останало след процедурите за качествен контрол. Това е нормално и не вреди на пералнята Ви.

•Може възникналите проблеми да са причинени от външен проблем. Натиснете бутона Старт/Пауза/Отказ за 3 секунди за да откажете програмата, зададена в пералнята, преди да се обадите в оторизирания сервиз.

Първо ползване

•При първото ползване на пералната машина сложете перилен препарат без да зареждате пералнята с пране и пуснете на програма “Памучни тъкани 90°C”

•Уверете се, че отводите за топла и студена вода са свързани правилно при инсталацията.

•Ако бушонът или прекъсвачът Ви са под 16 Ампера, моля повикайте квалифициран електротехник да инсталира 16-Амперов бушон или прекъсвач.

•При употреба с или без трансформатор, уверете се, че заземяването на инсталацията е извършено от квалифициран електротехник. Фирмата ни не носи отговорност за повреди, възникнали в следствие на включване на пералнята в незаземен контакт.

•Дръжте опаковъчните материали от пералнята далеч от деца или ги изхвърлете в съответствие с изискванията за разделно изхвърляне на отпадъци.

Желателна употреба

•Този уред е предназначен за домашна употреба.

•Този уред може да се ползва за пране и

изплакване само на текстилни тъкани, означени по съответния начин.

Инструкции за безопасност

•Уредът трябва да бъде свързан към заземен контакт, защитен с предпазител с подходящ капацитет.

•Маркучите за входяща и изходяща вода трябва винаги да са надлежно свързани и невредими.

•Поставете внимателно изходящия маркуч

вмивката или ваната преди да стартиратe пералнята. Съществува риск от изгаряне поради високите температури на пране!

•Никога не отваряйте вратата на пералнята за да извадите филтъра ако в резервоара има останала вода.

•Извадете щепсела от контакта когато не ползвате нашината.

•Никога не мийте пералнята с маркуч за вода! Съществува риск от електрически удар!

•Никога не пипайте щепсела с мокри ръце. Не използвайте пералнята ако захранващият кабел или щепсел са повредени.

•При неизправности, за които информацията

втова ръководство не дава решение:

•Изключете пералнята, извадете щепсела от контакта, затворете крана за водата и се свържете с оторизирания сервиз. Може да се обърнете към местния агент или голям център за събиране на отпадъци в общината Ви, за да се информирате по какъв начин да изхвърлите пералнята.

Ако в дома си имате деца...

•Дръжте децата далеч от пералнята когато тя работи. Не им позволявайте да си играят с пералната машина.

•Затваряйте вратата на пералнята когато не се намирате близо до нея.

15 - BG

2 Инсталация

Отстраняване на подсилващите опаковъчни материали

Наклонете пералнята за да отстраните подсилващите опаковъчни материали като издърпате опаковъчната лента.

Отваряне на болтовете за транспортиране

AБолтовете за обезопасяване при транспортиране трябва да бъдат свалени преди работа с пералната машина! В противен случай ще повредите пералнята!

1.Разхлабете винтовете с гаечен ключ докато започнат да се въртят свободно

(“C”)

2.Отстранете винтовете за обезопасено пренасяне като ги развиете внимателно.

3.Наместете капачките (намират се в пакета с упътването) в дупките от винтовете на задния панел. (“P”)

C Съхранявайте болтовете за обезопасено транспортиране, за да може да ги ползвате отново ако се налага пренасяне на пералнята в бъдеще.

C Никога не пренасяйте пералнята без да сте завили правилно болтовете по местата им!

Регулиране на крачетата

AНе използвайте никакви уреди за разхлабване на контрагайките. В противен случай може да ги повредите!

1.Разхлабете ръчно (с ръка) контрагайките на крачетата.

2.Нагласете ги така, че пералнята да бъде нивелирана и стабилна.

3.Важно: Затегнете отново всички контрагайки.

Свързване към водното захранване

Важно:

•Необходимото водно налягане за работа на пералнята трябва да е 1-10 бара (0,1 – 1 мегапаскала).

•Свържете специалните маркучи, които се доставят заедно с пералната машина, към входящите отвори за водно захранване, разположени върху пералнята.

•За да се избегнат течове, които могат да възникнат по местата на свръзка, са осигурени гумени уплътнители (4

уплътнителя за моделите с двойно водно захранване и 2 уплътнителя за другите модели), закрепени към маркучите. Тези уплътнители се поставят на двата края на маркуча, откъм крана и откъм пералнята. Правият накрайник на маркуча, оборудван с филтър, се свързва с крана, а кривият накрайник се свързва с пералнята. Затегнете добре гайките на маркуча с ръка; никога не използвайте гаечен ключ за завиването им.

•Моделите с единично водно захранване не се свързват с кран с топла вода.

Когато връщате уреда на мястото му след ремонт или почистване, трябва да внимавате да не прегънете, притиснете или блокирате маркучите.

Свързване към отводнителната система

Маркучът за изходящата вода може да се прикрепи към страничната стена на кухненска мивка или вана. Изходящият маркуч трябва да се закрепи стабилно в отводнителната тръба за да не се изскубне от гнездото си.

Важно:

•Накрайникът на изходящия маркуч трябва да е свързан директно с канала за мръсна вода или мивката.

•Маркучът трябва да се инсталира на наймалко 40 см и най-много 100 см височина.

•В случай, че маркучът е повдигнат след като е поставен на нивото на земята (помалко от 40см над земята), източването на водата се затруднява и прането може да остане мокро.

•Поне 15см от маркуча трябва да се намират в отводната тръба. Ако е твърде дълъг, може да го скъсите.

•Максималната дължина на свързаните

16 - BG

+ 36 hidden pages