For assistance or to order, call (800) 531-5782
P T 6 2 10 S e r i e s
Application Notes
Mechanical Outline
Product Selector Guide
2 AMP ADJUSTABLE POSITIVE STEP-DOWN |
Revised 5/15/98 |
|
INTEGRATED SWITCHING REGULATOR |
||
|
||
|
|
•90% Efficiency
•Adjustable Output Voltage
•Internal Short Circuit Protection
•Over-Temperature Protection
•On/Off Control (Ground Off)
•Small SIP Footprint
•Wide Input Range
The PT6210 Series is a line of High-Performance 2 Amp, 12-Pin SIP (Single In-line Package) Integrated
Switching Regulators (ISRs) designed to meet the on-board power conversion needs of battery powered
or other equipment requiring high efficiency and small size. This high performance ISR family offers a unique combination of features combining 90% typical efficiency with open-collector on/off control and adjustable output voltage. Quiescent current in the shutdown mode is typically less than 100µA.
Pin-Out Information Ordering Information
Standard Application
VOADJ
|
|
12 |
|
|
VIN |
2,3,4 |
PT6210 |
9,10,11 |
VOUT |
|
1 |
|
|
|
|
|
|
|
C1 |
5,6,7,8 |
+ |
|
C2 |
|
INH |
Q1 |
|
COM |
|
COM |
Pin |
Function |
PT6211¨ = +5.1 Volts |
|
1 |
Inhibit |
PT6212¨ = +5.0 Volts |
|
|
(30V max) |
PT6213¨ = +3.3 Volts |
|
2 |
Vin |
||
PT6214¨ = +12 Volts |
|||
3 |
Vin |
||
|
|||
4 |
Vin |
|
|
5 |
GND |
|
|
6 |
GND |
|
|
7 |
GND |
Pkg Style 200 |
8GND
9Vout
C1 |
= Optional 1µF ceramic |
10 |
Vout |
|
C2 |
= Required 100µF electrolytic |
11 |
Vout |
|
Q1 |
= NFET |
|||
12 |
Vout Adj |
|||
|
|
Specifications
PT Series Suffix (PT1234X)
Case/Pin
Configuration
Vertical Through-Hole |
P |
Horizontal Through-Hole |
D |
Horizontal Surface Mount |
E |
Note: Heat spreaders are not electrically connected to product.
Note: Back surface of product is conducting metal.
Characteristics |
|
|
|
PT6210 SERIES |
|
|
|
(Ta = 25°C unless noted) |
Symbols |
Conditions |
|
Min |
Typ |
Max |
Units |
|
|
|
|
|
|
|
|
Output Current |
Io |
Over Vin range |
|
0.1* |
— |
2.0 |
A |
Short Circuit Current |
Isc |
Vin = Vin min |
|
— |
5.0 |
— |
Apk |
Input Voltage Range |
Vin |
0.1 ≤ Io ≤ 2.0 A |
Vo = 3.3V |
9 |
— |
26 |
V |
(Note: inhibit function cannot |
|
|
Vo = 5V |
9 |
— |
30/38** |
V |
be used with Vin above 30V.) |
|
|
Vo = 12V |
16 |
— |
30/38** |
V |
Output Voltage Tolerance |
Vo |
Over Vin Range, Io = 2.0 A |
|
— |
±1.0 |
±2.0 |
%Vo |
|
|
Ta = 0°C to +60°C |
|
|
|
|
|
Line Regulation |
Regline |
Over Vin range |
|
— |
±0.25 |
±0.5 |
%Vo |
Load Regulation |
Regload |
0.1 ≤ Io ≤ 2.0 A |
|
— |
±0.25 |
±0.5 |
%Vo |
Vo Ripple/Noise |
Vn |
Vin = Vin min |
|
— |
±2 |
— |
%Vo |
Transient Response |
ttr |
50% load change |
|
— |
100 |
200 |
µSec |
with Co = 100µF |
Vos |
Vo over/undershoot |
|
— |
5.0 |
— |
%Vo |
Efficiency |
η |
Vin=9V, Io = 0.5 A |
Vo = 3.3V |
|
|
Vin=9V, Io = 0.5 A |
Vo = 5V |
|
|
Vin=16V, Io = 0.5 A |
Vo = 12V |
— |
84 |
— |
% |
— |
89 |
— |
% |
— |
91 |
— |
% |
Switching Frequency |
ƒo |
Over Vin and Io ranges |
|
450 |
— |
900 |
kHz |
Shutdown Current |
Isc |
Vin = 16V |
|
— |
100 |
— |
µA |
Quiescent Current |
Inl |
Io = 0A, Vin =10V |
|
— |
10 |
— |
mA |
Output Voltage |
Vo |
Below Vo |
|
See Application Notes. |
|
|
|
Adjustment Range |
|
Above Vo |
|
|
|
|
|
Absolute Maximum |
Ta |
|
|
-40 |
— |
+85 |
°C |
Operating Temperature Range |
|
|
|
|
|
|
|
Recommended Operating |
Ta |
Free Air Convection, (40-60LFM) Vo= 3.3V/5V |
-40 |
— |
+85*** |
°C |
|
Temperature Range |
|
At Vin= 24V, Io=1.5A |
Vo= 12V |
-40 |
— |
+75*** |
°C |
Thermal Resistance |
θja |
Free Air Convection (40-60LFM) |
|
— |
40 |
— |
°C/W |
Storage Temperature |
Ts |
— |
|
-40 |
— |
+125 |
°C |
Mechanical Shock |
— |
Per Mil-STD-883D, Method 2002.3, |
— |
500 |
— |
G’s |
|
|
|
1 msec, Half Sine, mounted to a fixture |
|
||||
|
|
|
|
|
|
||
Mechanical Vibration |
— |
Per Mil-STD-883D, Method 2007.2, |
— |
10 |
— |
G’s |
|
|
|
20-2000 Hz, Soldered in a PC board |
|
||||
|
|
|
|
|
|
||
Weight |
— |
— |
|
— |
6 |
— |
grams |
*ISR will operate to no load with reduced specifications.
