3-065-677-11 (1) GB
Video Cassette
Recorder
Operating Instructions
PAL
SLV-SE610G
SLV-SE710G
SLV-SE710I
SLV-SE810G
© 2001 Sony Corporation
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Mains lead must only be changed at a qualified service shop.
Notice for customers in the United Kingdom and Republic of Ireland
A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience.
If the 13A fitted plug does not match the outlet socket in your home, please refer to your Appointed Sony Dealer for advice.
Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or BSI to BS1362, (i.e., marked with or mark) must be used.
If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.
Precautions
Safety
•This unit operates on 220 – 240 V AC, 50 Hz. Check that the unit’s operating voltage is identical with your local power supply.
•If anything falls into the cabinet, unplug the unit and have it checked by qualified personnel before operating it any further.
•The unit is not disconnected from the mains as long as it is connected to the mains, even if the unit itself has been turned off.
•Unplug the unit from the wall outlet if you do not intend to use it for an extended period of time. To disconnect the cord, pull it out by the plug, never by the cord.
Installing
•Allow adequate air circulation to prevent internal heat buildup.
•Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation slots.
•Do not install the unit near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock.
•Do not install the unit in an inclined position. It is designed to be operated in a horizontal position only.
•Keep the unit and cassettes away from equipment with strong magnets, such as microwave ovens or large loudspeakers.
•Do not place heavy objects on the unit.
•If the unit is brought directly from a cold to a warm location, moisture may condense inside the VCR and cause damage to the video head and tape. When you first install the unit, or when you move it from a cold to a warm location, wait for about three hours before operating the unit.
Caution
Television programmes, films, video tapes and other materials may be copyrighted. Unauthorized recording of such material may be contrary to the provisions of the copyright laws. Also, use of this recorder with cable television transmission may require authorization from the cable television transmitter and/or programme owner.
Compatible colour systems
This VCR is designed to record and play back using the PAL colour system. Recording of video sources based on other colour systems cannot be guaranteed.
VIDEO Plus+ and PlusCode are registered trademarks of Gemstar Development Corporation. The VIDEO Plus+ system is manufactured under license from Gemstar Development Corporation.
2 WARNING
Table of contents
Getting Started
4 Index to parts and controls
10Step 1 : Unpacking
11Step 2 : Setting up the remote commander
15 Step 3 : Connecting the VCR
19Step 4 : Setting up the VCR with the Auto Set Up function
21Step 5 : Tuning your TV to the VCR
23Selecting a language
24Presetting channels
27Changing/disabling programme positions
32 Setting the clock
36 Setting your personal code
Basic Operations
38 Playing a tape
40 Recording TV programmes
43Recording TV programmes using the Dial Timer (SLV-SE810G only)
48Recording TV programmes using the VIDEO Plus+ system
(not available on SLV-SE610G)
52Recording TV programmes using the timer
Additional Operations
56 Playing/searching at various speeds
58Setting the recording duration time
59Synchronized Recording
(not available on SLV-SE610G)
61Checking/changing/cancelling timer settings
63Recording stereo and bilingual programmes
65Searching using the Smart Search function
67Storing, searching and deleting programme information (Smart Search Plus)
72Searching using the index function
73Adjusting the picture
75Reducing the VCR’s power consumption
76Changing menu options
Editing
79Connecting to a VCR or stereo system
81Basic editing
82Audio dubbing (SLV-SE810G only)
Additional Information
83 Troubleshooting
87Specifications
88Index
Back Cover
Quick Start Guide
Started Getting
Table of contents 3
Getting Started
Refer to the pages indicated in parentheses ( ) for details.
SLV-SE810G
A?/1(on/standby) switch (36) |
M DIAL TIMER (43) |
|
BTape compartment |
NPROGRAM +/– buttons (22) (57) |
|
CRemote sensor (11) |
(73) |
|
OAUDIO DUB button (82) |
||
DA(eject) button (38) |
||
PAUTO SET UP/RF (Radio |
||
EShuttle ring (56) |
||
Frequency) CHANNEL button (19) |
||
|
||
FH(play) button (38) (56) |
(21) |
|
|
||
GJOG button (57) |
QSYNCHRO REC (Synchronized |
|
Recording) button (59) |
||
HzREC (record) button (40) (58) |
||
|
(81)Rt LINE-2 L (left) oR (right) jacks (covered) (79) (80)
IX(pause) button (38) (81)
Jx(stop) button (38) (81)
KM(fast-forward) button (38) (56)
Lm(rewind) button (38) (56)
How to open the jack cover
1Press the bottom of the cover.
