NE5532ADR |
NE5532, NE5532A, SA5532, SA5532A |
|||||
|
|
|
|
|
DUAL LOW NOISE OPERATIONAL AMPLIFIERS |
|
|
|
|
|
|
SLOS075H − NOVEMBER 1979 − REVISED MAY 2004 |
|
|
|
|
|
|
|
|
|
D Equivalent Input Noise Voltage |
NE5532, NE5532A . . . D, P, OR PS PACKAGE |
||||
|
5 nV/√ |
|
Typ at 1 kHz |
SA5532, SA5532A . . . D OR P PACKAGE |
||
|
Hz |
|||||
|
|
|
|
|
(TOP VIEW) |
DUnity-Gain Bandwidth . . . 10 MHz Typ
D Common-Mode Rejection |
1OUT |
|
|
1 |
8 |
|
|
VCC+ |
Ratio . . . 100 dB Typ |
1IN− |
|
|
2 |
7 |
|
|
2OUT |
D High dc Voltage Gain . . . 100 V/mV Typ |
1IN+ |
|
|
3 |
6 |
|
|
2IN− |
D Peak-to-Peak Output Voltage Swing 32 V |
VCC− |
|
|
4 |
5 |
|
|
2IN+ |
|
|
|
|
|
|
|
||
Typ With VCC± = ±18 V and RL = 600 Ω |
|
|
|
|
|
|
|
|
D High Slew Rate . . . 9 V/µs Typ |
|
|
|
|
|
|
|
|
D Wide Supply-Voltage Range . . . ±3 V to |
|
|
|
|
|
|
|
|
±20 V |
|
|
|
|
|
|
|
|
description/ordering information
The NE5532, NE5532A, SA5532, and SA5532A are high-performance operational amplifiers combining excellent dc and ac characteristics. They feature very low noise, high output-drive capability, high unity-gain and maximum-output-swing bandwidths, low distortion, high slew rate, input-protection diodes, and output short-circuit protection. These operational amplifiers are compensated internally for unity-gain operation. These devices have specified maximum limits for equivalent input noise voltage.
ORDERING INFORMATION
T |
|
PACKAGE† |
ORDERABLE |
TOP-SIDE |
||
|
|
|
|
|||
A |
|
|
|
PART NUMBER |
MARKING |
|
|
|
|
|
|||
|
PDIP − P |
|
Tube of 50 |
NE5532P |
NE5532P |
|
|
|
|
|
|
||
|
|
NE5532AP |
NE5532AP |
|||
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
Tube of 75 |
NE5532D |
N5532 |
|
|
|
|
|
|
||
0°C to 70°C |
SOIC − D |
|
Reel of 2500 |
NE5532DR |
||
|
|
|
||||
|
|
|
|
|
||
|
Tube of 75 |
NE5532AD |
N5532A |
|||
|
|
|
||||
|
|
|
|
|
||
|
|
|
Reel of 2500 |
NE5532ADR |
||
|
|
|
|
|
||
|
|
|
|
|
|
|
|
SOP − PS |
|
Reel of 2000 |
NE5532PSR |
N5532 |
|
|
|
|
|
|
||
|
|
NE5532APSR |
N5532A |
|||
|
|
|
|
|||
|
PDIP − P |
|
Tube of 50 |
SA5532P |
SA5532P |
|
|
|
|
|
|
||
|
|
SA5532AP |
SA5532AP |
|
||
|
|
|
|
|
||
|
|
|
|
|
|
|
−40 °C to 85°C |
|
|
Tube of 75 |
SA5532D |
SA5532 |
|
|
|
|
|
|
||
SOIC − D |
|
Reel of 2500 |
SA5532DR |
|
||
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
Tube of 75 |
SA5532AD |
SA5532A |
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
Reel of 2500 |
SA5532ADR |
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
†Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date. |
Copyright 2004, Texas Instruments Incorporated |
Products conform to specifications per the terms of Texas Instruments |
|
standard warranty. Production processing does not necessarily include |
|
testing of all parameters. |
|
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 |
1 |
NE5532, NE5532A, SA5532, SA5532A
DUAL LOW NOISE OPERATIONAL AMPLIFIERS
SLOS075H − NOVEMBER 1979 − REVISED MAY 2004
schematic (each amplifier)
VCC+ |
36 pF |
IN+ |
37 pF |
14 pF |
15 Ω |
OUT |
7 pF |
IN− |
15 Ω |
460 Ω |
VCC− |
Component values shown are nominal.
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage (see Note 1): VCC+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . . . . . . . 22 V |
VCC− . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . . . . . . −22 V |
Input voltage, either input (see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . . . . . . VCC± |
Input current (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . . . . ±10 mA |
Duration of output short circuit (see Note 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . . . Unlimited |
Package thermal impedance, θJA (see Notes 5 and 6): D package . . . . . . . . . . . . . . . . . . . . . . |
. . . . . . 97°C/W |
P package . . . . . . . . . . . . . . . . . . . . . . |
. . . . . . 85°C/W |
PS package . . . . . . . . . . . . . . . . . . . . . |
. . . . . . 95°C/W |
Operating virtual junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . . . . . 150°C |
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
−65 °C to 150°C |
†Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VCC+ and VCC− .