**Input voltage cannot exceed 30V when the inhibit function is used. *** See Thermal Derating chart
Note: The PT6210 Series requires a 100µF electrolytic or tantalum output capacitor for proper operation in all applications.
8 |
Power Trends, Inc. 27715 Diehl Road, Warrenville, IL 60555 |
(800) 531-5782 Fax: (630) 393-6902 http://www.powertrends.com |
|
For assistance or to order, call (800) 531-5782
P T 6 2 1 0 S e r i e s
C H A R A C T E R I S T I C D A T A
PT6213, 3.3 VDC (See Note 1)
|
Efficiency vs Output Current |
|
|||
|
100 |
|
|
|
|
|
90 |
|
|
|
|
- % |
|
|
|
|
Vin |
80 |
|
|
|
9.0V |
|
Efficiency |
|
|
|
||
|
|
|
|
26.0V |
|
|
|
|
|
|
12.0V |
|
70 |
|
|
|
15.0V |
|
|
|
|
18.0V |
|
|
|
|
|
|
24.0V |
|
60 |
|
|
|
|
|
50 |
|
|
|
|
|
40 |
|
|
|
|
|
0 |
0.5 |
1 |
1.5 |
2 |
Iout-(Amps)
Efficiency - %
PT6212, 5.0 VDC (See Note 1) |
PT6214, 12.0 VDC (See Note 1) |
Efficiency vs Output Current |
Efficiency vs Output Current |
100 |
|
|
|
|
|
100 |
|
|
|
|
90 |
|
|
|
|
|
90 |
|
|
|
|
80 |
|
|
|
Vin |
- % |
80 |
|
|
|
Vin |
|
|
|
9.0V |
Efficiency |
|
|
|
16.0V |
||
|
|
|
|
12.0V |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
20.0V |
|
|
|
|
|
18.0V |
|
|
|
|
|
|
70 |
|
|
|
|
70 |
|
|
|
24.0V |
|
|
|
|
24.0V |
|
|
|
|
|||
|
|
|
|
|
|
|
|
|||
|
|
|
|
30.0V |
|
|
|
|
|
30.0V |
60 |
|
|
|
38.0V |
|
|
|
|
|
38.0V |
|
|
|
|
|
60 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
50 |
|
|
|
|
|
50 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
40 |
|
|
|
|
|
40 |
|
|
|
|
0 |
0.5 |
1 |
1.5 |
2 |
|
|
|
|
|
|
|
|
|
|
|
|
0 |
0.5 |
1 |
1.5 |
2 |
Iout-(Amps) |
Iout-(Amps) |
Ripple vs Output Current |
Ripple vs Output Current |
|
150 |
|
|
|
|
|
120 |
|
|
|
|
-(mV) |
90 |
|
|
|
|
|
|
|
|
|
|
Ripple |
60 |
|
|
|
|
|
|
|
|
|
|
|
30 |
|
|
|
|
|
0 |
|
|
|
|
|
0 |
0.5 |
1 |
1.5 |
2 |
|
|
150 |
|
|
|
|
|
|
120 |
|
|
|
|
Vin |
|
|
|
|
|
Vin |
|
(mV)- |
|
|
|
|
|
18.0V |
|
|
|
|
|
|
26.0V |
|
|
|
|
|
38.0V |
24.0V |
|
90 |
|
|
|
30.0V |
15.0V |
Ripple |
|
|
|
|
24.0V |
|
|
|
|
18.0V |
||
12.0V |
|
|
|
|
|
|
|
60 |
|
|
|
12.0V |
|
9.0V |
|
|
|
|
||
|
|
|
|
|
9.0V |
|
|
|
|
|
|
|
|
|
|
30 |
|
|
|
|
|
|
0 |
|
|
|
|
|
|
0 |
0.5 |
1 |
1.5 |
2 |
Iout-(Amps) |
Iout-(Amps) |
Thermal Derating (Ta) |
(See Note 2) |
|
2 |
|
|
|
|
70°C |
|
|
1.5 |
|
|
|
|
85°C |
|
|
|
|
|
|
|
|
|
Iout-(Amps) |
1 |
|
|
|
|
|
|
0.5 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
0 |
|
|
|
|
|
|
|
9 |
12 |
15 |
18 |
21 |
24 |
27 |
Vin-(Volts)