2Hook your finger on the top edge of the cover and pull it open.
4 Index to parts and controls
SLV-SE610G, SE710G, SE710I
Started Getting
A?/1(on/standby) switch (36)
BTape compartment
CRemote sensor (11)
DA(eject) button (38)
EH(play) button (38) (56)
FzREC (record) button (40) (58)
IM(fast-forward) button (38) (56)
Jm(rewind) button (38) (56)
KPROGRAM +/– buttons (22) (57) (73)
LAUTO SET UP/RF (Radio Frequency) CHANNEL button (19) (21)
(81)MSYNCHRO REC (Synchronized
GX(pause) button (38) (81) |
Recording) button* (59) |
|
|
Hx(stop) button (38) (81) |
|
* not available on SLV-SE610G |
|
continued
Index to parts and controls 5
STEREO |
NICAM |
VIDEO |
VPS SPLP |
OPC |
|
SYNCHRO |
|
PDC |
EP |
TV |
|
|
RR |
|
|
|
|
ATimer indicator (45) (50) (53)
BSYNCHRO indicator*1 (60)
CSTEREO indicator (63)
DNICAM indicator (63)
E (smartlink) indicator*1 (17)
FVIDEO indicator (16) (41)
GVPS (Video Programme System)/ PDC (Programme Delivery Control) indicator*1 (50)
HTape speed indicators (40)
IOPC (Optimum Picture Control) indicator (74)
*1not available on SLV-SE610G *2SLV-SE810G only
JTV indicator*1 (42)
KAudio dubbing indicator*2 (82)
LTracking indicator (73)
MTime counter/clock/line/programme position indicator (38) (40) (81)
NRemaining time indicator (40)
ORR (Reality Regenerator) indicator (73)
PTape/recording indicator (40)
6 Index to parts and controls
Started Getting
AMains lead (15) (16)
Bt LINE-2 IN
tENTREE LIGNE-2 connector*1 (18) (59) (80)
tLINE-3 IN
tENTREE LIGNE-3 connector*2 (18) (59) (80)
CAERIAL IN
ANTENNE ENTREE connector (15) (16)
*1SLV-SE710G, and SE710I only *2SLV-SE810G only
*3not available on SLV-SE610G
DAERIAL OUT
ANTENNE SORTIE connector (15) (16)
Ei LINE-1 (TV)
i LIGNE-1 (TV) connector (16) (79)
F (audio out) R/D (right) L/G (left) jacks*3 (18)
continued
Index to parts and controls 7
1 2 3
4 5 6
7 8 9
0
AZEJECT button (38)
BWIDE button (for TV) (13)
CAUDIO MONITOR button (63)
D× 2 button*1 (56)
EySLOW button*1 (56)
FSP (Standard Play)/LP (Long Play) button (40)
G DISPLAY button (40)
H- (ten’s digit) button (12) (41)
I2(volume) +/– buttons (for TV) (13)
JzREC (record) button (40) (58)
KMENU button (32) (61)
LXPAUSE/M button (32) (38) xSTOP/m button (32) (38)
mREW (rewind)/< button (38) (56)
MFF (fast-forward)/, button (38) (56)
HPLAY/OK button (32) (38)
*1FASTEXT buttons (for TV) (not available on SLV-SE610G, SE710G, SE710I)
*2not available on SLV-SE610G, SE710G, SE710I
8 Index to parts and controls
1 2 3
4 5 6
7 8 9
0
M[TV] / [VIDEO] remote control switch (11)
N?/1(on/standby) switch (12) (50)
OCOUNTER/REMAIN button (40)
/ (Teletext) button*2 (for TV) (13)
PaTV power on/TV mode select button*2 (for TV) (12)
Q./>INDEX SEARCH buttons*1 (72)
RCLEAR button (38) (49) (61)
St TV/VIDEO button (12) (16) (41)
TProgramme number buttons (12) (41)
UINPUT SELECT button (41) (53) (81)
VPROG (programme) +/– buttons (12) (25) (40)
c/CTeletext page access buttons*2 (for TV) (13)
W TIMER button (48) (52)
XSMART SEARCH button (65)
*1FASTEXT buttons (for TV) (not available on SLV-SE610G, SE710G, SE710I)
*2not available on SLV-SE610G, SE710G, SE710I
Started Getting
Index to parts and controls 9
Check that you have received the following items with the VCR:
• Remote commander |
• Aerial cable |
• R6 (size AA) batteries
The instructions in this manual are for the 4 models: SLV-SE610G, SE710G, SE710I, and SE810G. Check your model number by looking at the rear panel of your VCR.