2.The magnitude of the input voltage must never exceed the magnitude of the supply voltage.
3.Excessive input current will flow if a differential input voltage in excess of approximately 0.6 V is applied between the inputs, unless some limiting resistance is used.
4.The output may be shorted to ground or either power supply. Temperature and/or supply voltages must be limited to ensure the maximum dissipation rating is not exceeded.
5.Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) − T A)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
6.The package thermal impedance is calculated in accordance with JESD 51-7.
2 |
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 |
NE5532, NE5532A, SA5532, SA5532A
DUAL LOW NOISE OPERATIONAL AMPLIFIERS
SLOS075H − NOVEMBER 1979 − REVISED MAY 2004
recommended operating conditions
|
|
|
MIN |
MAX |
UNIT |
|
|
|
|
|
|
|
|
VCC+ |
Supply voltage |
5 |
15 |
V |
||
VCC− |
Supply voltage |
−5 |
−15 |
V |
||
TA |
Operating free-air temperature range |
NE5532, NE5532A |
0 |
70 |
°C |
|
|
|
|
||||
SA5532, SA5532A |
−40 |
85 |
||||
|
|
|
||||
|
|
|
|
|
|
electrical characteristics, VCC± = +15 V, TA = 25°C (unless otherwise noted)
|
|
|
|
|
|
|
NE5532, NE5532A |
|
||
|
PARAMETER |
|
TEST CONDITIONS† |
|
SA5532, SA5532A |
UNIT |
||||
|
|
|
|
|
|
|
MIN |
TYP |
MAX |
|
|
|
|
|
|
|
|
|
|
|
|
VIO |
Input offset voltage |
VO = 0 |
|
TA = 25°C |
|
|
0.5 |
4 |
mV |
|
|
T |
= Full range‡ |
|
|
|
5 |
||||
|
|
|
|
A |
|
|
|
|
|
|
IIO |
Input offset current |
TA = 25°C |
|
|
|
|
|
10 |
150 |
nA |
TA = Full range‡ |
|
|
|
|
200 |
|||||
|
|
|
|
|
|
|
||||
IIB |
Input bias current |
TA = 25°C |
|
|
|
|
|
200 |
800 |
nA |
TA = Full range‡ |
|
|
|
|
1000 |
|||||
|
|
|
|
|
|
|
||||
VICR |
Common-mode input-voltage range |
|
|
|
|
|
±12 |
±13 |
|
V |
VOPP |
Maximum peak-to-peak |
RL ≥ 600 Ω |
|
VCC± = ±15 V |
|
24 |
26 |
|
V |
|
output-voltage swing |
|
VCC± = ±18 V |
|
30 |
32 |
|
||||
|
|
|
|
|
|
|
||||
|
|
RL ≥ 600 Ω, |
|
TA = 25°C |
|
15 |
50 |
|
|
|
|
Large-signal |
VO = ±10 V |
|
T |
= Full range‡ |
|
10 |
|
|
|
AVD |
|
|
A |
|
|
|
|
|
V/mV |
|
differential-voltage amplification |
RL ≥ 2 kΩ, |
|
TA = 25°C |
|
25 |
100 |
|
|||
|
|
VO = ±10 V |
|
T |
= Full range‡ |
|
15 |
|
|
|
|
|
|
|
A |
|
|
|
|
|
|
Avd |
Small-signal |
f = 10 kHz |
|
|
|
|
|
2.2 |
|
V/mV |
differential-voltage amplification |
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
BOM |
Maximum-output-swing bandwidth |
RL = 600 Ω |
|
VO = ±10 V |
|
|
140 |
|
kHz |
|
|
VCC± = ±18 V, |
VO = ±14 V |
|
100 |
|
|||||
|
|
|
|
|
|
|
||||
B1 |
Unity-gain bandwidth |
RL = 600 Ω, |
|
CL = 100 pF |
|
|
10 |
|
MHz |
|
ri |
Input resistance |
|
|
|
|
|
30 |
300 |
|
kΩ |
zo |
Output impedance |
AVD = 30 dB, |
|
RL = 600 Ω, |
f = 10 kHz |
|
0.3 |
|
Ω |
|
CMRR |
Common-mode rejection ratio |
VIC = VICR min |
|
|
|
|
70 |
100 |
|
dB |
kSVR |
Supply-voltage rejection ratio |
VCC± = ±9 V to |
±15 V, |
|
VO = 0 |
80 |
100 |
|
dB |
|
(∆VCC±/∆VIO) |
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
IOS |
Output short-circuit current |
|
|
|
|
|
10 |
38 |
60 |
mA |
ICC |
Total supply curent |
VO = 0, |
|
No load |
|
|
8 |
16 |
mA |
|
|
Crosstalk attenuation (VO1/VO2) |
V01 = 10 V peak, f = 1 kHz |
|
|
110 |
|
dB |
†All characteristics are measured under open-loop conditions, with zero common-mode input voltage, unless otherwise specified.
‡ Full temperature ranges are: − 40 °C to 85°C for the SA5532 and SA5532A, and 0°C to 70°C for the NE5532 and NE5532A.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 |
3 |