Power Dissipation vs Output Current
|
2.5 |
|
|
|
|
|
2 |
|
|
|
|
(Watts) |
|
|
|
|
Vin |
|
|
|
|
15.0V |
|
|
1.5 |
|
|
|
26.0V |
|
|
|
|
|
24.0V |
|
|
|
|
|
18.0V |
- |
|
|
|
|
|
PD |
1 |
|
|
|
12.0V |
|
|
|
|
|
9.0V |
|
0.5 |
|
|
|
|
|
0 |
|
|
|
|
|
0 |
0.5 |
1 |
1.5 |
2 |
Iout-(Amps)
Thermal Derating (Ta) |
(See Note 2) |
|
2 |
|
|
|
|
|
|
|
|
60°C |
|
|
1.5 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
70°C |
|
|
Iout-(Amps) |
|
|
|
|
|
85°C |
|
|
|
|
|
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
0.5 |
|
|
|
|
|
|
|
|
|
|
|
0 |
|
|
|
|
|
|
|
|
|
|
|
9 |
12 |
15 |
18 |
21 |
24 |
27 |
30 |
33 |
36 |
39 |
Vin-(Volts)
Power Dissipation vs Output Current
|
2.5 |
|
|
|
|
(Watts) |
2 |
|
|
|
|
|
|
|
|
24.0V |
|
|
|
|
|
|
Vin |
|
1.5 |
|
|
|
38.0V |
|
|
|
|
30.0V |
|
- |
|
|
|
|
|
PD |
|
|
|
|
18.0V |
|
1 |
|
|
|
12.0V |
|
|
|
|
|
9.0V |
|
0.5 |
|
|
|
|
|
0 |
|
|
|
|
|
0 |
0.5 |
1 |
1.5 |
2 |
Iout-(Amps)
|
Ripple vs Output Current |
|
|||
|
400 |
|
|
|
|
|
350 |
|
|
|
|
|
300 |
|
|
|
Vin |
|
|
|
|
|
|
(mV) |
250 |
|
|
|
38.0V |
|
|
|
|
20.0V |
|
|
|
|
|
|
30.0V |
|
200 |
|
|
|
24.0V |
|
|
|
|
|
|
- |
|
|
|
|
16.0V |
Ripple |
100 |
|
|
|
|
|
150 |
|
|
|
|
|
50 |
|
|
|
|
|
0 |
|
|
|
|
|
0 |
0.5 |
1 |
1.5 |
2 |
Iout-(Amps)
Thermal Derating (Ta) |
(See Note 2) |
|
2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
50°C |
|
|
|
|
|
1.5 |
|
|
|
60°C |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
-(Amps) |
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
70°C |
|
|
|
|
|
||
Iout |
0.5 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
0 |
|
|
|
|
|
|
|
|
|
|
|
|
16 |
18 |
20 |
22 |
24 |
26 |
28 |
30 |
32 |
34 |
36 |
38 |
Vin-(Volts)
Power Dissipation vs Output Current
|
3.5 |
|
|
|
|
|
3 |
|
|
|
|
(Watts) |
2.5 |
|
|
|
30.0V |
|
|
|
|
|
Vin |
|
2 |
|
|
|
38.0V |
- |
|
|
|
|
24.0V |
PD |
1.5 |
|
|
|
|
|
|
|
20.0V |
||
|
|
|
|
||
|
1 |
|
|
|
16.0V |
|
|
|
|
|
|
|
0.5 |
|
|
|
|
|
0 |
|
|
|
|
|
0 |
0.5 |
1 |
1.5 |
2 |
Iout-(Amps)
Note 1: All data listed in the above graphs, except for derating data, has been developed from actual products tested at 25°C. This data is considered typical data for the ISR. Note 2: Thermal derating graphs are developed in free air convection cooling of 40-60 LFM. (See Thermal Application Notes).
Input Wide |
A T A D |
Products Range |
S T E E H S |
|
|
|
|
|
9 |
Power Trends, Inc. 27715 Diehl Road, Warrenville, IL 60555 |
(800) 531-5782 |
Fax: (630) 393-6902 http://www.powertrends.com |
|
|
|
|
|