SLV-SE810G is the model used for illustration purposes. Any difference in operation is clearly indicated in the text, for example, “SLV-SE610G only.”
10 Unpacking
Insert two R6 (size AA) batteries by matching the + and
– on the batteries to the diagram inside the battery compartment.
Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position.
You can use this remote commander to operate this VCR and a Sony TV. Buttons on the remote commander marked with a dot (•) can be used to operate your Sony TV. If the TV does not have the symbol near the remote sensor, this remote commander will not operate the TV.
Remote sensor
[TV] / [VIDEO]
Started Getting
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
9 |
|
0 |
|
To operate |
Set [TV] / [VIDEO] to |
|
|
the VCR |
[VIDEO] and point at the remote sensor at the VCR |
|
|
a Sony TV |
[TV] and point at the remote sensor at the TV |
|
|
continued
Setting up the remote commander 11
|
|
|
?/1 |
|
WIDE |
|
|
/ |
|
AUDIO MONITOR |
|
|
a |
|
FASTEXT buttons |
|
|
|
|
DISPLAY |
|
|
t TV/VIDEO |
|
1 |
2 |
3 |
|
|
4 |
5 |
6 |
Programme |
|
7 |
8 |
9 |
number |
|
buttons |
||||
|
|
|
||
- |
0 |
|
|
PROG +/–/ c/C
2 +/–
TV control buttons
|
|
|
To |
Press |
|
|
|
|
|
|
|
|
Set the TV to standby mode |
?/1 |
|
|
|
|
|
|
|
|
Select an input source: aerial in or line in |
tTV/VIDEO |
|
|
|
|
|
|
|
|
Select the TV’s programme position |
Programme number buttons, |
|
|
|
|
-, PROG +/– |
12 |
|
|
|
|
|
Setting up the remote commander |
|
||
|
|
|||
|
|
|
|
|
To |
Press |
|
|
Adjust the volume of the TV |
2+/– |
|
|
Switch to TV (Teletext off)* |
a (TV) |
|
|
Switch to Teletext* |
/ (Teletext) |
|
|
Select the sound |
AUDIO MONITOR |
|
|
Use FASTEXT* |
FASTEXT buttons |
|
|
Call up the on-screen display |
DISPLAY |
|
|
Change the Teletext page* |
c/C |
|
|
Switch to/from wide mode of a Sony wide TV (For |
WIDE |
other manufactures’ wide TVs, see “Controlling |
|
other TVs with the remote commander |
|
(SLV-SE810G only)” below.) |
|
|
|
Notes
•With normal use, the batteries should last about three to six months.
•If you do not use the remote commander for an extended period of time, remove the batteries to avoid possible damage from battery leakage.
•Do not use a new battery together with an old one.
•Do not use different types of batteries together.
•Some buttons may not work with certain Sony TVs.
* not available on SLV-SE610G, SE710G, and SE710I
The remote commander is preprogrammed to control non-Sony TVs. If your TV is listed in the following table, set the appropriate manufacturer’s code number.
1 Set [TV] / [VIDEO] at the top of the remote commander to [TV].
2 Hold down ?/1, and enter your TV’s code number using the programme number buttons. Then release ?/1.
Now you can use the following TV control buttons to control your TV:
?/1, tTV/VIDEO, programme number buttons, - (ten’s digit), PROG +/–, 2+/–, a (TV), / (Teletext), FASTEXT buttons, WIDE*, MENU*, M/m/</,*, and OK*.
* These buttons may not work with all TVs.
Started Getting
continued
Setting up the remote commander 13
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until you find the one that works with your TV.
To switch to wide mode, see the footnotes below this table for the applicable code numbers.
Manufacturer |
Code number |
|
|
Sony |
01*1, 02 |
|
|
Akai |
68 |
|
|
Ferguson |
52 |
|
|
Grundig |
10*1, 11*1 |
|
|
Hitachi |
24 |
|
|
JVC |
33 |
|
|
Loewe |
45 |
|
|
Mivar |
09, 70 |
|
|
NEC |
66 |
|
|
Manufacturer |
Code number |
|
|
Nokia |
15, 16, 69*3 |
|
|
Panasonic |
17*1, 49 |
|
|
Philips |
06*1, 07*1, 08*1 |
|
|
Saba |
12, 13 |
|
|
Samsung |
22, 23 |
|
|
Sanyo |
25 |
|
|
Sharp |
29 |
|
|
Telefunken |
36 |
|
|
Thomson |
43*2 |
|
|
Toshiba |
38 |
|
|
*1 Press WIDE to switch the wide picture mode on or off.
*2 Press WIDE, then press 2+/– to select the wide picture mode you want.
*3 Press WIDE. The menu appears on the TV screen. Then, press M/m/</, to select the wide picture you want and press OK.
Tip
•When you set your TV’s code number correctly while the TV is turned on, the TV turns off automatically.
Notes
•If you enter a new code number, the code number previously entered will be erased.
•If the TV uses a different remote control system from the one programmed to work with the VCR, you cannot control your TV with the remote commander.
•When you replace the batteries of the remote commander, the code number may change. Set the appropriate code number every time you replace the batteries.
14 Setting up the remote commander
If your TV has a Scart (EURO-AV) connector, see page 16.
Mains lead
to mains
AERIAL IN |
AERIAL OUT
AERIAL IN
Aerial cable (supplied)
: Signal flow
1 |
Disconnect the aerial cable from |
AERIAL |
your TV and connect it to |
ANTENNE |
|
|
IN |
|
|
AERIAL IN on the rear panel of |
ENTREE |
|
|
|
|
the VCR. |
OUT |
|
|
SORTIE |
2 |
Connect AERIAL OUT of the |
IN |
|
AERIAL |
ANTENNE
VCR and the aerial input of your
ENTREE
TV using the supplied aerial cable.
OUT
SORTIE
3 |
Connect the mains lead to the mains. |
|
Note
•When you connect the VCR and your TV only with an aerial cable, you have to tune your TV to the VCR (see page 21).
Started Getting
continued
Connecting the VCR 15
AERIAL IN |
|
i LINE-1 |
AERIAL OUT |
Mains lead |
(TV) |
|
|
|
|
to mains |
|
AERIAL IN |
|
|
|
|
|
Aerial cable (supplied) |
: Signal flow |
|
|
|
|
Scart cable (not supplied) |
Scart
(EURO-AV)
1
2
3
4
Disconnect the aerial cable from |
AERIAL |
your TV and connect it to |
ANTENNE |
IN |
|
AERIAL IN on the rear panel of |
ENTREE |
|
|
the VCR. |
OUT |
|
SORTIE |
Connect AERIAL OUT of the |
AERIAL |
VCR and the aerial input of your |
ANTENNE |
IN |
|
ENTREE |
|
TV using the supplied aerial cable. |
|
|
OUT |
|
SORTIE |
Connect LINE-1 (TV) on the VCR |
|
and the Scart (EURO-AV) |
|
connector on the TV with the |
|
optional Scart cable. |
|
This connection improves picture |
|
and sound quality. Whenever you |
|
want to watch the VCR picture, |
|
press tTV/VIDEO to display |
|
the VIDEO indicator in the |
|
display window. |
|
Connect the mains lead to the mains. |
|
Note
•If the TV is connected to the LINE-1 (TV) connector, setting the RF channel to OFF is recommended. In the OFF position, only the signal from the aerial is output through the AERIAL OUT connector (see page 22).
16 Connecting the VCR
If the connected TV complies with
SMARTLINK, MEGALOGIC*1, EASYLINK*2, Q-Link*3, EURO
VIEW LINK*4, or T-V LINK*5, this VCR automatically runs the
SMARTLINK function after you complete the steps on the previous page (the indicator appears in the VCR’s display window when you turn on the TV). You can enjoy the following SMARTLINK features.
•Preset Download
You can download your TV tuner preset data to this VCR and tune the VCR according to that data in Auto Set Up. This greatly simplifies the Auto Set Up procedure. Be careful not to disconnect the cables or exit the Auto Set Up function during the procedure.
See “Setting up the VCR with the Auto Set Up function” on page 19.
•TV Direct Rec
You can easily record what you are watching on the TV. For details, see “Recording what you are watching on the TV (TV Direct Rec) (not available on SLV-SE610G)” on page 42.
•One Touch Play
With One Touch Play, you can start playback automatically without turning on the TV. For details, see “Starting playback automatically with one button (One Touch Play) (not available on SLV-SE610G)” on page 39.
•One Touch Menu
You can turn on the VCR and TV, set the TV to the video channel, and display the VCR’s on-screen display automatically by pressing MENU on the remote commander.
•One Touch Timer
You can turn on the VCR and TV, set the TV to the video channel, and display the timer recording menu (the TIMER METHOD menu, the
TIMER menu, or the VIDEO Plus+ menu) automatically by pressing TIMER on the remote commander.
You can set which timer recording menu is displayed using TIMER OPTIONS in the OPTIONS-2 menu (see page 77).
•Automatic Power Off
You can have the VCR turn off automatically, if the VCR is not used after you turn off the TV.
*1 “MEGALOGIC” is a registered trademark of Grundig Corporation. *2 “EASYLINK” is a trademark of Philips Corporation.
*3 “Q-Link” is a trademark of Panasonic Corporation.
*4 “EURO VIEW LINK” is a trademark of Toshiba Corporation. *5 “T-V LINK” is a trademark of JVC Corporation.
Started Getting
continued
Connecting the VCR 17
Note
• Not all TVs respond to the functions above.
To a stereo system (not available on SLV-SE610G)
You can improve sound quality by connecting a stereo system to the R/D L/G jacks as shown on the right.
To a set top box with Line Through
(not available on SLV-SE610G)
R/D L/G
LINE IN
Audio cable (not supplied) : Signal flow
LINE OUT
Using the Line Through function, you can watch programmes from a set top box connected to this VCR on the TV even when the VCR is turned off. When you turn on the set top box, this VCR automatically sends the signal from the set top
box to the TV without turning itself on.
1 Connect the set top box to the LINE-3 IN*1 (or LINE-2 IN*2) connector as shown above.
2 Set POWER SAVE to OFF or PARTIAL*1 in the OPTIONS-2 menu.
3 Turn off the VCR.
To watch a programme, turn on the set top box and the TV.
Note
•You cannot watch programmes on the TV while recording unless you are recording a programme from your set top box.
*1 SLV-SE810G only *2SLV-SE710G and SE710I only
18 Connecting the VCR
Before using the VCR for the first time, set up the VCR using the Auto Set Up function. With this function, you can set the TV channels, guide channels for the VIDEO Plus+ system*, RF cheannel, and VCR clock* automatically.
AUTO SET UP
Started Getting
AUTO
SET UP
RF CHANNEL
Hold down AUTO SET UP on the VCR for more than three seconds.
The VCR automatically turns on, and starts searching for all of the receivable channels and presets them in the appropriate order for your local area*.
If you want to change the order of the channels or disable unwanted programme positions, see “Changing/disabling programme positions” on page 27.
If you use the SMARTLINK connection (not available on SLVSE610G), the Preset Download function starts and the indicator flashes in the display window during download.
After the search or download is complete, the current time appears in the display window for any stations that transmit a time signal (not available on SLV-SE610G). If the time does not appear, set the clock manually (see page 32).
To cancel the Auto Set Up function
Press AUTO SET UP.
continued
Setting up the VCR with the Auto Set Up function 19
Notes
•If you stop the Auto Set Up function during step 3, you must repeat set up from step 1.
•Whenever you operate the Auto Set Up function, some of the settings (VIDEO Plus+*, timer, etc.) will be reset. If this happens, you have to set them again.
* not available on SLV-SE610G
20 Setting up the VCR with the Auto Set Up function
If your TV has a Scart (EURO-AV) connector, see page 22.
Follow the steps below so that your TV will properly receive the video signals from your VCR.
RF CHANNEL
PROGRAM +/–
1 |
AUTO |
Press RF CHANNEL on the VCR lightly. |
|
||
|
|
|
|
SET UP |
The factory-preset RF channel appears in the display window. |
|
|
|
|
|
The VCR signal is output through this channel to the TV. |
Started Getting
RF CHANNEL
2
3
Turn on your TV and select a programme position for the VCR picture.
This programme position will now be referred to as the video channel.
Tune the TV to the same channel shown in the VCR display window so
that the picture on the right appears SONY VIDEO CASSETTE RECORDER clearly on the TV screen.
Refer to your TV manual for TV tuning instructions.
If the picture does not appear clearly, see “To obtain a clear picture from the VCR” below.
continued
Tuning your TV to the VCR 21
4 |
AUTO |
Press RF CHANNEL. |
SET UP |
|
You have now tuned your TV to the VCR. Whenever you want to play a tape, set the TV to the video channel.
RF CHANNEL
To check to see if the TV tuning is correct
Set the TV to the video channel and press PROGRAM +/– on the VCR. If the TV screen changes to a different programme each time you press PROGRAM +/–, the TV tuning is correct.
To obtain a clear picture from the VCR
If the screen does not appear clearly in step 3 above, press PROGRAM +/– so that another RF channel appears. Then tune the TV to the new RF channel so that a clear picture appears.
RF CHANNEL
PROGRAM +/–
1 |
AUTO |
SET UP |
RF CHANNEL
Press RF CHANNEL on the VCR lightly.
The factory-preset RF channel appears in the display window.
The VCR signal is output through this channel to the TV.
2 |
PROGRAM |
Press PROGRAM +/– to set the RF channel to OFF, and press RF |
|
CHANNEL again.
AUTO
SET UP
RF channel set up is complete.
RF CHANNEL
22 Tuning your TV to the VCR
If you prefer an on-screen language other than English, use the on-screen display to select another language.
Before you start…
•Turn on the VCR and the TV.
•Set the TV to the video channel.
•Refer to “Index to parts and controls” for button locations.
1 |
MENU |
Press MENU, then press M/m to |
SETTINGS |
|
|
highlight SETTINGS and press OK. |
|
|
|||
|
|
|
|||
|
|
TUNER |
|
|
|
|
|
CLOCK |
|
|
|
|
|
LANGUAGE |
|
|
|
|
|
RETURN |
|
|
|
|
PLAY |
|
|
|
|
|
|
SELECT : |
|
|
|
|
OK |
SET |
: OK |
EXIT |
: MENU |
|
|
|
|||
|
|
|
|
||
2 |
|
Press M/m to highlight LANGUAGE, |
LANGUAGE |
|
|
|
|
|
|
||
|
|
then press OK. |
|
|
|
|
PLAY |
ENGLISH |
NEDERLANDS |
|
|
|
|
|
|||
|
|
|
DEUTSCH |
DANSK / NORSK |
|
|
OK |
|
FRANÇ AIS |
SVENSKA |
|
|
|
ITALIANO |
SUOMI |
|
|
|
|
|
ESPAÑ OL |
|
|
|
|
|
PORTUGUÊ S |
|
|
|
|
SELECT : |
|
|
|
|
|
SET |
: OK |
EXIT |
: MENU |
|
|
|
|
3 |
Press M/m/</, to highlight the desired language, then press OK. |
|
|
|
PLAY |
|
OK |
4 |
Press MENU to exit the menu. |
MENU |
Tip
• If you want to return to the previous menu, highlight RETURN and press OK.
Note
•The menu disappears automatically if you don’t proceed for more than a few minutes.
Started Getting
Selecting a language 23
If some channels could not be preset using the Auto Set Up function, you can preset them manually.
Before you start…
•Turn on the VCR and the TV.
•Set the TV to the video channel.
•Refer to “Index to parts and controls” for button locations.
1 MENU
PLAY
OK
Press MENU, then press M/m to highlight SETTINGS and press OK.
SETTINGS |
|
|
TUNER |
|
|
CLOCK |
|
|
LANGUAGE |
|
|
RETURN |
|
|
SELECT |
: |
|
SET |
: OK |
|
|
EXIT |
: MENU |
2 |
Press M/m to highlight TUNER, then |
|
|
|
press OK. |
|
PLAY |
|
OK |
ex. SLV-SE710I
TUNER |
|
PROG. |
1 |
|
|
||
NORMAL / CATV |
NORMAL |
|
|
CHANNEL SET |
C1 2 |
AAB |
|
PAY - TV / CANAL+ |
OFF |
|
|
AFT |
ON |
|
|
FINE TUNING |
|
|
|
RETURN |
|
|
|
SELECT :
SET : OK
EXIT : MENU
3
PLAY
OK
SLV-SE710I only:
Press M/m to highlight NORMAL/ CATV, then press OK.
TUNER |
PROG. |
1 |
||
|
|
|||
NORMAL / CATV |
NORMAL |
|
|
|
CHANNEL SET |
CATV |
|
|
|
PAY - TV / CANAL+ |
|
|
|
|
AFT |
|
ON |
|
|
FINE TUNING |
|
|
|
|
RETURN |
|
|
|
|
SELECT |
: |
|
|
|
CONFIRM |
: OK |
EXIT |
: MENU |
|
|
|
4
PLAY
OK
SLV-SE710I only:
Press M/m to highlight NORMAL, then press OK.
To preset CATV (Cable Television) channels, select CATV.
TUNER |
|
PROG. |
1 |
|
|
||
NORMAL / CATV |
NORMAL |
|
|
CHANNEL SET |
C1 2 |
AAB |
|
PAY - TV / CANAL+ |
OFF |
|
|
AFT |
ON |
|
|
FINE TUNING |
|
|
|
RETURN |
|
|
|
SELECT :
SET : OK
EXIT : MENU
24 Presetting channels
5 |
• PROG |
Press PROG +/– to select the |
|
programme position.
Selected programme
position |
|
|
|
Getting |
TUNER |
|
PROG. |
4 |
|
|
|
|||
NORMAL / CATV |
NORMAL |
|
||
CHANNEL SET |
C1 2 |
AAB |
|
|
|
Started |
|||
PAY - TV / CANAL+ |
OFF |
|
|
|
AFT |
ON |
|
|
|
FINE TUNING |
|
|
|
|
RETURN |
|
|
|
|
|
|
|
|
SELECT :
SET : OK
EXIT : MENU
6 |
Press M/m to highlight CHANNEL |
|
|
|
SET, then press OK. |
|
PLAY |
|
OK |
TUNER |
PROG. |
4 |
||
|
|
|||
NORMAL / CATV |
|
|
|
|
CHANNEL SET |
C1 2 |
AAB |
|
|
PAY - TV / CANAL+ |
|
|
|
|
AFT |
|
ON |
|
|
FINE TUNING |
|
|
|
|
RETURN |
|
|
|
|
SELECT |
: |
|
|
|
CONFIRM |
: OK |
EXIT |
: MENU |
|
|
|
7
PLAY
OK
1 2
4 5
7 8
0
Press M/m repeatedly until the channel you want is displayed.
|
The channels appear in the following |
|
|
|
|
|
|
|
|
|
|
|
TUNER |
|
|
|
|
|
order: |
|
|
|
|
PROG. 4 |
|
|
|
|
|
NORMAL / CATV |
|
|
|
||
|
|
|
|
|
|
|
||
|
• VHF IA-IJ, SA10-SA13 (SLV- |
|
|
CHANNEL SET |
C2 7 |
|
|
|
|
|
|
PAY - TV / CANAL+ |
|
|
|
||
|
SE710I only) |
|
|
AFT |
ON |
|
|
|
|
|
|
FINE TUNING |
|
|
|
||
|
|
|
RETURN |
|
|
|
||
3 |
• UHF B21 - B69 |
|
|
|
|
|
|
|
6 |
|
|
|
|
|
|
|
|
• CATV S1 - S20 (SLV-SE710I only) |
|
SELECT : |
|
|
|
|||
|
|
|
|
|
||||
9 |
• HYPER S21 - S41 (SLV-SE710I |
|
CONFIRM : OK |
EXIT : MENU |
||||
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
only) |
|
|
|
|
|
|
|
|
• CATV S01 - S05 (SLV-SE710I only) |
|
|
|
|
|
|
|
|
If you know the number of the channel you want, press the |
|||||||
|
programme number buttons. For example, for channel 5, first press |
|||||||
|
“0” and then press “5.” |
|
|
|
|
|
|
8 |
To preset another programme position, repeat steps 5 through 7. |
|
|
|
|
9 |
Press MENU to exit the menu. |
MENU |
|
|
|
continued
Presetting channels 25
Normally, the Auto Fine Tuning (AFT) function automatically tunes in channels clearly. However, if the picture is not clear, you may also use the manual tuning function.
1 Press PROG +/– or the programme number buttons to select the programme position for which you cannot obtain a clear picture.
2 Press MENU, then select SETTINGS and press OK.
3 Select TUNER, then press OK.
4 Select FINE TUNING, then press OK. The fine tuning meter appears.
TUNER
PROG. 4
|
NORMAL / CATV |
NORMAL |
|
|||
|
CHANNEL SET |
C2 7 |
|
|||
|
PAY - TV / CANAL+ |
OFF |
|
|||
|
AFT |
|
|
|
|
|
|
FINE TUNING |
|
|
|
|
|
|
RETURN |
|
|
|
|
|
|
|
|
|
|
|
|
SET : |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
EXIT : |
MENU |
Selected programme position
5 Press </,to get a clearer picture, then press MENU to exit the menu. Note that the AFT (Auto Fine Tuning) setting switches to OFF.
Tip
• If you want to return to the previous menu, highlight RETURN and press OK.
Notes
•The menu disappears automatically if you don’t proceed for more than a few minutes.
•When adjusting FINE TUNING, the menu may become difficult to read due to interference from the picture being received.
26 Presetting channels
After setting the channels, you can change the programme positions as you like. If any programme positions are unused or contain unwanted channels, you can disable them.
You can also change the station names (not available on SLV-SE610G). If the station names are not displayed, you can enter them manually.
Before you start…
•Turn on the VCR and the TV.
•Set the TV to the video channel.
•Refer to “Index to parts and controls” for button locations.
1 |
MENU |
Press MENU, then press M/m to |
LISTS |
|
highlight LISTS and press OK. |
|
|||
|
|
|||
|
|
CHANNEL LIST |
|
|
|
|
TIMER LIST |
|
|
|
|
RETURN |
|
|
|
PLAY |
|
|
|
|
|
SELECT : |
|
|
|
OK |
SET |
: OK |
|
|
|
EXIT |
: MENU |
|
|
|
|
2 |
Press M/m to highlight CHANNEL |
|
|
|
CHANNEL LIST |
|
|
|
LIST, then press OK. |
|
|
PLAY |
PROG |
CH |
NAME |
|
1 |
C1 2 |
AAB |
OK |
2 |
C0 3 |
CDE |
3 |
C5 6 |
|
|
|
4 |
C2 7 |
|
|
5 |
C0 9 |
FGH |
|
SELECT |
: |
|
|
MOVE PROGRAM |
: |
|
|
ERASE PROGRAM |
: CLEAR |
|
EXIT : MENU
3
PLAY
OK
Press M/m to highlight the row which you want to change the programme position, then press ,.
To display other pages for programme positions 6 to 60, press M/m repeatedly.
CHANNEL LIST
PROG |
CH |
NAME |
1 |
C1 2 |
AAB |
2 |
C0 3 |
CDE |
3C5 6
4C2 7
5 |
C0 9 |
|
|
|
FGH |
|
|
|
|
|
|
|
|
SELECT |
|
: |
|
|
|
|
|
|
|
|
|
||
SET STATION NAME |
|
: |
|
|
|
|
CONFIRM |
|
: |
OK |
|
EXIT : MENU
Started Getting
continued
Changing/disabling programme positions 27
4
PLAY
OK
Press M/m until the selected channel row moves to the desired programme position.
The selected channel is inserted at the new programme position and the intermediate channels are displaced to fill the gap.
CHANNEL LIST
|
PROG |
CH |
|
|
|
NAME |
|
||
|
1 |
|
C0 3 |
|
|
|
CDE |
|
|
2 |
|
C5 6 |
|
|
|
|
|
|
|
|
3 |
|
C1 2 |
|
|
|
AAB |
|
|
|
4 |
|
C2 7 |
|
|
|
|
|
|
5 |
|
C0 9 |
|
|
|
FGH |
|||
|
|
|
|
|
|
|
|
|
|
SELECT |
|
: |
|
|
|
|
|
||
|
|
|
|
|
|
||||
SET STATION NAME |
|
: |
|
|
|
|
|
||
CONFIRM |
|
: |
OK |
|
EXIT : MENU
5 |
Press OK to confirm the setting. |
|
PLAY
OK
6
7
To change the programme position of another station, repeat steps 3 through 5.
Press MENU to exit the menu.
MENU
Tip
• If you want to return to the previous menu, highlight RETURN and press OK.
Note
•The menu disappears automatically if you don’t proceed for more than a few minutes.
After presetting channels, you can disable unused programme positions. The disabled positions will be skipped later when you press the PROG +/– buttons.
Before you start…
•Turn on the VCR and the TV.
•Set the TV to the video channel.
•Refer to “Index to parts and controls” for button locations.
1 |
MENU |
Press MENU, then press M/m to |
|
highlight LISTS, and press OK. |
|||
|
|
PLAY
OK
LISTS |
|
|
CHANNEL LIST |
|
|
TIMER LIST |
|
|
RETURN |
|
|
SELECT |
: |
|
SET |
: OK |
|
|
EXIT |
: MENU |
28 Changing/disabling programme positions